Problem with reset SMC
hello guys .. i have problem by resetting the smc in yosemite system . ... i've did it for a twice now .. and it didn't make any sense like it doesn't change anything in settings or in touch pad or in sounds
or anything ... and when it was rebooting i've never heard sound of the fan ?? so what i have to do ?
and p.s : i've pressed Shift+ctrl+alt with the power button for a 5 seconds .. and i've released the shift+ctrl+alt buttons and i turn on the lap again ...
so what i have to do to reset it correctly ?
Model Name: MacBook Pro
Model Identifier: MacBookPro8,1
Processor Name: Intel Core i5
Processor Speed: 2.3 GHz
Number of Processors: 1
Total Number of Cores: 2
L2 Cache (per Core): 256 KB
L3 Cache: 3 MB
Memory: 4 GB
Boot ROM Version: MBP81.0047.B27
SMC Version (system): 1.68f99
Serial Number (system): C17FFQEKDH2G
Hardware UUID: FF9040EB-AAF5-5D01-BC5E-006BFC34890F
Sudden Motion Sensor:
State: Enabled
and it still like i don't made any reset !!
If I deciphered the tortured sentence, I suggest you read what I posted instead of deciding that there was no reset. THERE IS NO VISUAL CONFIRMATION OF A SMC RESET!
Barry
P.S. I am definitely not your "bro."
Similar Messages
-
with ctrl alt shift to reset, i noticed this created problem with normal setup.
things i noticed are that you can't open new file, it returns error message and you have to go to prefence and off open gl drawing to fix them.
and other thing if the mask black/white erasing doesn't work so well.
seems the hardness for brushes whether its 100 or 25, looks the same, i don't remember seeing this before in cs5, should reflect strenght between stronger /weaker erasing.things i noticed are that you can't open new file, it returns error message and you have to go to prefence and off open gl drawing to fix them.
That just means that your video card driver has some bugs, and needs to be updated.
The error messages tell you that there is a problem with your video card driver. -
Problems with resetting ipod touch
I wanted to reset my ipod touch to factory settings and I followed the instructions to do so; however, it's been approximately 5 hours since I've tried to reset it. All I see is the black screen with the apple sign in the middle. It turns off completely then goes back to the black screen with the apple sign about every 10-15 minutes. What should I do?
I've got that problem too. I did it earlier today, and its been about 5 hours, and its saying its trying to verify the ipod restore.
-
Hi all, I wanna ask support for my other account Skype where I can't reset my password. I try to reset it with my email and when I inserit new password the system give me problem and I can't log in to my account. Why? Why I can't use it anymore? Pls help me! It's a week that I can't use it! I can't remember all of my data to ask support for email... How I can do? I'm really desperate!
The passcode you need is the four digit number that you enter after an Autolock on your device or when you first turn it on. If you can't remember that code you'll have to restore your iPad before you can do the update.
http://support.apple.com/kb/HT1212 -
Hello All,
I have a form which has several fields. There is a reset button at the top of the Page -1 of the form which should clear/rest the form. But I have several checkboxes, out of which if some clicked few text fields / drop downs associated with it becomes mandatory. Suppose one clicks Checkbox -1 and the field TextField -1 associated with becomes mandatory.If the user clicks the reset button after clicking the checkbox (which makes the field mandatory) then though the checkbox is unchecked the field remains as mandatory. How to get over it with ? I have placed the script in the change event as well as in the click event of the text box as there are conditions to met (Suppose there are 3 check boxes associated with a text field and the field becomes mandatory if one of them is clicked) Any help would be greatly appreciated.
Thanks.
Bibhu.Hi Bibhu,
It is difficult to say without seeing the form, but a couple of things:
Try testing against null as well.
Check the binding on the checkbox on page1 that it has binding of '1' and '0'.
Double check the object reference for the checkbox on page1, eg is it in another subform.
Use the JavaScript Console (Control+J when previewing) to see are there any errors when exiting the textfield.
I would agree with the script being in the exit event.
I have an aversion to naming design pages with a capital 'P', as this is used for Master Pages, so I would generally use page1, ... page5. This isn't the problem here, just a comment.
Good luck,
Niall -
Problem with reset to factory settings.
I have a go notebook with the product number D1E89UA#ABA. I am wanting to reset this computer to factory settings but it won't let me. It has windows 8 on the computer so I click change pc settings and go down to general. Then I scroll down to where it says remove everything and reinstall windows. Then I click get started the I click next, then it says preparing. Then I click on fully clean the drive because I want it to be 100% factory settings. Then I have it plugged into the charger and click reset to reset the computer. Then every single time it says there's a problem no changes are made. Then I click check solutions to this problem and it never pops up any solutions. Please help!!
Hello @Rkaeden,
I understand that you are trying to recover your computer back to factory settings. I am providing you with an HP Support document: Performing an HP System Recovery (Windows 8), which will walk you through the process of doing a Factory Recovery on your computer.
I hope this helps. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
Problem with reset sync history
I am trying to troubleshoot a problem syncing with MobileMe on my MacPro workstation with Mac OS X 10.6.3 and everything current. When I go into iSync preferences and press the "reset sync history" button, it never seems to finish. Even if I reboot and then try to repeat it, the "reset sync history" button is grayed out, which suggests to me that it is still running. How can I fix this?
This just started working on its own.
-
Problem with resetting admin password
I lost my admin password so i booted from the install dvd to reset the password,
the problem is that the Macitosh HD doesn't appear on the list, the only thing on the list is the install dvd.
So I can't reset the admin account on the HDD, can anyone help me with this problem?
ArnootjeWelcome to the Apple Discussions:
In the Utility Menu on the DVD, can you run disk utility and repair HD and permissions? -
Sun 7120 - problems with resetting root password?
We have just taken delivery of a Sun 7120 system, did the initial config today no problems, then came to log in to tweak it and it refused my root password. Logged on the serial console with the same password fine, logged out and now it won't let me back in, just says "login incorrect". Have reset the CLR PW jumper on the mainboard, and rebooted and it then comes up in the preboot system, but reports errors about the ILOM. After powering down and removing the jumper, the root password is still there!
Output on bootup attached below, can anyone help?
Cheers
Primary Bootstrap.
U-Boot 1.1.4
Custom AST2100 U-Boot 3.0 (Aug 17 2010 - 01:30:05) r58107
DRAM: 119 MB
Flash bank 0 at 10000000 has 32MB in 256 sectors (chipSize 1<<25, ratio 1, bufSz
1024).
Flash: 32 MB
VUART1 at port 0x03f8, SerIRQ[4] disabled
VUART2 at port 0x02f8, SerIRQ[3] disabled
Protecting U-Boot flash sectors; monitor_base=10040000.
board_findGpioNum(): ERROR, 'BIOS_TOP_BLOCK_LOCK' does not match any pin.
board_findGpioNum(): ERROR, 'SP_PECI_ENABLE' does not match any pin.
H/W: Lynxplus Service Processor; SOC: AST2100 Rev. 02 ('A3')
PWC_SP_Broken_OD = 0; ARM restart caused by: power-on
The host is OFF(S5) (hostWantsPwr=0, powerGood=0,
allowPwrOn=0|0, outOfReset=0, fatalError=0).
Reset straps=0x8c819180, def. H-PLL=264 MHz, CPU/AHB=2:1, boot CS0# normal spe
ed
PCI w/VGA noVBIOS; NOR 38ns/byte; DRAM clock is M-PLL: 264 MHz (DDR2-528)
DRAM: 128MB data - 8MB VGA, 32-bit noECC, 2 BA 10 CA, CL=4 BL=4 ap=1, 61440 us
refr
Board Revision - 8d
Date: 2011-01-19 (Wednesday) Time: 7:04:21
Reading FRUID...Valid CRC.
ethaddr=00:21:28:3D:BD:9A
eth1addr=00:21:28:3D:BD:9B
Net: MAC1 PHY not ready faradaynic#0, faradaynic#1
Enter Diagnostics Mode ['q'uick/'n'ormal(default)/e'x'tended(manufacturing mode)
] ..... 0
Diagnostics Mode - NORMAL
<DIAGS> Memory Data Bus Test ... PASSED
<DIAGS> Memory Address Bus Test ... PASSED
I2C Probe Test - Motherboard
Bus Device Address Result
=== ============================ ======= ======
2 Sys FRUID (U3003) 0xA0 PASSED
2 Power CPLD (U3301) 0x4E PASSED
2 CPU0 Fault LED's (U3001) 0x40 PASSED
2 CPU1 Fault LED's (U3002) 0x42 PASSED
2 PCA9555 (Misc) (U3005) 0x44 PASSED
2 DIMM IMAX (U3102) 0x12 PASSED
6 Bank Panel Led's (U2701) 0xC6 PASSED
6 DS1338(RTC) ( U803) 0xD0 PASSED
6 Temp Sensor1(LM75) (U3011) 0x90 PASSED
6 Temp Sensor2(LM75) (U3012) 0x92 PASSED
6 Temp Sensor3(LM75) (U3010) 0x94 PASSED
I2C Probe Test - Chassis(2U HYDE24)
PDB Board
Bus Device Address Result
=== ============================ ======= ======
1 PCA9548 Mux (U0202) 0xE0 PASSED
1 PDB FRUID (U0203) 0xAA PASSED
1 MAX7313 (U0201) 0x40 PASSED
1 MAX7315 (U1001) 0x46 PASSED
Power Supply 0
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 0 PS 0 FRUID ( - ) 0xAC PASSED
1 0 PS 0 CTRL ( - ) 0x7C PASSED
Power Supply 1
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 1 PS 1 FRUID ( - ) 0xAC PASSED
1 1 PS 1 CTRL ( - ) 0x7C PASSED
Unified Fan Module
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 2 FT 0 FRUID (U0203) 0xAC PASSED
1 2 FT 0 MAX7313 (U0201) 0x42 PASSED
1 2 FT 0 ADT7462 (U0202) 0xB8 PASSED
1 3 FT 1 MAX7313 (U0501) 0x42 PASSED
1 3 FT 1 ADT7462 (U0502) 0xB8 PASSED
24 Disk Backplane
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 4 BP MAX7313 ( U8) 0x44 PASSED
1 4 BP FRUID ( U6) 0xAC PASSED
LSI Daughter Card
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 4 EXP FRUID ( U07) 0xA0 PASSED
1 4 EXP Tmp Sens ( U04) 0x98 PASSED
1 4 EXP PCA9538 ( U10) 0xE6 PASSED
1 4 EXP EMP570 ( U05) 0x50 PASSED
Connector Board
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 4 CONN FRUID ( U05) 0xA2 PASSED
<DIAGS> PHY #0 R/W Test ... PASSED
<DIAGS> PHY #0 Link Status ... FAILED
MAC1 PHY not ready <DIAGS> ETHERNET PHY #0, Internal Loopback Test ... RX error
status = 0xB00905C0
FAILED
No data received
<DIAGS> USB 1.1 Test ... PASSED
<DIAGS>Access to BIOS Flash ... PASSED
<DIAGS> Testing PowerCPLD version ... PASSED
checking for abnormal reboots: 0:0.
abnormal reboot found -- too long, ignore
Booting linux in 3 seconds...
Un-Protect Flash Bank # 1
flctrl: Recovery U-Boot (r58107) at 0x10040000 is valid (min. r51654).
flctrl: Current U-Boot is not the main one.
bootpkg: Not safe to boot ILOM (stat=1). Check Preboot "vers" command,
then reload ILOM ("net flash") as needed.
ILOM Pre-boot Menu
Type "h" and [Enter] for a list of commands, or "?" [Enter] for
command-line key bindings. Type "h cmd" for summary of 'cmd' command.
Idle time-out is disabled. Set 'bootretry' to enable it.
This is Recovery U-Boot. Use "vers all" to check flash images.
Preboot> vers all
Main ILOM image at 0x100a0000:
Service Processor Firmware
Version = 3.0.9.27, for SP type 52
Date ='Tue Aug 17 01:54:07 EDT 2010', Build ='r58107'
Name ='sysbios'
uboot @0a0000 OK, kernel @102000 OK, root @20d684 OK,
sysbios @c9b6c4 OK, pwrseq @d51aa2 OK, pbsw @d6096c OK
coredump @1500000 8192 KiB, persist @1d00000 2048 KiB, params @1f00000 1024
KiB
Recovery firmware and data:
Normal U-Boot at 0x100a0000:
Date ='Aug 17 2010', Build ='r58107'
uboot @0a0000 OK
Recovery U-Boot at 0x10040000:
Date ='Aug 17 2010', Build ='r58107'
uboot @040000 OK
Primary Bootstrap build: r52205
Permanent environment: not foundI don't think it is. The jumper you saw is likely the ILOM jumper. The ILOM is different than the BUI(OS) password so they can be reset/changed independently.
-
Problem with Reset/Refresh after Windows 8.1 upgrade
When I try to do a Refresh or Reset on my Helix after it has been upgraded to 8.1, I receive a message to "Insert Media. Some of the files are missing." Does anyone know how to fix this?
I have same problem, there are some solutions on my thread you can check them out if you like.
http://forums.lenovo.com/t5/ThinkPad-Edge-S-series/Unable-to-Reset-Refresh/td-p/1533410 -
Problem with reseting my security question
Hi,
Recently i want purchase cash from racing rivals, the saddest thing i forrgot my security answer,and i went to reset my security question but i was unable to reset..so please help me out,the info from customer care doesnt help me.Thank youWell, if you already tried resetting through iforgot.apple.com and you could not, you need to get in touch with AppleID account security to see if they can help you with this.
Go here:
http://support.apple.com/kb/HT5699?viewlocale=en_US -
Ise patch 1 and 2 for 1.1.4 problem with resetting-application
Hi guys,
For your info. ISE patch 1 and 2 got the same problem on 1.1.4. If you got patches installed and tries to reset the application of ISE the monitoring applets are all gone. It's loading an empty page. Solution: rollback any installed patches. Monitoring is back up again. Install the patches again and erverything is fine. Took me one afternoon to figure this out.Hi Ravi,
Do you know, what is going wrong? I'm wondering if everything is working correctly and if patches are applied correctly. -
Problems with resetting my iPhone 5 (iOS 7.1.2)
Good afternoon,
I just updated my account regarding a new e-mail address, a new password, new security questions etc.
After that, I wanted to reset my iPhone 5. I tried resetting it directly on my phone which did not work out because in the end, you need to type your passwort but unfortunately, it still showed my old e-mail address and it would not accept neither my old nor my new password.
So I connected my iPhone to iTunes and tried resetting it on my computer. This was not possible as I connected my iPhone to "FindMyiPhone" (Or whatever it is called in English ;-)). So I logged in on www.icloud.com and tried to delete my iPhone. I think, this is where I messed up badly.
Right now, my iPhone shows the "I have lost this iPhone, please call me xxx" and it seems impossible to set it up.
iTunes says it is not possible to connect to my iPhone as the SIM card is locked.
I have absolutely no idea what to do anymore.
It would be very nice if someone could help me here.....
Thanks in advance!I had the exact same problem for the last two days. I deleted my account on my iPhone, but it would still say the user/password were incorrect and the server connection failed when trying to add it back. I tried to log on through the browser but I would get the same error message. I clicked on "I forgot my password" and reset it to the exact same password I already had. This allowed me into my email. I was then able to successfully add the email account back to my phone.
-
Hi friends...
I got one view iny application where i have few drop down list and input fields...
i hve two buttons submuit and reset...
when i submit i will get the table based on the i/ps from dropdownlist.....
my requirement is
I have Reset button...When i press Reset button the the data should be refreshed and it shopuld appear just as it appeared before at first...
All the dropdown Index the lead selection should be to the first and the table should be empty........Hi
I have written ur code but the table is not refrreshed and dropdown list by index are not reset....
I have added dropdownlist BY index and added with with Select- at the top of the drop down list
when i press reset button the pointer should go to the ---Select -- just as it came when i loaded the view for the first time.....
and the table should also be refreshed.....
i should get table with no values........... -
Problem with reseting Meta Data
hi everyone heres my problem...
i keep all of my music on my external hard drive and i frequently clear my Itunes and reload all my music. When i do this i notice the my HOURS that ive spent formating the meta data for my music the way i like it has been reset to the way it was before...is there any way to permanatly change the info for a song without manually finding it in the folder and editing its properties there track by track?I just realized...is the meta date info you are loosing the individual Artist, Album Title, Year, Track Number, Genre, Song Title info?
If yes, then you can hard code that into the song files by locating the individual songs in My Computer and navigating to your external hard drive and finding the song and then highlight the song file and right click your mouse and choose Properties. There will be a Summary tab - click that. Then click Advanced. There is where you can hard code the meta data for the song file.
I hope that is what you are looking for and that I helped you once again.
Maybe you are looking for
-
Trying to change broadband package
I've been trying to change my broadband package for over a month now. I'm still on the old Option 3 unlimited broadband, I want to be on the current Unlimited broadband package which is half the price for the same service (£16 versus £30.50). I sen
-
How to embed more than 393 chars in form fields
how to embed more than 1000 character in the field. I have written a xsl template which is about 2 pages in length. How do I embed it in the word template fields.
-
Using front row, in reality
I have finally got front row to appear on my TV screen in the sitting room, this has involved quite a bit of faffing around having to mirror the display etc etc. It is primarily to play music from the iMac to my hifi which is also connected into the
-
Looking for photoshop camera raw plug in version 8.3
looking for photoshop camera raw plug in version 8.3 In Lightroom 5.3 I am trying to edit an (OLYMPUS) ORF file in PHOTOSHOP when I get the message I need the above plug in Help in trying to install
-
I never use it to dictate my text messages or any other thing I need typed so it just gets in the way please help.