Problem with making call on my PAP2T

I've configured my PAP2T, and got a strange issue: each reboot of the PAP2T device will only allow me to make one call, each call after that will get a busy signal. Please help me!!! Thanks!

The device has software version 5.1.6(LS) and hardware version 0.1.5. I've tried both 2-wire cable and 4-wire cable, the result are the same. Have tried to reset the device to factory default and reconfigure, but still unable to make it work properly.
Did more tests, observed:
1. on port 1, after power off and then power on the PAP2T, call to a wired line seems working at first call, but actually NOT: I can hear the ring tone on the phone I'm calling from, but the wired phone I'm calling to doesn't ring. So basically port 1 will not work at all.
2. on port 2, even after restart the PAP2T, call to wired phone will get line busy signal. But this port works fine to call mobile.
I haven't tested to receive call from the PAP2T: need to get a traditional number for the VOIP which cost money, as now already having calling problems, I'd like get existing issues fixed first.

Similar Messages

Problem with making CALLS using SIP on AS 5300

I have a setup where I have DSL users
connected and registered on SIPSP proxy
server, which is then connected to AS5300
My Problem is I am only able to make one
call. I am not able to make simultaneous
calls from the user agent. Pls. help me out.I have also attached the router running configs and SIPSP Proxy , traces.

You might try looking/posting here.
Microsoft Support – Office for Mac
Microsoft Support – Office for Mac (2)

Problems with a call transaction

Hi, I'm having some problems with a call transaction and I cannot understand why. I put A in the mode, and I am seeing the dynpros and I am pressing enter it works perfectly but when I use mode N it tells me that there is not information for one of the dynpros and it doesn't work. Does anybody know the problem and how to solve it??
Thanks in advance

Hi,
First of all thank you very much for your time.
I am using FB05 and the problem is in dynpro SAPLKACB 0002, and it says that batch input data doesn't exist. Here is the code, maybe you can see what is happening
LOOP AT t_resumen WHERE belnr = t_batch-belnr AND
 ( contador = 3 OR contador = 4 or CONTADOR = 5 ).
 READ TABLE t_clave WITH KEY belnr = t_resumen-belnr.
 d_clave = t_clave-bschl.
 i = i + 1.
 CASE i.
 WHEN 1.
 PERFORM bdc_dynpro USING 'SAPMF05A' '0700'.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 PERFORM bdc_field USING 'RF05A-NEWBS' t_resumen-bschl.
 PERFORM bdc_field USING 'RF05A-NEWKO' t_resumen-hkont.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 PERFORM bdc_dynpro USING 'SAPMF05A' '0300'.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 j_wrbtr = t_resumen-wrbtr.
 REPLACE '.' WITH ',' INTO j_wrbtr.
 PERFORM bdc_field USING 'BSEG-WRBTR' j_wrbtr.
 PERFORM bdc_dynpro USING 'SAPLKACB' '0002'.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 WHEN t.
 PERFORM bdc_dynpro USING 'SAPMF05A' '0300'.
 PERFORM bdc_field USING 'RF05A-NEWBS' t_resumen-bschl.
 PERFORM bdc_field USING 'RF05A-NEWKO' t_resumen-hkont.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 j_hkont = t_resumen-hkont.
 j_clave = t_resumen-bschl.
 PERFORM bdc_dynpro USING 'SAPMF05A' '0300'.
 PERFORM bdc_field USING 'BDC_OKCODE' '=BU'.
 j_wrbtr = t_resumen-wrbtr.
 REPLACE '.' WITH ',' INTO j_wrbtr.
 PERFORM bdc_field USING 'BSEG-WRBTR' j_wrbtr.
 PERFORM bdc_dynpro USING 'SAPLKACB' '0002'.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 WHEN OTHERS.
 PERFORM bdc_dynpro USING 'SAPMF05A' '0300'.
 PERFORM bdc_field USING 'RF05A-NEWBS' t_resumen-bschl.
 PERFORM bdc_field USING 'RF05A-NEWKO' t_resumen-hkont.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 j_hkont = t_resumen-hkont.
 j_clave = t_resumen-bschl.
 PERFORM bdc_dynpro USING 'SAPMF05A' '0300'.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 j_wrbtr = t_resumen-wrbtr.
 REPLACE '.' WITH ',' INTO j_wrbtr.
 PERFORM bdc_field USING 'BSEG-WRBTR' j_wrbtr.
 PERFORM bdc_dynpro USING 'SAPLKACB' '0002'.
 PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
 ENDCASE.
 READ TABLE t_porcentajes WITH KEY gjahr = t_resumen-zzbad
 zzbtd = t_resumen-zzbtd.
 IF j_hkont = t_porcentajes-cfacpr.
 PERFORM bdc_field USING 'COBL-PRCTR' t_porcentajes-prctrfac.
 PERFORM bdc_field USING 'COBL-ZZBTD' t_resumen-zzbtd.
 PERFORM bdc_field USING 'COBL-ZZBAD' t_resumen-zzbad.
 ELSEIF t_resumen-hkont = t_porcentajes-cadmin.
 PERFORM bdc_field USING 'COBL-KOSTL' '20801'.
 ELSEIF t_resumen-hkont = t_porcentajes-creca.
 PERFORM bdc_field USING 'COBL-KOSTL' '20401'.
 ELSE.
 IF d_clave = 01 OR d_clave = 04 OR d_clave = 40 OR d_clave = 09.
 IF j_hkont >= 424001 AND j_hkont <= 424005.
 PERFORM bdc_field USING 'COBL-PRCTR' 'DUMMY'.
 ELSEIF j_hkont >= 424601 AND j_hkont <= 424605.
 IF j_clave = 40.
 PERFORM bdc_field USING 'COBL-PRCTR' 'DUMMY'.
 ENDIF.
 ENDIF.
 ELSEIF d_clave = 11 OR d_clave = 12 OR d_clave = 14 OR d_clave = 50.
 IF j_hkont >= 424001 AND j_hkont <= 424005.
 PERFORM bdc_field USING 'COBL-PRCTR' 'DUMMY'.
 ELSEIF j_hkont >= 424601 AND j_hkont <= 424605.
 IF j_clave = 50.
 PERFORM bdc_field USING 'COBL-PRCTR' 'DUMMY'.
 ENDIF.
 ENDIF.
 ENDIF.
*Fin modificacion marzo 2007.----
 PERFORM bdc_field USING 'COBL-ZZBTD' t_resumen-zzbtd.
 PERFORM bdc_field USING 'COBL-ZZBAD' t_resumen-zzbad.
 PERFORM bdc_field USING 'COBL-ZZBTT' t_resumen-zzbtt.
 PERFORM bdc_field USING 'COBL-ZZBTU' t_resumen-zzbtu.
 PERFORM bdc_field USING 'COBL-ZZBTS' t_resumen-zzbts.
 PERFORM bdc_field USING 'COBL-ZZBAG' t_resumen-zzbag.
 PERFORM bdc_field USING 'COBL-ZZBRE' t_resumen-zzbre.
 PERFORM bdc_field USING 'COBL-ZZBC8' t_resumen-zzbc8.
 PERFORM bdc_field USING 'COBL-ZZBC9' t_resumen-zzbc9.
 ENDIF.
 ENDLOOP.

Problem with making a database link.

Hello All
I got a problem with making a database link.
When I execute this query
CREATE PUBLIC DATABASE LINK DBNAME
CONNECT TO database IDENTIFIED BY name
USING 'DBNAME.europe.company.com';
I am using other names because its private information
But when I look at the table dba_db_links I see this
OWNER | DB_LINK | USERNAME |HOST
PUBLIC| DBNAME.europe.company.com| name| DBNAME.europe.company.com
So the DB_Link name is changed. And this causes a problem with my asp website. I get the fault message
ORA-02085: database link DBNAME.europe.company.com connects to DBNAME
Cause: a database link connected to a database with a different name. The connection is rejected.
The global_names = true and I prefer to keep it that way.
So does anyone knows what is wrong about my Query or how I can change the DB_Link name.
Thanks for the support,
Remco

Thanks for the help Mohit
But thats whats I was doing.
The query in the first post is the same as what you are posting.
But by an (for me) unknown reason the database converts DBNAME to DBNAME.europe.company.com

I have problems with outgoing call no audio, only works with speaker. I bought my iphone on december 2011.

I have problems with outgoing call no audio, only works with speaker. I bought my iphone on december 2011.

Had the same problem, no audio on incoming or outgoing calls and only could hear the conversation of the call if I put on speaker. It seemed to start after I did a recent IOS update this past month. I tried restart, reset and restore of my iPhone but nothing changed. It appears not to be a software issue but a hardware problem. I got my phone this past summer so it was still under warranty and got it replaced.

Problem with 5800, call processing is too slow.

i have a problem with rejecting calls and recieving as well as dialling. it takes to much time to process. when a caller calls me they hear the dial tone for about 5 seconds then i get the call on my phone.. when i use third party software for automatic rejecting calls, the caller hears the dialtone for like 10 seconds or more then it gets rejected which is really annoying. please help me. is there a solution for this? this is not the network problem coz my sim n rejecting calls on other phones work fine. AND ALSO wen someone calls me i get the call alert like after 10 seconds, its very slow!!

Make sure you have upgraded to 1.1.1 which fixes volume problems.
Note that it will NEVER be as loud as standard cell phones but it should improve the volume so you have no problem hearing it in the car.

Setting always changes by itself in my iPhone 5s, also every few calls I have to face a problem with a call without sound

Setting always changes by itself in my iPhone 5s, also every few calls I have to face a problem with a call without sound, battery becomes empty quickly

User troubleshooting steps as outlined in the manual are reset, restore, restore as new. Have you tried any of these?

Problems with dropped calls and no reception on Samsung Continuum

My mother and I both purchased a Samsung Continuum in late March 2011, and have experienced the same problems with the phone. The device drops at least 2-3 calls per day, often on the same conversation; we have not found that location or time of day makes a difference. The phone freezes up frequently, even if no apps are running in the background. We lose our 3G network reception frequently, and cannot access our texts, emails, or the internet. The screen saver kicks in even when we are actively dialing a number, or typing in a text message. The overall performance of the phone is also poor, and it is quite slow much of the time.
We have raised this issue several times with a representative at one of the Verizon stores, but he states that he can find no problem with the phone, and that these issues may not be covered under our insurance plan. None of my friends with non-Samsung phones are having the same problems with phone reception and performance. I am aggravated enough with these issues that I am considering reactivating my old Blackberry, which worked like a charm.
I am not upset that my phone has not been updated to Android 2.2. I just want the phone to perform as stated, and not fail at its primary function: making and receiving phone calls. I am not certain if these problems originate with the phone, Verizon, or Samsung, nor do I care. I just want to resolve these issues as soon as possible, or I will have to look at other alternatives.
Thank you.

If this doesn't work...now what??? I have a useless $400 plus piece of unreliable junk. My Motorola Razor was ions more reliable than this phone...very, very sad but true.
What carrier were you using with the Razor? AT&T? Same area?
Dave M.
MacOSG Founder/Ambassador  An Apple User Group  iTunes: MacOSG Podcast
Creator of 'Mac611 - Mobile Mac Support' (designed exclusively for an iPhone/iPod touch)

Problems with conference calls(adding and merging calls) after upgrade to ios 8.1.2 on iphone 5s

I am having weird problem intermittently with adding calls or merging them or swapping them. The issue happens 8 out of 10 times whenever I try to do a conference call. This issue came up after I upgraded to 8,1.2. Never experienced this in 8.1.1 or previous version.
Some of the scenarios that I have experienced is:
1. While on the call, when I try to add a new contact, it just doesn't dial the second number.
2. Sometimes the second number gets dialed, cannot merge the calls.
3. After talking to the second person, cannot go back to the first call.
I am very sure that this is not a carrier issue as it worked flawlessly before upgrade.
Anyone experienced this before? Any suggestions?

Thanks for the above infromation. I did a complete restore of my iphone through iTunes connecting it to my computer via cable. iOS8.1.3 was re-installed. I then added back my settings and data which were backed up prior to restoring the phone. I still have the same issue with conferencing and adding a third caller. When I hit the [+] box, the existing caller is not put on hold. The phone appears to be making a call but it is not dialing to the 3rd party. Shortly thereafter, the Merge icon appears but there is no active call to merge with. I have tried this several times using my wife's iPhone and our home phone to set up a 3-way call. I know it is not working because the 3rd phone (our home phone) does not ring. Is this a hardware problem? My wife's iPhone 6 works with no problem and was purchased the same time I purchased my iPhone 6. Probably time for a visit to the Apple Store unless there is another solution.
iPhone 6; iOS 8.1.3; Carrier: Verizon

SPA 112 PROBLEM WITH SIMULTANEOUS CALLS

HELLO,I HAVE A PROBLEM IN THE ATA SPA 112 ABOUT SIMLUTANEOUS CALLS. The ata has 2 lines,when a call falls in line 1, the call on line 2 falls at the same time...and when I'm on line 1 and I recevive a call on line 2 the call in line 1 becomes mute and then drops.I didn' have these problems with the old pap2t .
Can you please help me to solve this problem ? Do I have to change something in the configuration ? Thanks,Mario

Hi,
thanks for responding.
I had found out about the timing problem in the meantime, but did not find a way to mark this thread as solved.
There are two timing values: one is the PSTN answer delay, and the other one the PSTN ring timeout.
It seems that ring timeout should be longer than ring time + ring pause. As long as this conndition is not met. the dial plan is not even considered

Intermittent problem with TestStand calling CVI DLL calling MSCV DLL

Sorry about cross post, but I am not sure which group is best to address
this issue.
Setup:
Windows 2000 SP1
TestStand 2.01f
CVI 6.0
MSVC++ 6.0 SP5
Problem:
I have a CVI Test Library DLL that contains test functions called by
TestStand using the C/CVI adapter. The CVI Test Library DLL in turn makes
several calls to another DLL written in MSVC++. I am experiencing an
intermittent problem with one of the MSVC functions. The problem ~appears~
to be stack related, but I am not sure. Among other things, this MSVC
function accepts a const char * argument that is a TestStand lookup string.
The function uses this string to access the TestStand API.
What happens is this: Everything works fine. I then recompile the CVI DLL
after making some mod, then run. The MSVC++ DLL asserts that the const char
* arg passed by the CVI DLL is NULL. However, this is not the case if I
single step through the CVI code. It has happened both with passing
variables as the const char * argument and as hardcoded strings literals, so
its not that I am actually passing NULL. The other argument to this
function is the TestStand sequence context dispatch pointer (LPDISPATCH
pobjSequenceContextDisp) and it always ~appears~ to be passed correctly.
The problem is frustrating and hard to debug because I can not
deterministically reproduce it. The problem ~never~ appears when I debug my
MSVC++ DLL in Visual Studio. And it only occasionally appears otherwise.
The problem, when it appears, always appears on the first run after
recompiling the CVI DLL, though the problem does not happen after ~every~
recompilation. I'd say it happens 1 in 6 times after a recompile.
Recompiling the exact same code does not always make the problem disappear.
If I change the CVI code (code that has nothing to do with the argument
itself though) and recompile the problem almost always goes away. Selecting
'Mark all for compilation' and rebuilding does not make the problem go away.
Only tweaking the CVI code and recompiling does (usually).
Whats more, the problem appears:
* With the CVI DLL built as Debug or Release mode.
* With the CVI default calling convention set to __stdcall or __cdecl.
* With the C/CVI TestStand adapter set to run in-process or external
instance of CVI.
The problem appears to be some sort of stack or argument passing problem
between CVI and MSVC, though thats just a guess based on the symptoms. I
have quadruple checked the calling conventions of all declared functions.
The CVI DLL functions all use TX_TEST (which resolves to __cdecl). The MSVC
DLL functions all explicitly use __stdcall. Is there a problem with calling
__stdcall MSVC functions from a __cdecl CVI function?
I can find no other memory leaks or indications of memory corruption
elsewhere in either the CVI or MSVC DLLs. Its only this one function that
exhibits this strange 'null const char *' problem.
Can anyone offer any ideas about what may be causing this problem? Anything
else I should check/verify?
Regards,
Joe

Silvius,
> Although I'm not sure if any of the following are the real cause of
> your problem, I have the following suggestions:
Thanks for the reply. At this point any and all suggestions are welcome...
> 1. There could be a problem with calling
> __stdcall MSVC functions from a __cdecl CVI function. As a workaround
> wrap the _cdecl call inside a _stdcall call that is exposed or
> exported to TestStand or vice-versa. This can be a problem because if
> _cdecl is used, the calling function is responsible for cleaning up
> the stack and if _stdcall is used, the called function is responsible
> for cleaning up the stack.
I was under the impression that as long as everything was explicitly and
consistently declared, you could safely mix cdecl and stdcall f
unction
calls. Is it bad to do this? Is this a known issue with the CVI compiler?
I've never seen a problem with doing this under MSVC++.
I'll try wrapping them in cdecl calls for CVI - though we have a
depressingly large number of stdcall functions in the MSVC DLL ;-). They
need to remain stdcall in the DLL because we also call them from Visual
Basic.
> 2.Don't mix Debug version of one DLL with the Release version of the
> other DLL. I had some bad experiences doing this and both DLLs where
> developed in MSVC. Allways use either Debug either Release versions of
> DLLs.
I verified that the MSVC DLLs were either ALL Debug or Release. I too have
seen nasty problems when MSVC Debug and Release is mixed.
One thing I had not thought of until your reply: What about mixing CVI Debug
DLLs with MSVC Release DLLs? Have you ever seen issues with doing this?
Thanks!
Joe

Firefox 6.0.2 keeps on crashing, problems with ajax calls

Hi,
I am using the jquery form plugin to make ajax calls on my sites, when i invoke the plugin and have Firebug open I get this message:
Could not convert JavaScript argument arg 0 [nsISupports.QueryInterface]
[Break On This Error] callback.data = aElem....getComputedStyle(callback.data, '');
rfhelper32.js
Firebug also tells me that it's limit has been reached 1571 entries shown.
Can someone tell me why this is happening; is there a problem with Firefox that will be fixed. It's not happening in IE9
Here is the information from a recent crash report (which may or not be related to the above problem!)
AdapterDeviceID: 0a66
AdapterVendorID: 10de
Add-ons: [email protected]:3.0.4,{6AC85730-7D0F-4de0-B3FA-21142DD85326}:2.5.5,{8f8fe09b-0bd3-4470-bc1b-8cad42b8203a}:0.17,{e968fc70-8f95-4ab9-9e79-304de2a71ee1}:0.7.3,{f36c6cd1-da73-491d-b290-8fc9115bfa55}:2.2.0,{BBDA0591-3099-440a-AA10-41764D9DB4DB}:3.1,[email protected]:1.8.2,{2D3F3651-74B9-4795-BDEC-6DA2F431CB62}:2011.7.1.3,{972ce4c6-7e08-4474-a285-3208198ce6fd}:6.0.2
AvailableVirtualMemory: 174600192
BuildID: 20110902133214
CrashTime: 1316093326
EMCheckCompatibility: true
Email: [email protected]
FramePoisonBase: 00000000f0de0000
FramePoisonSize: 65536
InstallTime: 1315406279
Notes: AdapterVendorID: 10de, AdapterDeviceID: 0a66, AdapterDriverVersion: 8.16.11.9104
D3D10 Layers? D3D10 Layers-
D3D9 Layers? D3D9 Layers-
WebGL? WebGL-
ProductName: Firefox
ReleaseChannel: release
SecondsSinceLastCrash: 160793
StartupTime: 1316067225
SystemMemoryUsePercentage: 86
Theme: classic/1.0
Throttleable: 1
TotalVirtualMemory: 2147352576
URL: https://s-static.ak.fbcdn.net/connect/xd_proxy.php?version=3#cb=f1ae6be54ac01b4&origin=https%3A%2F%2Fwww.paypal-business.co.uk%2Ffd558408b2cb6c&relation=parent.parent&transport=postmessage&type=resize&height=20&ackData[id]=1&width=250
Vendor: Mozilla
Version: 6.0.2
Winsock_LSP: MSAFD Tcpip [TCP/IP] : 2 : 1 :
MSAFD Tcpip [UDP/IP] : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD Tcpip [RAW/IP] : 2 : 3 :
MSAFD Tcpip [TCP/IPv6] : 2 : 1 : %SystemRoot%\system32\mswsock.dll
MSAFD Tcpip [UDP/IPv6] : 2 : 2 :
MSAFD Tcpip [RAW/IPv6] : 2 : 3 : %SystemRoot%\system32\mswsock.dll
RSVP TCPv6 Service Provider : 2 : 1 :
RSVP TCP Service Provider : 2 : 1 : %SystemRoot%\system32\mswsock.dll
RSVP UDPv6 Service Provider : 2 : 2 :
RSVP UDP Service Provider : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip_{91C733AA-510D-41D3-B67A-4441103BAE50}] SEQPACKET 1 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip_{91C733AA-510D-41D3-B67A-4441103BAE50}] DATAGRAM 1 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip_{4A8E4D1C-24D8-40C3-BC41-D04B5D505F39}] SEQPACKET 5 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip_{4A8E4D1C-24D8-40C3-BC41-D04B5D505F39}] DATAGRAM 5 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip_{C8F77A1D-B3A2-4DE2-AE72-C377BBD10D9A}] SEQPACKET 7 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip_{C8F77A1D-B3A2-4DE2-AE72-C377BBD10D9A}] DATAGRAM 7 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{C8F77A1D-B3A2-4DE2-AE72-C377BBD10D9A}] SEQPACKET 8 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{C8F77A1D-B3A2-4DE2-AE72-C377BBD10D9A}] DATAGRAM 8 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{4A8E4D1C-24D8-40C3-BC41-D04B5D505F39}] SEQPACKET 6 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{4A8E4D1C-24D8-40C3-BC41-D04B5D505F39}] DATAGRAM 6 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{3D95D40E-1835-44C6-A621-968094D90452}] SEQPACKET 10 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{3D95D40E-1835-44C6-A621-968094D90452}] DATAGRAM 10 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{D6AD3B6C-2F8E-49B4-BDCD-DB35518116E7}] SEQPACKET 9 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{D6AD3B6C-2F8E-49B4-BDCD-DB35518116E7}] DATAGRAM 9 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{18908ACF-76C1-4139-8C1C-89DF049156C5}] SEQPACKET 4 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{18908ACF-76C1-4139-8C1C-89DF049156C5}] DATAGRAM 4 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{4112C824-372C-4014-87AE-1BC13EA6E4CD}] SEQPACKET 3 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{4112C824-372C-4014-87AE-1BC13EA6E4CD}] DATAGRAM 3 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{2E408326-9611-4C41-B766-C4CB82734986}] SEQPACKET 0 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{2E408326-9611-4C41-B766-C4CB82734986}] DATAGRAM 0 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{91C733AA-510D-41D3-B67A-4441103BAE50}] SEQPACKET 2 : 2 : 5 :
MSAFD NetBIOS [\Device\NetBT_Tcpip6_{91C733AA-510D-41D3-B67A-4441103BAE50}] DATAGRAM 2 : 2 : 2 : %SystemRoot%\system32\mswsock.dll
VMCI sockets DGRAM : 0 : 2 :
VMCI sockets STREAM : 0 : 1 : C:\Program Files\VMware\VMware Workstation\vsocklib.dll
This report also contains technical information about the state of the application when it crashed.

Try the Firefox SafeMode to see how it works there. 
''A troubleshooting mode, which disables most Add-ons.'' 
''(If you're not using it, switch to the Default Theme.)''
* You can open the Firefox 4/5/6/7 SafeMode by holding the '''Shft''' key when you use the Firefox desktop or Start menu shortcut.
* Or use the Help menu item, click on '''Restart with Add-ons Disabled...''' while Firefox is running. 
''Don't select anything right now, just use "Continue in SafeMode."''
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shft key) to open it again.''
If it is good in the Firefox SafeMode, your problem is probably caused by an extension, and you need to figure out which one. 
http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes

Problem with multiple calls to hr_infotype_operation in a loop

Hi,
Im using infotyp 2003 with the following situation. For a date, e.g. 2011/07/20 and a person_nr I have several time entries, like 08:00-09:00, 10:00-12:00, 15:00-17:00. Now I read the entries with HR_READ_INFOTYPE and store them back unmodified with hr_infotype_operation in a loop in the same report.
data: i_p2003 type standard table of p2003.
CALL FUNCTION 'HR_READ_INFOTYPE'
 EXPORTING
* TCLAS = 'A'
 pernr = person_nr
 infty = '2003'
 BEGDA = '20110720'
 ENDDA = '20110720'
* BYPASS_BUFFER = ' '
* LEGACY_MODE = ' '
* IMPORTING
* SUBRC =
 tables
 infty_tab = i_p2003
 EXCEPTIONS
 INFTY_NOT_FOUND = 1
 OTHERS = 2.
loop at i_p2003 assigning .
CALL FUNCTION 'HR_INFOTYPE_OPERATION'
 EXPORTING
 infty = '2003'
 number = person_nr
 validityend = '20110720'
 validitybegin = '20110720'
 record = 
 operation = 'MOD'
 dialog_mode = '0'
 IMPORTING
 return = return_struct
 key = personaldatakey
 EXCEPTIONS
 OTHERS = 0.
endloop.
the first call to hr_infotype_operation succeeds but the following operations fail because of collision. This example is stupid, I know, but it shows the core of a problem I have in a more complex report.
I face the problem that several calls to HR_INFOTYPE_OPERATION cause a collision error even if there cannot be a collision because the data are unchanged.
Any hints on this.
Regards,
JOP

Hi, you must execute a 'BAPI_EMPLOYEE_ENQUEUE' before 'HR_INFOTYPE_OPERATION' and a 'HR_EMPLOYEE_DEQUEUE' after.
See next example:
Bloqueo del empleado
CALL FUNCTION 'BAPI_EMPLOYEE_ENQUEUE'
EXPORTING
 NUMBER = PERNR.
IF SY-SUBRC IS INITIAL.
Si se pudo bloquear el empleado intenta
insertar el infotipo
CALL FUNCTION 'HR_INFOTYPE_OPERATION'
EXPORTING
 INFTY = '2001'
 NUMBER = P0001-PERNR
 SUBTYPE = i_p2001-subty
 VALIDITYEND = acdate
 VALIDITYBEGIN = acdate
 RECORD = i_p2001
 RECORDNUMBER = '000'
 OPERATION = 'INS'
 TCLAS = 'A'
 DIALOG_MODE = '0'
 NOCOMMIT = ' '
IMPORTING
 RETURN = I_RETURN
 KEY = I_KEY.
IF SY-SUBRC IS INITIAL.
VARGT = 'Y'.
ELSE.
VARGT = 'N'.
ENDIF.
No se hace COMMIT debido que el estandar lo realiza
CALL FUNCTION 'BAPI_TRANSACTION_COMMIT'.
Desbloqueo del empleado
CALL FUNCTION 'HR_EMPLOYEE_DEQUEUE'
EXPORTING
NUMBER = PERNR.
Regards,
Diego.

Problem with OCI call and how to install and use 'DEBUG_EXTPROC' on Linux

Hi,
Can any one let me know how I can install and use this debug_extproc package. I have installed oracle XE server on Linux machine(32-bit).
When I use : DEBUG_EXTPROC.STARTUP_EXTPROC_AGENT' ... i get an error saying that : it is not declared.
I tried looking in all the directories but did not find the dbgextp.sql(which is required in order to install that package).And tried searching on google but could not get any relevant information.
Also I am newbie to OCI call interface and also to C programming too: I have coded a external procedure or custom user aggregate in C. But since I was using C++ : 'set' STL. I have compiled my program using g++ instead of gcc and I have correspondingly modified the make file in public/demo directory.
So, is it fine to do it that way: using OCI (instead of OCCI(C++)) but again compiling the pgm as a regular C++ using g++ instead of gcc.(But rest of the pgm including printf statements : everything is in C).
Also I have created the library from my : custagg.so library:
SQL> create or replace library custagg is '$ORACLE_HOME/lib/custagg.so'
But my aggregate function implemented as external C function using OCI is either not recognised or else : if recognized then there is some error because of which i am getting the following errors : ORA-06522
SQL> select MinDistance(TT) from egg1;
select MinDistance(TT) from egg1
ERROR at line 1:
ORA-06520: PL/SQL: Error loading external library
ORA-06522: /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/lib/custagg.so:
cannot dynamically load executable
Please kindly answers my queries and trying to resolve this for almost 4 days now and could not find any clue on how to get this done.
Thanks,
-NN

#/bin/make
# Make file for OCI,OCCI and ODBC demos
# Usage :
# For compiling & linking the cdemo81.c file
# make -f demo_xe.mk buildoci CDEMOEXE=cdemo81 CDEMOOBJS=cdemo81.o
.SUFFIXES: .o .c .cpp
ICINCHOME=$(ORACLE_HOME)/rdbms/public/
ICLIBHOME=$(ORACLE_HOME)/lib
ICLIBPATH=-L$(ICLIBHOME)
THREADLIBS=-lthread
CCLIB=$(ICLIBPATH) -lclntsh $(THREADLIBS)
OCCILIB=$(ICLIBPATH) -locci -lclntsh $(THREADLIBS)
CCINCLUDES = -I$(ICINCHOME)
CCFLAGS=$(CCINCLUDES) -D_REENTRANT -g -xs
LDFLAGS=
SO_EXT=.so
EXTLDFLAGS=$(LDFLAGS) -shared
REMOVE=rm -rf
MKLINK=ln
MAKE=make
MAKEFILE=demo_xe.mk
CDEMOEXE=custagg.so
CDEMOOBJS=custagg.o
OCCIDEMO=occidml
OCCIOBJDEMO=occiobj
OTT=$(ORACLE_HOME)/bin/ott
OCCIOTTUSR=hr
OCCIOTTPWD=hr
ODBCDEMOEXE=odbcdemo
ODBCDEMOOBJS=odbcdemo.o
AQDEMOEXE=ociaqdemo00
AQDEMOOBJS=ociaqdemo00.o
EXTDEMO=extdemo2.so
CC=/usr/bin/g++
echo "LIBCLNT value is :" $(LIBCLNT)
echo "CC value is :" $(CC)
.c.o:
g++ -c -I$(ICINCHOME) $(CCFLAGS) $<
all: clean buildoci
echo "LIBCLNT value is :" $(LIBCLNT)
buildoci: $(LIBCLNT) $(CDEMOOBJS)
g++ -o $(CDEMOEXE) $(LDFLAGS) $(CDEMOOBJS) $(CCLIB)
echo "CC value is :" $(CC)
echo "LIBCLNT value is :" $(LIBCLNT)
clean:
$(REMOVE) $(CDEMOOBJS) $(CDEMOEXE)
# This port-specific file is currently empty on Solaris. Product
# lines may use this file to override compiler definitions and
# flags used in occi.mk.
# Linux compiler definitions
CC=/usr/bin/gcc
cc=/usr/bin/gcc
CCFLAGS=$(CCINCLUDES) -DLINUX -D_GNU_SOURCE -D_REENTRANT -g
LDFLAGS=-g
# This macro CCINCLUDES has to be redefined on Linux because of
# the existence of the 'new' directory in t_work. The name new
# clashes with a system header file.
CCINCLUDES = -idirafter .
THREADLIBS=-lpthread
ifdef BUILD_CCC296
CC=/usr/bin/g++296
endif
And I am executing the make file using the command :
make -f demo12.mk buildoci CDEMOEXE=custagg.so CDEMOOBJS=custagg.o
I am not getting any error while running this make file.
Can you please tell me whether PLSQL/Oracle is able to locate the file or not. Incase, if it is locating the file but due to some error in the custagg.so it is throwing that error. If this is the case, is there any way that i can debug the C program .....how can i install the debug_extproc package.. I am really new to C & OCI ... if the custagg.so is being located then there might be some problem with the way I am dynamically allocating memory to some variables.
Please kindly reply to this Post/response.
Please let me know if you also want to see my program code.
Thanks & Regards,
-NN

PROBLEM WITH MAKING RECTANGLE

i have a problem with illustrator cs6.. before this i've tried cs5..but when i use cs6 i have a problem when making a rectangle..when i make rectangle let say 3cm x 3cm without border i mean stroke i got the exact size but then when i use border only i mean stroke only without feel with the same box the size change into 3.0555 not 3 cm anymore..so is there anything that i missed tick out in ai cs6? reply me asap...

Could be that "use preview bounds" is turned on in the preferences. Here is the same rectangle with that preference off (left), and on (right).
The rectangle was not changed in any way between these two screen shots; just the preference.

Problem with making call on my PAP2T

Similar Messages

Maybe you are looking for