Problem with my 875P NEO FIS2R when tyring to use x4 Crucial 512MB DDR modules

Hi all
I have a problem with my 875P NEO FIS2R when tyring to use x4 512MB DDR modules. At first the system seem fine then it just hangs on me. All modules are exactly same and I have tried updating my bios and adjusting the settings but nothing works. My system is fine when using x2 512MB moduels. I have searched the forum and found no clear answer although there are other people with this problem. Please can anyone let me know if there is anything I can do with my current configuration to make the x4 512MB DDR work?
From other posts I have learned so far that I either have to buy Paired modules from the manufacturer (which is no use because I bought my first x2 DDR a year ago) or only use x2 and now Dabs isnt taking the other x2 that I just bought because there is nothing wrong with the modules themselves (its the mobo).
I built my system from scratch and wouldnt have been able to have done it without previous assistance so thanks in advance for any help

Relaxing the timings will enable your RAMs to run at higher latencies so that they do not need to go extra mile to catch up with the transfer rates with the FSB.
Lowering the frequencies is like underclocking a speedy twin turbo to a standard single turbine which means lowering of speed so that the RAMs can run lower than expectations which'll be able to provide room for o/c'ing back near to its original frequency.

Similar Messages

  • Probems with msi 875p neo Fis2r and network controller driver

    Hi guys just wondering if anyone could help me with my msi 875p neo FIS2R and problems with the network controller driver/network card.
    I'm running xp on a computer my nextdoor neighbour gave me. I got it working fine  with service pack 3 installed but then installed a bunch of windows updates last night and the computer would switch itself off before windows could start. Now I reinstalled xp and unfortunately it does not recognise the network controller/card at all now. I tried installing the intel network controller drivers but it stopped because it said no intel adapter/card was installed/present. Could anyone please help with suggestions? I tried running everest and under newtwork it doesnt list intel network adapters but I'm pretty certain it is. Again any suggestions?
    --------[ EVEREST Home Edition (c) 2003-2005 Lavalys, Inc. ]
        Computer:
          Operating System                                  Microsoft Windows XP Professional
          OS Service Pack                                   Service Pack 3
          DirectX                                           4.09.00.0904 (DirectX 9.0c)
        Motherboard:
          CPU Type                                          Intel Pentium 4, 2800 MHz (14 x 200)
          Motherboard Name                                  MSI 875P Neo-FIS2R (MS-6758)  (5 PCI, 1 AGP, 4 DDR DIMM, Audio, Gigabit LAN, IEEE-1394)
          Motherboard Chipset                               Intel Canterwood i875P
          System Memory                                     1024 MB  (PC3200 DDR SDRAM)
          BIOS Type                                         AMI (10/11/04)
        Partitions:
          C: (NTFS)                                         238464 MB (200326 MB free)
    --------[ DMI ]---------------------------------------------------------------------------------------------------------
      [ BIOS ]
        BIOS Properties:
          Vendor                                            American Megatrends Inc.
          Version                                           V2.4
          Release Date                                      10/11/2004
          Size                                              512 KB
          Boot Devices                                      Floppy Disk, Hard Disk, CD-ROM, ATAPI ZIP, LS-120
          Capabilities                                      Flash BIOS, Shadow BIOS, Selectable Boot, EDD, BBS
          Supported Standards                               DMI, APM, ACPI, ESCD, PnP
          Expansion Capabilities                            ISA, PCI, AGP, USB
      [ System ]
        System Properties:
          Manufacturer                                      MICRO-STAR INC.
          Product                                           MS-6758
          Version                                           00C
          Serial Number                                     00000000
          Wake-Up Type                                      Modem Ring
      [ Motherboard ]
        Motherboard Properties:
          Manufacturer                                      MICRO-STAR INC.
          Product                                           MS-6758
          Version                                           00C
          Serial Number                                     00000000
      [ Processors / Intel(R) Pentium(R) 4 Processor ]
        Processor Properties:
          Manufacturer                                      Intel
          Version                                           Intel(R) Pentium(R) 4 Processor
          External Clock                                    200 MHz
          Maximum Clock                                     4000 MHz
          Current Clock                                     2800 MHz
          Type                                              Central Processor
          Voltage                                           3.3 V, 2.9 V
          Status                                            Enabled
          Socket Designation                                FC-478
        Network adapters:
          Direct Parallel                                   5.1.2535.0
          WAN Miniport (IP)                                 5.1.2535.0
          WAN Miniport (IP) - Packet Scheduler Miniport     5.1.2535.0
          WAN Miniport (L2TP)                               5.1.2535.0
          WAN Miniport (PPPOE)                              5.1.2535.0
          WAN Miniport (PPTP)                               5.1.2535.0
     

    Quote from: Jack t.N. on 14-November-09, 08:00:05
    Clear CMOS with your PSU unplugged from A/C power.  Then load "Optimized Defaults" in BIOS and retest.
    thanks jimi... jack
    will try that and post later if it worked... ive never cleared cmos, this sort of thing is relatively new to me but thanks again

  • How to disable AGP Fast Write with MSI 875P Neo-FIS2R ??

    How can I disable AGP Fast Write with the MSI 875P Neo-FIS2R ? I can't find an option for this in the BIOS !

    You wont usually find this option in most MB BIOSES , as the only Option that SOME BIOSES Have is the Option to enable, disable SBA (Side Band Addressing) for the AGP Bus....In order for you to Disable or Enable the FW, You Must have the Option in your Vidio Drivers Controll Panel.....If you have a NVIDIA Card, you Must go to  http://www.guru3d.com  And Download the program "NVHardpage" and then Open the Program and you wil have the Choice to Enable these options and they will then appear in your Vidio driver CP >> "Activate "Coolbitts" (this is NVIDIAS Overclocking Utility) Activate "Harware Options", and then Activate "AGP Options" and finally Activate "Performance Options"........If you have a ATI Card then you must Download one of thier "Tweeking Utilities".......I will Post the Direct "Link" for NVHardpage in a Minute, just say yes to the Lic. Agree. and download......Here>> http://download.guru3d.com/nvhardpage/  ...........Sean REILLY875

  • Problem with MSI K8T NEO-FIS2R

    When I boot my computer I get a message invalid boot.ini then it says c:\windows and windows starts normaly. What I don't understand is why do I get invalid boot.ini Anyone knos how to fix this?

    I'm sorry for no specs. Here you go
    MSI K8T NEO-FIS2R
    AMD 64 3000+
    2X 512MB 400MHz Ceon CL=2,5
    HDD 120GB WD
    HDD 4GB SEAGATE
    CDR DVD-RW NEC ND3520
    CDR SONY
    400W POWER SUPLY
    primary master CDR DVD-RW
    primary slave NONE
    secondary master CDR SONY
    secondary slave HDD 4GB
    and last HDD 120GB on primary raid
    NONE on secondary
    I have ORIGINAL windows xp with sp2 on 120GB HDD. I bought this computer and they put windows xp on my system.

  • Problem with closing other firefox windows when window in use has more than 1 tab open

    If I have multiple firefox windows open, and the one that I am using has more than one tab open, when I try to close one of the windows that I am not using by hovering over the firefox icon on the taskbar, then clicking the cross on the other windows, a message appears asking me if I want to close a window with more than one tab open. This means that firefox is trying to close the window that I'm using, not the one I'm trying to close. Please note this only happens when I hover over the icon on the taskbar then click the cross for the window I want to close. If I open the window properly, then click the cross on the window itself, it works fine.
    Just wanted to know if anyone else has this problem, and if they do, then mozilla should probably fix it in their next update, it's getting really annoying now

    I can't find a bug on file for this on https://bugzilla.mozilla.org/ (although there are many taskbar-related issues under review).
    (1) Just to confirm, do you both have "Show tab previews in the Windows taskbar" turned off here:
    orange Firefox button (or Tools menu) > Options > Tabs
    (2) Have you tried disabling Firefox use of hardware graphics acceleration?
    You usually need to restart Firefox in order for this to take effect, so save all work first (e.g., mail you are composing, online documents you're editing, etc.).
    orange Firefox button (or Tools menu) > Options > Advanced
    On the "General" mini-tab, uncheck the box for "Use hardware acceleration when available"
    If you restart Firefox, do you notice any changes?

  • Problem with iTunes installation - Error Message when trying to use

    I intalled iTunes on my Dell Laptop. The icon is on my Desktop, but when I try to start it, I get the following error message;
    "iTunes has encountered a problem and needs to close. We are sorry for the inconvenience."
    Then the error message wants me to send some message to microsoft?

    You can't do that.  Instead, just remove "aaa new-model" from the config then try to deploy it.  Alternatively, you can try "merge mode," but that will send the whole config back to the device.

  • Having problems with phone getting too hot when not in use

    Hi there -- I'm trying to figure out what I can do to fix this.  Recently I had to get a replacement S3 because my original shut off mid-use and wouldn't turn back on.  The replacement has been here for about a month and in the last 2 weeks I'm having issues with it getting too hot.  The first time it happened, I had it plugged into the stock charger for about 1 1/2 hours - and I had picked it up expecting it to be fully charged but it was extremely hot and had a warning on the main screen saying that the battery was critically hot and was not charging and the phone was nearly completely dead.  I unplugged it, took the battery out and let the main phone body cool down.  After about 15 minutes, the body felt like room temperature again, so I put it all back together.  It turned on, charged normally that night and all was well. 
    Now for the last several days, I'm having issues again with it getting hot at random times when I'm not even using it (and not charging it).  The last time, I downloaded a temperature app and it said the phone was nearly 105 degrees, and it felt the hottest right at the home button.  Later that night after it cooled down, I noticed that the battery wasn't charging at all and was depleting rapidly on the charger.  I restarted twice with no change and then took the battery out and let it sit for several minutes.  After that it began charging again. 
    With it getting hot so much more often now, I'm starting to worry about this happening when I need my phone for an emergency as I spend a lot of time on the road transporting my kids to school and activities.  Is there a fix for this?  It doesn't appear to be the battery because my husband and I have the same phone and I've already swapped batteries with him - same issue for me, no issue for him.  Please help?  Thanks!

        Hello Micheliu813, let's get to the bottom of this together! Are you using the same charger that came with the phone or a 3rd party charger? We can also test the phone in safe mode to see if the device heats up again. Check here for steps: http://vz.to/1kb9LUM
    WiltonA_VZW
    VZW Support
    Follow us on twitter @VZWSupport

  • [875P Neo Series] 875P NEO FIS2R - Bootup delay with disk attached to Promise RAID

    Hi,
    I have a problem with my 875P NEO FIS2R mobo. I just added a 400GB SATA RAID-0 array to the Promise controller and now I get a 50 second bootup delay after the BIOS has run through everything and beeped and before the first WinXP splash screen.
    I boot up from a 160GB SATA RAID-0 array on the intel ICH5R controller. Both arrays work fine from within Windows. I have two DVD drives on the ICH5R PATA connection but nothing else on the Promise.
    If I disable the Promise controller in BIOS the delay goes away.
    I have tried disabling SMART, turning off the quick-boot option with no effect.
    When I first installed my system I tested performance with booting from a single SATA drive on ICH5R vs Promise and I noticed the same issue, but didn't care then because I only needed one disk so I just kept Promise disabled in BIOS.
    Any ideas how I can get around this?
    Regards,
    Jonathan

    Sorry I have been a away for a few days.
    Details requested...
    Quote from: redeyedog on 21-June-05, 05:50:27
    If the Promise controller was out of the picture (Disabled), and you have the SCSI adaptor and its devices setup:
    1. What is the adaptor's SCSI ID?
    7
    Quote
    2. List devices, position in the chain and their corresponding SCSI ID's.
    #7 Adaptec 2930CU card
    #4 Nikon Coolscan LS30 scanner
    #3 Umax Astra 1220S scanner
    #5 Iomega ZIP 100 drive
    Quote
    3. What type of terminination are you using?
    Adaptec card has auto-termination.
    ZIP drive has a termination connector attached.
    Quote
    4. Are the devices in the chain functioning properly?
    Yes.
    Quote
    I agree that your problem is your SCSI controller. There may not be anything actually wrong with it. The 2930 was an agressive controller card and its BIOS simply may not coexist with your motherboard's BIOS optimally. Even with the BIOS disabled, it may be competing with the motherboard's request for handlers.
    You may want to check to see if there is a BIOS update on Adaptec's website. Adaptec usually released 1 or 2 updates for each SCSI generation they produced. It may or may not help but we need to make sure you have the latest BIOS released.
    Unfortunately, this card cannot be reflashed.
    Quote
    At any rate, I think you have found the component which is responsible for the delay. I'm willing to assist in diagnosing the issue but I need you to provide the specific information I'm requesting.
    Also, try to do a CTRL-Pause to catch exactly what the BIOS version is and any other information which is showing up with the BIOS disabled. The SCSI adaptor BIOS, in fact, should not be enabled in your SCSI configuration as you have described thus far.
    Adaptec AHA 2930CU SCSI BIOS v1.34.1.
    There seems to be a difference between BIOS and host adapter BIOS. You always get the BIOS screen, but you can disable the host adapter BIOS if it is not required.
    I am pretty sure it is not the SCSI chain that is wonr because the pause happens with nothing connected to the card.
    Jonathan

  • 875P Neo-FIS2R sound settings

    Hi,
    I just got this new board (875P Neo-FIS2R) and I'm mostly happy with it but just realize something...  After installing all provided driver in the box, after running liveupdate3 to make sure all driver are up to date, I got a problem with the onboard sound...  But before stepping to conclusion, I need your opinion/technical knowledge before buying a PCI soundcard like an Audigy...
    First, I cannot find any sound mixer that can allow me to set the bass or treble, adjust the balance etc...(if I look at the windows default mixer, I got bass and treble but they cannot be change)  Yes, I got this little icon from soundmax that allow me to change speaker setting (close together or far appart) and also I can change the environement setting like the sblive! and newer card to give specific ambient context like deep forest or bathroom (btw, for the last one, environnement setting, I can change to anything in the list but I do not hear any change... )  
    Second, for sound quality, I got chop and crop once in a while when I play mp3 or CD music...  Generally, I found the sound to be bizarre...  
    So, maybe it's me, but I really need your opinion on this to figure out if I need to install something else or if it's just a limitaton of the onboard sound...  I know asus P4C800 is also using Soundmax but the use the SoundMax 4XL which come with a great mixer and seems to be more convenient and versatil that the solution provided by MSI on this very high end board...  
    Thanks for your cooperation in helping me out...
    TheBrute
    P4 2.80C @ FSB 200 , HT enabled, stock cooling
    Corsair XMS DDR400 2.5-3-3-6 @ 400
    875P Neo-FIS2R
    HIS ATI RADEON 9800PRO OC at 450Mhz/370Mhz
    Thermaltake Purepower 420W
    Maxtor SATA 7200rpm 8mb 120GB x 2 @ RAID0 with ICHR5
    BIOS - 2.0 + FSB200, enable USB, ACPI.
    WinXP + SP1 + all latest Windows Updates

    Hi,
        For wiring spec and speaker spec, I got a altec lansing sub + 2 satelite... wired with stock cable from altec lansing.  Very common setup...   I dont think that this is the issue...  Before, I had a NFORCE2 chipset with the MCP-T as the southbridge, which had a great onboard sound setup.  Sound was perfect and the mixer, also perfect (perfect for a gamer and mp3 playing)  So, if anyone else confirm that there is no mixer (with bass/treble control), I will have to live with it...  My next question would be: which PCI sound card do you recommend for great quality sound, 5.1,6.1 or 7.1, gaming performance and bug free with the 875P neo FIS2R ??
    Thanks
    TheBrute
    P4 2.80C @ FSB 200 , HT enabled, stock cooling
    Corsair XMS DDR400 2.5-3-3-6 @ 400
    875P Neo-FIS2R
    HIS ATI RADEON 9800PRO OC at 450Mhz/370Mhz
    Thermaltake Purepower 420W
    Maxtor SATA 7200rpm 8mb 120GB x 2 @ RAID0 with ICHR5
    BIOS - 2.0 + FSB200, enable USB, ACPI.
    WinXP + SP1 + all latest Windows Updates

  • 875P Neo-FIS2R Dead

    Hi,
       I just built a new machine with the 875P Neo-FIS2R, and it was working fine. I read that there were problems with the BIOS V1.3. Of course, I had to update my BIOS. I saw V1.4 was out and figured it was safe and fixed. So I used MSI's LIVE BIOS to flash the BIOS in Windows mode. I have done this before with my other MSI board and had no problems. The flashing process went successful, and asked me to reboot. Then when I did it never came back up. No video or POST beep. I tried switching out memory, clearing the CMOS, and even changing to my older GF3 card. Nothing worked. Can someone tell me what to do? I want my PC to work.... Again.
    Pentium 4 3.0C
    1 GB Corsair Twinx
    36 GB SATA Raptor
    MSI Neo-FIS2R
    Radeon 9800 Pro 256 MB
    SB Audigy 2

    I took out the battery and tried but it didn't work. Then I took a stick of pc2100 ddr out of my older machine and put it in, and it booted! Then I swapped out back to my new ddr 400 and it booted! Okay, so now when it boots, it says no BIOS installed and acts like I never had win xp on it. So thats alright, I can reload it, but My Cmos is like it was in 1999. Do I just load the defaults then fix it back to where it was and reload windows? Or do I need to slow down dram timings and reload windows and flash bios back to V1.2?

  • 875P Neo FiS2R best memory ??

    Aside from the list on the MSI web site, what 512MB TWIN DDR memory modules have been tested to be working fine with the 875P Neo FiS2R motherboad ?
    Both 400 or also higher for overclocking. Please indicate your findings, thanks.

    Even though it's not on the "recommended list," I use the 2x512MB Mushkin Level II Black Label DIMMs, with the Winbond BH5 (??) chips.
    My 875P-FIS2R board is stable even overclocked. I run the memory at 2-2-2-6 w/ 8 Burst and DDR Volt at 2.85V. The RAM is good for 2-2-2-5 and works on the board at that setting, but not when I OC past 245FSB (3:2 Ratio) with a 2.4C, so I drop it to 2-2-2-6 and I'm at a happy 3.0GHz with very aggressive timings.
    Personally, I wish I could get the same results at 1:1 ratio, but it appears my SB Audigy might be holding me back on that endeavor (I can OC considerably higher just by taking the Audigy out). Anyway, my memory settings always gets me > 1000 on my PCMark2003 Memory score. So I'm happy (for now!!).

  • Issues with powering 875p neo

    Hello,
    I am having some problems with the 875p neo, which seems to be the consensus here.  After changing the memory clock setting from 2.5 5 5 8 to 2 2 2 6, and vga to 64 to 128, voltage from 2.5 to 2.7, the computer upon powering up, the led light goes on, the cd lights go on, the monitor light stays orange, you can hear the fans working and otherwise appears to be booting up with the exception of a blank screen.  When I hit the reset button the monitor light turns green and boots up with no problems.  I set the bios settings back to factory settings, and restored my windows back to a previous day ruling out any possible conflicts.  It still happens.
    After all of the above, I installed the live update from the website to upgrade the bios, and when performing the autosearch feature, it becomes non-responsive on "mainboard driver version".  I tried uninstalling it and reinstalling it again and it hangs up at the same place.
    Also, the hdd led light doesn't work with IDE harddrives
    These are the pc specs
    875p Neo motherboard
    Intel P4 processor
    1024 mb of Corsair ddr3200 RAM
    Gforce 4 128mb graphics card
    Soundblaster Audigy soundcard
    60 gig Western digital main harddrive
    250 gig Western Digital slave harddrive (both hooked up onboard with an ide cable.
    Creative PC-DVDrom
    Cendyne lightning iv cd burner
    Any help would be appreciated.

    I see you dumped the board, but to run a Sempron you have to update the bios to version 1.30. To solve errors in temp readings you want version 1.40.
    I know you have to have a chip on the board to reflash the bios, but in all fairness, the Semprons came out after the board did, so having them not work without a reflash is understandable.

  • 875P NEO FIS2R problems with booting at power-up

    Having problems with booting at power-up.
    Recently, with no apparent modification to system - at power up the system will often not boot.  About 80% of time systems seems to go into a loop with CD/DVD drive light blinking a few times, then the floppy drive light comes on and can hear the FDD run – within 30 seconds or so, this process starts over again.  Power switch LED is on and HDD LED is on (continuously).  All fans are running (power supply fan, case fan, CPU fan and Intel Canterwood 875 fan ).
    Monitor power on light is in power save mode (amber) when system does not boot.  When boot is successful the monitor power light turns green immediately.
    After pressing the reset button several times (varies between pressing reset button 1 time to 30 or more times) system will then boot OK or go into set up.
    Once running there is no apparent problem.
    This mainboard comes with D Bracket containing 2 USB 2.0 ports, and 4 diagnostics LEDs - when boot problem occurs the diagnostic LEDs, give a code that in the MSI mainboard manual states “Initializing Keyboard Controller” and diagnostic LEDs stays in this mode until via reset button provides a successful boot and start up.
    Have reseated all connectors.
    SYSTEM
    Mainboard – MSI 875P Neo FIS2R   (MSI 6758)
    BIOS – AMI v1.8 (has not been updated)
    CPU – Intel P4 2.6 GHz - system bus 800 MHz 512 KB L2 Cache
    Memory – 1.5 gb (2 x 256 mb and 2 x 512mb)
    Power Supply – Antec 380 watt
    HDD – IED WD 160 GB and IED WD 40 GB
    Video Card – ATI Radeon 9600 (128 RAM)
    Operating System – MS Windows XP Pro (sp2)

    Quote from: BOSSKILLER on 17-May-08, 03:34:12
    Have you done >>Clear CMOS Guide<<?
    Cleared CMOS - no change same problem.  Also, re-seated all connectors at same time.
    Quote from: Wonkanoby on 17-May-08, 09:06:54
    have you just added the second wd drive
    are they jumpered right
    jumperless if alone on ide
    jumpered master /slave if two on it
    No, second 40GB HDD was installed months before this issue started and is jumpered as slave drive.  Also, no other additional hardware installed for several months before issue.

  • 875P Neo-FIS2R boot problem

    Hello,
    Just built a new machine with the following parts. Sometimes it boots fine, but mostly when you turn it on nothing happens, no beeps, no visual, no nothing. Also, once in awhile it takes 15 - 20 seconds before it beeps and visuals come on screen. It's using bios version 1.2 with all default settings by shorting out jumpers. (It gives different voltage settings when reset by jumpers vrs utility.) Once it boots it runs fine, even though memory timings are 2-4-4-6 SPD instead of 2-2-2-6 SPD that my memory modules are suppose to be. However when I manually change to 2-2-2-6 the bios shows that but CPU-Z still shows 2-4-4-6, thats a different story though which a bios update would probally fix. Right now all I want is for it to boot consistently, every time. Ive tried a different power switch and a different power supply. Neither helped and this is driving me crazy, somebody please assist or post any information you might feel would help.
    Intel Pentium 4 2.4CGHz Processor 800MHz FSB
    MSI 875P Neo-FIS2R
    Corsair 512MB PC-3200/400MHz DDR Ram (TWINX512-3200LL)
    ASUS GeForce4 Ti4200 128MB 8X (V9280 TD)
    Integrated six channel audio on motherboard
    Western Digital 80GB 7,200RPM 8MB Cache (WD800JB)
    LITE-ON 16x/48x DVD/CD-ROM Drive (XJ-HD165H)
    LITE-ON 52x24x52 CD-RW Drive (LTR-52246S)
    TEAC 3.5" Floppy Drive               
    Black Raidmax Case with 350W Power Supply (278WB)
    CTX Executive 19" TrueFlat 1600x1200 (EX950F)
    Windows XP Home Edition Full Install
    Nice black and silver multimedia keyboard
    Microsoft Wheel Mouse Optical
    Intel 56K V.90/V.92 PCI Data, Fax, Speakerphone

    Hey,
    I have /had same problem with Neo 875 and corsair TWINX512-3200LL and bios V1.2 It has something to do with mem settings and/or Vdimm voltage. At this moment it boots fine but I can't explain way. It seems that this kind of memory is very sensitive for the Vdimm voltage. 2.5V is to low and some systems refuse to post. (see the bios 1.4 flash problems) Must user use 2.6v; 2.65v or 2.7v. Check out if you can find a stable setting. Bios v1.2 uses default SPD settings. you can't change them. Although after bios reset (removed battery) I get some different values with cpu-z. 2-2-2-6 I don't understand why I get those values in CPU-Z. I don't believe that my system is running with those settings. I think it's running with default bios 1.2 settings 2,5-4-4-6 but who knows?
    A lot of users had dead MOBO's when they flashed to v1.4. The reason isn't found. Some moderators say the didn't wait for the DOS prompt after flashing (Could be) Some users can confirm they did. Maybe it has to do with the corsair memory. If you do a search you will find a lot of usefull information (bios v1.4 and/or MOBO hangs on keyboard initialisation)

  • Need help with 875P Neo-FIS2R!! No on board lan??

    Hey i just  got the 875P Neo-FIS2R, it came with bios 1.2 on it.
    At that point I got everything working nice, INcluding the onboard lan card. I then went to live update bios to 1.6 through windows and I had no problems, but after I restarted my comp. it came back on with out detecting the onboard lan?? It was detected before,but ever since I updated to bios 1.6, it doesn't dectect the lan anymore!!! Anything I can do??

    It could be something simple. Did you check to see if the onboard LAN is Enabled in the Bios?
    I'd check that first!

Maybe you are looking for