Problem with zone alarm.

Hi everyone, this is the first time I get a Toshiba Lap top and I had a problem after installing Zone Alarm PRO edition. The module is just not starting, the icon appears but nothing else happens, I already tried with an older version and cleaning the system with Tune Up. I was checking in some forums I found some information about that Zone Alarm is not compatible with some Toshiba Satellite models (mine is L305-SP6912R).
Can some one please help me to find what is the problem, because I really need to use Zone Alarm on my LapTop.
Thanks and sorry for my bad english.

I'd say you're in the wrong forum. Try the Zone Alarm folks.
ZoneAlarm User Forum
Good luck!
(Be sure to come back here with Toshiba problems.)
-Jerry

Similar Messages

Firefox 5 will not start with Zone Alarm Ver 10.0.240.000

Firefox updated yesterday and now it will no longer start, it looks like the probem may be with Zone Alarm Forcefield. Does anyone have any ideas how to get Firefox 5 to tun under Zone Alarm Extreme Security? Thanks

Hi,
I'm running Win7 x64 with ZoneAlarm Extreme Security 10.0.241.000
I had the same problem with Firefox 4. After turning off ForceField Toolbar, it started working fine.
Then I updated to Firefox 5 and it wouldn't start, instead it was showing an error message from ZA...
I searched mozilla support and followed the instructions here: http://kb.mozillazine.org/Browser_will_not_start_up
on the topic"Firefox does not start after updating with ZoneAlarm ForceField enabled".
The correct instructions for this ZA version should be: "'''Internet '''-> '''Web Security '''-> '''Settings''', and click '''Clear Virtual Data'''"
After that I could open Firefox again! Then I realized it was still version 4...
I installed the update, and everything went smooth. Checked again if Forcefield toolbar was inactive (it was) and opened a few pages, closed Firefox and opened again. After a while it wouldn't open...
AGAIN the "Clear Virtual Data" did the trick...
This time I clicked on '''Settings '''(next to "Clear Virtual Data") -> '''Advanced Settings''', and turned off "'''Enable Virtualization'''".
Until ZA get a fix for this, either we turn it off or clear virtual data every few moves...
Working fine.
Best regards

Ical on multiple computers - There was a problem with an alarm

I set up my iCal to sync between my home computer and a Mac at work on my desk. Whenever I schedule an important appointment I schedule a reminder that runs a script that says "15 minutes to your appointment" or something similar.
The scripts are stored on the hard drive of my laptop at work and it works pretty well there. But on my home machine every day I get "There was a problem with an alarm" dialog boxes because it cannot find the script.
I tried working around this by storing the scripts on my iDisk drive, but then the proper functioning of the calendar and the reminder depends on whether or not the Internet connection is up and the iDisk is online.
Any recommendations for how I can eliminate the issue? I think the solution probably lies in storing the scripts in a similarly labeled folder on both machines, e.g. /Users/mpender/Documents/Speech, but that doesn't quite work for me. Also, it would be highly desirable to have the speech folder sync so that changes like the introduction of new reminder messages would appear in both places.
I'm open to suggestions, but there has to be some way to address this using relative path name addressing.
Thanks, Mike

I found that this works reasonably well if I store the speech scripts in the iDisk and turn on iDisk syncing to keep a local synchronized copy of the speech scripts.

Problems with Zone based Firewall and mtr (mytraceroute)

We are using ZFW on an ASR1001 and have experienced a problem: when I try to use mtr (mytraceroute, see
http://en.wikipedia.org/wiki/MTR_%28software%29), I am getting packetloss on all hops between the source and the destination. e.g.:
<code>
                                                                                                                   Packets               Pings
Host                                                                                                            Loss%   Snt   Last   Avg Best Wrst StDev
1. Stuttgart-I28-1.belwue.de                                                                                    100.0     8    0.0   0.0   0.0   0.0   0.0
2. Stuttgart-AL30-1-gi0-0-0-3.belwue.net                                                                        100.0     7    0.0   0.0   0.0   0.0   0.0
3. Karlsruhe-RZ-1-10GE-0-1-0-1.belwue.net                                                                       100.0     7    0.0   0.0   0.0   0.0   0.0
4. Karlsruhe1-10GE-4-0-0.belwue.net                                                                             100.0     7    0.0   0.0   0.0   0.0   0.0
5. Mannheim1-10GE-3-0-0.belwue.net                                                                              100.0     7    0.0   0.0   0.0   0.0   0.0
6. Frankfurt-DECIX-1-10GE-0-0-0-0.belwue.net                                                                    100.0     7    0.0   0.0   0.0   0.0   0.0
7. de-cix20.net.google.com                                                                                      100.0     7    0.0   0.0   0.0   0.0   0.0
8. 72.14.238.230                                                                                                100.0     7    0.0   0.0   0.0   0.0   0.0
9. 72.14.239.62                                                                                                 100.0     7    0.0   0.0   0.0   0.0   0.0
10. 209.85.242.187                                                                                               100.0     7    0.0   0.0   0.0   0.0   0.0
11. ???
12. ???
13. ???
14. bk-in-f94.1e100.net                                                                                           0.0%     7   20.0 20.6 20.0 21.2   0.4
</code>
So it seems that the Firewall on my asr1001 is throwing away all packets with ttl-exceeded coming back from hops in between, they have another destination address.
At the moment I am inspecting all kind of traffic from my network outgoing:
ip access-list extended 101
permit ip any any
class-map type inspect match-all cmap1
match access-group name 101
policy-map type inspect pmap1
class type inspect cmap1
inspect
etc... (zones, zone-pair in-out with policies applied)
So I tried to let pass all icmp-traffic from the outside to my network:
class-map type inspect match-all cmap_icmp
match protocol icmp
policy-map type inspect pmap2
class type inspect cmap_icmp
pass
etc... (zones, zone-pair out-in with policies applied)
So this has no effect, but I tested and I could figure out, that when I pass all icmp-traffic from my network to the outside, THEN mtr does work.
BUT then normal ping does not work anymore, because it will not be inspected any more.
But I want to have a secure Firewall with inspecting echo-replys and working mtr anyway.
Has anyone the same problem or can even solve this issue?
Thanks in advance,
Stefan

Hi Andrew, thanks for Your answer...
So I have now:
class-map type inspect match-any cmap_icmp
match access-group name icmp_types
ip access-list extended icmp_types
permit icmp any any ttl-exceeded
PMAP IN--> OUT
(don't be confused, my "vlanxxx_pmap_in" is the pmap FROM my network TO the outside...)
policy-map type inspect vlan664_pmap_in
class type inspect vlan664_cmap_in   (this is an extended ACL "permit ip x.x.x.x any")
inspect
class type inspect ipsec_cmap_in (this is because I have problems with VPN when inspected, another problem...)
pass log
class class-default
drop log
PMAP OUT-->IN
policy-map type inspect vlan664_pmap_out
class type inspect cmap_icmp (here comes the "ttl-exceeded"-ACL)
pass log
class type inspect vlan664_cmap_out (some open ports for some clients)
inspect
class type inspect ipsec_cmap_out (same problem with VPN when inspected)
pass log
class class-default
drop log
But unfortunately, the same problem occurs. Curiously, the first two packets seem to go "through" the firewall, but with 3rd packet the packetloss comes up:
                                                Packets               Pings
Host                                         Loss%   Snt   Last   Avg Best Wrst StDev
1. Stuttgart-I28-1.belwue.de                 50.0%     3    0.3   0.3   0.3   0.3   0.0
2. Stuttgart-AL30-1-gi0-0-0-3.belwue.net     50.0%     3    0.9   0.9   0.9   0.9   0.0
3. Karlsruhe-RZ-1-10GE-0-1-0-1.belwue.net     0.0%     2    2.7   2.7   2.7   2.7   0.0
4. Karlsruhe1-10GE-4-0-0.belwue.net           0.0%     2    1.5   1.5   1.5   1.5   0.0
5. Mannheim1-10GE-3-0-0.belwue.net            0.0%     2    2.5   2.5   2.5   2.5   0.0
6. Frankfurt-DECIX-1-10GE-0-0-0-0.belwue.net 0.0%     2    4.1   4.1   4.1   4.1   0.0
7. de-cix20.net.google.com                    0.0%     2    5.0   5.0   5.0   5.0   0.0
8. 72.14.238.44                               0.0%     2   39.2 39.2 39.2 39.2   0.0
9. 72.14.236.68                               0.0%     2    5.4   5.4   5.4   5.4   0.0
10. 209.85.254.118                             0.0%     2    5.4   5.4   5.4   5.4   0.0
11. ???
12. google-public-dns-a.google.com             0.0%     2    5.5   5.3   5.2   5.5   0.2
                                                 Packets               Pings
Host                                          Loss%   Snt   Last   Avg Best Wrst StDev
1. Stuttgart-I28-1.belwue.de                  66.7%     4    0.3   0.3   0.3   0.3   0.0
2. Stuttgart-AL30-1-gi0-0-0-3.belwue.net      66.7%     4    0.8   0.8   0.8   0.8   0.0
3. Karlsruhe-RZ-1-10GE-0-1-0-1.belwue.net     66.7%     4    2.1   2.1   2.1   2.1   0.0
4. Karlsruhe1-10GE-4-0-0.belwue.net           66.7%     4    1.5   1.5   1.5   1.5   0.0
5. Mannheim1-10GE-3-0-0.belwue.net            66.7%     4    2.6   2.6   2.6   2.6   0.0
6. Frankfurt-DECIX-1-10GE-0-0-0-0.belwue.net 66.7%     4    4.2   4.2   4.2   4.2   0.0
7. de-cix20.net.google.com                    66.7%     4    5.3   5.3   5.3   5.3   0.0
8. 72.14.238.44                               66.7%     4   70.3 70.3 70.3 70.3   0.0
9. 72.14.239.60                               66.7%     4    5.8   5.8   5.8   5.8   0.0
10. 209.85.254.116                             66.7%     4    5.8   5.8   5.8   5.8   0.0
11. ???
12. google-public-dns-a.google.com              0.0%     4    6.3   5.7   5.2   6.3   0.5
In the sessions on the routers, I see only this entry:
         Session 206F66C (129.143.6.89:8)=>(8.8.8.8:0) icmp SIS_OPEN
Any other suggestions?

Problem with zone creation in Solaris 10 6/06

Hi,
I have configured and installed a non-global zone following the example given in the guide http//www.sun.com/software/solaris/howtoguides/posgresqlhowto.jsp. My zone has the following configuration:
# zonecfg -z pg_zone
zonecfg:pg_zone> info
zonepath: /export/zones/pg_zone
autoboot: true
pool:
fs:
dir: /pg_log
special: /dev/dsk/c1d0s0
raw: /dev/rdsk/c1d0s0
type: ufs
options: []
net:
address: 192.168.10.100/24
physical: bge0
zonecfg:pg_zone> exit
The installation completed but I got the following errors:
# zoneadm -z pg_zone install
Preparing to install zone <pg_zone>.
Creating list of files to copy from the global zone.
Copying <130101> files to the zone.
Initializing zone product registry.
Determining zone package initialization order.
Preparing to initialize <1059> packages on the zone.
Initialized <1059> packages on zone.
Zone <pg_zone> is initialized.
Installation of these packages generated errors: <SUNWgnome-a11y-libs-share>
Installation of <63> packages was skipped.
The file </export/zones/pg_zone/root/var/sadm/system/logs/install_log> contains a log of the zone installation.
When examined the logs there were several messages like this:
SUNW_PKG_THISZONE=true in the pkginfo file.
*** package <SUNWamutl> was not installed:
The package <SUNWamutl> is registered to be installed in the
global zone only. The package may have been installed in the global
zone using the pkgadd '-G' option, or the package may contain a
request script, or the package may directly set the package attribute
SUNW_PKG_THISZONE=true in the pkginfo file.
*** package <SUNWiimdv> was not installed:
The package <SUNWiimdv> is either not fully installed in the
global zone, or the package contains a request script. Only packages
that are fully installed in the global zone and that do not contain a
request script can be installed when a new zone is created. If this
package does not contain a request script, you can correct this
problem by removing and reinstalling the package in the global zone.
And when I try to boot the zone I get this error:
# zoneadm -z pg_zone boot
zoneadm: zone 'pg_zone': "/usr/lib/fs/lofs/mount -o zonedevfs /export/zones/pg_zone/dev /export/zones/pg_zone/root/dev" failed with exit code 33
zoneadm: zone 'pg_zone': call to zoneadmd failed
Any suggestion how to solve this problem?
thanks

To answer your question wangzh: Yes I did. I actually followed exactly the procedure on the how-to-uides: http://www.sun.com/software/solaris/howtoguides/containersLowRes.jsp.
I think the problem here might reside in the script supplied in the solaris distribution for creating zones. For example, in the default configuration script, the package directories /lib /platform /var and /usr are by default set to be automatically imported. But when I try to create a zone using these defaults settings, it ends up with an mounting error that prevents the installation of the zone. only when I remove manually those directories from the configuration then the installation continues.
And during the installation process there are number of packages that are by default imported via the installation script and this is some of those packages that cause the errors here. I also tried to exclude the offending packages as suggested by henryC but I couldn't find all of them and the creation still fails at the booting.

D6603 Problem with sounds [alarm, spotify, calls]

Hey,
I have a several troubles with my new Z3 (D6603). All problems are related to sounds and... occur randomly.
1. Bug with spotify application (Often)
2. music plays at one time with call (occurred once)
3. I shut off alarm by swipe off and ring still playing (occurred once)
Ok, well...
1.Spotify player *if it helps, i have logs*
I have a trouble with playing in the background when screen is locked
Device: Sony Z3 / 4.4.4
Common problems:
1) Music plays only for ~15 / 20 sec when screen is locked
2) in application play/pause, fwd, backward buttons are clickable but don't respond
3) In lock screen i don't have spotify widget when problem occurs
4) In notification bar i don't have spotify widget when problem occurs
Clearly there is a problem between the lockscreen/notification bar and spotify...When tapping a play button, app doesn't respond. The problem resolves itself after a long moment but not always.
steps to produce the error:
1. Open Spotify (Premium sub)
2. Tap play button
3. Tap lockscreen button (screen is turn off)
4. Tap lockscreen button again (screen is switched on lock screen view where we have Spotify widget)
5. Music plays for about ~15/20 sec. and at the same time i can shut off application where in spite of everything music plays for that 20 sec. Of course application didn't respond to clicking navigation button like play/pause...
clearing cache, reboot, clean reinstall application and restoring to factory settings don't help..
2. Music and calls
I listened to music on spotify when my friend called. I received a call and music... didn't stop. I listened to my friend and music at the same time... I couldn't stop the music in any way...
3. Alarm
I set the timer for 20 minutes, after 20 minutes I turned off alarm by swipe action and ring still played... just reboot the device helped.
What i should do with that problems?
PS
i have a operator branded device [T-Mobile PL] ...

Then the problem will be with spotify, it will be wise to contact the app developer.
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Problem with zone installation on solaris 08/07

Hello :)
I need some help
I install solaris 10 08/07 on my x2100 M2.Everything is ok.
Then I try to install non-global zone named web-zone with the following commands:
# mkdir /export/web-zone
# chmod 700 /export/web-zone
# zonecfg -z web-zone
web-zone: No such zone configured
Use 'create' to begin configuring a new zone.
zonecfg:web-zone> create
zonecfg:web-zone> set autoboot=true
zonecfg:web-zone> set zonepath=/export/web-zone
zonecfg:web-zone> add net
zonecfg:web-zone:net> set address=192.168.0.3
zonecfg:web-zone:net> set physical=bge1
zonecfg:web-zone:net> end
zonecfg:web-zone> info
zonepath: /export/web-zone
autoboot: true
pool:
inherit-pkg-dir:
dir: /lib
inherit-pkg-dir:
dir: /platform
inherit-pkg-dir:
dir: /sbin
inherit-pkg-dir:
dir: /usr
net:
address: 192.168.0.3
physical: bge1
zonecfg:web-zone> verify
zonecfg:web-zone> commit
zonecfg:web-zone> exit
# zoneadm -z web-zone verify
# zoneadm -z web-zone install
# zoneadm list -cv
# zoneadm -z web-zone boot
When I zlogin into zone configuration stack with:
Fatal internal error: prompt_error called before prompt_open!
The IP address previously set on the network interface
is no longer available. The system state is corrupted. System identification
can no longer continue.
Press Return to continue
And that�s it :)
On interface bge1 I have 2 ip addresses, one for management processor (192.168.0.254) and one for global zone (192.168.0.2)
The output from ifconfig �a is :
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
lo0:1: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
zone web-zone
inet 127.0.0.1 netmask ff000000
bge1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.0.2 netmask ffffff00 broadcast 192.168.0.255
ether 0:1b:24:5:4f:6f
bge1:1: flags=4001000842<BROADCAST,RUNNING,MULTICAST,IPv4,DUPLICATE> mtu 1500 index 2
zone web-zone
inet 192.168.0.3 netmask ffffff00 broadcast 192.168.0.255
Any Ideas ?? :)
Thaks
pp Sory for my baad english :)

Hi
Thank you for replay
This is happened exactly when I zlogin for first time to complete installation.
The installation procedure flow flawless.I set terminal type 13 (dt terminal) and everything is OK, but when I try to setup hostname I�ve got this error.
I try this with 3 different zones on this machine with same result
I have old x86 machines with solaris 11/06 zones installed , everything works fine (1 year uptime)
This is not the first zone in my life :)
Best Regards
DJ JAM

Problems with zone CREATE commando

root@stjsc1p# zonecfg -z myzone
error: failed to load external entity "/etc/zones/myzone.xml"
myzone: No such zone configured
Use 'create' to begin configuring a new zone.
zonecfg:myzone> create
ld.so.1: zonecfg: fatal: relocation error: file /usr/lib/libzonecfg.so.1: symbol xmlNewValidCtxt: referenced symbol not found
Killed
Whats my problem?
regards

SSH:root@stjsc1p# ldd /usr/lib/libzonecfg.so.1
libc.so.1 => /usr/lib/libc.so.1
libxml2.so.2 => /usr/lib/libxml2.so.2
libxml2.so.2 (SUNW_1.3) => (version not found)
libpthread.so.1 => /usr/lib/libpthread.so.1
libz.so.1 => /usr/lib/libz.so.1
libm.so.1 => /usr/lib/libm.so.1
libsocket.so.1 => /usr/lib/libsocket.so.1
libnsl.so.1 => /usr/lib/libnsl.so.1
libmp.so.2 => /usr/lib/libmp.so.2
libmd5.so.1 => /usr/lib/libmd5.so.1
libm.so.2 => /usr/lib/libm.so.2
/platform/SUNW,UltraAX-i2/lib/libc_psr.so.1
/platform/SUNW,UltraAX-i2/lib/libmd5_psr.so.1
SSH:root@stjsc1p#

Question re Zone Alarm and WRT54G admin page display problem

First - thanks to all who posted about Zone Alarm - I was going to exchange my router this weekend - I spent an hour on the phone with tech support and she was trying to get my router updated with v9 through a roundabout way, but I kept getting an error that said my Flash could not be erased - so she thought the firware on my router was somehow corrupted. But I'm definitely going to check out the Zone Alarm idea first.
My question is - can someone tell me exactly how to disable Zone Alarm? I thought I had done so, but I guess not - I'm not very familiar with Zone Alarm. Also - I had purchased Zone Alarm about a year ago, (was using it with a Linksys wired router) and suddenly I am getting messages on restart telling me my "trial period is up" - of course I can't find my original packaging to enter a serial number (altho one is already entered and they say it's not *valid*) so I have to select an option that tells me I am no longer protected. (unless I pay another $40 to re-register it!!) Could this be part of the problem?
Final question - sorry for being such a newbie - but do I really need both Zone Alarm and the firewall in the router? ZA says it has caught thousands of attempts on my system - while it was running with my non-wireless router installed - is that a crock? Or is actually good to have both software and hardware routers? And if I do need ZA still - does it have to be disabled everytime I want to access the admin page? Then turned back on?
ugh!
thanks -
Mary

LOL - This forum is great, I've been here 5 minutes and now have some fresh perspectives on a couple of problems.
I would NOT recommend paying for ZA. What the heck were they thinking when they created their 'Zones'? They should have named it something else for one, like 'Complicated rules and policies that are guaranteed to hack up everything you try to do (and it gets even worse when you restore the settings you tweaked back to their defaults)' But I guess that's a little too long.
Marynospam: Your Windows firewall (if ur on windows) will do a pretty good job of keeping out unwanted visitors from the Internet. It will NOT stop malware from calling out! Modern day scumbags slip you a trojan that will spy, record, copy, and call them back with whatever they want from you. If you are using Microsoft Windows DO NOT TURN OFF your 3rd party firewall! Of the firewall/security vendors I have experience with, McAfee is the best. I have only used their firewall and viruscan, and don't have experience with their 'spyware' package.

Problems with alarm

Hi,
Have had a problem with the alarm on my iPhone since I updated my 3GS to IOS4. The problem is I had about 10 recurring alarms before I updated that have literally multiplied by thousands now. There are so many i cannot even get into the alarm part of the clock app with out it crashing. This is very annoying because so many go off at once that it causes the iPhone to crash because of RAM shortage and this happens every day, a solid hour of my iPhone going crazy between the hours of 7am to 8 am. Worse still when i upgraded to the iPhone 4 the bug came with it!
Would anyone have any idea how to fix this? I keep praying for a patch!
Thanks

Thanks!!! Worked a charm!
I tried restoring before but never as a new phone!
Cheers man!! Much appreciated!

Zone Alarm Issues

+This isn't really a question, more of a suggestion.+
As of today (11-12-09) Apple hasn't solved this issue that deals with Zone Alarm software. Maybe in the near future they will, but who knows. Anyways, I'll start with the problem:
A month or so ago I had the dreaded RESTORE LOOP problems when I updated my iPhone to v3.0. After many days and hours of attempting to resolve the issue I figured my phone was fried and no longer usable. I took it to the Apple store and told them of the issues and they gave me a brand new one, no questions asked. Thanks Apple! The new phone had v3.1 installed on it so I figured the problems with updating were over, WRONG. I took it home and a week later they released an even newer version of the software along with the AT&T carrier settings update. Before updating I synced some songs, music videos, and tv shows. When I tried to play the songs back every one had a really high pitched squeal or would stop playing halfway through. The videos were all choppy and had little green boxes scattered across the screen every few seconds. I erased everything and updated the phone and iTunes to the newest version hoping to solve the problems. Nope, but I did eventually find a solution over the next day or so.
Problems:
1. Phone stuck in RESTORE LOOP when trying to update to any version.
2. Music is choppy and sounds like a dial up modem.
3. Videos are unwatchable due to small green boxes all over the screen.
Solution:
1. SHUT DOWN ANY ZONE ALARM PRODUCTS RUNNING ON YOUR COMPUTER BEFORE RUNNING iTunes.
I consider my knowledge of computers and software to be above average and in no way claim to know everything. This solution to a seemingly stupid problem was stumbled upon by the old "trial and error" method. Please respond to this post if you know the technical reason why this problem occurred.
Best of luck, and I hope this solution helps others out there work around this issue until Apple fixes it (hopefully soon).
+*Zone Alarm Security Suite v8.0.400.020*+
+*iTunes v9.0.2.25*+

I did contact Zone Alarm via email, but as of today they have not yet responded with any answer.
This is an issue that both Apple and Zone Alarm need to address, not just Zone Alarm. I posted this in the Apple forums because the problem did not exist before the iPhone v3.0 firmware and iTunes (I don't remember what version) updates. If you roll your phone firmware and iTunes software back to a previous version this problem does not exist. In a perfect world all software would learn to get along with each other.
I have not updated my Zone Alarm software in the last 5 months, and have not made any firewall changes either. So, obviously the changes made by Apple were the ones causing the problems.

I have to turn off ZOne ALarm web security for Firefox to open properly

I have Firefox 5.0 and Zone Alarm Extreme Security (10.0.246.000). When I open Firefox I get the welcome screen, as if I have just downloaded Firefox (no home page and no bookmarks - options are set at default). So, I close the browser and disable Zone Alarm Web Security and reopen Firefox. My home page and bookmarks load properly, options as previously set. I turn on ZA Web Security and all is fine until I close Firefox - then I have to do this all over again.

P.S. This copy of a post by BadK_FFox (from last week) may also help:
https://support.mozilla.com/en-US/questions/840168<br>
Firefox 5 will not start with Zone Alarm Ver 10.0.240.000<br>
'''Quote:'''
I'm running Win7 x64 with ZoneAlarm Extreme Security 10.0.241.000
I had the same problem with Firefox 4. After turning off ForceField Toolbar, it started working fine.
Then I updated to Firefox 5 and it wouldn't start, instead it was showing an error message from ZA...
I searched mozilla support and followed the instructions here: http://kb.mozillazine.org/Browser_will_not_start_up on the topic"Firefox does not start after updating with ZoneAlarm ForceField enabled".
The correct instructions for this ZA version should be: "Internet -> Web Security -> Settings, and click Clear Virtual Data"
After that I could open Firefox again! Then I realized it was still version 4... I installed the update, and everything went smooth. Checked again if Forcefield toolbar was inactive (it was) and opened a few pages, closed Firefox and opened again. After a while it wouldn't open...
AGAIN the "Clear Virtual Data" did the trick...
This time I clicked on Settings (next to "Clear Virtual Data") -> Advanced Settings, and turned off "Enable Virtualization".
Until ZA get a fix for this, either we turn it off or clear virtual data every few moves...

Reader 9.3 and Zone Alarm conflict

I am having serious computer crash problems when Zone Alarm asks about allowing Reader 9.3 access to the internet. This happens when I boot up.
I tried msconfg to stop the reader sl from loading at start up but this was no help. In the meantime have done an un-install and am running Fox-it.
OS is Windows XP pro. Any help would be great.

I gave up with Zone Alarm a few years ago. It was causing way to many problems for Apps I was running. There are less problem-some security apps.

Download Error with Free Trail Zone Alarm

Attempted to download a free trail of Zone Alarm to my Toshiba Satellite A505-S6960. The download went through its normal process of scanning and found no viruses. On completion of the download it showed I was fully protected. However, on restart of my computer through Internet Explorer the message read "THEIR MIGHT BE A PROBLEM WITH ONE OR MORE NETWORK ADAPTERS ON THIS COMPUTER." Can anyone tell me what this means? I tried diagnosing the problem through Windows and they stated I could reset the adapters through the IP. Right now the only way I can access the internet was to uninstall the Zone Alarm program. Other than Windows Defender I'm unprotected. There seems to be a viable Anti Virus program through Microsoft Essentials. As recommended by the forum I may take this route. Any further suggestions or help would be greatly appreciated.

Please try removing Acrobat completely using cleaner tool and then try re-installing it.
http://labs.adobe.com/downloads/acrobatcleaner.html
Regards,
Anoop

Problem with Path Managed property in alternate zones - also we have identified problem with Product catalog in alt zones

Hi All,
I'll start "one step back". Note we have resolved this issue but it is worth mentioning:
Yesterday we set up the product catalog. We were having a lot of inexplicable problems with it initially. After much troubleshooting, we found that it was because we were browsing the SharePoint site via the "Internet Zone" rather than the "Default
Zone" when we "Connected" our site to the product catalog. Issues experienced:
1) "Catalog Item URL Format" displayed error "Properties <Managed Property> specified by the shared catalog could not be found in the search schema" when attempting to connect to the catalog, despite that managed property being
configured correctly. The catalog would connect despite the error, and the navigation worked fine.
2) The search Result Source for the catalog would not return any results. Configuring the query and selecting "Advanced Mode" would show SPSiteURL:http://externalURL.domain.com. Changing SPSiteURL manually to
http://InternalURL resulted in results being returned as expected.
After much troubleshooting, we found that if were browsing SharePoint using the default zone (http://InternalURL) when we connected the Product Catalog, the result source then worked properly (internally and externally).
Ok, so now onto our current problem:
The Product Catalog appeared to be working properly (internally and externally) after figuring out that we needed to connect it from the Default Zone. However, we have found a remaining glitch, which doesn't appear to be Product-Catalog-specific. Consider
the following scenario:
1) We click a category in our Product Catalog, such as Electronics
2) A list of our electronic devices are presented via the "Category" display page
3) If we click on a specific item, a different URL is returned internally vs externally. We only get the friendly managed navigation URL when browsing via the Default zone. And of course totally different pages load based on which URL you get.
Internal (when browsing via Default zone):
http://InternalURL/catalog/PRODUCT-CATEGORY/PRODUCT-NAME
External (when browsing via Internet zone):
http://ExternalURL.domain.com/catalog/Lists/Products/DispForm.aspx?ID=1
We have reviewed the display template, and the "Path" managed property is simply being used to render the link. Furthermore, we have configured the Content Search web part's "Property Mappings" to show the "Path" MP, and it
displays the same (wrong) result externally.
This tells us that the Path MP is not correctly rendering "Friendly URLs" when using managed navigation.
Any help/ideas?
Our environment:
SharePoint Version: 15.0.4667.1000
Default Zone: http://InternalURL
Internet Zone: http://ExternalURL.domain.com
We are NOT using host named site collections
We ARE crawling the Default zone URL in our content source
Thanks,
Tommy

Hi,
We have now also observed the same issue with a Managed Property of type “Hyperlink/Picture”. The picture returns the wrong URL externally.
This post describes the same issue, however the poster found that setting UseAAMMapping=True doesn’t work in 2013:
http://sharepoint.stackexchange.com/questions/104806/set-the-useaammapping-property-of-a-managedproperty-object-map-an-url-of-a-h
We checked, and our Picture MP had UseAAMMapping=False. We set it to True, did a full crawl, and see no change in behavior. Path already had UseAAMMapping=True.
More info:
http://macslui.blogspot.com/2013/02/sharepoint-2010-problem-in-image-result.html
https://camerondwyer.wordpress.com/2014/08/04/beware-sharepoint-2013-search-results-and-the-listurl-property/#comment-2606
Thanks,
Tommy

Problem with zone alarm.

Similar Messages

Maybe you are looking for