Problem With MuVo V200 after software upd

Hi
Today I buy a MuVo Gb,
I check that the software ver. in the MP3 player
was old.
I download the file "MuVoV200_PCFW_LF__2_03.exe"
and installede the file, No problem
After the update I can NOT turn-on the mp3 player,
and the pc can NOT see the MP3 in the USB port.
So it is DEAD. Have can i wake-up the mp3 player ? again
Regard
Arne

From the website, download and install the Mass Storage Drivers.
Then, press and hold the Play button while connecting your player to the USB port of your PC. This is connecting your V200 in what is called Recovery Mode.
Keep pressing the Play button until the New Hardware Wizard starts.
Complete the wizard.
When finished reload the firmware. If it doesn't work with the latest version then try one of the earlier version linked to in the thread in my signature line.
PB

Similar Messages

  • A Problem With Muvo V200 !!

    Hi everybody, I've bought a Muvo V200 GB, and it works well , less one thing:
    When the blue light is activated I feel a very "high-pitched" sound, and it's very unpleasant.
    Can somebody tell me if there is a firmware that fix that problem ?
    I've tried to format the usb flash but I still have this problem. And I've also seen some posts in other forums that complain about that.

    No, the problem is with the V200 hardware itself, not the headphones. But using a higher impedance phone results in this high frequency noise being greatly attenuated. Being a hardware issue, there is no possible firmware fix for this. The only option is to go to a higher impedance phone (the Koss KSC-75 sounds great and is available for $5 from amazon.com) or li've with the problem. You can of course set the player to have the backlight always off - this will also eliminate the problem except at startup but will make adjustments more difficult in the dark.

  • Problems with Storm 9530 after software update

    Greetings, I am new to this forum and hope I am in the right place.
    After an email prompt from BlackBerry, Yesterday, I updated my software on my Verizon BlackBerry Storm, 9530.
    Now I have several problems;
    1.  Voice commands are not being recognized as easily as previously, making hands free calling almost impossible.
    2.  Pandora will stall near the end of each selection.  The song will resume after I push the pause and then the play button.
    3.  When I attempt to live stream from a local radio station, I get the following message: "! This playlist contains no valid songs"    Buffering... is displayed in the upper right hand corner, but no connection is ever made.
    Any ideas what I need to do to fix the thing?

    Hi and Welcome to the Forums!
    1) A known bug...we all hope that RIM is working on a fix.
    2) A known bug...Pandora is working on a fix. I have heard that it is available on their website but not yet via AppWorld.
    3) Very difficult to diagnose...it could be the website itself...it could be your device browser settings....it could be a number of things. Try these steps.
    Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
    Register with VZW:
    Dial *228, select option 1
    Dial *228, select option 2
    Register HRT:
    Homescreen > Options > Advanced Options > Host Routing Table > BBKey (it does not matter which line is current) > Register Now
    Resend Service Books:
    KB02830 Send the service books for the BlackBerry Internet Service
    Websites can be coded to perform better with some browsers rather than others. The BB Browser can appear to websites as several different things...that setting is, from within the Browser App, (BBKey > Options > Browser Configuration > Browser Identification). Changing that to another browser might help your BB interact better with some websites. In combination with all of the other configuration settings, you need to find the combination of all of these settings that works best for the sites you are visiting. Sadly, there is no "best advice" to give as each persons needs are different. But, I typically find that changing the Browser Identification often helps -- most often by changing to FF or IE (if those are available to you...the options vary by carrier).
    Hopefully something in there will get you going again.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Sound problems with audigy platinum after software upgra

    After updating software (and then deleteing and redownloading) I had the usual sounds from windows but no sound in other programs. The eax environment was turned to no effects. When I added effects there was then sound. This would be OK in games but is annoying when listening to news broadcasts on AOL.
    Any ideas?

    Well now I'm confused alright. I told you I took out the TV tuner and everything seemed fine. Wrong! The system froze again while playing a DVD movie this time. Naturally I thought about the graphics card which is an Albatron FX 5200 (yes one of those about which NVidia appologised for their technical problems). So I opened the case and took the graphics card out and it was hot! I mean you could fry eggs on it. I checked the system's temperature and I got 58 degrees Celsius for the mainboard. I forgot to mention that I live in Greece and the atmosphere's temperature now is between 29 and 35 degrees celsius. Then I rememberd reading that the new FX series by NVidia are considered very bad graphics cards and besides everything they have cooling problems. So I stuck in my old graphics card (ASUS GEforce Ti 4200) and mounted an additional cooler fan on the case. Now the mainboard's temp doesn't rise over 49-50 degrees Celsius and until this time I haven't had any freezes. My guess is it wasn't the tuner after all. It was a temperature problem and since I'm working with programs that stress the CPU and Audigy to their limits (multiple music sequencing and audio mixing software) I have a good reason to believe that. So the FX 5200 is most likely to have caused it all. Needless to say that besides the extreme temperature the card has crappy performance as well no matter the 128 MB of RAM. I just hope I won't need any more fans to be able to work.

  • Problems with monitor/resolution after software update

    I installed the latest security update tonight, and now my monitor no longer properly works with my mini. I have a Dell 2005FPW. I was using 1680x1050 resolution with no problems. When I rebooted after the update, I noticed my resolution had been changed... and now the mac only detects my display as a "VGA display" and I can't select that resolution any more! The monitor still works fine with my PC.
    How can I get my 1680x1050 back??
    Mac Mini   Mac OS X (10.4.5)  

    Do you have a KVM switch to share your monitor between your Mac and your PC? I was getting this problem when I got one of these so my new Mac could share my monitor etc with my old one but found a way round it. In System Preferences -> Displays, tick the 'Show displays in menu bar' box. Then click on 'Detect displays' from the drop down menu. The screen will go blue for a moment and the computer will recognise the monitor for what it is.
    Mac Mini 1.4GHz G4, PowerMac 450MHz G4, both   Mac OS X (10.4.6)   Airport Express

  • Problem with iphone4 music after software update

    Updated software on my iphone 4 on 3/22/13.  Now, my entire music library on my phone is in icloud format and must be downloaded.  Discovered this while flying cross country. Grrrr. 
    Why did this happen and - more to the point - how can i get my music library to sync normally again so it's simply on my phone and ready to play?
    Thanks.

    I phoned my provider as requested and they have advised me that it is necessary to send my brand new phone in for repair.  I honestly don't know if they have opened a support ticket.  I do thank you for your prompt assistance thus far, however, I am none too impressed with this situation.  I hope the next software update doesn't cause more problems, so far the phone isn't worh the contract it's written for when it comes to user friendliness, app availability, or user options.  I was hoping for better from BlackBerry this time around. 

  • Problems with LG Enact after software update to KitKat

    After the update, I seem to have
    1) Battery charging issues. Problems charging past 96% (or at least appears that way on the notifications bar on my phone). Have had to unplug and/or restart phone to complete the charge and sometimes it doesn't always work.
    2) Slower 4G speeds. Often going down to 3G or 1X
    3) Phone seems sluggish overall going from app to app and also when typing on the keyboard
    4) Freezing when using wifi or phone data plan.
    I've googled these problems and appears that other phones have been having one or more of these issues as well. Any ideas on how to fix these issues?

    If you've googled, then you likely have seen some of the suggested "fixes".  Have you tried:
    1) Check your network settings - be sure it'[s set to LTE/CDMA - I've noticed that updates and resets on my phones tend to revert to Global which results in glitchy behavior, at least for me.  Resetting to LTE/CDMA and restarting helps.
    2) Run a system cache clear, it won't affect any of your data or setting but WILL clear up unused fuiles and processes that may be slowing things down and causing the sluggishness you see. 
    Performing a wipe cache partition removes any temporary files that may be causing an issue with the device. All personal files and settings are not affected by this option.
    Power the device off.
    Press and hold the Volume Up and Down button then press the Power button.
    When presented with the Boot Mode Selection Menu, release all buttons.
    Press Volume Down button to select 'Recovery' then press the Volume Up button.
    From the Droid triage screen:
    Press and hold the Volume down button.
    Press and release the Volume up button.
    Release the Volume down button.
    Select wipe cache partition then press the Power button.
    Use Volume keys to navigate options.
    Select reboot system now then press the Power button.
    Use Volume keys to navigate options. 
    3) FDR - Factory Data Reset - be sure all your contacts, photos, etc are backed up - if you use Google to store contacts and auto back up photos and music it should already be backed up.  Once you do the reset, restore from Google, and selectively reinstall your apps.  This is a last resort, but it can clear out a lot of accumulated gunk.
    Hope this helps.

  • I have a problem with my iphone,after upgrade software ios 6.0.1,  is not possible to use the wi-fi, used until now, because is not possible to have the login, i find this message " the requested URL  was not found

    I have a problem with my iphone,after upgrade software ios 6.0.1,  is not possible to use the wi-fi, used until now, because is not possible to have the login, i find this message " the requested URL  was not found

    You have to go to autherized iPhone agent.

  • Problems with ITMS Videos after 1.1 Update

    OK, so there are lots of posts about video problems on 5G ipods after software update 1.1 and what encoding methods were used etc etc.
    After updating my 60GB iPod to 1.1 all my videos, including those purchased from the iTunes Music Store, suffer from audio problems.
    The video playback is fine, no freezing like others have mentioned, but I get loud popping and clicking sounds on the audio, particulalry at the start of a clip.
    Has ayone else experienced problems with video sound after the 1.1 update?
    Restoring to software 1.0 resolved the problem so there is definitely a problem with 1.1 and ITMS content.
    Apple need to sort this out. Fast.

    I foolishly did the 1.1 upgrade to my 60G iPod. I found that, as we all know by now, that all ov my videos that weren't from Quicktime Pro or purchased through iTunes hang after about 30 seconds, and then continues without any audio. But, the really obnoxious part is that my videos that I converted via QuickTime Pro suffered from very strange audio artifacts. These would fall into the category of clicks, purrs, warbles and other strange noises in addition to the audio that is supposed to be there. That pushed me over the line, and I "downgraded" my iPod back to release 1.0. I did the "restore" to completely erase my iPod and then re-loaded it from iTunes. I had already upgraded iTunes, and it has no problems with my now-restored-to-version 1.0 iPod. By the way, you have to edit a system file in order to do the downgrade: Put the ipod in harddisk mode. Edit the file (hidden folder and file) \iPod_Control\Device\SysInfo Replace the line that have the word "buildID" with this line:
    buildID: 0x05908000 (6.0)
    Then run the original iPod Updater to put 1.0 back onto it. This will leave you with the "feature" that any video that you change the Video Kind to TV Show will not show up on your iPod unless it's in a Video Play List. I actually like this, as it keeps the Video list from being cluttered up.
    Sony Vaio PCG-U1   Windows XP Pro  

  • Dear i have a problem with the fingerprint after updating to ios 7.1 when plugged in electricity works like a charm

    dear sirs.
    i am an apple customer since first iphone but right now i am having problems with fingerprint sensor after updating to ios 7.1.
    when plugged to electricity it works but when unplugged sometimes work.
    please solve this issue by a quick update and thanks.

    I have been on the phone twice today with my carrier. They reset it the first time, it worked for an hour then messed up again. They reset it a SECOND time.. It worked for 6 hours, then messed up again. I don't know if this is a software issue or what but if ANYONE has any insight, I would appreciate it greatly.

  • Reception / Battery problems with iPhone 3GS after upgrading to iOS 4.2.1

    There are major reception and battery problems with iPhone 3GS after upgrading to iOS 4.2.1.
    I can not believe that Apple did not test this for major bugs like this one is.
    I am a business user and can not effort to have bad reception. Apple wants to gain in the business clients... I never had this with my former BlackBerrys!
    I need a reliable phone not a play thing like this is right now, it just needs it to work propely. And if a major bug like this comes along, fix it immediately. After the iPhone4 story, now this...incredible! Going back to my reliable BlackBerry! It just ain't reliable and takes forever to fix a problem.

    I have the same issue after iOS 4.2.1 update. I am using iPhone 3GS officially unlocked by Apple. I tried using different SIM cards and both carriers show same problem when using phone in 3G mode. Phone falls back to EDGE mode showing 'E' from '3G' at start. I have reset the phone and rebooted several times and moved to different cell areas in the city just to verify the problem.
    I had no such issues earlier. I also have Nokia E71 which shows full signal and has no such issues.
    I have posted the bug on apple iphone feedback page. I hope they Apple will fix the problem and test the release properly on all models before releasing to public.

  • Problem with the workbook after upgrade

    Hi all,
    We are facing some problems with the workbooks after BW 3.5 Upgrade.e.g. some templates are disturbed, some variables have been affected. So I have few doubts --
    1. What could be the possible reason behind this?
    2. What exactly got changed in the system which reflected this problems?
    3. What other problems might have occurred which we may not have noticed?
    4. How can I find out the number of workbooks affected due to this?

    Dear ,
    This is known issue:
    Please implement the below mentioned note as this will solve your issue,
    Note 1609237 :  Subsequent correction to 1567679
    Regards,
    Arvind

  • Problem with iWeb 09, after the publication in a local file.

    *Subject: problem with iWeb 09, after the publication in a local file, i can't see my blog, nor my photos, but before that all was working fine.*
    After the publication in the local file, I see all my pages, but there is a mistake on the page "Blog" where I just can see the top of my page, it's cut and I can't see it entirely, so I can't see the inputs while I should see 3 news or 3 inputs. And it's the same for the "Photos" page where the page is cut, I can't see the photos, and it's just written : "Put the slide show and subscribe".To finish, when I want to activate the comments, it doesn't work neither.
    Please help me.

    I want to activate the comments, it doesn't work neither.
    The comments feature is only available when you publish to the MobileMe server, so I don't think you can use it when you publish to a local file.

  • Has anyone had a problem with CS3 crashing after downloading OS 10.8.1 on a imac?

    Has anyone had a problem with CS3 crashing after downloading OS 10.8.1 on a imac? 

    Peggy
    You are probably correct. I tried all different variations to test it. As long as I quit each document separately, i.e., red dot it, I seem to bring up only one document after that whether I click on the document itself or open it within pages. The same is true with numbers.
    Two more questions:
    1) can you turn off the "resume" feature? If so, how? I could not find a way to do it.
    2) why the "save a version" feature in pages? What happened to the old "save" and "save as" features?
    Thanks so much, you saved me a lot of frustration but I am still going to install MS Office for Mac.
    Daveben

  • Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)

    Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)
    I re set up my Airport network , having had 4 expresses for years doing a good job. I bought another and an express, but then a time capsule after my external drive died. .Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)
    I moved house and have fibre network so 38mb/s - they all look ok on the utility, but its not till I saw the App version that they are not compatible as mac will not upgrade the version 6 ones, leaving me with 2 disjointed networks and 7 appliances, 4 of the old , 3 of the new.
    my new house is expansive so i wanted the extended range and airplay in each room.
    This is not told to customers, and utility doesnt show any issues.
    I do not seem to get any range from either network now, - and I'm quite experienced with airport (6 yrs of setting up & using & extending)
    Any advice ?
    LJx
    Message was edited by: LJLDN
    Message was edited by: LJLDN

    Sorry couldn't change the detonations to Airport and am new so cant delete!

Maybe you are looking for