Problem with my batery

Hi all,
Have a brand new Yoga 15 thinkpad. When my baterry reach 45% of capacity, sudenly comes to
6% of capacity and later shutdown.
What can I do?
Tks.

First, charge the iPad for several hours using the charger that came with the iPad. Do NOT use an iPhone charger or an iPod charger. You want the one that has a 2.1A output (yes, the labeling is almost impossible to read).
Then (if necessary), try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here.

Similar Messages

Problems with the batery of my laptop

hello i have my laptop hp envy 14, the batery load reaches 18% and does not charge more. The batery is new but it serves me, show you what I get the test tell me what the problem is.
the battery is warranted? It can be a problem in my charger?I used Battery Test look at this :
Battery Test: Primary - Replace 45 Secondary - NOT INSTALLED 60
FAILURE ID: RGFBPW - 5N97HU - PXGV5G - C0FK03
PRODUCT ID: XQ104AAR.
thank you
jose ortega

@joseortega
Thank you for visiting our English HP Support Forum. We are only able to reply to posts written in English. To insure a quick response it would be advisable to post your question in English. The following links are here to assist you if you prefer to post in the following Language Forum.
English: http://h30434.www3.hp.com
Spanish: http://h30467.www3.hp.com
French: http://h30478.www3.hp.com
Portuguese: http://h30487.www3.hp.com
German: http://h30492.www3.hp.com
Korean: http://h30491.www3.hp.com/t5/community/communitypage
Simplified Chinese: http://h30471.www3.hp.com/t5/community/communitypage
I Work for HP

Problems with my DvdRW TS-L632N - I need help

Can someone to give me some advice, to solve the problems?
I had Some problems with my DVDRW, didn't want to burn some dvds - in device manager i uninstalled the device and after that I tried to installed , but the result was a disaster . Vista Home Premium didn't sees the DVDRW drive (TS-L632N/HPMH).
I removed the batery and i removed the DVD device and i put it in, without any result. It didn't see in My Computer and Device manager.
I made these operations without success:
1. Device manager/uninstal the DVD, scan for hardware change and the result it was that i can't find
my DVD unit. (it disappeared and no longer can see in device manager and my computer - I can't
install because i can't find)
2. I change my Dvd unit with a new one, without any result, it wasn't be found it in device manager.
3. I instaled The software Microsoft Fix It, the result was that my DVD unit couldn't be found.
4. I updated my Bios, without any result.
5. I check in Bios to see if i have in Change boot order , boot from DVD, there is.
Please help me to solve at least one of the two problems that I have.
Can you give me some advice, to solve the problems?
I feel crazy.......I wait your reply,thanks a lot .....

What is the product?

Immportand. Problems with MB. Please help.

Hello
Im having a problem with my PC in the moust unpleasent moment as I can’t do my college work and I cant afford new PC in the next 4 months, so any help with my problem will be grealty appriciated.
OK.
Here is my problem.
When I work and that’s usualy using Internet and Office XP my PC is starting to slow down (mouse cursor is scroling very slow, I cant close windows) and afther a while its turning off. Whell its not turn off exactly because CPU, GPU and PSU fans are still working but the monitor is turing on stand by. When this happens I can’t do restart so I have to puss power on/off button on the case of the PC to turn the PC off. If I try to turn in on afther that NumLock and CapsLock indicators on the keyboard will flash for a second as well as monitor and again only CPU, GPU and PSU fans works but the system is not starting. This happened several times and every time till now I waited for a day to start my PC again. That was till the last time. Now afther 4 days I still can’t to start my PC.
NOTE.
When I opned the case four led diodes that are on my MSI mainboards were lightning red. In the manual explanation for this is “The procesor might be damage or not instaled properly. Damage/discharge lithium batery”
I doubt that the problem is procesor because the PC will never start if the procesor is damaged of instaled properly.
Iv also changed lithium batery but the problem remained.
And another thing. PC Alert 4 somethimes showd that CPU and system tempetarure were 78 C. Afther this restart the system and went in bios to see if that was the real temperature but the bios showed 32 C for procesor and 22 for system.
I have the latest drivers, bios and updates for windows. Iv checked for viruses with the latest updates for Pc-cillin 2002 and I didn’t find any viruses. Iv cheked every componets on other configuratios and they worked fine.
Now a frend of me told me that the cause of problem are condenzator on mainboard araund the procesor.
If you know whats is the problem please help me to resolve it.
Thank you..

Please tell us more about your system, including PSU.
It sounds very, very much like a melted condensator. It is not hard to check:
Open case and look for brown or darkcoloured... yecch... on the motherboard. Another symtom will be harder and harder to start and more and more frequent shut downs.
There are people here I believe that can guide you to change them. I would get another board because the problem might happen again. In either case, save all important work, logins, etc. to an external unit. Mail it to a friend if nothing else is available.

A problem with threads

I am trying to implement some kind of a server listening for requests. The listener part of the app, is a daemon thread that listens for connections and instantiates a handling daemon thread once it gets some. However, my problem is that i must be able to kill the listening thread at the user's will (say via a sto button). I have done this via the Sun's proposed way, by testing a boolean flag in the loop, which is set to false when i wish to kill the thread. The problem with this thing is the following...
Once the thread starts excecuting, it will test the flag, find it true and enter the loop. At some point it will LOCK on the server socket waiting for connection. Unless some client actually connects, it will keep on listening indefinatelly whithought ever bothering to check for the flag again (no matter how many times you set the damn thing to false).
My question is this: Is there any real, non-theoretical, applied way to stop thread in java safely?
Thank you in advance,
Lefty

This was one solution from the socket programming forum, have you tried this??
public Thread MyThread extends Thread{
     boolean active = true;
     public void run(){
          ss.setSoTimeout(90);
          while (active){
               try{
                    serverSocket = ss.accept();
               catch (SocketTimeoutException ste){
               // do nothing
     // interrupt thread
     public void deactivate(){
          active = false;
          // you gotta sleep for a time longer than the
          // accept() timeout to make sure that timeout is finished.
          try{
               sleep(91);
          }catch (InterruptedException ie){
          interrupt();
}

Problem with Threads and a static variable

I have a problem with the code below. I am yet to make sure that I understand the problem. Correct me if I am wrong please.
Code functionality:
A timer calls SetState every second. It sets the state and sets boolean variable "changed" to true. Then notifies a main process thread to check if the state changed to send a message.
The problem as far I understand is:
Assume the timer Thread calls SetState twice before the main process Thread runs. As a result, "changed" is set to true twice. However, since the main process is blocked twice during the two calls to SetState, when it runs it would have the two SetState timer threads blocked on its synchronized body. It will pass the first one, send the message and set "changed" to false since it was true. Now, it will pass the second thread, but here is the problem, "changed" is already set to false. As a result, it won't send the message even though it is supposed to.
Would you please let me know if my understanding is correct? If so, what would you propose to resolve the problem? Should I call wait some other or should I notify in a different way?
Thanks,
B.D.
Code:
private static volatile boolean bChanged = false;
private static Thread objMainProcess;
   protected static void Init(){
        objMainProcess = new Thread() {
            public void run() {
                while( objMainProcess == Thread.currentThread() ) {
                   GetState();
        objMainProcess.setDaemon( true );
        objMainProcess.start();
    public static void initStatusTimer(){
        if(objTimer == null)
             objTimer = new javax.swing.Timer( 1000, new java.awt.event.ActionListener(){
                public void actionPerformed( java.awt.event.ActionEvent evt){
                          SetState();
    private static void SetState(){
        if( objMainProcess == null ) return;
        synchronized( objMainProcess ) {
            bChanged = true;
            try{
                objMainProcess.notify();
            }catch( IllegalMonitorStateException e ) {}
    private static boolean GetState() {
        if( objMainProcess == null ) return false;
        synchronized( objMainProcess ) {
            if( bChanged) {
                SendMessage();
                bChanged = false;
                return true;
            try {
                objMainProcess.wait();
            }catch( InterruptedException e ) {}
            return false;
    }

Thanks DrClap for your reply. Everything you said is right. It is not easy to make them alternate since SetState() could be called from different places where the state could be anything else but a status message. Like a GREETING message for example. It is a handshaking message but not a status message.
Again as you said, There is a reason I can't call sendMessage() inside setState().
The only way I was able to do it is by having a counter of the number of notifies that have been called. Every time notify() is called a counter is incremented. Now instead of just checking if "changed" flag is true, I also check if notify counter is greater than zero. If both true, I send the message. If "changed" flag is false, I check again if the notify counter is greater than zero, I send the message. This way it works, but it is kind of a patch than a good design fix. I am yet to find a good solution.
Thanks,
B.D.

Problem with threads running javaw

Hi,
Having a problem with multi thread programming using client server sockets. The program works find when starting the the application in a console using java muti.java , but when using javaw multi.java the program doesnt die and have to kill it in the task manager. The program doesnt display any of my gui error messages either when the server disconnect the client. all works find in a console. any advice on this as I havent been able to understand why this is happening? any comment would be appreciated.
troy.

troy,
Try and post a minimum code sample of your app which
does not work.
When using javaw, make sure you redirect the standard
error and standard output streams to file.
Graeme.Hi Graeme,
I dont understand what you mean by redirection to file? some of my code below.
The code works fine under a console, code is supposed to exit when the client (the other server )disconnects. the problem is that but the clientworker side of the code still works. which under console it doesnt.
public class Server{
ServerSocket aServerSocket;
Socket dianosticsSocket;
Socket nPortExpress;
ClientListener aClientListener;
LinkedList queue = new LinkedList();
int port = 0;
int clientPort = 0;
String clientName = null;
boolean serverAlive = true;
* Server constructor generates a server
* Socket and then starts a client threads.
* @param aPort      socket port of local machine.
public Server(int aPort, String aClientName, int aClientPort){
port = aPort;
clientName = aClientName;
clientPort = aClientPort;
try{
// create a new thread
aServerSocket = new ServerSocket(port) ;
// connect to the nPortExpress
aClientListener = new ClientListener(InetAddress.getByName(clientName), clientPort, queue,this);
// aClientListener.setDaemon(true);
aClientListener.start();
// start a dianostic port
DiagnosticsServer aDiagnosticsServer = new DiagnosticsServer(port,queue,aClientListener);
// System.out.println("Server is running on port " + port + "...");
// System.out.println("Connect to nPort");
catch(Exception e)
// System.out.println("ERROR: Server port " + port + " not available");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Server port " + port + " not available", JOptionPane.ERROR_MESSAGE);
serverAlive = false;
System.exit(1);
while(serverAlive&&aClientListener.hostSocket.isConnected()){
try{
// connect the client
Socket aClient = aServerSocket.accept();
//System.out.println("open client connection");
//System.out.println("client local: "+ aClient.getLocalAddress().toString());
// System.out.println("client localport: "+ aClient.getLocalPort());
// System.out.println("client : "+ aClient.getInetAddress().toString());
// System.out.println("client port: "+ aClient.getLocalPort());
// make a new client thread
ClientWorker clientThread = new ClientWorker(aClient, queue, aClientListener, false);
// start thread
clientThread.start();
catch(Exception e)
//System.out.println("ERROR: Client connection failure");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Client connection failure", JOptionPane.ERROR_MESSAGE);
}// end while
} // end constructor Server
void serverExit(){
     JOptionPane.showMessageDialog(null, "Server ","ERROR: nPort Failure", JOptionPane.ERROR_MESSAGE);
     System.exit(1);
}// end class Server
*** connect to another server
public class ClientListener extends Thread{
InetAddress hostName;
int hostPort;
Socket hostSocket;
BufferedReader in;
PrintWriter out;
boolean loggedIn;
LinkedList queue;      // reference to Server queue
Server serverRef; // reference to main server
* ClientListener connects to the host server.
* @param aHostName is the name of the host eg server name or IP address.
* @param aHostPort is a port number of the host.
* @param aLoginName is the users login name.
public ClientListener(InetAddress aHostName, int aHostPort,LinkedList aQueue,Server aServer)      // reference to Server queue)
hostName = aHostName;
hostPort = aHostPort;
queue = aQueue;
serverRef = aServer;
// connect to the server
try{
hostSocket = new Socket(hostName, hostPort);
catch(IOException e){
//System.out.println("ERROR: Connection Host Failed");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Connection to nPort Failed", JOptionPane.ERROR_MESSAGE);
System.exit(0);
} // end constructor ClientListener
** multi client connection server
ClientWorker(Socket aSocket,LinkedList aQueue, ClientListener aClientListener, boolean diagnostics){
queue = aQueue;
addToQueue(this);
client = aSocket;
clientRef = aClientListener;
aDiagnostic = diagnostics;
} // end constructor ClientWorker
* run method is the main loop of the server program
* in change of handle new client connection as well
* as handle all messages and errors.
public void run(){
boolean alive = true;
String aSubString = "";
in = null;
out = null;
loginName = "";
loggedIn = false;
while (alive && client.isConnected()&& clientRef.hostSocket.isConnected()){
try{
in = new BufferedReader(new InputStreamReader(client.getInputStream()));
out = new PrintWriter(new OutputStreamWriter(client.getOutputStream()));
if(aDiagnostic){
out.println("WELCOME to diagnostics");
broadCastDia("Connect : diagnostics "+client.getInetAddress().toString());
out.flush();
else {
out.println("WELCOME to Troy's Server");
broadCastDia("Connect : client "+client.getInetAddress().toString());
     out.flush();
String line;
while(((line = in.readLine())!= null)){
StringTokenizer aStringToken = new StringTokenizer(line, " ");
if(!aDiagnostic){
broadCastDia(line);
clientRef.sendMessage(line); // send mesage out to netExpress
out.println(line);
out.flush();
else{
if(line.equals("GETIPS"))
getIPs();
else{
clientRef.sendMessage(line); // send mesage out to netExpress
out.println(line);
out.flush();
} // end while
catch(Exception e){
// System.out.println("ERROR:Client Connection reset");
                         JOptionPane.showMessageDialog(null, (e.toString()),"ERROR:Client Connection reset", JOptionPane.ERROR_MESSAGE);
try{
if(aDiagnostic){
broadCastDia("Disconnect : diagnostics "+client.getInetAddress().toString());
out.flush();
else {
broadCastDia("Disconnect : client "+client.getInetAddress().toString());
     out.flush();
// close the buffers and connection;
in.close();
out.close();
client.close();
// System.out.println("out");
// remove from list
removeThreadQueue(this);
alive = false;
catch(Exception e){
// System.out.println("ERROR: Client Connection reset failure");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Client Connection reset failure", JOptionPane.ERROR_MESSAGE);
}// end while
} // end method run
* method run - Generates io stream for communicating with the server and
* starts the client gui. Run also parses the input commands from the server.
public void run(){
boolean alive = true;
try{
// begin to life the gui
// aGuiClient = new ClientGui(hostName.getHostName(), hostPort, loginName, this);
// aGuiClient.show();
in = new BufferedReader(new InputStreamReader(hostSocket.getInputStream()));
out = new PrintWriter(new OutputStreamWriter(hostSocket.getOutputStream()));
while (alive && hostSocket.isConnected()){
String line;
while(((line = in.readLine())!= null)){
System.out.println(line);
broadCast(line);
} // end while
} // end while
catch(Exception e){
//     System.out.println("ERRORa Connection to host reset");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Connection to nPort reset", JOptionPane.ERROR_MESSAGE);
try{
hostSocket.close();
     }catch(Exception a){
     JOptionPane.showMessageDialog(null, (a.toString()),"ERROR: Exception", JOptionPane.ERROR_MESSAGE);
alive = false;
System.exit(1);
} // end method run

Problem with threads and camera.

Hi everybody!
I've a problem with taking snapshot.
I would like to display a loading screen after it take snapshot ( sometimes i
have to wait few seconds after i took snapshot. Propably photo is being taken in time where i have to wait).
I was trying to use threads but i didn't succeed.
I made this code:
display.setCurrent(perform);
        new Thread(new Runnable(){
            public void run() {
                while((!performing.isShown()) && (backgroundCamera.isShown())){
                    Thread.yield();
                notifyAll();
        }).start();
        new Thread(new Runnable(){
            public void run() {
                try {
                    this.wait();
                } catch(Exception e) {
                    exceptionHandler(e);
                photo = camera.snapshot();
                display.setCurrent(displayPhoto);
        }).start();This code is sometimes showing performing screen but sometimes no.
I don't know why. In my opinion performing.isShown() method isn't working correctly.
Does anyone have some idea how to use threads here?

Hi,
I've finally managed to work this fine.
The code:
       Object o = new Object();
       display.setCurrent(perform);
        new Thread(new Runnable(){
            public void run() {
                while(!performing.isShown()){
                    Thread.yield();
               synchronized(o) {
                  o.notify();
        }).start();
        new Thread(new Runnable(){
            public void run() {
                try {
                    synchronized(o) {
                       o.wait(1);
                } catch(Exception e) {
                    exceptionHandler(e);
                photo = camera.snapshot();
                display.setCurrent(displayPhoto);
        }).start();

Problem with threads hanging

We have a problem where our application stops responding after a few days of usage. Things will for fine for a day or two, and then pretty quickly threads will start getting hung up, usually in places where they are allocating memory
We are running WebLogic 8.1 SP2 on Sun JDK 1.4.2_04 on Solaris 8 using the alternate threading model and the -server hotspot vm. We are running pretty much the same code that we had no problems with under WebLogic 6.1 SP4 and Sun JDK 1.3.1.
A thread dump usually shows that some or all of our execute threads are in the state "waiting for monitor entry" even though they are not currently waiting on any java locks. Here is a sample thread from the thread dump (we have ~120 threads so I don't want to post the full dump).
=============================================================================================
"ExecuteThread: '8' for queue: 'itgCrmWarExecutionQueue'" daemon prio=5 tid=0x005941d0 nid=0x2c waiting for monitor entry [c807f000..c807fc28]
at java.lang.String.substring(String.java:1446)
at java.lang.String.substring(String.java:1411)
at weblogic.servlet.internal.ServletRequestImpl.getRelativeUri(ServletRequestImpl.java:1872)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3492)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
=============================================================================================
String.java line 1446 for this jdk allocates a new String object, and all the other threads in this state also are creating new objects or arrays, etc.
We've done a pstack on this process when it's in this state, and the threads that are in the "waiting for monitor entry" that look like they're allocating memory are all waiting on the same lwp_mutex_lock with some allocation method that's calling into the native TwoGenerationCollectorPolicy.mem_allocate_work (see pstack output below for the same thread as in the thread dump above)
=============================================================================================
----------------- lwp# 44 / thread# 44 --------------------
ff31f364 lwp_mutex_lock (e3d70)
fee92384 __1cNObjectMonitorGenter26MpnGThread__v_ (5000, 525c, 5000, 50dc, 4800, 4af0) + 2d8
fee324d4 __1cSObjectSynchronizerKfast_enter6FnGHandle_pnJBasicLock_pnGThread__v_ (c807f65c, c807f7d4, 5941d0, 0, 35d654, fee328ec) + 68
fee32954 __1cQinstanceRefKlassZacquire_pending_list_lock6FpnJBasicLock__v_ (c807f7d4, ff170000, d4680000, 4491d4, fee1bc2c,
0) + 78
fee3167c __1cPVM_GC_OperationNdoit_prologue6M_i_ (c807f7bc, 4400, ff170000, 2d2b8, 4a6268, c807fa18) + 38
fee2e0b0 __1cIVMThreadHexecute6FpnMVM_Operation__v_ (c807f7bc, 963a8, 0, 0, 1, 0) + 90
fed2c2a4 __1cbCTwoGenerationCollectorPolicyRmem_allocate_work6MIii_pnIHeapWord__ (962c0, ff1c29ec, ff1c297c, ff131a26, 4800, 4998) + 160
fed22940 __1cNinstanceKlassRallocate_instance6MpnGThread__pnPinstanceOopDesc__ (ee009020, 5941d0, 15ca581, 3647f0, 4a6268, c807f8c8) + 180
fed34928 __1cLOptoRuntimeFnew_C6FpnMklassOopDesc_pnKJavaThread__v_ (ee009018, 5941d0, 0, 0, 0, 0) + 28
fa435a58 ???????? (ee009018, e86de, 15ca4de, 50dc, 5941d0, c807f9c8)
fb36f9a4 ???????? (0, d412ccd8, ee046c28, ff170000, 0, 0)
fad8b278 ???????? (ee046c28, d6000c90, ee046530, 8, db8e8450, c807f9e8)
fad62abc ???????? (d412ccd8, ee046530, d6000c90, ee3bfa38, 8, c807fa18)
fa4b3c38 ???????? (c807fb9c, 0, f2134700, fa415e50, 8, c807faa8)
fa40010c ???????? (c807fc28, c807fe90, a, ee9e1e20, 4, c807fb40)
fed5d48c __1cJJavaCallsLcall_helper6FpnJJavaValue_pnMmethodHandle_pnRJavaCallArguments_pnGThread__v_ (c807fe88, c807fcf0, c807fda8, 5941d0, 5941d0, c807fd00) + 27c
fee4b784 __1cJJavaCallsMcall_virtual6FpnJJavaValue_nLKlassHandle_nMsymbolHandle_4pnRJavaCallArguments_pnGThread__v_ (ff170000, 594778, c807fd9c, c807fd98, c807fda8, 5941d0) + 164
fee5e8dc __1cJJavaCallsMcall_virtual6FpnJJavaValue_nGHandle_nLKlassHandle_nMsymbolHandle_5pnGThread__v_ (c807fe88, c807fe84, c807fe7c, c807fe74, c807fe6c, 5941d0) + 6c
fee6fc74 __1cMthread_entry6FpnKJavaThread_pnGThread__v_ (5941d0, 5941d0, 838588, 594778, 306d10, fee69254) + 128
fee6927c __1cKJavaThreadDrun6M_v_ (5941d0, 2c, 40, 0, 40, 0) + 284
fee6575c _start   (5941d0, fa1a1600, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Also when it's having this problem, the "VM Thread" is always using a lot of processor time. We did a couple of pstacks today while it was having this problem, and this thread was stuck in the ONMethodSweeper.sweep for over 15 minutes when we finally killed the server.
From the thread dump:
"VM Thread" prio=5 tid=0x000e2d20 nid=0x2 runnable
From the first pstack:
=============================================================================================
----------------- lwp# 2 / thread# 2 --------------------
fed40c04 __1cXvirtual_call_RelocationIparse_ic6FrpnICodeBlob_rpC5rppnHoopDesc_pi_nNRelocIterator__ (42a2f4, fa5fa46d, ffffffff, fc4ffcb8, 42a2f4, 42a324) + 124
fed46318 __1cKCompiledIC2t5B6MpnKRelocation__v_ (42a2f0, fc4ffd24, fc4ffd4c, e802, 0, 6) + 38
fed90c38 __1cHnmethodVcleanup_inline_caches6M_v_ (fa5f7f88, fa608940, 1, 0, fa400000, 6) + 1ac
fede18b4 __1cONMethodSweeperFsweep6F_v_ (2cf38, 0, ffffffff, ff1cf1fc, ff1c66e8, fede1d44) + 1b0
fede1e6c __1cUSafepointSynchronizeFbegin6F_v_ (2cf38, ff1ba138, 5000, 50dc, 5000, 525c) + 248
feef1fd4 __1cIVMThreadEloop6M_v_ (4400, 4000, 4324, 4000, 42b0, 3800) + 3d4
feef1ae4 __1cIVMThreadDrun6M_v_ (e2d20, 2, 40, 0, 40, 0) + 8c
fee6575c _start   (e2d20, ff270200, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Second pstack
=============================================================================================
----------------- lwp# 2 / thread# 2 --------------------
fed41180 __1cXvirtual_call_RelocationIparse_ic6FrpnICodeBlob_rpC5rppnHoopDesc_pi_nNRelocIterator__ (0, ff1b9664, ffffffff, fc4ffcb8, a6f2cc, fc4ffbd0) + 6a0
fed46318 __1cKCompiledIC2t5B6MpnKRelocation__v_ (a6f2c8, fc4ffd24, fc4ffd4c, e802, 0, 6) + 38
fed90c38 __1cHnmethodVcleanup_inline_caches6M_v_ (faded4c8, fadf2c80, 1, 0, fa400000, 6) + 1ac
fede18b4 __1cONMethodSweeperFsweep6F_v_ (2cf38, 0, ffffffff, ff1cf1fc, ff1c66e8, fede1d44) + 1b0
fede1e6c __1cUSafepointSynchronizeFbegin6F_v_ (2cf38, ff1ba138, 5000, 50dc, 5000, 525c) + 248
feef1fd4 __1cIVMThreadEloop6M_v_ (4400, 4000, 4324, 4000, 42b0, 3800) + 3d4
feef1ae4 __1cIVMThreadDrun6M_v_ (e2d20, 2, 40, 0, 40, 0) + 8c
fee6575c _start   (e2d20, ff270200, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Has anyone ever seen anything like this? I'm trying to figure out if this is caused by something we're doing, or something relating to our environment and jvm options. Any ideas?

Thanks for the reply - I'm testing our app with the +UseConcMarkSweepGC now in our test environment to make sure it doesn't cause any problems there. Unfortunately the only place we've had this problem is on the production server, so it's extra difficult debugging this.
We're using the following memory options:
-ms512m -mx512m -XX:NewSize=128m -XX:PermSize=192m -XX:MaxNewSize=128m -XX:MaxPermSize=192m -XX:SurvivorRatio=8and the following debugging options, as we've also been seeing OutOfMemoryErrors ( see http://forum.java.sun.com/thread.jsp?forum=37&thread=522354&tstart=45&trange=15 )
-verbosegc -XX:+PrintGCDetails -XX:+PrintGCTimeStamps -XX:+PrintHeapAtGCBTW, which c++filt version and options are you using? Our Solaris boxes only seem to have the GNU version installed. I was trying to run that on some of the other stack traces and wasn't getting anywhere, and didn't know if because it was GNU version wouldn't work on something compiled with the Sun compiler.
Thanks!
--Andy

Problem with threads and ProgressMonitor

Dear Friends:
I have a little problem with a thread and a ProgressMonitor. I have a long time process that runs in a thread (the thread is in an separate class). The thread has a ProgressMonitor that works fine and shows the tasks progress.
But I need deactivate the main class(the main class is the user interface) until the thread ends.
I use something like this:
LongTask myTask=new LongTask();
myTask.start();
myTask.join();
Now, the main class waits for the task to end, but the progress monitor don`t works fine: it shows only the dialog but not the progress bar.
What's wrong?

Is the dialog a modal dialog? This can block other UI updates.
In general, you should make sure that it isn't modal, and that your workThread has a fairly low priority so that the UI can do its updating

Problem with threads and/or memory

I'm developing an application where there are 3 threads. One of them sends a request to the other, and if the 2nd can't answer it, it sends it to the 3rd (similar to CPU -> CACHE -> MEMORY). When i run the program with 1000-10.000 requests, no problem occurs. When i run it with 300.000-1.000.000 requests, it sometimes hangs. Is this a problem with the garbage collector, or should it be related to the threads mecanism.
(note: eache thread is in execution using a finite state machine)

i had been running the program inside Netbeans.
Running the jar using the command line outside
Netbeans i have no more problems... Does Netbeans use
it's own JVM?Depends how you set it up, but look under the options. There are settings for the compiler and jvm that it uses.

Installation problem with NW'04 SR1: database connection failed

Hi all,
while installing NW '04 SR1 on Windows Server 2003 SP1 and MS SQL Server 2000 SP4 I ran into an error related to the database connection. While performing the step "Load Java Database content" SAPinst crashes with the message
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
The connection to the SLQ Server with e.g. the Query Analyzer is OK. I had a problem with this installation setup before (have a look at the corresponding <a href="https://forums.sdn.sap.com/thread.jspa?threadID=338638&tstart=0">thread</a> ), the JDBC drivers where missing on the installation master but after copying them in the right direction the installation went on with no problem up to this point...
Has anybody an idea what could have happened here? Is this maybe a problem connected to the one I recently had
Below I attached the sapinst.log and jload.log with more detailed messages.
sapinst.log ###########
INFO 2007-03-12 22:06:24
Working directory changed to C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_~1\ONE_HOST.
INFO 2007-03-12 22:06:24
Output of D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log' is written to the logfile C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_~1\ONE_HOST/jload.java.log.
WARNING 2007-03-12 22:06:26
Execution of the command "D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log'" finished with return code 1. Output:
java version "1.4.2_13"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_13-b06)
Java HotSpot(TM) Client VM (build 1.4.2_13-b06, mixed mode)
12.03.2007 22:06:25 com.sap.inst.jload.Jload main
INFO: Jload -sec WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key -dataDir S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP -job C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML -log C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log
12.03.2007 22:06:26 com.sap.inst.jload.Jload main
SCHWERWIEGEND: couldn't connect to DB
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
ERROR 2007-03-12 22:06:26
CJS-20065 Execution of JLoad tool 'D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log'' aborts with returncode 1. Check 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log' and 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.java.log' for more information.
jload.log ###########
12.03.07 22:06 com.sap.inst.jload.Jload main
INFO: Jload -sec WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key -dataDir S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP -job C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML -log C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log
12.03.07 22:06 com.sap.inst.jload.Jload main
SEVERE: couldn't connect to DB
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
Best regards,
Bernd

Hello Kairat,
Please follow the below mentioned guide to install it.
Check all the parameters to set and run pre requisite checker before starting installation.
Keep in mind that before starting any SAP installation you should always run prerequisite checker.
https://websmp205.sap-ag.de/instguides --> SAP Netweaver -->SAP Netweaver 7.0 -- > Installations --> EHP2
Regards,
Amit Barnawal

My app store wont let me download apps, says the card is expired and theres a problem with previous purchase can someone help me pls?

My app store wont let me download apps, asks me to update my payment details then says theres a problem with previous purchase and card is expired which is untrue someone help me pls

This is a User to User Forum...
See Here for
Mac Apps Store Customer Service
http://www.apple.com/support/mac/app-store/contact.html?form=account
iTunes Customer Service Contact
http://www.apple.com/support/itunes/contact.html

Problem with item and/or data during page-processing-PS/SQL

Greetings!
On my page I have a custom report (from 2 tables) and a small form-field, that adds and edits data in the report. After generating the form with the wizard I added an extra item, to store the id from one of the tables from the report data.
Now, on submit a calculation should take place, that updates data according user input with a procedure in Page-Prosseses:
declare a number;
begin
case :PLATZ
when 1 then a:=100;
when 2 then a:= 50;
else a:=25;
end case;
update TBL_MITGLIEDER set TURNIERPUNKTE = TURNIERPUNKTE + a
where ID_MITGL = :P14_ID_MITGL;
end;
:PLATZ is user selected (1,2,3), :P14_ID_MITGL stores the reference to TBL_MITGLIEDER (and shows the change, when I select another record)
As I understand, that process should also run, when I submit a chance, but nothing happens then.
But when I try to save a new record (which worked without any problems before adding that process), I get this error message:
ORA-06550: line 1, column 64: PL/SQL: ORA-00957: duplicate column name ORA-06550: line 1, column 7: PL/SQL: SQL Statement ignored
Error Unable to process row of table TBL_TURNIERSIEGER.
Then, when I go back into the app-builder and try to run the page again, I get this message:
ORA-01403: no data found
Error Unable to fetch row.
I am not sure, if you guys have all the information you need, to know whats going on. Maybe this has to do with session-id and the whay, items are updated. I hope you can help me.
Thanks, best regards,
tobi

First can you please post all log file errors
>> I can't really give you a solution or specific recommendation since I did not saw this error yet myself, but on your own risk you can try:
1. You may try to just register 'dts.dll' using regsvr32.exe, but this error may indicate a bigger problem with setup.
If you are running SQL Server 64bit then try running this at the command prompt: %windir%\syswow64\regsvr32 "%ProgramFiles(x86)%\Microsoft SQL Server\90\dts\binn\dts.dll"
2. You can try reinstall from start (In this case you have to make sure that you un-install all)
[Personal Site] [Blog] [Facebook]

Problem with Gnome3 and/or graphics card Nvidia 8600M GT

Feb 22 07:40:21 localhost dbus[712]: [system] Failed to activate service 'org.freedesktop.Avahi': timed out
Feb 22 07:50:30 localhost kernel: [ 679.031379] gnome-shell[1277]: segfault at 10 ip 00007f3bbd305c0f sp 00007f3b84ff86d8 error 6 in libnvidia-tls.so.295.20[7f3bbd305000+3000]
Feb 22 07:50:31 localhost gnome-session[888]: WARNING: Application 'gnome-shell.desktop' killed by signal
Feb 22 07:50:35 localhost kernel: [ 683.420948] gnome-shell[1300]: segfault at 10 ip 00007f43bc84dc0f sp 00007f43877fd6d8 error 6 in libnvidia-tls.so.295.20[7f43bc84d000+3000]
Feb 22 07:50:35 localhost gnome-session[888]: WARNING: Application 'gnome-shell.desktop' killed by signal
Feb 22 07:50:35 localhost gnome-session[888]: WARNING: App 'gnome-shell.desktop' respawning too quickly
Feb 22 06:52:39 localhost rtkit-daemon[1004]: Successfully made thread 1420 of process 1420 (/usr/bin/pulseaudio) owned by '1000' high priority at nice level -11.
Feb 22 07:52:39 localhost goa[1441]: goa-daemon version 3.2.1 starting [main.c:112, main()]
Feb 22 07:58:22 localhost kernel: [ 1150.316794] CE: hpet increased min_delta_ns to 20113 nsec
Hi,
Here is my /var/log/messages.log output.
Since several days my computer repeatedly restarts programs that require at least a bit memory, such as firefox ('segmentation fault'), skype, virtualbox, generaly gnome 3 environment. Sometimes it happens that the system hangs and I can't do nothing, although I can hear that hard disk is working - at that moment only hard reset helps.
I know that the Dell Inspiron laptops (1720) have problems with Nvidia 8600M GT (the cold solder). Is it like that this time? Or maybe something wrong with the memory, CPU (Core Duo) cache memory?
I will be happy to add any additional information.
Regards,
Lukasz

Did you update the nividia driver recently?
there are some threads on this

Problem with my batery

Similar Messages

Maybe you are looking for