Problem with SNR on CME
Dear Experts,
I have problem with SNR on CME.
When I make call from internal, SNR is working, but when calling from outside to one of my SNR extension, its not
working - not ringing on mobile device.
but from extension 43 I am allowed to call xxxxxxxxx -so when making callforward to xxxxxxxxx its working.
ephone-dn 43 dual-line
number 43 no-reg primary
pickup-group 4
label xxx
description xxx
name xxx
mobility
snr xxxxxxxx delay 1 timeout 18 cfwd-noan 90
snr ring-stop
snr answer-too-soon 4
allow watch
call-forward busy 90
call-forward noan 90 timeout 18
need help
There is a well know issue with SNR and Call forward all when the calling number is not a DID assigned by the Telco.
Post here your debug isdn q931 to confirm if it is the case. Most likely you will have to convince your Telco to let you do this or implement translation rules on the voice gateway to override the calling number.
Olease rate helpful answers!
Similar Messages
-
1751-V with 12.4(9)T CME 4.0 Problems with 7920
Hi. I had a 1751-V running without problems with 7940,7960 and 7912 phones.. I configured a new 7920 in the system and when the 7920 register with the CME all the 7940 and 7960 IP Phones unregister from the router and they only came back if I turn off the 7920.The 7912 IP Phone is working fine. I don't know if it is something related to CME or to DHCP. THe router is also the DHCP server..
Attach debugs from the router and relevant configuration..
Any ideas?
Thanks in advanced,
-JoseUpgrade phone firmware CMtern _7920.4.0-03-00
-
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
2 Problems with the Ipad Air...midi keyboard and usb microphone
IN SHORT:
2 Problems with the Ipad Air...what midi keyboard will connect to the lightning camera connector and what microphone as well? There seems to be issues with the ipad air not being able to power them. Has anyone got any devices to work yet?
IN DEPTH:
I have a yeti microphone that when I plug in it says its using too much power. A little samsung go mic I have plugs in find and works but isnt quite what im looking for. My midi keyboard is not reading...its probably 15yrs old (didnt expect it to work). I have ordered a usb powered keyboard but im now nervous it may not work if it requires too much power. Has anyone had any success with a particular model of keybaord? I saw a youtube video of the CME Xkey in which it was plugged into an ipad that uses the lightning jack, but was unsure if it was the air or a different model.
Any help is appreciated on this...I love my ipad air and hoping to make it my fully functional music recording device.
By the way I mostly use garagebandhey mate
Yes what I ended up doing is buying a powered usb hub. They are about 10 dollars or so on amazon.com. There are tons to choose from. I use a yeti micrphone now with no issues and a midi keyboard. You will need the lightning usb adapter too. You plug the lightning adapter into the ipad and the hub into the adapter then plug all your accessories into the powered hub. So it works well you just gotta buy an extra piece of equipment. -
I am trying to implement some kind of a server listening for requests. The listener part of the app, is a daemon thread that listens for connections and instantiates a handling daemon thread once it gets some. However, my problem is that i must be able to kill the listening thread at the user's will (say via a sto button). I have done this via the Sun's proposed way, by testing a boolean flag in the loop, which is set to false when i wish to kill the thread. The problem with this thing is the following...
Once the thread starts excecuting, it will test the flag, find it true and enter the loop. At some point it will LOCK on the server socket waiting for connection. Unless some client actually connects, it will keep on listening indefinatelly whithought ever bothering to check for the flag again (no matter how many times you set the damn thing to false).
My question is this: Is there any real, non-theoretical, applied way to stop thread in java safely?
Thank you in advance,
LeftyThis was one solution from the socket programming forum, have you tried this??
public Thread MyThread extends Thread{
boolean active = true;
public void run(){
ss.setSoTimeout(90);
while (active){
try{
serverSocket = ss.accept();
catch (SocketTimeoutException ste){
// do nothing
// interrupt thread
public void deactivate(){
active = false;
// you gotta sleep for a time longer than the
// accept() timeout to make sure that timeout is finished.
try{
sleep(91);
}catch (InterruptedException ie){
interrupt();
} -
Problem with Threads and a static variable
I have a problem with the code below. I am yet to make sure that I understand the problem. Correct me if I am wrong please.
Code functionality:
A timer calls SetState every second. It sets the state and sets boolean variable "changed" to true. Then notifies a main process thread to check if the state changed to send a message.
The problem as far I understand is:
Assume the timer Thread calls SetState twice before the main process Thread runs. As a result, "changed" is set to true twice. However, since the main process is blocked twice during the two calls to SetState, when it runs it would have the two SetState timer threads blocked on its synchronized body. It will pass the first one, send the message and set "changed" to false since it was true. Now, it will pass the second thread, but here is the problem, "changed" is already set to false. As a result, it won't send the message even though it is supposed to.
Would you please let me know if my understanding is correct? If so, what would you propose to resolve the problem? Should I call wait some other or should I notify in a different way?
Thanks,
B.D.
Code:
private static volatile boolean bChanged = false;
private static Thread objMainProcess;
protected static void Init(){
objMainProcess = new Thread() {
public void run() {
while( objMainProcess == Thread.currentThread() ) {
GetState();
objMainProcess.setDaemon( true );
objMainProcess.start();
public static void initStatusTimer(){
if(objTimer == null)
objTimer = new javax.swing.Timer( 1000, new java.awt.event.ActionListener(){
public void actionPerformed( java.awt.event.ActionEvent evt){
SetState();
private static void SetState(){
if( objMainProcess == null ) return;
synchronized( objMainProcess ) {
bChanged = true;
try{
objMainProcess.notify();
}catch( IllegalMonitorStateException e ) {}
private static boolean GetState() {
if( objMainProcess == null ) return false;
synchronized( objMainProcess ) {
if( bChanged) {
SendMessage();
bChanged = false;
return true;
try {
objMainProcess.wait();
}catch( InterruptedException e ) {}
return false;
}Thanks DrClap for your reply. Everything you said is right. It is not easy to make them alternate since SetState() could be called from different places where the state could be anything else but a status message. Like a GREETING message for example. It is a handshaking message but not a status message.
Again as you said, There is a reason I can't call sendMessage() inside setState().
The only way I was able to do it is by having a counter of the number of notifies that have been called. Every time notify() is called a counter is incremented. Now instead of just checking if "changed" flag is true, I also check if notify counter is greater than zero. If both true, I send the message. If "changed" flag is false, I check again if the notify counter is greater than zero, I send the message. This way it works, but it is kind of a patch than a good design fix. I am yet to find a good solution.
Thanks,
B.D. -
Problem with threads running javaw
Hi,
Having a problem with multi thread programming using client server sockets. The program works find when starting the the application in a console using java muti.java , but when using javaw multi.java the program doesnt die and have to kill it in the task manager. The program doesnt display any of my gui error messages either when the server disconnect the client. all works find in a console. any advice on this as I havent been able to understand why this is happening? any comment would be appreciated.
troy.troy,
Try and post a minimum code sample of your app which
does not work.
When using javaw, make sure you redirect the standard
error and standard output streams to file.
Graeme.Hi Graeme,
I dont understand what you mean by redirection to file? some of my code below.
The code works fine under a console, code is supposed to exit when the client (the other server )disconnects. the problem is that but the clientworker side of the code still works. which under console it doesnt.
public class Server{
ServerSocket aServerSocket;
Socket dianosticsSocket;
Socket nPortExpress;
ClientListener aClientListener;
LinkedList queue = new LinkedList();
int port = 0;
int clientPort = 0;
String clientName = null;
boolean serverAlive = true;
* Server constructor generates a server
* Socket and then starts a client threads.
* @param aPort socket port of local machine.
public Server(int aPort, String aClientName, int aClientPort){
port = aPort;
clientName = aClientName;
clientPort = aClientPort;
try{
// create a new thread
aServerSocket = new ServerSocket(port) ;
// connect to the nPortExpress
aClientListener = new ClientListener(InetAddress.getByName(clientName), clientPort, queue,this);
// aClientListener.setDaemon(true);
aClientListener.start();
// start a dianostic port
DiagnosticsServer aDiagnosticsServer = new DiagnosticsServer(port,queue,aClientListener);
// System.out.println("Server is running on port " + port + "...");
// System.out.println("Connect to nPort");
catch(Exception e)
// System.out.println("ERROR: Server port " + port + " not available");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Server port " + port + " not available", JOptionPane.ERROR_MESSAGE);
serverAlive = false;
System.exit(1);
while(serverAlive&&aClientListener.hostSocket.isConnected()){
try{
// connect the client
Socket aClient = aServerSocket.accept();
//System.out.println("open client connection");
//System.out.println("client local: "+ aClient.getLocalAddress().toString());
// System.out.println("client localport: "+ aClient.getLocalPort());
// System.out.println("client : "+ aClient.getInetAddress().toString());
// System.out.println("client port: "+ aClient.getLocalPort());
// make a new client thread
ClientWorker clientThread = new ClientWorker(aClient, queue, aClientListener, false);
// start thread
clientThread.start();
catch(Exception e)
//System.out.println("ERROR: Client connection failure");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Client connection failure", JOptionPane.ERROR_MESSAGE);
}// end while
} // end constructor Server
void serverExit(){
JOptionPane.showMessageDialog(null, "Server ","ERROR: nPort Failure", JOptionPane.ERROR_MESSAGE);
System.exit(1);
}// end class Server
*** connect to another server
public class ClientListener extends Thread{
InetAddress hostName;
int hostPort;
Socket hostSocket;
BufferedReader in;
PrintWriter out;
boolean loggedIn;
LinkedList queue; // reference to Server queue
Server serverRef; // reference to main server
* ClientListener connects to the host server.
* @param aHostName is the name of the host eg server name or IP address.
* @param aHostPort is a port number of the host.
* @param aLoginName is the users login name.
public ClientListener(InetAddress aHostName, int aHostPort,LinkedList aQueue,Server aServer) // reference to Server queue)
hostName = aHostName;
hostPort = aHostPort;
queue = aQueue;
serverRef = aServer;
// connect to the server
try{
hostSocket = new Socket(hostName, hostPort);
catch(IOException e){
//System.out.println("ERROR: Connection Host Failed");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Connection to nPort Failed", JOptionPane.ERROR_MESSAGE);
System.exit(0);
} // end constructor ClientListener
** multi client connection server
ClientWorker(Socket aSocket,LinkedList aQueue, ClientListener aClientListener, boolean diagnostics){
queue = aQueue;
addToQueue(this);
client = aSocket;
clientRef = aClientListener;
aDiagnostic = diagnostics;
} // end constructor ClientWorker
* run method is the main loop of the server program
* in change of handle new client connection as well
* as handle all messages and errors.
public void run(){
boolean alive = true;
String aSubString = "";
in = null;
out = null;
loginName = "";
loggedIn = false;
while (alive && client.isConnected()&& clientRef.hostSocket.isConnected()){
try{
in = new BufferedReader(new InputStreamReader(client.getInputStream()));
out = new PrintWriter(new OutputStreamWriter(client.getOutputStream()));
if(aDiagnostic){
out.println("WELCOME to diagnostics");
broadCastDia("Connect : diagnostics "+client.getInetAddress().toString());
out.flush();
else {
out.println("WELCOME to Troy's Server");
broadCastDia("Connect : client "+client.getInetAddress().toString());
out.flush();
String line;
while(((line = in.readLine())!= null)){
StringTokenizer aStringToken = new StringTokenizer(line, " ");
if(!aDiagnostic){
broadCastDia(line);
clientRef.sendMessage(line); // send mesage out to netExpress
out.println(line);
out.flush();
else{
if(line.equals("GETIPS"))
getIPs();
else{
clientRef.sendMessage(line); // send mesage out to netExpress
out.println(line);
out.flush();
} // end while
catch(Exception e){
// System.out.println("ERROR:Client Connection reset");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR:Client Connection reset", JOptionPane.ERROR_MESSAGE);
try{
if(aDiagnostic){
broadCastDia("Disconnect : diagnostics "+client.getInetAddress().toString());
out.flush();
else {
broadCastDia("Disconnect : client "+client.getInetAddress().toString());
out.flush();
// close the buffers and connection;
in.close();
out.close();
client.close();
// System.out.println("out");
// remove from list
removeThreadQueue(this);
alive = false;
catch(Exception e){
// System.out.println("ERROR: Client Connection reset failure");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Client Connection reset failure", JOptionPane.ERROR_MESSAGE);
}// end while
} // end method run
* method run - Generates io stream for communicating with the server and
* starts the client gui. Run also parses the input commands from the server.
public void run(){
boolean alive = true;
try{
// begin to life the gui
// aGuiClient = new ClientGui(hostName.getHostName(), hostPort, loginName, this);
// aGuiClient.show();
in = new BufferedReader(new InputStreamReader(hostSocket.getInputStream()));
out = new PrintWriter(new OutputStreamWriter(hostSocket.getOutputStream()));
while (alive && hostSocket.isConnected()){
String line;
while(((line = in.readLine())!= null)){
System.out.println(line);
broadCast(line);
} // end while
} // end while
catch(Exception e){
// System.out.println("ERRORa Connection to host reset");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Connection to nPort reset", JOptionPane.ERROR_MESSAGE);
try{
hostSocket.close();
}catch(Exception a){
JOptionPane.showMessageDialog(null, (a.toString()),"ERROR: Exception", JOptionPane.ERROR_MESSAGE);
alive = false;
System.exit(1);
} // end method run -
Problem with threads and camera.
Hi everybody!
I've a problem with taking snapshot.
I would like to display a loading screen after it take snapshot ( sometimes i
have to wait few seconds after i took snapshot. Propably photo is being taken in time where i have to wait).
I was trying to use threads but i didn't succeed.
I made this code:
display.setCurrent(perform);
new Thread(new Runnable(){
public void run() {
while((!performing.isShown()) && (backgroundCamera.isShown())){
Thread.yield();
notifyAll();
}).start();
new Thread(new Runnable(){
public void run() {
try {
this.wait();
} catch(Exception e) {
exceptionHandler(e);
photo = camera.snapshot();
display.setCurrent(displayPhoto);
}).start();This code is sometimes showing performing screen but sometimes no.
I don't know why. In my opinion performing.isShown() method isn't working correctly.
Does anyone have some idea how to use threads here?Hi,
I've finally managed to work this fine.
The code:
Object o = new Object();
display.setCurrent(perform);
new Thread(new Runnable(){
public void run() {
while(!performing.isShown()){
Thread.yield();
synchronized(o) {
o.notify();
}).start();
new Thread(new Runnable(){
public void run() {
try {
synchronized(o) {
o.wait(1);
} catch(Exception e) {
exceptionHandler(e);
photo = camera.snapshot();
display.setCurrent(displayPhoto);
}).start(); -
We have a problem where our application stops responding after a few days of usage. Things will for fine for a day or two, and then pretty quickly threads will start getting hung up, usually in places where they are allocating memory
We are running WebLogic 8.1 SP2 on Sun JDK 1.4.2_04 on Solaris 8 using the alternate threading model and the -server hotspot vm. We are running pretty much the same code that we had no problems with under WebLogic 6.1 SP4 and Sun JDK 1.3.1.
A thread dump usually shows that some or all of our execute threads are in the state "waiting for monitor entry" even though they are not currently waiting on any java locks. Here is a sample thread from the thread dump (we have ~120 threads so I don't want to post the full dump).
=============================================================================================
"ExecuteThread: '8' for queue: 'itgCrmWarExecutionQueue'" daemon prio=5 tid=0x005941d0 nid=0x2c waiting for monitor entry [c807f000..c807fc28]
at java.lang.String.substring(String.java:1446)
at java.lang.String.substring(String.java:1411)
at weblogic.servlet.internal.ServletRequestImpl.getRelativeUri(ServletRequestImpl.java:1872)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3492)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
=============================================================================================
String.java line 1446 for this jdk allocates a new String object, and all the other threads in this state also are creating new objects or arrays, etc.
We've done a pstack on this process when it's in this state, and the threads that are in the "waiting for monitor entry" that look like they're allocating memory are all waiting on the same lwp_mutex_lock with some allocation method that's calling into the native TwoGenerationCollectorPolicy.mem_allocate_work (see pstack output below for the same thread as in the thread dump above)
=============================================================================================
----------------- lwp# 44 / thread# 44 --------------------
ff31f364 lwp_mutex_lock (e3d70)
fee92384 __1cNObjectMonitorGenter26MpnGThread__v_ (5000, 525c, 5000, 50dc, 4800, 4af0) + 2d8
fee324d4 __1cSObjectSynchronizerKfast_enter6FnGHandle_pnJBasicLock_pnGThread__v_ (c807f65c, c807f7d4, 5941d0, 0, 35d654, fee328ec) + 68
fee32954 __1cQinstanceRefKlassZacquire_pending_list_lock6FpnJBasicLock__v_ (c807f7d4, ff170000, d4680000, 4491d4, fee1bc2c,
0) + 78
fee3167c __1cPVM_GC_OperationNdoit_prologue6M_i_ (c807f7bc, 4400, ff170000, 2d2b8, 4a6268, c807fa18) + 38
fee2e0b0 __1cIVMThreadHexecute6FpnMVM_Operation__v_ (c807f7bc, 963a8, 0, 0, 1, 0) + 90
fed2c2a4 __1cbCTwoGenerationCollectorPolicyRmem_allocate_work6MIii_pnIHeapWord__ (962c0, ff1c29ec, ff1c297c, ff131a26, 4800, 4998) + 160
fed22940 __1cNinstanceKlassRallocate_instance6MpnGThread__pnPinstanceOopDesc__ (ee009020, 5941d0, 15ca581, 3647f0, 4a6268, c807f8c8) + 180
fed34928 __1cLOptoRuntimeFnew_C6FpnMklassOopDesc_pnKJavaThread__v_ (ee009018, 5941d0, 0, 0, 0, 0) + 28
fa435a58 ???????? (ee009018, e86de, 15ca4de, 50dc, 5941d0, c807f9c8)
fb36f9a4 ???????? (0, d412ccd8, ee046c28, ff170000, 0, 0)
fad8b278 ???????? (ee046c28, d6000c90, ee046530, 8, db8e8450, c807f9e8)
fad62abc ???????? (d412ccd8, ee046530, d6000c90, ee3bfa38, 8, c807fa18)
fa4b3c38 ???????? (c807fb9c, 0, f2134700, fa415e50, 8, c807faa8)
fa40010c ???????? (c807fc28, c807fe90, a, ee9e1e20, 4, c807fb40)
fed5d48c __1cJJavaCallsLcall_helper6FpnJJavaValue_pnMmethodHandle_pnRJavaCallArguments_pnGThread__v_ (c807fe88, c807fcf0, c807fda8, 5941d0, 5941d0, c807fd00) + 27c
fee4b784 __1cJJavaCallsMcall_virtual6FpnJJavaValue_nLKlassHandle_nMsymbolHandle_4pnRJavaCallArguments_pnGThread__v_ (ff170000, 594778, c807fd9c, c807fd98, c807fda8, 5941d0) + 164
fee5e8dc __1cJJavaCallsMcall_virtual6FpnJJavaValue_nGHandle_nLKlassHandle_nMsymbolHandle_5pnGThread__v_ (c807fe88, c807fe84, c807fe7c, c807fe74, c807fe6c, 5941d0) + 6c
fee6fc74 __1cMthread_entry6FpnKJavaThread_pnGThread__v_ (5941d0, 5941d0, 838588, 594778, 306d10, fee69254) + 128
fee6927c __1cKJavaThreadDrun6M_v_ (5941d0, 2c, 40, 0, 40, 0) + 284
fee6575c _start (5941d0, fa1a1600, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Also when it's having this problem, the "VM Thread" is always using a lot of processor time. We did a couple of pstacks today while it was having this problem, and this thread was stuck in the ONMethodSweeper.sweep for over 15 minutes when we finally killed the server.
From the thread dump:
"VM Thread" prio=5 tid=0x000e2d20 nid=0x2 runnable
From the first pstack:
=============================================================================================
----------------- lwp# 2 / thread# 2 --------------------
fed40c04 __1cXvirtual_call_RelocationIparse_ic6FrpnICodeBlob_rpC5rppnHoopDesc_pi_nNRelocIterator__ (42a2f4, fa5fa46d, ffffffff, fc4ffcb8, 42a2f4, 42a324) + 124
fed46318 __1cKCompiledIC2t5B6MpnKRelocation__v_ (42a2f0, fc4ffd24, fc4ffd4c, e802, 0, 6) + 38
fed90c38 __1cHnmethodVcleanup_inline_caches6M_v_ (fa5f7f88, fa608940, 1, 0, fa400000, 6) + 1ac
fede18b4 __1cONMethodSweeperFsweep6F_v_ (2cf38, 0, ffffffff, ff1cf1fc, ff1c66e8, fede1d44) + 1b0
fede1e6c __1cUSafepointSynchronizeFbegin6F_v_ (2cf38, ff1ba138, 5000, 50dc, 5000, 525c) + 248
feef1fd4 __1cIVMThreadEloop6M_v_ (4400, 4000, 4324, 4000, 42b0, 3800) + 3d4
feef1ae4 __1cIVMThreadDrun6M_v_ (e2d20, 2, 40, 0, 40, 0) + 8c
fee6575c _start (e2d20, ff270200, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Second pstack
=============================================================================================
----------------- lwp# 2 / thread# 2 --------------------
fed41180 __1cXvirtual_call_RelocationIparse_ic6FrpnICodeBlob_rpC5rppnHoopDesc_pi_nNRelocIterator__ (0, ff1b9664, ffffffff, fc4ffcb8, a6f2cc, fc4ffbd0) + 6a0
fed46318 __1cKCompiledIC2t5B6MpnKRelocation__v_ (a6f2c8, fc4ffd24, fc4ffd4c, e802, 0, 6) + 38
fed90c38 __1cHnmethodVcleanup_inline_caches6M_v_ (faded4c8, fadf2c80, 1, 0, fa400000, 6) + 1ac
fede18b4 __1cONMethodSweeperFsweep6F_v_ (2cf38, 0, ffffffff, ff1cf1fc, ff1c66e8, fede1d44) + 1b0
fede1e6c __1cUSafepointSynchronizeFbegin6F_v_ (2cf38, ff1ba138, 5000, 50dc, 5000, 525c) + 248
feef1fd4 __1cIVMThreadEloop6M_v_ (4400, 4000, 4324, 4000, 42b0, 3800) + 3d4
feef1ae4 __1cIVMThreadDrun6M_v_ (e2d20, 2, 40, 0, 40, 0) + 8c
fee6575c _start (e2d20, ff270200, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Has anyone ever seen anything like this? I'm trying to figure out if this is caused by something we're doing, or something relating to our environment and jvm options. Any ideas?Thanks for the reply - I'm testing our app with the +UseConcMarkSweepGC now in our test environment to make sure it doesn't cause any problems there. Unfortunately the only place we've had this problem is on the production server, so it's extra difficult debugging this.
We're using the following memory options:
-ms512m -mx512m -XX:NewSize=128m -XX:PermSize=192m -XX:MaxNewSize=128m -XX:MaxPermSize=192m -XX:SurvivorRatio=8and the following debugging options, as we've also been seeing OutOfMemoryErrors ( see http://forum.java.sun.com/thread.jsp?forum=37&thread=522354&tstart=45&trange=15 )
-verbosegc -XX:+PrintGCDetails -XX:+PrintGCTimeStamps -XX:+PrintHeapAtGCBTW, which c++filt version and options are you using? Our Solaris boxes only seem to have the GNU version installed. I was trying to run that on some of the other stack traces and wasn't getting anywhere, and didn't know if because it was GNU version wouldn't work on something compiled with the Sun compiler.
Thanks!
--Andy -
Problem with threads and ProgressMonitor
Dear Friends:
I have a little problem with a thread and a ProgressMonitor. I have a long time process that runs in a thread (the thread is in an separate class). The thread has a ProgressMonitor that works fine and shows the tasks progress.
But I need deactivate the main class(the main class is the user interface) until the thread ends.
I use something like this:
LongTask myTask=new LongTask();
myTask.start();
myTask.join();
Now, the main class waits for the task to end, but the progress monitor don`t works fine: it shows only the dialog but not the progress bar.
What's wrong?Is the dialog a modal dialog? This can block other UI updates.
In general, you should make sure that it isn't modal, and that your workThread has a fairly low priority so that the UI can do its updating -
Problem with threads and/or memory
I'm developing an application where there are 3 threads. One of them sends a request to the other, and if the 2nd can't answer it, it sends it to the 3rd (similar to CPU -> CACHE -> MEMORY). When i run the program with 1000-10.000 requests, no problem occurs. When i run it with 300.000-1.000.000 requests, it sometimes hangs. Is this a problem with the garbage collector, or should it be related to the threads mecanism.
(note: eache thread is in execution using a finite state machine)i had been running the program inside Netbeans.
Running the jar using the command line outside
Netbeans i have no more problems... Does Netbeans use
it's own JVM?Depends how you set it up, but look under the options. There are settings for the compiler and jvm that it uses. -
Installation problem with NW'04 SR1: database connection failed
Hi all,
while installing NW '04 SR1 on Windows Server 2003 SP1 and MS SQL Server 2000 SP4 I ran into an error related to the database connection. While performing the step "Load Java Database content" SAPinst crashes with the message
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
The connection to the SLQ Server with e.g. the Query Analyzer is OK. I had a problem with this installation setup before (have a look at the corresponding <a href="https://forums.sdn.sap.com/thread.jspa?threadID=338638&tstart=0">thread</a> ), the JDBC drivers where missing on the installation master but after copying them in the right direction the installation went on with no problem up to this point...
Has anybody an idea what could have happened here? Is this maybe a problem connected to the one I recently had
Below I attached the sapinst.log and jload.log with more detailed messages.
sapinst.log ###########
INFO 2007-03-12 22:06:24
Working directory changed to C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_~1\ONE_HOST.
INFO 2007-03-12 22:06:24
Output of D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log' is written to the logfile C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_~1\ONE_HOST/jload.java.log.
WARNING 2007-03-12 22:06:26
Execution of the command "D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log'" finished with return code 1. Output:
java version "1.4.2_13"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_13-b06)
Java HotSpot(TM) Client VM (build 1.4.2_13-b06, mixed mode)
12.03.2007 22:06:25 com.sap.inst.jload.Jload main
INFO: Jload -sec WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key -dataDir S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP -job C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML -log C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log
12.03.2007 22:06:26 com.sap.inst.jload.Jload main
SCHWERWIEGEND: couldn't connect to DB
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
ERROR 2007-03-12 22:06:26
CJS-20065 Execution of JLoad tool 'D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log'' aborts with returncode 1. Check 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log' and 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.java.log' for more information.
jload.log ###########
12.03.07 22:06 com.sap.inst.jload.Jload main
INFO: Jload -sec WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key -dataDir S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP -job C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML -log C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log
12.03.07 22:06 com.sap.inst.jload.Jload main
SEVERE: couldn't connect to DB
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
Best regards,
BerndHello Kairat,
Please follow the below mentioned guide to install it.
Check all the parameters to set and run pre requisite checker before starting installation.
Keep in mind that before starting any SAP installation you should always run prerequisite checker.
https://websmp205.sap-ag.de/instguides --> SAP Netweaver -->SAP Netweaver 7.0 -- > Installations --> EHP2
Regards,
Amit Barnawal -
My app store wont let me download apps, asks me to update my payment details then says theres a problem with previous purchase and card is expired which is untrue someone help me pls
This is a User to User Forum...
See Here for
Mac Apps Store Customer Service
http://www.apple.com/support/mac/app-store/contact.html?form=account
iTunes Customer Service Contact
http://www.apple.com/support/itunes/contact.html -
Problem with item and/or data during page-processing-PS/SQL
Greetings!
On my page I have a custom report (from 2 tables) and a small form-field, that adds and edits data in the report. After generating the form with the wizard I added an extra item, to store the id from one of the tables from the report data.
Now, on submit a calculation should take place, that updates data according user input with a procedure in Page-Prosseses:
declare a number;
begin
case :PLATZ
when 1 then a:=100;
when 2 then a:= 50;
else a:=25;
end case;
update TBL_MITGLIEDER set TURNIERPUNKTE = TURNIERPUNKTE + a
where ID_MITGL = :P14_ID_MITGL;
end;
:PLATZ is user selected (1,2,3), :P14_ID_MITGL stores the reference to TBL_MITGLIEDER (and shows the change, when I select another record)
As I understand, that process should also run, when I submit a chance, but nothing happens then.
But when I try to save a new record (which worked without any problems before adding that process), I get this error message:
ORA-06550: line 1, column 64: PL/SQL: ORA-00957: duplicate column name ORA-06550: line 1, column 7: PL/SQL: SQL Statement ignored
Error Unable to process row of table TBL_TURNIERSIEGER.
Then, when I go back into the app-builder and try to run the page again, I get this message:
ORA-01403: no data found
Error Unable to fetch row.
I am not sure, if you guys have all the information you need, to know whats going on. Maybe this has to do with session-id and the whay, items are updated. I hope you can help me.
Thanks, best regards,
tobiFirst can you please post all log file errors
>> I can't really give you a solution or specific recommendation since I did not saw this error yet myself, but on your own risk you can try:
1. You may try to just register 'dts.dll' using regsvr32.exe, but this error may indicate a bigger problem with setup.
If you are running SQL Server 64bit then try running this at the command prompt: %windir%\syswow64\regsvr32 "%ProgramFiles(x86)%\Microsoft SQL Server\90\dts\binn\dts.dll"
2. You can try reinstall from start (In this case you have to make sure that you un-install all)
[Personal Site] [Blog] [Facebook] -
Problem with Gnome3 and/or graphics card Nvidia 8600M GT
Feb 22 07:40:21 localhost dbus[712]: [system] Failed to activate service 'org.freedesktop.Avahi': timed out
Feb 22 07:50:30 localhost kernel: [ 679.031379] gnome-shell[1277]: segfault at 10 ip 00007f3bbd305c0f sp 00007f3b84ff86d8 error 6 in libnvidia-tls.so.295.20[7f3bbd305000+3000]
Feb 22 07:50:31 localhost gnome-session[888]: WARNING: Application 'gnome-shell.desktop' killed by signal
Feb 22 07:50:35 localhost kernel: [ 683.420948] gnome-shell[1300]: segfault at 10 ip 00007f43bc84dc0f sp 00007f43877fd6d8 error 6 in libnvidia-tls.so.295.20[7f43bc84d000+3000]
Feb 22 07:50:35 localhost gnome-session[888]: WARNING: Application 'gnome-shell.desktop' killed by signal
Feb 22 07:50:35 localhost gnome-session[888]: WARNING: App 'gnome-shell.desktop' respawning too quickly
Feb 22 06:52:39 localhost rtkit-daemon[1004]: Successfully made thread 1420 of process 1420 (/usr/bin/pulseaudio) owned by '1000' high priority at nice level -11.
Feb 22 07:52:39 localhost goa[1441]: goa-daemon version 3.2.1 starting [main.c:112, main()]
Feb 22 07:58:22 localhost kernel: [ 1150.316794] CE: hpet increased min_delta_ns to 20113 nsec
Hi,
Here is my /var/log/messages.log output.
Since several days my computer repeatedly restarts programs that require at least a bit memory, such as firefox ('segmentation fault'), skype, virtualbox, generaly gnome 3 environment. Sometimes it happens that the system hangs and I can't do nothing, although I can hear that hard disk is working - at that moment only hard reset helps.
I know that the Dell Inspiron laptops (1720) have problems with Nvidia 8600M GT (the cold solder). Is it like that this time? Or maybe something wrong with the memory, CPU (Core Duo) cache memory?
I will be happy to add any additional information.
Regards,
LukaszDid you update the nividia driver recently?
there are some threads on this
Maybe you are looking for
-
External Hard Drive won't mount - tried Disk Warrior, am backing up as a .dmg...will this work?
Hi Guys, Hopefully someone can help! Fairly desperate situation here... I backed up around 700GB of data to an Iomega external hard drive (supplied by the client), using my Macbook Pro...all was fine when I unmounted the drive at the end of the backu
-
does anyone know if lenovo does 16:10 screens if the customer pays more? i heard some mention of it but it could be old news. i have to say i hate 16:9 screens offered on practically all pc laptops. there is a good 2inches of wasted space on the lcd
-
Java.lang.UnsupportedOperationException when AutoRefresh set to Always
Hi, I am getting above exception (java.lang.UnsupportedOperationException) when I change the "AutoRefresh" property of view object to "Always". The exception comes at: at oracle.jbo.server.ViewObjectImpl.executeQueryForCollection(ViewObjectImpl.java:
-
Trouble Downloading The iPod Software, Error 1418, Error 1348
My iPod every so often crashes and erases my Music and Videos. Prompts me to "Connect to your computer Use iTunes to restore". I come home from school, I hope on my computer and connect the USB to my iPod open iTunes click the restore button, Ask me
-
Inserting/manipulating PDF in Flex 3 AIR project?
I've read as much as I can find about dropping a PDF into my Flex 3 AIR project, but the information is scarce and I understand it's a very new (not fully baked) feature. Can anyone describe what component to use to drop a PDF into my AIR project? I