Problem with new build, Motherboard/Case

Hi, I bought a new pc that arrived Friday, It is my first build so bare with me on some bits.
But to cut it short I have the NZXT Phantom case with a P67A-GD53 Motherboard, And when I screw it all down to the case I cannot fit my GPU in (GTX 570 Power Edition) It gets blocked by the PCI slots at the back, And at first I didnt have my I/O Shield on, But took it off and instaled that and now the motherboard physically cannot screw in at the top without me bending the board..Do I have a dodgy case, Am I installing wrong or just missing the obvious like a moron ?
Any help much appreciated

Quote from: smify123 on 02-October-11, 18:21:46
or just missing the obvious like a moron ?
Turns out this was the answer -_- I just didnt have the stand off screws installed lol

Similar Messages

  • Power on-off-on Problems with New Build Z68A-GD65(G3)

    I'm hoping someone has seen these issues and can help me, although I realize this is a vague issue. I'm working on a new build. On power up everything looks good but then I get a power off and back on (like a reset). Sometimes it happens very quickly; other times it will stay on for roughly 5-10 minutes before the reset. I've checked all the connectors, case wires look ok, BIOS info looks correct.
    The other issue is that when I tried to do the Win 7 install, it loads the files, goes to the "Starting Windows" screen, and freezes there (until the next power off problem shuts things down).
    Any ideas on what to try to narrow things down?  Seems like it almost has to be the power supply or motherboard? 

    Quote from: Henry on 28-October-11, 09:54:40
    You have more than a Z68A-GD65(G3), please list he rest of your components. See my signature below for example of what to list.
           >> Posting Guide <<
    I've disconnected everything but the mouse, keyboard and monitor and still have the power resets.
    Tried one memory module at a time... still fails.
    Played with lower memory freq settings... still fails.
    Finally pulled the MB out, bench tested it to rule out shorting in the case; tried it with and without other peripherals... still fails.
    I think I'll RMA the MB, although I suppose it could be the psu (unlikely, I'd think).
    I had two bad motherboards in my last build. I had hope that MSI would be better... 

  • Problem with Weblogic Builder SP1

    I have a problem with Weblogic Builder SP1. I basically re-used my EJB deployment
    descriptors from WL5.1 in WL8.1. Before SP1, i have no problem loading my EJB
    in WB. But with SP1, WB throws weblogic.marathon.model.LoadFailureException.
    I re-attempted by jarring my EJB with WL5.1 descriptors and used my friend's WB
    (not SP1) to export new descriptors which I used to re-jar. This new EJB is again
    not recognised by WB SP1?
    What is wrong?

    The exception is as follows:
    Opening module myproj.jar
    java.lang.NullPointerException
         at java.util.Arrays.sort(Arrays.java:1181)
         at weblogic.marathon.model.EJBJarCMBean.initRelations(EJBJarCMBean.java:1212)
         at weblogic.marathon.model.EJBJarCMBean.initBeans(EJBJarCMBean.java:1098)
         at weblogic.marathon.model.EJBJarCMBean.setup(EJBJarCMBean.java:1144)
         at weblogic.marathon.tasks.OpenModuleTask.getEJBModule(OpenModuleTask.java:156)
         at weblogic.marathon.tasks.OpenModuleTask.figureOutModule(OpenModuleTask.java:191)
         at weblogic.marathon.tasks.OpenModuleTask.figureOutModule(OpenModuleTask.java:230)
         at weblogic.marathon.tasks.OpenModuleTask.runBackground(OpenModuleTask.java:89)
         at weblogic.tools.jellybeans.core.task.TaskThread.execute(TaskThread.java:127)
         at weblogic.tools.jellybeans.core.task.TaskThread.run(TaskThread.java:64)
    Module myproj.jar descriptors failed to load
    The EJB has no problem deploying.
    Rob Woollen <[email protected]> wrote:
    You'll have to at least show us the error you get from marathon.
    Does your application deploy to the server?
    -- Rob
    Robin Tan wrote:
    I have a problem with Weblogic Builder SP1. I basically re-used myEJB deployment
    descriptors from WL5.1 in WL8.1. Before SP1, i have no problem loadingmy EJB
    in WB. But with SP1, WB throws weblogic.marathon.model.LoadFailureException.
    I re-attempted by jarring my EJB with WL5.1 descriptors and used myfriend's WB
    (not SP1) to export new descriptors which I used to re-jar. This newEJB is again
    not recognised by WB SP1?
    What is wrong?

  • Problem with Folio Builder - added articles are "spinning"

    Hello,
    today we are experiencing strange problems with Folio Builder. We are adding new artcles to folio created today and all added articles have same issue - spinning wheel in folio builder. Such articles we can't see in Content viewer until we delete existing folio.
    Thanks for help

    Hi,
    Could be that there was a network problem when uploading the InDesign documents.
    Try to select the articles and delete them with the trashcan. And then reupload the documents from InDesign.
    Good luck!

  • Problem with new version 4.3.2 apps not working " after update to the new version "

    Problem with new version 4.3.2 apps not working " after update to the new version "
    i was in 4.3.1 then i do the update , but now after update i face this problem , so what i Supposed to do ?!!

    Hi There
    Had the same problem as you. App would terminate when launched.
    Solution to working You Tube app:
    -Go to playstore
    - Uninstall app (it doesn't remove the app, only removes the update)
    - "Et Voila", working again.
    This doesn't correct the problem, it's just a workaround for you to be able to use youtube app again.
    Hope it helped.
    Best Regards

  • I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add

    I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add APN. Now when i switch to safari its showing you are not subscribed for cellular data. But I am able to use data on other phone.
    Will you please help me in this regard?
    Another issue, since i bought my new iphone there is dust inside back main camera.
    Your advises are highly appreciated.

    Hey Shaiju isac,
    I'd take a look at the following article, it'll guide you though steps to you troubleshoot cellular data issues on your iPhone:
    iPhone: Troubleshooting a cellular data connection
    http://support.apple.com/kb/ts3780
    Cheers,
    David

  • Wifi problems with new ipad

    I'm trying to learn how to correct wifi problems with new iPad.  It is the wifi only, 64GB model.  I want to be able to use it at work, where we have a great wifi network.  I can usually connect to our network with no problem, but after an hour or so my iPad loses the network.  When I try to reconnect, I see that the network is showing full strength reception, but I get the error message from the iPad that I am "Unable to join" the network.  My iPhone connects to the same network seamlessly, as do all of the other iPhones of my co-workers and the older generation iPads that some of our staff has.
    At other locations, I typically have no problems (home, apple store, etc.) but I have had the same situation pop up at a coffee shop where I could see that there was a wifi network available, but I could not join it even though it was the shop's free wifi. 
    I have tried turning the iPad off, turning off wifi and turning it back on again, and forgetting the wifi network in question.  I can't think of any other methods that are available to an end user to correct the problem. 
    I have already gone to the Apple store to swap out the unit, and the newer one is having the same symptoms. 
    Can anyone offer any advice here?  This is quite frustrating.

    No problem! Have a read at this most interesting article which has special significance as regards your models!
    http://edition.cnn.com/2012/04/05/tech/gaming-gadgets/ipad-wi-fi-issues/index.ht ml
    However, I attach an extract from another thread for your perusal. You can disregard any suggestions/links you have already explored -
    created by Texas Mac Man in Using iPad - View the full discussion
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router &amp; then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
     Cheers, Tom ;)

  • List of Problems with new Web Mail

    List of Problems with NEW Web Mail :
    - At first doesn't open full page message list or retain full page as default setting, have to drag down bar
    - Only shows 20 message lines after “pulling down” the divider, screen partially empty until I scroll down.  It should show at least 26, preferably all available
    - After moving bar, bar moves back up after going back to inbox (not delete message) after reading a message, have to move it down again, and again...
    - Doesn't go to next message when delete message on screen is selected, no setting option for default to do this.
    - There is a drop down to select which folder to move a selected email to.  The initial display shows 7 usable choices, with the usual slider and arrow to show more choices.  The space on the slider clearly shows more choices are present (actually about 20 or so are there), but any attempt to use the slider or arrow to see more choices causes the drop-down to instantly disappear.  I can't move the selected field with arrow keys either.  I can select any of the visible 7 choices, and move an email to only one of the 7.  NOTE: This one works in both IE and Firefox, but if Verizon Webmail was fully web standard (see http://en.wikipedia.org/wiki/Web_standards) compliant it would also work in my preferred browser, Mozilla Seamonkey, the direct descendant of the original Mozilla browser.  Webmail should be FULLY web standard.
    - Occasionally a message will move from inbox to trash, without NO indication or command to move them.
    - Emails occasionally flash an error message and simply disappear - not to trash or other findable place, just disappear.  No time to read the error message either.
    - No way to set a whitelist for supposed spam emails, unless the whitelist for “Blocking” is the same.  Very unclear.
    - How can I switch my service back to the original, basic, email which works ok?  I know it’s still there, since some of my other accounts still access it!!!
    This seems my only way of getting this info direclty to the programming staff.  If it doesn't actually do this, will SOMEONE PLEASE FORWARD THIS MESSAGE TO THEM !?!  
    Thanks!

    vz_ric wrote:
    The majority of websites are set up the same way for all browsers. It's the software manufacturers responsibility to make their software compatible with websites, not the other way around. Otherwise everyone who has a website will have to make 10 different sites to work multiple browsers.
    Contrarily, it is Verizon's, as well as other companies like Verizon whose customer base uses a wide variety of web browsers, web page designers' responsibility to use only standard W3C-recognized code and not to use non-standard non-W3C-recognized code, e.g., Microsoft's Internet Explorer specific code, when designing their web pages. In my opinion based on my observations, Verizon's web page designers are too often guilty of using IE-specific code.

  • Adobe aftereffects is not working on os x maverics all updates...... is dis soft. will work on the new os x yosemite.??  y apple is nt working on dis problem wen users are facing problems with new os x .....

    Adobe aftereffects is not working on os x maverics all updates...... is dis soft. will work on the new os x yosemite.??  y apple is nt working on dis problem wen users are facing problems with new os x .....

    I suggest you contact Adobe tech support or their Mac forums for assistance.

  • Reposting this If your having problems with new Windows 8.1 do a full uninstall of all Apple

    Reposting this If your having problems with new Windows 8.1 do a full uninstall of all Apple iTunes programs but uninstall them in right order and then do restart of computer then reinstall newest iTunes and it will all be fixed up syncing problems or other problems this is thanks to Apple phone support

    What is your technical support question for these user to user technical support forums?

  • Strange problem with my build JAR

    Hiii everybody... I'm having a strange problem with my build (JAR file)... when I work with the Eclipse and I click in the table that returns the clients stored in my PostGre database it works fine, but when I build my application and it generates my JAR file and I open it and click in the same table to return the objects that I have.. it does not appears anymore.. just show when I work with eclipse... and the database is the same for both.
    I already checked the database path in my properties file... and the application recognize the database because I can login and there isn't any runtime exception...
    In that application I work with Hibernate and Spring... for me it is very strange because the application works fine when I run by eclipse... but does not return the database data when I click on my Jar file to open the application..
    Someone can help me with that?
    I dont know if the problem is in the Spring, Hibernate, Libraries...
    thanks in advance...

    So what's the error then? Are there any error messages? Have you checked the console? Or are you just clicking on the jar and you wouldn't even see the errors if there are any?
    What do the logs say?
    You're not giving a lot to work on here.

  • When Apple solve problems with new iTunes calendar sync with windows and outlook?

    When Apple solve problems with new iTunes calendar sync with windows and outlook?

    Anything Downloaded with a Particular Apple ID is tied to that Apple ID and Cannot be Merged or Transferred to a Different Apple ID
    More Info here...
    Apple ID FAQs  >  http://support.apple.com/kb/HT5622
    If necessary...
    Contact iTunes Customer Service and request assistance
    Use this Link  >  Apple  Support  iTunes Store  Contact

  • Before I buy has there been any problems with new 27 iMacs?

    Before I spend my hard earned cash does anyone know if there has been any problems with new 27 iMacs?

    Hello richard from Folsom:
    Are you inside or outside?  (  I could not resist, I lived in Sactown).
    Anyway, advice is frequently worth what you pay for it, and mine is free.
    If you want it, buy it.  The posts above are right on the mark (except waiting is probably overly-cautious).  The best advice (from anamusic) is to buy the extended warranty - well worth the money.
    Barry 

  • I just started using my iphone 5s. I have a problem with new incoming emails from my POP account. Why are they marked as read automatically even though I have not even opened them yet.

    I just started using my iphone 5s. I have a problem with new incoming emails from my POP account. Why are they marked as read automatically even though I have not even opened them yet.
    At first I thought it might be because I was using simultaneously my old iPhone 4S so it somehow realized the emails where being pushed to another device and the it marked as read, this has nothing to do since I have deleted the email account from the iPhone 4S

    Contact the email provider for assistance with their service.

  • Premiere Elements 13 , Problems with new text/titles

    Premiere Elements 13, bisher keine Probleme. Nachdem die Filmlänge etwa 15 Minuten beträgt immer größere Probleme Titel/texte einzugeben. Wartezeiten sind extrem lange oder Programm stürzt ganz ab.

    High ATR,
    Computer running on Widows 7 ,64 Bit System, Service Pack 1, Processor AMD Phenom(tm) X4 945 3.00 Ghz;RAM 8 GB
    Grafikkarte: NVIDIA GeForce 8800 GT
    If the video on the timeline is longer than 10 minutes the problem will be remarkable. The response times adding a title is getting longer(2-15 seconds).
    As the video is now 18 minutes the response time is after each action(resizing of letters or any changes of the text) up to 30 seconds or the program crashes completely.
    Project settings are the following:
    General HD 1080i; 29,97frames/second; Video:1920v 1080 H, 30 fps
    Video: maximale Bittiefe, Dateiformat i-frame only mpeg, Kompressor MPRG i-Frame, Standbilder optimieren
    The video is a mixture  of full HD videos 1920x 1080 .mov and pictures up to 4608x3456 pixels.
    When the program crashes I remarked that the main memory RAM(8Gb) was fully used by the premiere program. Might there be a problem?
    Thank you for your service.
    thomasd
    Von: A.T. Romano 
    Gesendet: Sonntag, 1. Februar 2015 23:55
    An: Thomas Deschler
    Betreff:  Premiere Elements 13 , Problems with new text/titles
    Premiere Elements 13 , Problems with new text/titles
    created by A.T. Romano <https://forums.adobe.com/people/A.T.+Romano>  in Premiere Elements - View the full discussion <https://forums.adobe.com/message/7151822#7151822>

Maybe you are looking for