Problem with Network Magic/Connecting to my PS3

Hello!
I've really been enjoying my Cisco Wireless-G WRT-54G2 for the last two months, using it as a wireless hookup to my PS3. However, yesterday morning sometime something on my PC hiccupped or something . . . it's an older '04 Sony Vaio- whenever I try to install Windows XP MS Service Pack 2 (it has 1)- it goes into terminal slowdown . . . but it hasn't had any problems until this morning, when I lost the internet connection on both the land line connected to my PC and the wireless one connected to my PS3. I don't know really what happened, though the only new error that seems to have come up is that my Norton AntiVirus is thtrowing out an "Auto-Protect" error that can't seem to get resolved . . .
So, in order to troubleshoot, since my wireless modem wasn't covered by Cox Communications, I was forced to unhook it from the system and hook the ethernet line directly from the cable modem into my PC (instead of the wireless router). Eventually the problem was solved. Unfortunately, things did not return back to normal when I hooked up the wireless router again. The lights are flashing that the connection on BOTH my wireless connection and my hardline connection to my PC are going strong, but only my PC connection is working. My PS3 is programmed for the system but always gets a DNS when it tries to do anything.
When I use network magic, it inform me that "You are connected to a New Network" called "Local Area Connection - Router" and I cannot access the Map and Status Center features because of this.
What a wonderful way to be spending my turkey day!!
Any suggestions? Is the Norton AntiVirus screwing me up? I'd appreciate any assistance anyone could provide.
Eric Bowling
(Mod note: Removed non-public information. Thank you.)
Message Edited by Vince_02 on 11-25-2009 05:09 AM

It is fairly easy and you should be up before Turkey day
If you know your PS3 has the correct security key for Network Magic (WEP or preferrably WPA WPA2 ) then follow this.
Open Network Magic>Click on (Network) Tasks>Click on Add a Device>(I have network lock on always to prevent intruders) it should disable your network lock>Follow the prompts, make sure your PS3 is on and click on internet or something to make it grab an IP addy, and show it's MAC addy, as well>
When Network Magic's "add a Device Wizard" starts looking for your PS3's MAC address, and you see a MAC address appear below the "searching" line>
you should be fine(and be able to click Finish) then, as it will be included as a device with access to your Router>It should re-engage your Network Lock.
Kind regards,
Dagra
PS. I just started using Network Magic about 2 weeks ago, and got the 5.5 pro, for my home network. It took me about 30 minutes to get it all connected including my PS3, but then I'm an IT Tech.
Message Edited by Dagra on 11-25-2009 06:17 PM

Similar Messages

Does anyone have problems with Network Magic slowing computers down?

Our company has been using Network Magic for several years without too many problems. The problem is with some of the recent updates, our Norton Program keeps telling us that Network Magic is slowing our system down. Things are so slow with almost everything it feels like we are back to dial up internet and the sit and wait game to see files on other computers. Any help would be greatly appreciated.

Try This...
Close All Open Apps... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430

Problems with n97 apps connecting to network (Voda...

Problems with n97 apps connecting to network (Vodafone UK – 3G)
Recently a number of my apps which used to connect automatically to the internet (which ever was available – known wi-fi or 3g) have stopped doing this. They now only connect to one known wi-fi.
I’ve tried uninstalling and reinstalling each app, but this hasn’t solved the problem. I’ve checked for software updates and do not believe any have been applied or are available. All apps have been downloaded via Ovi on the phone. I still am able to access the internet by the web browser which was installed on the phone and via google maps (which also still manages GPS position, search, etc).
The apps which I notice causing a problem are:
Sainsbury’s/nectar
Tesco
Map my tracks
Snaptu
Opera Mini
Any one got any ideas???

I have the same problem since i updated my mac to 10.5.6.
Each time I have to do a diagnostic and retype the WEP password to have the internet connection.

SAP Screen Personas error "A problem with network connectivity has been detected"

Hi,
We just installed Personas release 100 SP02 and performed the
configuration steps necessary. But when we acces the url and logon to
personas we get the following erre
A problem with network connectivity has been detected.
Please check you connection and refresh your browser.
Any help to solve this issue would be appreciated.
Best Regards.

Please use this checklist to see if everything is correct:
1. restgui service handler class has CL_HTTP_EXT_ITS_BASIC
2. SPRO -> Sap screen Personas -> Maintain system has
       - 3 letter system id
       - "Server.Url" without typo and value in http(s)://<SERVER>:<PORT>/ format
       - "Service.Uri" without typo and value as /restgui
3, Note 2026487 is installed
4. If target system is different from source system then you are able to access the following
         - http(s)://<TARGETSERVER>:<PORT>/clientaccesspolicy.xml
         - http(s)://<TARGETSERVER>:<PORT>/crossdomain.xml
5. role is assigned to user under /n/persos/admin_ui -> User Maintenance -> Search -> Show user -> Role
If you still get error, then if you are using SSO, please check if you have configured login/create_sso2_ticket parameter correctly.
Thanks
Chinthan

Upgrading to 6.1.1 hasn't solved the problem with network connection on 4S. Still "No Servise"!

Upgrading to 6.1.1 hasn't solved the problem with network connection on 4S. Still "No Servise"!

Same here. Everything was fine running on ios 6.0, I don't know what possessed me to upgrade! I contacted O2 and thet went through the usual settings; reboot; airplane mode etc and it works for a while (like 5 mins) then service is losted with the network. I've even deleted the exchange email account and rebooted as read on the internet that this would fix the problem.... guest what....yep no joy! This is clearly a faulty software update and need fixing pronto! I've read that ios6.1.2 will be out soon to fix the firmware that was suppose to fix the initial network problem. When will this be realeased Apple?! It's hardly fit for purpose when I can't make calls or surf the internet.

Network magic connection stopped working last night

Really need help with this.
My network magic suddenly yesterday stopped working in that it cannot contact the network magic website. This leads it to conclude that the internet is down, even though the connection is fine. This happened on all three of my computers. My browsers (mozilla and explorer) cannot seem to connect to the network magic website either. A product re-install on one of the computers went fine, but the problem still persists, despite a re-boot. Examined the hosts file manually and there are no entries that might cause a problem. The computers use different service provides and a different router. All three are vista ultimate 64 bit with service pack 2 (recently installed), have spyware doctor, spybot, and live care for security tools (as well as network magic). The live care firewall has the correct permissions for network magic. The network magic platform service is running properly.
Of course I cannot contact the network magic support team as I cannot access the website - this does not appear to be a known problem (did a search).
Peter

Peter,
Not only the Network Magic connection stopped, but if you try to connect with your Net2Go remote access website it's not there anymore. Not even if you try to connect with your computer that's hosting it.
As I understand it, when Cisco aquired Pure Networks they issued their last upgrade, and with it came the announcement that the latest version would no longer have the Net2Go feature. Indeed, they could choose to END Net2Go at their discretion. It would seem that this is the case. A shame, really. My clients have come to depend on being able to retrieve their material and email links to their clients as well. All Cisco had to do was provide a redirect, how much server power can that take up anyway? It was almost like having a web site, and it cost nothing. Sure was nice.
According to the End-Of-Life protocols as laid out by Cisco, they're supposed to give warning when there's a system they would no longer support, and they are supposed to get with you to help you ease into the replacement technology and give you several months to do so. Slamming the door wasn't supposed to be part of it.
So now we have to either go without because nobody offers anything remotely like it (I checked), or we can all get domain names and pay for web sites and hosting. Thanks a lot, Cisco.

Network Magic Connection Speed Fix

This came Directly Fom the net work Magic team.
Our engineering team has informed us that the issue is now fixed, please retry the speed test, if it still fails you will need to delete a Network Magic reg file and reboot your computer, please try the following: 1. Verify if you have 32 or 64bit operating system: *Click Start and right click on Computer and select Properties *Under the "System" it will show either 32 or 64bit. 2. Click on Start 3. In the Search field type REGEDIT and press enter. 4. Depending if you have 32 or 64 bit operating system, navigate to the following path: *64-bit OS: HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Pure Networks\Platform\1033\SpeedTest\nm and delete the "nm" folder only *32-bit OS: HKEY_LOCAL_MACHINE\SOFTWARE\Pure Networks\Platform\1033\SpeedTest\nm and delete the "nm" folder only. 5. Close all the windows and reboot the computer. This should fix the Problem of Connection Speed. not showing up redirecting some where else.
(Mod Note: Email address removed.)

Peter,
Not only the Network Magic connection stopped, but if you try to connect with your Net2Go remote access website it's not there anymore. Not even if you try to connect with your computer that's hosting it.
As I understand it, when Cisco aquired Pure Networks they issued their last upgrade, and with it came the announcement that the latest version would no longer have the Net2Go feature. Indeed, they could choose to END Net2Go at their discretion. It would seem that this is the case. A shame, really. My clients have come to depend on being able to retrieve their material and email links to their clients as well. All Cisco had to do was provide a redirect, how much server power can that take up anyway? It was almost like having a web site, and it cost nothing. Sure was nice.
According to the End-Of-Life protocols as laid out by Cisco, they're supposed to give warning when there's a system they would no longer support, and they are supposed to get with you to help you ease into the replacement technology and give you several months to do so. Slamming the door wasn't supposed to be part of it.
So now we have to either go without because nobody offers anything remotely like it (I checked), or we can all get domain names and pay for web sites and hosting. Thanks a lot, Cisco.

Installing Cisco E3000, conflict with Network Magic

I have replaced, for security reasons, my old Belkin with the Cisco E3000. The installation disk runs and then says will not configure router. I tried Cisco Router chat but they say it is a Network Magic problem, because the software in the install disk conflicts with Network Magic. I have checked my firewall (Sunbelt's Vipre) and did not see any problem. I am running XP SP3. I also uninstalled all the Belkin entries I can find, rebooted, and still it would not install. Somewhere, in Network Magic, has to be the process in which I need.
Information to help in diagnosis:
Network Magic version 5.5.9195.0-Pure0
Cable Connection
Cable modem is a Motorola, SB 5100
Router I am trying to install: Cisco E3000. Since it won't setup, I can't give you any info
Router Connection: Wired
Ethernet port is a PCI Card
Windows XP SP 3 with all updates
Firewall from Sunbelt software, the Vipre product versions 4.0.3904, updated 30 minutes ago
Vipre also applies to the Anti-Virus
My physical locating is Western PA, USA
I was able, with the router setting up, connect to the internet simply by plugging in the router to the modem and then PC. Plugging in the router to the cable modem was part of the setup procedure. Connecting to the PC was something I did via Network Magic. This did not set up the router.

jobanks wrote:
I have replaced, for security reasons, my old Belkin with the Cisco E3000. The installation disk runs and then says will not configure router. I tried Cisco Router chat but they say it is a Network Magic problem, because the software in the install disk conflicts with Network Magic. I have checked my firewall (Sunbelt's Vipre) and did not see any problem. I am running XP SP3. I also uninstalled all the Belkin entries I can find, rebooted, and still it would not install. Somewhere, in Network Magic, has to be the process in which I need.
Information to help in diagnosis:
Network Magic version 5.5.9195.0-Pure0
Cable Connection
Cable modem is a Motorola, SB 5100
Router I am trying to install: Cisco E3000. Since it won't setup, I can't give you any info
Router Connection: Wired
Ethernet port is a PCI Card
Windows XP SP 3 with all updates
Firewall from Sunbelt software, the Vipre product versions 4.0.3904, updated 30 minutes ago
Vipre also applies to the Anti-Virus
My physical locating is Western PA, USA
I was able, with the router setting up, connect to the internet simply by plugging in the router to the modem and then PC. Plugging in the router to the cable modem was part of the setup procedure. Connecting to the PC was something I did via Network Magic. This did not set up the router.
Hi jobanks,
Call Network Magic Support for help.
By phone: 888-812-9402
Mon-Fri, 9am-5pm Pacific Time
Sat-Sun, 11am-4pm Pacific Time
(We're closed on most US national holidays.)
thecreator - Running Network Magic version -5.5..9195.0-Pure0 on Windows XP Home Edition SP 3
Running Network Magic version -5.5.9195.0-Pure0 on Wireless Computer with McAfee Personal Firewall Build 11.5.131 Wireless Computer has D-Link DWA-552 connecting to D-Link DIR-655 A3 Router.

Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution?

Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution? (No jailbreak)
Most of the time the iphone cannot reach any network and when it can, there is no data transfer, I can only make calls and sms.

Skizofrenias wrote:
Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution? (No jailbreak)
Most of the time the iphone cannot reach any network and when it can, there is no data transfer, I can only make calls and sms.
iOS: Troubleshooting Wi-Fi networks and connections
iOS: Wi-Fi or Bluetooth settings grayed out or dim

Both xp and windows 7 have video problems with my VGA connection using TV

both xp and windows 7 have video problems with my VGA connection using TV as my monitor when it gets to starting up windows no matter what version it will not I have let my mac on all night and still says starting windows or the windows 7 logo and nothing else will happen also when I use a 3rd patty software like peraills or other it works like a charm how to fix it?

To map the drive on your computer click on Start - RUN - type "\\192.168.1.1" and click ok... When prompted for Username and Password type "admin" and click ok... Now you will be able to see the folder which you have shared on your router, right click on it and select "Map network drive" and click on finish.
Now it will map the drive on your computer and you should be able to transfer the file from your computer to the USB drive.

Hi, recently purchased macbook 13", I have problem with sound when connect to my LG Smart tv with sound system. When i change sounds effect on my sound system also LG its all go quiet didn't have this problem with my laptop. Any advise ?

Hi, recently purchased macbook 13", I have problem with sound when connect to my LG Smart tv with sound system. When i change sounds effect on my sound system also LG its all go quiet didn't have this problem with my laptop. Any advise ?

Some progess I see. To be honest, i would not waste your time with trying to connect using wireless.
You are likely to get poor connections and dropping out.
If its working using a cable, then there is no need to bother with giving me the network settings, bu see how it goes, because sometimes giving the TV a static IP address can give better results.
There is an example of a couple of powerline adapters on the diagram below. Just ignore the network switch unless you want to connect other devices which are near to the TV.
http://forumhelp.dyndns.info/networking/powerline3.jpg
I will monitor the subject line of this thread, should you want to post any more information.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Has Apple fixed the problem with 4G cellular connection?

Has Apple fixed the problem with 4G cellular connection on the iPad 3?

Cellular connection problem was for US connection in Houston, Texas. Have an iPad 2 which functions perfectely on Wi-Fi or 3G. Bought an iPad 3 strictly to get the increased speed from the 4G LTE connection. Purchased on with the AT &T cellular. Wi-Fi functions fine, but 4G LTE connection is terrible when it connects at all. Went to AT&T and they said no problems with service in my area, but never get over 2 bars and most times, Web pages load very slow or will hang and not load at all. Went to the Apple store and they said it was AT&T network problem and went to AT&T and they said no problems with their service. Went to the Apple communities forum here and discovered that many people were having the same problems with the 4G LTE cellular connection on their iPad 3's. Didn't seem to matter if it was AT&T or Verizon. So I decided that I would just return the unit and wait for Apple to fix the problem. Hence my question.
Appreciate very much your time in responding to my question.

Facing problems with network due which the phone goes into hangs status

Facing problems with network due which the phone goes into hangs status. some one help me with switching between 2g and 3G network

Hi Mani Nair,
I apologize, I'm a bit unclear on the exact nature of the issue you are describing. If you are talking about having issues with a 3G cellular data network, you may find the troubleshooting steps outlined in the following article helpful:
iPhone cellular data connection issues
Regards,
- Brenden

Organizer elements 11. Problem with your internet connection

I am trying to access facebook and Flickr via the Organizer with elements 11. I went to preferences and cleared the oline services, when I try to refresh the partner services I am greeted with the error " there is a problem with your internet connection, check your firewall settings" .
Windows 8, updated. I tried disabling the firewall. I have also tried making sure permissions are set up to allow all adobe products access through the frewall when it is enabled. No other network managment services or virus scanners installed. just default 64bit windows 8.
I am currently left with no partner services; facebook, flicker, picasa, etc.... I could reinstall organizer i guess to get the default services back...
I found discussions on the web but none with a solution. http://forums.adobe.com/message/4035670
Any help would be great

I apologize for the delay. An update was released shortly after I posted the question that resolved the issue. Thank you for your assistance though. As soon as I read your advice I went to my laptop to follow your instructions. Upon opening photoshop I was prompted with an adobe update message. After the update the issue was resolved. Again, sorry for not updating the situation.

I have an iPad MD371Y. Since when I installed the iOS 6 I'm fading problem with the WiFi connection. The line fall everytime the device go on automatic stand by (if i do not touch it for 5 min). Can somebody be of Help?

I have an iPad MD371Y. Since when I installed the iOS 6 I'm fading problem with the WiFi connection. The line fall everytime the device go on automatic stand by (if i do not touch it for 5 min). Can somebody be of Help?

iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting
http://www.apple.com/support/ipad/wifi/
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Problem with Network Magic/Connecting to my PS3

Similar Messages

Maybe you are looking for