Problem with WRT54G ver 6

hi,
my laptop is nt able to detect the wireless router. all the lights in the router turns green when powered even though it has only 1 laptop connected to port 4 .
any body knows what the deal is. when i type in cmd > ipconfig \all and it does not show the wireless router.
whats the problm with this. if any body can help , it would be great.
can ny body help me with the telephone numbers of the technical cupport in bangalore , india
rajdwip

Hi...
Try resetting the router to factory defaults. To reset the router ....press and hold down the reset button on the router for 30 seconds. After reseting the router...unplug the power to the router for 30 seconds and then connect the power. When all the lights on the router as steady, try reconfiguring the router from start.

Similar Messages

Wireless Problems with WRT54GS Ver.4

I have 3 computers in the house on a wireless connection and one wired. Just recently all 3 wireless connections are not working properly. The computer i use has not seen any problems it's connected directly to the router through a network cable. Without changing any of the settings on either the computers or the router they will not connect to the internet. They are all 3 connected tot he network but I am unable to connect to the internet on them, or create an internet connection.

it internet add is not all 0's. The problem isn't with the wired connection. it's with all the wireless connections. I configured the connections to begin with and never had any problems outside of low signal strengh with any of the 3 connections. but just recently i can not connect to the internet on any wireless connection. None of the settings on the router or computers have changed since this problem has occured. I'm using the latest firmware. I've reset the router and still no change in the situation. all 3 computers using wireless connect to the network fine but when i try to setup an internet connection it doesn't add it into the "network connections" folder. I'll click "setup" under "connections" inside internet settings in IE, and click "connect to the internet" , "set up connection manually", "connect to a broadband connections that is always on" and "finish" uasually this is where the internet connection pops up in the "network connections" folder but nothing happens...?

Big problem with WRT54G ver.6

I get home after purchasing this router, I start to hook it up exactly as it said to do, and the ethernet light on my modem i suddenly blank...even though it was flashing a second before. After 20 mins it finally comes back on out of nowhere. However, I am unable to do anything because I have still had the constant problem of my router's power light flashing yellow over and over and not stopping. I have tried everything I can think of and it just keeps flashing, and my computer is unable to detect it.
If its needed I use Verizon DSL and have a Westell WireSpeed modem.

I tried the easylink, however it fails to do any good because it still fails to detect the router despite anything I do. The power light flashes nonstop regardless of what I do, all eithernet ports and the internet one are constantly on, but the WLAN never lights up.(the internet ones are on even if no ethernet cables are connected.

Pls help me.i have a problem with WRT54G wireless router.

Dear all, Now i got face some problem with WRT54G wireless router.The problem is after i connect to the internet...the wireless will automatic drop..is that any ppl here got face this and got any solution to solve it...?thanks for sharing..

hi...logon to router's setup page and try changing channel to 11, go to advanced wireless settings, try changing transmission rate to 54Mbps, beacon interval to 50, fragmentation and RTS threshold to 2304, also try upgrading latest firmwar on the router...check whether it maks any difference or not and let me know.

Network cable unplugged problem with WRT54G

I just got a WRT54G wireless router recently, and experienced some problems with it. There are 5 notebooks in my network using wireless card and 2 PCs connect to the router through cables. The router is with ver 7.00.1 firmware.
The router is working fine, the problem is sometimes it will show "Network cable unplugged" on my PC, and the whole network will be interruptted, the network will be resumed in few seconds and all machines need to get IP from the DHCP server again. It's quite annoying to be disconnected from middle of the work. I don't know what is the cause, seems like the router is re-reading it's configuration. I have tried to refresh the fireware but with no luck. Someone else got this problem before? anyone has a solution for this? Thanks a lot!
Regards,
Leo

Try the following tips to resolve your problem:
Disable the Ethernet network adapter if you are not using it. This applies, for example, when running a WiFi home network with computers that have built-in Ethernet adapters. To disable the adapter, double-click the small Network Cable Unplugged error window and choose the Disable option.
Check both ends of the Ethernet cable connected to the adapter to ensure they are not loose.
Replace the Ethernet cable with a different one to verify the cable is not damaged.
Update the network adapter driver software from the manufacturer's Web site.
Change the Link Speed and Duplex settings (using Device Manager) to use "100 Mbps Full Duplex" or "10 Mbps Full Duplex" instead of Auto Detect.
Replace the Ethernet network adapter
Good Luck,
Ttech

Problem with prod. ver. explosion to production order

Hi
I have problem with production versions. I have FERT with 3 production versions. Additionaly we have Z-program (on Z-table) which control parameter sold to party (from sale order) with production version. So after MRP I see in planned order right production version for example 3 - field PLAF-VERID; in master data in planned order I see right alternative BOM and routing; but when I make a conversion to production order I see that system always explode 1st version; additionaly in planned order in components (button) I see 1st pr.ver (1st alternative BOM) and in Bill of Material (it seems like to manually expolding BOM) I see right version??? But it couldn't be like this that to have right data I need to go to transaction MD12, explode BOM manully, save and after that make a prod. ord.
I would like to system explode BOM according to production version (field VERID) already in planned order; so after that it should be that when I will converted it to production order I should have right BOM and right routing from production version signed in planned order.
I know it sounds complicated Add. in configuration all parameters are set right to explode BOM etc. etc. system version: 4.7
Thanks and regards. Joanna
Additional info: I cancel this question cause problem is in Z-program; becuase when according to Z-table system change input in field VERID for system it is only "digital" not parameter for which system should explode right BOM; sorry for disturbing, we need to change Z-programm; I do not know how but maybe any function module can help - we will think. Regards
Edited by: Kostkaj on Aug 17, 2010 10:25 AM

HI
Check this link and find valuable suggestion by Mr Mangalraj regarding selection of PVs
Produciton version selection in MRP
Regards
Anupam Sharma

Problems with WRT54GS and EasyLink after adding Comcast Digital Voice.

I had a working network. Cable modem (Comcast), WRT54GS, 2 wired PCs (one XP/SP3, one Vista Home Edition SP1), 2 wireless laptop PCs (one XP/SP3, one Vista Home Edition SP1) and a HP OfficeJet 7210 printer (connected to WRT54GS as network printer). Everything was fine and worked.
Then, I added Comcast Digital Voice. Obviously, they switched the cable modem for a new cable modem with the phone service option. Now, I can't print to the OfficeJet from the wired Vista PC, and EasyLink displays "initializing" for as long as I'll wait (5+ minutes).
I finally have to kill EasyLink from the TaskManager. Any help or ideas appreciated!
Solved!
Go to Solution.

I solved the problem. It turns out the new cable modem and problem with EasyLink initializing were "red herrings".
The problem turned out to be a classic network problem! The hard-wired Vista PC had the wrong IP address. The wireless XP PC had the printer configured by network name instead of network (i.e. IP) address.
When I deleted the printer on the Vista PC and re-added it with the correct address everything worked fine.
Apparently the printer got a new IP address from the server on the WRT54GS after the installation of the new modem. Also, it looks like Vista doesn't report a communication error for a network printer, but does for a USB direct connect.

File and print sharing with wrt54g, ver. 6

computers connected to my wrt54g, ver. 6, router (firmware ver 1.01.1) cannot see each other's shared files although they can all share the same internet connection just fine. file and print sharing has been set up on each (they were connected to a wired router before i purchased the wrt54g and they saw each other and shared files, no problem). how can i share files through this router? what went wrong?

Are you running software firewalls on any computer? Has the LAN IP network changed (e.g. it was 192.168.0.* before and now 192.168.1.*)?

Problems with WRT54G and Call of Duty 4 hosts....XBOX360

I have a WRT54G wireless router and an xbox360 hooked up wirelessly to it using the wireless adapter made my microsoft for the 360. The problem is that it is nearly impossible for me to connect to ANY host at all. My internet works fine and I dont have this problem with other games. I'm wondering if anyone can help me out with this. My isp is Verizon DSL, i have a Westell 5100 modem, that is about all else I can think of that may have any importance. Thank you for the help in advance.

Check the firmware of the router ... if possible upgrade the firmware .... Also try to forward the ports on the router setup page ..

Problems with WRT54G

this is my problem i have the wire from my modom to my router the internet light is on i have a cable hooked in to the back of the linksys router in the #1 port, the cable in #1 port is then hooked to my desktop pc . i have a WLAN light on . ok know for the fun part i get a great signal on my laptop so it is seeing the router but will not connect to the internet.i have tried everything i can think of and then everything some websites have said but nothing works so can you tell me what you think is the problem or if it is operater error

I have the same problem with a slight difference - my desktop is connected to the WRT54G through a LinkSys WUSB54GC Adapter - it runs fine. I have the same problem with a laptop - it can see the router but cannot connect to the internet. I turned of security settings on the laptop, and have defined a unique SSID. The laptop continues to see the router but not the internet! The laptop has been able to successfully connect to a number of different wireless routers. I have tried every logical router setting to see if the laptop can see the internet and nothing helps. I restored to factory settings before I defined the new SSID. Help!!!

Problems with wrt54gs v. 06

I keep losing internet acess on all computers with this router. Now when I hook my old router back up that is a linksys b router it works fine but then i hook the g router back up no internet. I have did the powercycle and it didn't work. I notice the G routers been having this problem.

Ok it keeps disconnecting from my the computer its hooked up too. And I updated the firemware it stayed on for one day. Then i powered up the computer the next day it wouldn't work. and this is all the computer the wired one and the wireless ones (I have a laptop and another desk top connected wirelessly). It just annoying that I have to keep hooking up the b router cause the g one keeps cutting off. I have Windows XP on all the computers. I got the Usb adaptor on the desktop and My dell has the Intel Pro Wireless 2200 b/g card. once I get connection on my computer that has the router hooked up to it I have no problems with the wireless ones.

Connection Problems with WRT54G V6

Hey Guys,
This is the problem that im faced with.
For the last few weeks my router has been having problems with the internet connection. For some reason there is no internet connection everytime i turn my computer back on after a session. To resolve this problem i perform a factory resest and then unplug my modem from it's power source leave it for 30 seconds and then connect it again... and this seems to work all and good for that period i use the computer for. But when i turn the computer back on the next day the internet connection is lost.The modem im using is a Motorola SB5100
Anyone got any ideas on how to resolve this?
Thanks
Message Edited by Ramadge on 03-02-2009 09:33 PM

You need to upgrade your router's firmware, reset it and re-configure it...
Download 1.59 MB Firmware...
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Problems getting a connection with WRT54G Ver. 8

Okay.. This may be a little long.
I had my router set up for about 2 years now. It worked fine up until 2 days ago. I have a WRT54G V8 router, with a Belkin wireless receiver for another desktop computer. I have tried using the 192.168.1.1 website to set up on my wireless computer to try and set up the IP address, but it does not seem to be working at all. The IP remains to be 0.0.0.0 and would not change after changing the MAC address, and using Release/Renew option. The desktop computer that the router is hooked up to doesn't even recognize 192.168.1.1 website into the browser. I have tried reconnecting the router, as well as the Broadband modem that we have and nothing seems to get the connection to my other desktop. Can anyone help me get my connection running again? It would be greatly appreciate.

Your Modem should be connected to the Linksys Router on the Internet Port and then you need to connect your Computer to the Linksys Router on the LAN Port 1.... Then Connect the Power to the Router.... Check the Light Status (Power, WLAN, Port no.1 and Internet) all this lights should be Lid...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

File and Printer Sharing Problem with WRT54G

I am currently having problems sharing files over my network. My setup consists of:
3 laptops (wireless)
1 desktop (wired)
WRT54G V6.0 router with firmware version 1.00.9.
All of the computers have File and Printer Sharing enabled, unique names, and are on the same workgroup. However none of the computers can see one another. When I try to view workgroup computers for my network places, the explorer window stops responding for about 30 sec. and then spits out a dialog with the error:
"Workgroup is not accessable. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.
The list of servers for this workgroup is not currently available."
I think that this problem has something to do with the router, as I have been successfuly sharing files and a printer with these settings using a microsoft 802.11b router for over a year. After purchasing the linksys and swapping it out with my old router, filesharing no longer functions.
I have spent a little time browsing the forums and have seen other posts from people with simmiler problems, but was unable to find any solutions.
Any help would be much appreciated.
Thanks.

I'm having the same problems as you are, I have 2 computers on wired the other wireless the router is in between and I can't access from either side, although I can ping and remote connect but just cannot share files across the network. I have looked all over the forums too and there saying to ditch linksys and do something else.
Its not you thats caused this it is the firmware and the router that have the problems.
My Specs:
WRT-54G
v5.0
That new firmware update 1.00.9 just isn't working right. I might downgrade my fireware to fix this problem.
Message Edited by justin2006 on 09-26-200612:24 PM

Admin problem with WRT54G

I am logging into my WRT54G to try to upgrade my firmware. The problem is that when I log in, I get a error on the page and it will not bring up any of the links or icons that I would use to go to Administration or check my wireless or anything. Does anyone even know where to start with this? I am using XP Pro and IE6 SP2.
Any ideas?
Thanks,
Derek

If you are getting a 401 error, the router most likely did not accept your user name and password. The defaults are: user name is left blank, and password is "admin" (with no quotes). If you changed these, then you will need to enter whatever you changed them to. If you cannot remember what you set them to, then the only other option is to reset the router to factory defaults. This will reset the user name and password to the values noted above.
Sometimes this problem is caused by communication errors between the computer and router. To correct this, do the following:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall. Note that some Zone Alarm users have had to uninstall the firewall to get it turned off.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.

Problem with WRT54G ver 6

Similar Messages

Maybe you are looking for