Problem with PT8 NEO Y VGA ATI SAPHIRE 9250SE

problem with PT8 NEO Y VGA ATI SAPHIRE 9250SE

From the VGA test report: http://www.msi.com.tw/html/products/mainboard/testreport_pdf/6799/vga.pdf for the board , i can't find ATI Radeon 9250SE , but it is obvious that MSI only tested their Nvidia cards and no ATI cards. So, you'd better to try Nvidia cards or contact your VGA vendor to ask if there is the latest VGA BIOS to solve your issue.
Anyway, remember to tell us the results .

Similar Messages

Problem with repaired neo fis2r

I am experiencing performance problems with my neo tha t I am not sure where to begin trouble shooting. I had an video card falure(delaminated pin on agp ) which resulted in damage to the agp slot I rma 'd my neo and it returned marked repaired with a grey agp slot , bios 1.4 ( had 1.6 installed) and the same serial #. I reinstalled all components. noted the retrograde bios and flashed to 1.8. then I attempted to return all settings to theyre original state only to find that I can't overclock! previously I got 250mhz clock with perf mode set to ultra turbo and ram set to 333mhz . now I can't get past perf mode fast and 205mhz no matter what. I see references to bios 1.8 as being not very overclockable.this may be the problem but the waters have been muddied by the multitude of events. I am not an expert and do not know where to start. I was so thrilled with the performance of my neo and now I am at a loss . Is the bios responsible for this abysmal performance or is my system still compromised? I don't know what to do to determine its state. my system is as follows:-
neo fis2r( of course)
2.4c p4 with zalman alcu 7000
ati 8500dv
512mb samsung 400mhz ram
seagate barracuda sata 150 raid 0
pci modem card
thermaltake xaser2 case
any suggestions would be greatly appreciated
kev

essentially I am not just concerned about it's current inability to overclock. but more in the fact that b4 the repiar of the board I was able to overclock with no difficulty and no special considerations. in fact when I look at my little log of bios settings the agp clock was set at 66.6/33.3 after all the overclocking. and now with EXACTLY the same components( ati card repalced but physically identical) none of those same settings work. did the failure damage other components whose failure is not yet critical path or has the bios upgrade caused instability?

Display problems with K8N Neo Platinum

I have XP Professional installed on my Raptor fine, but I am having issues with my Radeon 9800. I cannot boot XP unless I hit F8 and then select "Enable VGA Mode"
When I do not enable VGA mode, my monitor goes blank right before the Welcome screen.
Moving along...now when I boot with "Enable VGA Mode" I cannot change ANY monitor settings. If I increase the resolution from 640x480/8bit to, let's say, 800x600/32bit, the screen will go blank for a few seconds and then a black screen with a white blinking cursor at the top left corner will show. After this, my monitor just completely shuts off and I am forced to restart.
I also had problems with the ATi Control Panel. The ATi driver package installed fine, so I rebooted but when Windows started, I received an error message saying that ATi Control Panel could not load.
I'm baffled right now and I really don't know what to do. Any help is appreciated, thank you guys very much.

You might want to try and reinstall the video drivers and make sure that you uninstalled the old ones fully with Driver Cleaner.

Problems with K8T Neo-FSR (ms-6702) and radeon 9800

hey
does anybody have problems or success using an ati radeon 9800 graphics card with this board?
any special configurations required ?
seems that other msi neo boards cause problems with this card

Make sure to use the VIA drivers that came with the board as the newer Hyperions do not work as well and have been known to cause issues.

Help! XP install problems with K8T Neo-FIS2R

The other day I put together a new system for a friend. I got the system to POST properly, the diagnostic lights on the D bracket are fine, and I can edit the BIOS, and the BIOS sees all the drives properly.
However, installing XP Pro has been impossible. I set the system to boot first to the CD, then to the hard drive (from the BIOS). After booting to the CD, I never see the message I am used to seeing ("Press any key to boot from CD...) when booting from the XP Pro install disk. The system thinks about things for a long time with a blank screen, then later it finally begins to do the install. Things appear normal at this point as in any other time I have installed XP Pro. I reformat the hard drive to start clean and then the XP install files are copied over. I get the standard message that the system will reboot and this is where things get flaky. The system reboots, but I never get the message once again on whether or not to boot from the CD. So after a while the system tries to install XP once again (it would repeat this process forever....trust me). I've popped the CD out right after the system reboots so it will try to go to the hard drive. I just get some kind of boot failure message and to insert the bootable media or whatever. I've even gone into the BIOS right after the reboot to switch the BIOS loading to try and load the hard drive first. This still doesn't give me the desired results.
This is by far the weirdest thing I've ever experienced when doing an install. I've installed XP Pro on at least 15-20 desktops/laptops of different configs and never ran into this before.
The BIOS settings are stock. I didn't see anything in there that was really needed tweaking or that hadn't "set itself". I haven't messed with the SATA or RAID stuff since it's not really necessary in this situation.
Here are the system specs:
--Antec 430 True Power PSU
--K8T Neo-FIS2R mobo
--AMD 3000+ 64 bit CPU
--40GB Maxtor HD (master on IDE1)
--Lite-On DVD-ROM drive (slave on IDE1)
--80GB Western Digital (8MB buffer) (master on IDE2)
--Sony DRU510A DVD-RW (slave on IDE2)
--(2) Kingmax 184 Pin 512MB DDR PC-3200 Model# MPXC22D-38
--ATI 9800 Pro
--3.5 Floppy
All the components except the mobo, CPU, and memory are from another AMD system that was running fine. No problems with any of the HD's or the optical drives. All new components were purchased from newegg.
I thought that maybe I had a problem with the jumpering of the drives so I messed with those in about every possible combination. I took IDE2 completely out of the system and just tried to get it running with the 40GB Maxtor and the Lite-On drive. I tried about every master/slave/cable select combination but nothing was working. In certain combinations the BIOS recognized everything as I intended. I've pulled everything off that doesn't need to be connected. Keyboard, monitor, and internal components are the only things connected.
I don't consider myself to be a guru at this business, but I can get through most things with enough trial and error. This really has me stumped.
Any help is certainly appreciated.
Thanks,
Heath

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Download the drivers from MSI again, and when you copy the contents of the XP folder to floppy ADD the file txtsetup.oem from the directory above that folder. Worked for me..!
Ian

Boot Problem with K8n Neo 2 Platinum

I cant get my Computer to load the bios
Sometimes when I restart my computer it will lock up in the Bios Sign on and the only way to get it to boot through is to keep resetting the computer and turning the power off and on. It does this on a random basis, Ive also had problems with it locking up if the dynamic oc is turned on.
Has anybody heard of this happening or know how to fix it?
MSI K8N Neo 2 Platinum Bios 1.4
Athlon64 3800+
TwinX 1024 3200LLPRO
Xtasy 9600XT
Ultra Products X-Connect 500w
2x WD Raptor 10,000rpm SATA HD in Raid 0 cfg
SB audigy 2 ZS
LiteOn cd/dvd drive
LiteOn dvd burner
Windows XP SP2

Corsair memory is known to be troublesome with AMD64.
Nevertheless, if everything is set correctly, it'll work. I've been running the LLPRO 3200 1GB kit at 220MHz without any noticable problems. Run a couple of rounds with Memtest86+ to verify memory functionality.
Can you please give your specifications on the power supply unit (PSU), especially the amperage on the +12 volt rail.
Anders.

Problem with K8N Neo 4 Platinum

Hi I am new on this forum.
I have problem with proper configuration of the BIOS in K8N Neo 4 Platinum. My processor is Athlon 64 3000. It has 1800 clock. My BIOS makes default 200MHz x 5. It makes 1000 MHz clock. Will it be good if I change at 200 x 9?
Other thing: I tried to change at 200 x 9 but in Windows (2000) is still 200 x 5 (acc. to Core Cell). When I chanded on 200 x 7,5 all in Windows was ok. Core Cell showed 200 x 7,5. How I may resolve this problem?

Quote
I have my memory in green slots. Does dual channel works in this case?
- No Green = Channel A, Purple =Chanel B use Green nearest cpu & adjacent purple slot.
Quote
HT freq. 5x
That's your HT multiplier as mentioned by Some1ne not the Adjust CPU Ratio which is the CPU multiplier.
Your CPU is running at the correct speed.
DDR Clock: 167 MHz s/be 200 - this should chnge when memory is in right slots.
Change memory over & let's have a look @ those settings then.
luck

D-BRacket 2 and keyboard cordless problem with k8n neo platinum

hi
i have two problems
the d-bracket2 doesn't work
when my game controller is on , it isn't recognized by Win XP
but the 4 leds are green.
i tried the two connectors and it's the same thing.
my logitech cordless keyboard doesn't work in the bios
i tried with the ps2 but the keyboard didn't work in XP
i check the bios with an other keyboard and the usb keyboard support is enabled
can you help me ?
PS: Sorry for my english

Hi galette,
Do you have a k8n neo or neo2 ?
At least some neo2's have problems with ps/2 keyboards. Their users could circumvent this by using usb keyboards.
I have a logitech cordless desktop myself and for me it works. Perhaps you can borrow a usb keyboard to test it ?
vanish

Strange problem with P35 Neo

Hi there.
Got a strange problem with a computer that got a P35 Neo system board.
The problem I got, is that the computer don't boot. If I reset the CMOS,
I can get the computer to boot, but then it hungs on loading Vista.
Then I try to repair my Vista. Then the computer hungs while loading the DVD.
I have tried to boot with only one RAM in the computer, but the problem still
there...
I have tried to reset the CMOS by changing the JPBAT (I think it called so) jumper
and to pull out the battery.
I have tried to disconnect all, but one HDD and but I can't say that it worked any
better...
Any ideas how to find out the error?
2 x 2 GB Corsair RAM
Intel dual Core CPU
Radeon 1950 PCI-E
1 Samsung SATA HDD
2 Seagate SATA HDD

Quote from: BOSSKILLER on 25-August-08, 20:31:15
What PSU you have? Corsair Powersupply 550W Black, ATX/EPS
Provide better details about memory sticks used. Corsair TWIN2X 6400C4DHX DDR2
What CPU? Intel Core 2 Quad Q6600 2.4 GHz
BIOS version onboard? Note sure, since I'm not right at the computer for the moment. But I think it's 1.0 since it is brand new from store.
Do memory check with >>Memtest86<< Well, it's kind of difficult, since the computer dont boot.

Overclocking problem with P965 NEO

Hi, i actually have a problem with cpu and memory.
my settings are:
MSI P965 NEO
2x 1Gb Gskill DDR2 800Mhz 4-4-3-5 2.0v
Core2duo e6300
zalman 9500CPN
i want to overclock the micro, and set the ram to the proper timigns, if i set all to auto, and the FSB to 300Mhz, the ddr speed raises to 473Mhz, and it's not what i like, i just want to reach a 1:1 FSB ratio and increase only cpu FSB not RAM fsb.
Here i dont have the FSB:DRAM ratio, like i used to have in my asus.
Ok, going to the point, i want to know how to increase cpu fsb and not the ram mhz. and also put the ram to the full spec.
the ram is at AUTO and the speed manually to 667 because the problems i found with CPU-Z.
The SPD reports 400Mhz, 4-4-3-5-24(trc)-2T
Thanks,
Ariel

Quote from: pszemia on 23-May-07, 01:22:26
i want to overclock the cpu without overclocking the ram, is that possible with this motherboard??
for example: 333Mhz cpu and stay at 800Mhz for ram
the cpuz is reading actually 379 (i cant remember the exact value, but is around this) for ram when i have set to manual 667 why this happen??? (the cpu is at 300)
The memory speeds you can select are not absolute but FSB:RAM dividers
533Mhz equals the 1:1 divider
667Mhz equals the 4:5 divider
800Mhz equals the 2:3 divider
This means if you select 667Mhz RAM in bios you don't force 667Mhz but you select a FSB:RAM ratio of 4:5
At stock FSB of 266Mhz this makes : 266 / 4 = 66.5 * 5 = 333 Mhz (666 Mhz DDR) wich is the 667Mhz you select.
However, if you change FSB the RAM speed changes along with it.
So, for your 300Mhz this makes : 300 / 4 = 75 * 5 = 375 Mhz wich is +- the 379 Mhz cpuZ reads.
If you want 333Mhz fsb and ram @ 800 select 667Mhz RAM in bios and set FSB to 333Mhz, also enter RAM timings manually.
This will result in 333 / 4 = 83.25 * 5 = 416 Mhz (832 Mhz DDR) for ram - The gskill should be able to take this mild 32Mhz overclock.
The board might not make it to 333Mhz tho - It's a budget board wich overclocks poorly.

Weird problem with k8n neo fsr

hello!
i have weird problem with my K8N Neo-fsr and Athlon 64 2800+ socket 754, when i try to overclock i change in bios HT from 4 to 3 (for better stability), after restart nothing happen, my pc wont boot, also nothing on screen, so i must clear cmos for solve my problem and set to 4 i try several bioses from official to moded also pinochio`s and syar`s moded and allways the same issue is it problem with processor? or motherboard?
thanx for your help and sorry for my english

You should first get down cpu ratio, then get up cpu fsb and as you wanted set ht frequency from 4 to 3 and "save changes and exit" if it doesn't boot change you psu (at least antec 380 or tagan) or go fast to send back your mobo to reseller!!

Boot problems with K8N Neo FSR

Recently i bought a new MSI K8N Neo FSR mainboard and an Athlon64 3000+
I noticed that a lot of people on this board had problems when booting Windows XP
I had the same problem: Every time i tried to boot Win, it freezed at the Win XP logo.
It seems that the problem is my cordless logitech keyboard.
When i'm using a standard PS/2 keyboard i have no problems booting.
Are there any known problems with nForce3 based mainboards and cordless logitech keyboards?
Does anyone know if there is a way to fix this problem?

There just seems a problem with some mobos and keyboards.
Usually it's a PS2 thing, but looks like you have found another to add to the list.
Note...
COMPATIBLE INPUT DEVICES (Keyboards)
Aspire/Mitsuko Internet Keyboard
Cherry Soft Touch
Chicony #KB-9805
Compaq EVO Series
CoolerMaster Q
Dell
Logitech Cordless Duo, Logitech Ultra-X, Logitech Internet Navigator
Logitech Di Novo Series
Memorex Multimedia
Microsoft Multimedia Wireless, Microsoft Desktop Elite
Mitsumi #KFKEB9HY
Qtronix Scorpius
Viewmate Office

Going on week FOUR of problems with MSI NEO-2-S :/

Mainboard: MSI Neo2-S, BIOS Rev. 1.5x (whatever Live Update sent me)
RAM: GeiL 1GB (512x2) PC-3500 Matched pairs
CPU: P4-2.4c
HD: WD 1200JB Special edition
Cooling: Stock intel, lapped @ 800 grit
PSU: 450W
Video: MSI Geforce 4 TI-4200 64MB
O/S: Windows XP Pro SP1A, IE 6.x latest security patches
DX: Direct-X 9b
BIOS setting: Slow
Overclocking: No, system will not even run stable at rated speeds.
Problem:
System just shuts itself down in the middle of gaming.
CPU temperature has a wide range, depending on how cool the night is and if I have my windows open etc the system can be as low as 40c. Under load while gaming I've seen it go to between 59c-62c.
I've gone into Core Center and turned off the dynamic overclocking so it doesn't adjust speed in the middle of playing games, thinking that might be causing issues.
I've also cranked the fans up all the way in Core Center to increase cooling.
Heck I've even turned Core Center OFF thinking it was messing with my system.
No antivirus is running in the background while I'm gaming. I've fresh installed XP Pro. I've re-applied service packs.
I'm worried about the temperature but I don't necessarily know for certain the sudden shutdowns are a cooling issue.
I am going on week FOUR of problems with this new system. I have never purchased an MSI mainboard and seriously, I have just flat out had it. I've already been through one RMA'd board, I am not RMAing another. I have 3 days left on my newegg account before I am stuck with this MSI, forever. If I can't find a solution ASAP (in 24 hours!) I am returning this MSI board and getting a Gigabyte 8KNXP.
Can anyone help me out here with suggestions please. I'm at my wits end. I've never had to do SO MUCH WORK to get a system running stable. I put my P3 with Intel mainboard together 2.5 years ago and I haven't had ONE single issue.
Stability is a BIG factor for me. I can't even think about overclocking when this sytem won't run at rated speeds!
Chris

This is a different problem.. the first board just flat out died after upgrading the BIOS. I never even got to use it.
This new board upgraded the BIOS just fine but I've been experiencing crashes and shutdowns.
I don't have any spare motherboard or CPU to test it in, and if I did I'd still have to run it for several days..and I don't have several days due in part to me having to dink around with it for so long.
I would say I am in game for 30-60 minutes before I see temperatures that high. Although again I have been playing this same game on my P3-1ghz with the same Video card and never once had a shutdown like this. Never once overheated.
I have all the fancy display/graphics options turned off..I have tested in different resolutions (it makes no difference temperature wise)
I do not know what my core temps are, I can check when I get home and post them if it helps.
I'm running everything at stock speeds. I've noticed Core Center ups my speed slowly from 201x4 to 203x4 etc and so I disabled that and finally flat out took Core Center out of startup. I didn't want it modifying anything while I was playing on the chance it was causing the crashes. Still no change even after that.
The temp does seem a bit high, but I have lapped the heatsink and fan and applied a layer of termal paste (silicon based) to both the HSF and the CPU. I removed that old black pad by scraping it off and then cleaning it with some xylene based carburetor cleaner. I spent several minutes rubbing the black melted parrafin goo off the processor and HSF with a coffee filter. I'm very confident there was little to none left when I applied the new thermal paste.
I don't understand why it runs so hot, nothing is overclocked, I'm running low settings in the game. These temps i'm posting are from Core Center. I have the case OPEN (plenty of ventilation) and I have the windows in my room open to the night air!! (i live in san diego, its cool at night right now) I tried with the case closed also just to be sure and I received the same temperature readings.
None of this makes sense...and after 4 weeks and 500 dollars I'm tired of having to make it sense. It should work right away and that's that.

Problem with Serial Number from MSi ATi HD4870 :/

Hi all,
I have problem with my HD4870. I lost the serial number (the small paper on back of card) from card. Have I any chance to get it back? I can take a photo and post it here some S/N and P/N from card, if it helpfull... I lose my warranty, if I can't get it back
So, any choice to get it?
Thanks for answers,
Mirek.

Thanks for answers in first,
I have problem with card - I had it two days in Crossfire with another HD4870 but accidentally when I played Metro 2033 I got some stripes on monitor (purple, blue) and then PC stop working. I had to restart PC and when the system booted to Windows, until 10 second I got the same stripes on monitor. Then my PC didn't boot.
On my card I have 4 diodes - when I turned on pc, the diodes blinks but now blinks only TREE of FOUR diods.. So I took the card to shop when I bought it, but the shop-assistant told me, that I need this little paper on Card.. :/
I'm from Czech Republic, so I have a little problem with directly contact to HQ of MSI
So I have to go again to the shop and tell them, that Serial Numbers what they need are in card?

Cool & Quiet Problem with K8N Neo Platinum

Hi!
I just formatted my windows xp and encountered weird problem with Cool & Quiet.
Before the format CQ worked perfectly, but now when I apply minimal power management from the properties Windows freezes.
I have 1.2.2.2 drivers installed and CQ enabled from BIOS.
BIOS has been updated to 1.7, 1.9 bugged for me.
Windows XP SP2 + all hotfixes.

Quote from: aicjofs on 09-October-05, 02:49:29
If all he has done is "reformat" windows what would have changed in the BIOS magically? Still seems like the driver to me...Troubleshoot what has obviously changed since things worked normally. If he didn't touch the BIOS and only reinstalled Windows the driver is the logical issue.
Ugh...even in that linked article the guy is saying the HyperTransport is the link between the CPU and Chipset/RAM. There goes this RAM thing again. The memory controller communicates with the DRAM controller no Hypertransport about it...
ok, but where is DRAM controller? in CPU my friend and in Athlon 64 is DRAM controller in CPU so this is HyperTransport - comunication with CPU and memory...no only me has this mention but also another guy and another, so all of us are wrong yout think?

Problem with PT8 NEO Y VGA ATI SAPHIRE 9250SE

Similar Messages

Maybe you are looking for