Problem with SPAU Transports after Upgrade and after applying SAPKW70016

Dear All,
we copied old dev to new QA, upgraded new QA, then copied new QA to new DEV.
did the SPAU adjustments in DEV.  At that time DEV SAP_BW version was SAPKW70015.  After that we applied SAPKW70016.  Now we're having problems with the SPAU transport because of the application of SAPKW70016. 
Requested to kindly suggest ASAP.
Thanks & Regards
janardhan Kumar K

Hi,
Could you please to be more specific with the error ? Please check the log e send us the message error that is happening during the transport.
Thanks,
Walter Oliveira.

Similar Messages

  • I'm using mac with the newest operating system (snow leopard 10.6.7). since I've updated to Firefox 4 It doesn't display Hebrew fonts- I didn't have any problems with it before the upgrade and in safari I don't have this problem.

    Hello, I'm using Mac with the newest operating system (snow leopard 10.6.7). since I've updated to Firefox 4 It doesn't display Hebrew fonts… I didn't have any problems with it before the upgrade and in safari I have no problem with it. please help me- I don't like to use safari a my browser...

    elly903 wrote:
    Before commenting - I CANNOT install Mavericks because it'll mess up the versions of Filemaker Pro and Quicken that I use regularly...
    Quicken 2007 for Intel (Snow Leopard, Lion, Mt. Lion and Mavericks) for $15:
    http://quicken.intuit.com/personal-finance-software/quicken-2007-osx-lion.jsp
    It will input your Quicken PPC data file directly if it was Quicken 2005 through 2007.  If older you need Quicken 2006 or 2007 PPC first to convert your data file; and this update must be done BEFORE you upgrade to Mavericks:
    http://quicken.intuit.com/support/help/patching/quicken-2006-manual-updates--mac -/GEN82200.html
    Filemaker Pro PPC (in this case 7) running in Snow Leopard Server installed into Parallels for use in Lion, Mt. Lion and Mavericks:
                                  [click on image to enlarge]
    Snow Leopard Server: 1.800.MYAPPLE (1.800.692.7753) - Apple Part Number: MC588Z/A (telephone orders only)
    This solution allows you to run your Photoshop Elements in Mavericks concurrently with Filemaker Pro PPC.  Mavericks is a free download.

  • SERIOUS Problem with 10.5.5 upgrade and receiving POP3 emails their

    I upgraded to 10.5.5 last night. I am now unable to POP my POP3 email messages from my Network Solutions account. I have talked extensively to Networks Solutions, and I am convinced it's not their problem. I AM able to retrieve the messages using Outlook 2003 on XP. I AM able to retrieve these messages on my other Mac using 10.5.4. This is pretty strong evidence that it's some sort of an issue with Mail in 10.5.5. Note I can send email via smtp fine.
    HELP ....

    Hi All,
    I'm getting the same problem - Mail hangs while fetching new email - usually hangs on the last email. This happened while running 10.5.4 and the 10.5.5 update didn't help.
    Nor did vacuuming the Envelope Index or removing them and rebuilding.
    I'm seeing this is the system log:
    Mail[855] prepareForSave:: save for NSSQLCore 0x17b5efe0 is already in progress
    during invocation of -[MessageRouter routeQueuedMessages]
    Stack Trace: (
    2495115595,
    2416107067,
    2517328129,
    2517326500,
    2517235689,
    2517234566,
    2517309445,
    4819744,
    4245791,
    4147127,
    2495138429,
    2495136872,
    4027592,
    4031370,
    2417900461,
    2417899348,
    2421450485,
    2421450162
    So far, no luck at Google.

  • SERIOUS Problem with 10.5.5 upgrade and receiving POP3 ADDENDUM

    See my posting below. I am running mail 3.5 which has the problem. I wonder if I can test my theory by reverting to the prior version of mail 3.3 while still running current OS 10.5.5. I think I can get to in via Time Machine. Is there a problem if I try to do this?

    Sorry, but you cannot do this.
    Since I am having not issues with receiving POP email (or any other type), I would be good to have further info. When you open and observe the Activity monitor in Mail, was what is reported when trying to connect?
    Opening the Connection Doctor, what does it report for this account?
    Ernie

  • Had a problem with the last firmware upgrade and now have a delayed startup

    I made the mistake of doing the firmware flash while the MBP was docked. I don't thing it was successful although it shows the right number. My startup time is about two minutes which is unusual as it used to be super fast (using an SSD). Any ideas?

    See this older post from another forum member Zevoneer covering the different methods and software available to assist you with the task of copying content from your iPod back to your PC and into iTunes.
    https://discussions.apple.com/thread/2452022?start=0&tstart=0
    B-rock

  • Is anyone having problems with the battery drains quickly and the iphone4 heats up in use and in charging after upgrading to 5.1.1?

    Is anyone having problems with the battery drains quickly and the iphone4 heats up in use and in charging after upgrading to 5.1.1?

    I have had the same problem but I seem to be getting somewhere to fixing it!!! My battery was going down at 20% an an hour now its 10% with constant use and 5 in standby !!! So improvement all round
    First I did a restore then I drained the battery i started to charge it and when it came on I turned the phone off completely and let it charge to 100% I then left it for a couple of hours on charge at 100. I saw no improvement after 1st drain so I repeated the drain battery and charge steps again with the phone turned off when charging and have seen a very big improvement. I am going to do it again tonight and hopefully problem solved!!!!
    The next issue is iMessage as that's playing up and wifi drop out
    Good luck

  • I have a problem with Adobe Creative Cluod. Basically after installing the application when I open it I do not charge adobe products but remains all white screen. I tried to uninstall it and install it several times but it does not work.  What should I do

    I have a problem with Adobe Creative Cluod. Basically after installing the application when I open it I do not charge adobe products but remains all white screen. I tried to uninstall it and install it several times but it does not work.
    What should I do?

    Hi Anto2211,
    Please follow the thread: Black screen CC where this issue is already discussed and resolved.
    Let me know for any further query.
    Thanks,
    Ratandeep Arora

  • Problem with"Evaluate User Policies"sch task after the upgrade OIM R1 to R2

    Problem with "Evaluate User Policies" scheduled task after the upgrade from OIMg R1 to OIM 11g R2
    After the upgrade process is completed we are having issue with Access policy not triggering if rule is set to custom attribute
    - We had a Rule with custom attribute (Policy='Full-Time') the value gets populated by event handler which triggers the access policy in OIM 11g R1.. which worked fine in OIM R1
    After the upgrade the value is getting populated but even after running "Evaluate User Policy" the Access Policy is not getting triggered.
    We tested creating a rule with other custom attribute,policy does not trigger even after running Evaluate User Policy schedule Task in this case too
    but if we try creating rule with OOTB attributes(Country='US') it works fine the access policy got triggered after running Evalute User Policy
    One more issue we observed is
    - Evaluate User Policy value usr_policy_update is not updated still set to '1' even after the Access policy got triggered (as it worked when rule is set to OOTB attribute)
    I believe after the evaluate user policy gets triggered for a user it should update the value from '1' to '0')
    Please let me know if you have any idea..Thanks!

    well, I overcame the issue by 'fooling' the installer: on second node, change the scan ip address to point to something else (ie, different ip address to the scan in the first node, cleanup then rerun root.sh, it went past the trouble stage, then I still have problem later at the time database creation. I think scan ip address has to be setup correctly (round robin thingy)
    This is how i did the cleanup before rerun root.sh
    /u01/app/11.2.0/grid/crs/install/rootcrs.pl -verbose -deconfig -force

  • I have a macbook pro 1.5 years old ver10.7.5 and now having a problem with having to manually force quit after a hour or so of use to clear up memory(unit slows down) should I up grade iso if so to what

    I have a macbook pro 1.5 years old ver10.7.5 and now having a problem with having to manually force quit after a hour or so of use to clear up memory(unit slows down) should I up grade iso if so to what and what is the correct procedure?  Rick

    To determine if it is, boot into Safe Mode and see what happens. http://support.apple.com/kb/HT1455
    In the Activity Monitor, what are the Page Outs and Page Ins?

  • Problems with a new IP phone 7906 after factory reset

    Hi Guys
    I am currently having problems with my new IP phone 7906 after doing factory reset and here is a video of it:
    http://www.youtube.com/watch?v=vvCLtwIAwVw
    I used this command I found on the net:
    Hold down
    while plugging in the phone and keep holding it until the message waiting indicator (red light) starts blinking.  Then
    release # and type 123456789*0# in sequence.
    I was trying to switch my phone to sip and it also dont want to take tftp setup either.

    Tim,
    Found this on the net
    http://www.cisco.com/en/US/ts/fn/620/fn62949.html
    Might be woth giving it a go
    6.Pull power on the phone (even if power is PoE).
    7.Hold down the # key on the phone.
    8.Continue holding down the # key and re-apply power.
    9.While still holding the # key wait for the Message Waiting Indicator (MWI) light on the handset to start flashing.
    10.Once the MWI light is flashing, release the # key and enter the following sequence exactly on the keypad:
    3491672850*#
    Once this sequence has been entered on the IP Phone, if all the network criteria above have been met, it should begin its recovery process. This process can take up to 15 minutes to finish. The phone may appear to be doing nothing during this time. However, if the phone does not recover after 20 minutes then it is possible that the recovery is stuck. In this case, re-examine your network and verify that steps 1-4 are in place, then re-issue the factory reset sequence.
    * Note: The factory reset sequence is a way for a phone to clear flash and still upload to a valid firmware image. This is facilitated by the termxx.default.loads file, but requires that the image files listed in the termxx.default.loads file are available in TFTP for the phone to download. Open the termxx.default.loads file in any text editor. This loads file is essentially just a packing list showing all the OS and application files the phone needs to function. The files include a cnu, cvm, dsp, app and jar files. Please make sure that these files as listed in the termxx.default.loads file are in TFTP. ("xx" will be either "06" for the CP-7906G model, or "11" for the CP-7911G model.)
    Additional Diagnostic Steps:
    - Try a hard-coded IP address as a test to see if this resolves the upgrade failures. If it does, and the number of failing IP Phones is relatively few, this procedure may be the most expedient. After the IP Phone upgrades successfully, reconfigure the IP Phone to use DHCP.
    - Try putting the phone on a hub or a different switch and see if this helps change the startup timing enough so that the upgrade completes successfully.
    Regards
    Alex

  • Problems with System Update 3.14.0019 after installation SP2

    Have you encountered problems with System Update 3.14.0019 after installation SP2 for Windows Vista?
     After this upgrade I view  this error: "An error occurred while gathering user information."
    Thanks for the help

    A known issue.  It wasn't supposed to be supported until SP2 is RTM.  However, look at the stickied post in the forum for some bad news about SU.
    x61s

  • The problem with forecast reports in SCOM 2012 after integration with VMM 2012

    Hello.
    I have problem with forecast reports in SCOM 2012 after integration with VMM 2012. All other reports (not forecasting) works fine. For example, report “Host Group Forecasting” don’t work. The report is generated, but I have error: “Subreport
    could not be shown”. I find only errors in SQL Server Reporting logs like this:
    library!ReportServer_0-13!1758!06/26/2012-18:26:23:: i INFO: RenderForNewSession('/Microsoft.SystemCenter.VirtualMachineManager.2012.Reports/Microsoft.SystemCenter.VirtualMachineManager.2012.Report.ForecastHostGroup')
    processing!ReportServer_0-13!1758!06/26/2012-18:26:28:: e ERROR: Throwing Microsoft.ReportingServices.ReportProcessing.ReportProcessingException: , Microsoft.ReportingServices.ReportProcessing.ReportProcessingException: Не удалось выполнить
    запрос для набора данных "DiskSpaceUsageForecasting". ---> Microsoft.AnalysisServices.AdomdClient.AdomdErrorResponseException: Execution of the managed stored procedure GetTimeSeriesForecast failed with the following error: Exception has been thrown by
    the target of an invocation..
    Query (5, 58) Parser: The syntax for '6' is incorrect.
       at Microsoft.AnalysisServices.AdomdClient.AdomdConnection.XmlaClientProvider.Microsoft.AnalysisServices.AdomdClient.IExecuteProvider.ExecuteTabular(CommandBehavior behavior, ICommandContentProvider contentProvider,
    AdomdPropertyCollection commandProperties, IDataParameterCollection parameters)
       at Microsoft.AnalysisServices.AdomdClient.AdomdCommand.ExecuteReader(CommandBehavior behavior)
       at Microsoft.AnalysisServices.AdomdClient.AdomdCommand.System.Data.IDbCommand.ExecuteReader(CommandBehavior behavior)
       at Microsoft.ReportingServices.DataExtensions.AdoMdCommand.ExecuteReader(CommandBehavior behavior)
       at Microsoft.ReportingServices.OnDemandProcessing.RuntimeDataSet.RunEmbeddedQuery(Boolean& readerExtensionsSupported, Boolean& readerFieldProperties, List`1 queryParams, Object[] paramValues)
       --- End of inner exception stack trace ---;
    The Russian string “Не удалось
    выполнить запрос для набора данных "DiskSpaceUsageForecasting"” is translated to “Could not execute query for data set "DiskSpaceUsageForecasting"”.
    I have clean installation SCOM 2012 RU1, VMM 2012 RU1. Integration SCOM with VMM work fine.
    SQL collation for all SQL DB instances (SCOM and VMM and SCOM reporting) – “SQL_Latin1_General_CP1_CI_AS”
    SQL Analysis service: SQL collation – “Latin1_General” ; language for the server – English (United States)
    I think the problem in regional settings. By my opinion there are two possible mistakes:
    SQL collation  for all SQL DB instances. May be need use “Latin1_General_CI_AS”
    as provided by
    http://blogs.technet.com/b/momteam/archive/2012/05/25/clarification-on-sql-server-collation-requirements-for-system-center-2012.aspx
    Need change regional setting. Question is for what (OS regional setting, SQL Analysis service settings,…) ?

    Error: Subreport could not be shown
    Opening a report for Client Security might result in the following error being displayed in one or more areas of the report: "Error: Subreport could not be shown."
    Background
    There are two possible reasons for this error:
    1. Wrong location   The reporting server is pointing to the wrong computer running SQL Server or a SQL Server instance.
    2. Insufficient permissions   The account configured (in SQL Server Reporting Services) to connect to the reporting database does not have appropriate permissions for the database.
    Solution
    To determine which reason is causing the error, attempt to directly open the subreport reporting the error, by clicking the name of the subreport.
    If the reporting server is pointing to a wrong location, the report displays an error similar to the following: 
    Error message
    An error has occurred during report processing.
    Cannot create a connection to data source 'SystemCenterReporting'. Cannot open database "SystemCenterReporting" requested by the login. The login failed. Login failed for user username.
    To verify the correct SQL Server computer and instance path
    In Report Manager, navigate to the report generating the error and click the Properties tab.
    Click Data Sources and under a Shared data source, note the path.
    Open the reporting Web site. If you chose the default virtual directory for reports, the URL is: http://hostname/Reports/
    If you chose to secure the viewing of reports with HTTPS, the URL is: https://hostname/Reports/
    Click SCDW.
    In the Connection type list, ensure that Microsoft SQL Server is selected.
    In the Connection string box, ensure that the correct SQL Server computer and instance name are entered.
    Note:
    A period (.) denotes the local computer.
    If the account has insufficient permissions, the report displays an error similar to the following: 
    Error message
    An error has occurred during report processing. (rsProcessingAborted) Query execution failed for data set 'DSDashboardComputersTrend'. (rsErrorExecutingCommand) EXECUTE permission denied on object 'prSAS_UX_DashboardComputersTrend', database 'SystemCenterReporting',
    schema 'dbo'.
    To determine if you are experiencing the SQL Server permissions issue
    Open the reporting Web site. If you chose the default virtual directory for reports, the URL is:http://hostname/Reportserver/
    If you chose to secure the viewing of reports with HTTPS, the URL is:https://hostname/Reportserver/
    Click Microsoft Operations Manager Reporting, click Microsoft Forefront Client Security, and scroll to DashboardComputersTrend.
    Click DashboardComputersTrend.
    If you are experiencing a SQL Server permissions issue, an error similar to the preceding error appears.
    To grant permissions to the SQL Server computer
    1. In Report Manager, click SCDW and note the account in the Connect using section. This is the account under which the database is contacted.
    2. On the server with the System Center Reporting database, start SQL Server Management Studio.
    3. In the tree, expand Security, and then expand Logins. Do one of the following:
    If the user account is listed, right-click the account, click Properties, and then go to step 5.
    If the user account is not listed, right-click Logins and choose New Login.
    4. In the Login name box, enter the user account (domain\username).
    5. In the Login Properties dialog box, click User Mapping, and then under Users mapped to this login, select the System Center Reporting check box.
    6. Under Database role membership for: System Center Reporting, select the db_owner check box, and then click OK.
    Thanks,
    Yog Li
    TechNet Community Support

  • I bought an app for my iphone version 3.1.3 and it is written in the requirements that it is compatible with IOS 3 or later and after installing it doesn't work.i bought it from the apple store.

    i bought an app for my iphone version 3.1.3 and it is written in the requirements that it is compatible with IOS 3 or later and after installing it doesn't work.i bought it from the apple store

    You could try reporting the problem to iTunes store support here: http://support.apple.com/kb/HT1933.

  • I cant open Tools in Menu of Mozilla. Even after upgrade and re install.

    I cant open Tools in Menu of Mozilla. Even after upgrade and re- install.

    Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
    * Don't make any changes on the Safe mode start window.
    See:
    * [[Troubleshooting extensions and themes]]
    You can also try:
    * http://kb.mozillazine.org/Corrupt_localstore.rdf

  • Problem with battery running down more quickly after downloading OS6 to 3GS iPhone

    Problem with battery running down more quickly after I downloaded OS6 to 3GS iPhone.

    gdgmacguy
    I guess I should have asked for the "definitive" fix. I read several "fixes" but it seems no one knows if Apple has a definitive fix. Kind of like going into an Apple store and getting three different answers from three different reps. At least they are not rude and no, I don't have a problem searching the forum.
    <Edited by Host>

Maybe you are looking for