Problem with memory card slot on nokia c5 03

Sir,
I have a Nokia C5 03 from the last 8 months.....
Working very well.
Recently, my memory card stopped working.
I thought that there might be a problem in the memory card and bought a new one.
Even though i inserted new card in my phone, i am getting the same error.
In file manager it is displaying as "Memory card Corrupted."
I have checked the new memory card by inserting in to another phone which was working normally.
There i have even formatted the new memory card and again inserted into my c5. 
Then also i am getting the same error message........
Can any one suggest me what to do in this regard??????
Thanks in ADVANCE.
Solved!
Go to Solution.

Hi,
Welcome to the forum!
Have you also tried inserting the old memory card to another phone as well? What happened after inserting it to another phone? If it's working properly with another phone, the memory card slot of the C5-03 might have an issue so you should bring it to the repair facility to have it checked. 
You can search for the nearest repair facility in your area from this link: http://www.nokia.com/in-en/care-point-finder/
Hope this helps.

Similar Messages

  • Has anyone had a problem with memory cards switching the file from EOS to EKS?

    My camera memory cards have suddenly switched from an EOS file to an EKS file and are no longer readable.  I don't know if the problem is my computer, my card reader, my memory cards, or my camera.  It doesn't seem probable that two cards would become corrupted or go bad at the same time.  I have two large capacity cards and two new high capacity cards that I haven't tried yet, but I'm afraid to try to use any of my other cards until I know what is going on with these two.   The camera I'm using a 5D Mark II.  Can anyone please help!   This is a serious problem for me! 
    Thank you to everyone for your help and assistance!
    Best regards,
    Windsails

    Lightroom should recognize your camera (assume it's LR3 or later) automatically without pointing it to the DCIM directory. The files you are referring to is system file I think and not the photos; thus OS cannot read the file.
    Do you have a card reader? For some reason, if you connect your camera into Lightroom directly, sometimes LR doesn't show the preview of your images. Instead you'll get ? next to a gray box. If you don't have a card reader, just plug your camera in, ignore the ? and the gray box (this is LR problem, not your camera), then import them anyway. You should see your test shot once it's done importing.
    Weekend Travelers Blog | Eastern Sierra Fall Color Guide

  • Problem with PCI Card Slot

    Is there a way to try to test this thing's PCI Slot?
    I have a Dazzle SmartMedia Card Adapter and it has stopped working. Nothing happens when inserted. I bought a 2nd card and trying to install it, the same thing. Nothing. So now, I'm trying to decide if its the card slot, the upgrade to 10.4.10 or Sophos Anti-Virus software.

    Hi, Marty. Your card slot's connection to the logic board may have loosened; that happens sometimes with Titanium Powerbooks, especially those that are handled and transported often. Flexing of the PB's case and frame is the cause. If that's your problem, it's very easy to remedy.
    Release your keyboard catches and gently tip the keyboard back over onto the wrist rests and trackpad, being careful not to jerk its ribbon cable. You needn't disconnect the cable. Beneath the normal positions of the X and D keys is a translucent plastic rectangular tab about 1" x 3/8". That tab is the card slot's connector to the logic board. Press down very firmly on it with two
    fingertips. If you feel or hear it shift even the smallest amount, it was probably a little loose, and is now properly seated again. Put the keyboard back in position and test the card slot. Let us know how you fare.

  • Problems with sd card slot

    I've only been using my SD slot for a week or so and it was working great. Today I inserted the card into the slot and it won't recognize it. I was being really careful and I made sure I ejected the card each time I used it. Is the slot shot or did something happen with the software? Any suggestions would be helpful.

    Did you find a resolution to your problem?
    I have a similar problem: Finder doesn't recognize my SD card in my reader. Yet, it is visible to Mail (Version 3.6 (936)) via the attachment listing. Which is the terrible work around I've been forced to use. I shut down to eject. I replaced the reader & it recognized it for a couple days, but out of the blue it choked again.

  • Problems with PC card slot

    I've just bought Motorola wireless notebook adapter (WN825G) for my 1st generation PB but when I insert it into the PC slot, nothing happens -- the PB won't recognize it. Does anyone have any advice how I can find out why and fix it?

    Unless you have information to the contrary, I am not aware of any MacOS driver support being available for the Motorola WN825G PC Card wireless adapter. Why did you choose to buy this particular card?
    If you are going to buy a non-Apple wireless network adapter, check with this list:
    http://home.earthlink.net/~metaphyzx/Wireless.htm
    or buy a known compatible card like one of these:
    http://www.macwireless.com/html/products/11g11bcards/11gPCCard.html
    http://www.sonnettech.com/product/aria_extreme.html

  • Hi, I have a Lenovo 3000 n100 that does not recognize the dvd player or SD memory card slot

    Hi, this is my first time on here so forgive me if I don't give all of the right information, I will try.  Until about a month ago my dvd player and SD memory card slot worked fine.  I was attempting to download pictures from the SD memory card to my laptop when for some reason it not only stopped reading the memory card but it erased it also.  I tried to watch a movie on it to see if it was working and it is not.  I checked the computer to see if I could manually turn it on and neither the memory card slot or the dvd player show up at all.  Is this a driver problem and if so how do I fix it.  Any help would be greatly appreciated.  Thanks, Linda

    I have struggled with the same thing, until about 1/2 hour ago....And its real simple.  I'm not a techy but here's what worked for me. 
    Since Lenovo doesn't send boot discs you are going to have to create one.  I went to http://www.ntfs.com/boot-disk.htm and downloaded the trial version - good for 10 days.  If this works for you then you should buy the software (that goes w/o saying).
    Once loaded to your machine you will need to create a DVD (CD may work as well, all I had was DVD's handy).  Just lauch the application and it will do this for you. 
    Then you need to insert the DVD/CD into your player and restart the machine.  
    Once lauched the Software will lauch the Active@ Boot Disk menu.  One of the options (going from memory here) was to give you a windows prompt.  I simply typed c: and took me to the C drive.  Then I typed chkdsk /f c:
    I was then told my c drive was locked (sounds familiar I bet) but this time I was given the option to dismount the volume which I did.  And it finally ran chkdsk, found and corrected all errors.  
    I rebooted my machine, launched diskeeper,  and guess what - I can finally defrag my harddrive now which is sorely overdue!
    Good luck.  I hope this works for you! 

  • USB ports and memory card slots not working

    My Pavilion a6120n desktop has worked brilliantly ever since I purchased it. As of last week the 2 usb ports in the front and the 2 unused usb ports in the back have stopped working. My printer is plugged into one rear port and my wireless mouse is plugged into a second rear port and these work fine.  I generally use a memory stick for data swapping or the card reader slots (which have also stopped working). I no longer see the memory card icons in the "Computer" window. When installing something new the "New Hardware Found" statement pops up but the driver install always fails. I think it is a software issue but there are no usb drivers to download on the HP/support site that I can find. . . so . . . Below is what I have tried so far.Run antivirus software. Full scan & memory scan - no issuesRun malewarebytes full scan - no issues I have tried restarting several times with no success. Restore to several previous restore points = failedRestarting computer in repair mode = failedRun the repair disk that I had made = failedChecked the power management for each usb port to see if the power was routed properly = okRemoved the case cover and carefully inspected the wiring and connectors.finally I tried uninstalling the usb drivers = failed  Upon restarting the computer the last time the startup file must have failed and after several hours of attempting a repair I had to reinstall the Window 7 completely. Still no usb or memory card function. Any help would be appreciated Thanks,MrBob38

    Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how the USB ports and memory card slots are not working, and I would be happy to assist you in this matter! Since you mentioned that you have already re-installed Windows 7 on your computer, and the USB ports still do not work, please contact our technical support for further assistance in this matter by clicking the link below to get the support number for your region.
    www.hp.com/contacthp/
    I hope this helps!
    Regards

  • HT1476 my iPhone 4 will no longer charge. It is also not recognised in iTunes. There seems to be a problem with the connector slot. I've tried other cables and other computers/plugs but the connection is not being made. Any suggestions?

    my iPhone 4 will no longer charge. It is also not recognised in iTunes. There seems to be a problem with the connector slot. I've tried other cables and other computers/plugs but the connection is not being made. Any suggestions?
    It seems to me that the connection port is faulty.
    George

    Looks like a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
    Be sure to make an appointment first...

  • Problems with Memory on upgrading

    Problems with Memory. I Dide not hace space to upgrade. Now i do, but It still cancels for lack of space

    Actually, your problem does not sound like memory, but hard drive space. By default, you lose 10% of your drive to the OS and formatting. To tell how much hard drive space you have go to:
    >Finder
    >At the bottom of finder in the gray bar it will tell you how much space you have available on your hard drive.
    Your hard drive should be no more than 85% full! If it is, delete, get a larger hard drive, remove items to an external drive.
    GarageBand only needs 1.2 MB of space.
    In order to use GarageBand, some additional content is required. If you do not already have the content installed, it must be downloaded.
    Make more disk space available by moving some of your files to a different disk (such as an external hard disk or a USB flash drive), or by deleting files you don't need and then emptying the Trash

  • Problem with RSC card on sun fire v490

    Hi all,
    I have a little problem.
    I got few v490 that were already used.
    When I connect to the management port of the RSC card I get the prompt of the RSC password, somthing i don't have.
    The OS doesn't get loaded and I can't do anything. ( if I had access to the OS I would have reseted the password)
    So now, I got left with the only option i thought of.
    1. Disconnect the RSC card,
    2. This will force the output of the consol to go to the serial port(tty).
    3. Jumpstart the machine (beacuse I don't even have the password for the machine)
    4. connect the RSC card, and reset the password.
    There is someone here that encountered this problem??
    Maybe there is a jumper that can reset the RSC password. i don't know... every response will be great!
    Thanks!!!

    Hi,How to set my link up in solaris 10 ?
    I dont know want happend to my machine solaris v440 it suddenly disconnected from n/w and finally i came to know that is a problem with NIC card..i din't find any light's glowing back side of the machine at NIC card.
    can any one help me in this pls how can i proceed furture for getting my NIC back?
    and i have excuted few commands
    #ndd -set /dev/ce instance 0
    #ndd -set /dev/ce adv_1000fdx_cap 1
    #ndd -set /dev/ce adv_autoneg_cap 0
    I have got dladm show-dev is
    ce0 link: unknown speed: 1000 Mbps duplex: full
    ce1 link: unknown speed: 0 Mbps duplex: unknown
    I dont understand that why my link is showing still unknown ...any help..

  • Problem with SD card reader

    I have problem with 4-in-1 card reader in my laptop.
    When I insert 64 MB microSD (with adapter of course) everything is working fine, but 1024 MB microSD isn't working. dmesg shows
    mmc0: unrecognised SCR structure version 1
    mmc0: error 4 whilst initialising SD card
    The card is allright, because in my friend's laptoptop it works fine.
    Can somebody help me?

    Hi
    I had a problem with my card reader also.
    When I run the command "groups" noticed my user wasn't in the avahi group.
    Ran :
    sudo gpasswd -a <myuser> avahi
    (substitute "<myuser>" by your user)
    Inserted the card again and.. voila, it worked!
    Greets
    Nuno lopes

  • Yoga 11s Problem with SD Card reader

    Hi.
    Just bought a Yoga s11 8/256gb with windows 8 64bit.
    When i put in the SDHC card (Is use in camera) in the SD card reader nothing happends..
    Tried to download drivers, but not sure if i got the correct one.

    Hi
    I had a problem with my card reader also.
    When I run the command "groups" noticed my user wasn't in the avahi group.
    Ran :
    sudo gpasswd -a <myuser> avahi
    (substitute "<myuser>" by your user)
    Inserted the card again and.. voila, it worked!
    Greets
    Nuno lopes

  • My phone is iphone 4 (GSM)-american type with IOS5.11 , i have problem with sim card failer (korek type)

    my phone is iphone 4 (GSM)-american type with IOS5.011 , i have problem with sim card failer (korek type)

    Sounds like your iPhone is locked to AT&T. Contact them to see
    if you qualify for unlocking.
    This link may provide some assistance:
    unlocking AT&T iPhones (thanks to wjosten for the link)
    http://www.att.com/esupport/article.jsp?sid=KB414532#fbid=Ont7guWFCdY

  • After update my memory card slot is not working

    after update my memory card slot is not workingplease help me 

    Hi!, SHAIKE: Welcome, to Forum !. For help you, is necessary what, indicate brand, model and Operating System of your device.

  • Mega Player 536 problems with SD Card

    Hello, can any one help me here, i got me MSI mega player 536 , but i can't play files from SD card. I tried 4. diferent types of SD card. Player register the card, but when i try to open files i got message: "No files fund". I found test of player on www.hw.no, and they write in the test that Player has problems with SD card.
    Any one?

    It's hardware problem with player, i'll get a new one. Then we have to conclude that Mega player 536 has not problems with SD card. Thank's to every one on this forum.

Maybe you are looking for