Problema instalar LabView

estoy tratando de instalar LabView en mi laptop Lenovo de 2 Gb de RAM, con bastante espacio y al correr el setup de cualquier versión ya sea 7.1,8.6,9,12 me dice, mientras lo hago que debo instalar LabView versión tal le doi aceptar y me dice que no se instaló correctamente que si quiero seguir instalando el resto y finalmente no se instala. En mi casa en una Pentium 4 con Windows XP si se instaló perfectamente

Hola
Tienes razón, todas las que he tratado de instalar son desde  DVDs y  lo 1ero que hago es tratar de instalar LabView, he limpiado registro luego de cada instalación fallida y los he desinstalado, pero el proceso es tan rápido (instalación), que es como si no se hubiera instalado y cuando lo chequeo, así es, solo aparece la carpeta NI en C, y otras que debo eliminar a veces a mano. Y de los toolkits, lo que te envié.
Saludos, Ayvlis.
RichieTheBard wrote:
Me gustaría aclarar un par de cosas más. Por lo que veo me parece que estas utilizando un DVD para la instalación de LabVIEW, ¿es este el caso para todas las versiones de LabVIEW que has intentado instalar?
Según entiendo este problema te aparece con todas las versiones de LabVIEW, cuando intentas instalar cualquier toolkit, o módulo. Sin embargo me gustaría saber si se logra completar el proceso de instalación de LabVIEW como tal, y si has intentado instalar LabVIEW primero y posteriormente instalar únicamente los toolkits y módulos que necesites.

Similar Messages

  • Run-time engine problem in Labview 2009 and Labview 2010

    I have a problem with Labview 2009 and Labview 2010. I updated my Labview 2009 into 2010. But it turned out to be a trial one, because i did not have the serial number. So I uninstalled the Labview 2010. however, the funny stuff came over. I cannot use my Labview 2009. So i uninstalled Labview 2009 again. But eventually, I could not reinstall Labview 2009. Every time i had a runtime error and i could not proceed with the installation. in addition, any installation  related to Labview is not permitted and the same error came up every time. it is very annoying.
    So, What is the deal?
    I attached the error here. Any comments or advice are welcomed and appreciated.
    Attachments:
    error.docx ‏2305 KB

    By chance is this machine's language set to any non-English locale?  You would check the locale setting by:
    Opening Control Panel.
    Opening "Regional and Language Options".
    Looking Under "Regional Options" >> "Standards and Formats"
    If it is set to something besides English, trying setting it to English and please report back what locale it was set to (or if this even solves the problem).
    Regards,
    - WesW

  • Distribution problem in labview 2011(Error 11004)

    Hi,everyone. I have a problem when i install my build "install". If i include "NI Labview Run-Time Engine 2011" in additional installers, the build files show the error message"
    .\Distribution.cpp(2072): InstallerError 11004
    Developer Error. Distribution contains invalid dependencies:
    1. Product SN1Debug ({4CC67F54-9DD9-4DF2-B9C4-1158C9E9F412}) depends on
    product with upgrade code {6AD6C111-233B-4924-A3BF-E4813FE23C7A},
    version [11.0.416.0,), language in {}
    which is not in the distribution.
    Correct the distribution and try again.
    <No Debug Message>
    "  when i install it. and if i don't include it, the install is OK.
    I want my distribution include lv2011 run-time engine, how can i do to deal with this problem?
    Labview 7.0, 8.0, 8.6,8.6.1,2011
    Attachments:
    11.png ‏20 KB

    Hi,
    please try to download and install the NI Labview Run-Time Engine 2011 on your computer and run the builder again.
    http://joule.ni.com/nidu/cds/view/p/id/2534/lang/en
    In this folder are the installer saved:
    C:\Programme\National Instruments\Shared\ProductCache
    Regards,
    Michael

  • Problems Installing LabVIEW

    Problems Installing LabVIEW Run-Time Engine for Ubuntu 11.04
    I'm relatively new to Ubuntu and its community, but have been pleasantly surprised with how easy troubleshooting has been. Unfortunately, I've spent the last two days trying to install the LabVIEW Run-Time Engine, but keep coming up short.
    I've tried a number methods from the following threads to no avail:
    The problem I'm having now is that despite having the ia32-libs, here is what comes up:
    Input: "sudo alien - k --scripts labview-2009-rte-9.0.1-1.i386.rpm"
    Response: "labview-2009-rte-9.0.1-1.i386.rpm is for architecture i386; the package cannot be built on this system".
    Alien is required because Ubuntu isn't compatible with the .rpm format.
    Your help would be immensely appreciated since we use LabVIEW programs to display, manipulate and simulate our spectra.
    SZD91
    Argumentative Essay

    Hey there I'm not too familiar with Ubuntu but you may find some help in the following areas:  Linux Users is a group that helps out other linux users.   Also  labview for linux (Ubuntu 64-bit) my help, people were having a pretty active discussion in there.
    I'm guessing you're using the installer from here: LabVIEW Run-Time Engine 2011 -Linux?
    Scott A
    SSP Product Manager
    National Instruments

  • Dear frnz, i am doing my prjct in Lview. ie online PQ monitoring​. i need to simulate the system with disturbanc​es generated in Lview. so can any bdy plz tel me how to genrte PQ problems in labview. thanks in advance..

    dear frnz, i am doing my prjct in Lview. ie online PQ monitoring. i need to simulate the system with disturbances generated in Lview. so can any bdy plz tel me how to genrte PQ problems in labview. thanks in advance..

    I work in the power conversion industry and do these types of measurements all the time…
    Do you want to just measure power quality or create and measure power quality problems?
    What hardware are you using?
    Power quality analyzer?
    Programmable AC power source?
    Fast Transient Generator?
    Here is an example of what I do.
    To create PQ problems I use a California Instruments AC source set to nominal power for the unit under test. Using Labview I program several transients consisting of fixed and random duration dropouts and surges. I also use a Schaffer Fast Transient Burst Generator to apply high frequency noise bursts directly onto power lines.
    For measuring power quality I use a Voltech PM3000A power analyzer and Labview to measure everything from voltage, current, and frequency, to  harmonics and %THD
    Message Edited by RTSLVU on 07-23-2008 10:31 AM

  • Problems with LabVIEW 7.1 and lock-in amplifier Stanford SR530?

    Does has anybody had problems with LabVIEW 7.1 and the instrument driver for the lock-in amplifier Stanford SR530?
    With LabVIEW 6 there are no problems at all, but with LabVIEW 7.1 it is impossible to communicate with the instrument.

    amr_attia wrote: (Private message, no need to private message)
     My problem is to get the data out from the divice x and y readings . Can you help me
    Here is the code and snippet. I had it from before. It reads Channel 1 and Channel 2 from the SR530, that is whatever the display is for Channel 1 & 2. You set the display manually or programmatically, I let you figure that part out.
    Cheers,
    mcduff

  • Como instalar Labview 2013 SP1 si tengo instalado Labview 2013

    Buenos Días,
    tengo Instalado Labview 2013 y quisiera saber si tengo que desinstalarlo para instalar labview 2013 SP1
    Espero sus respuestas
    Gracias!
    Solved!
    Go to Solution.

    * Yo no hablo español. He utilizado Google Traductor. 
    No. Usted debe ser capaz de instalar LabVIEW 2013 SP1 en la parte superior de la original de LabVIEW 2013. No debería haber necesidad de desinstalar. Sólo asegúrese de que usted tiene el Programa de Servicio Estándar (SSP). LabVIEW 2013 Service Pack 1 es una actualización exclusiva para LabVIEW 2013 para el Programa de Servicio Estándar (SSP) a los clientes.
    descargar
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    *I do not speak Spanish.  I used Google Translator.
    No.  You should be able to install LabVIEW 2013 SP1 on top of the original LabVIEW 2013.  There should not be a need to uninstall.  Just make sure you have NI Standard Service Program (SSP).  LabVIEW 2013 Service Pack 1 is an exclusive update to LabVIEW 2013 for NI Standard Service Program (SSP) customers.
    Download
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    If someone helped you out, please select their post as the solution and/or give them Kudos!

  • Strange math-problem with LabVIEW 7.1

    Hello!
    I am using LabVIEW 7.1 and I came to this strange math-problem. Could it be that it is a problem of LabVIEW 7.1?
    Ok try this with LabVIEW 7.1:
    open a new VI
    place a subtract-VI (pallet numerical) on the block diagram and try to subtract 0.2 from 1.6
    place a less-VI (pallet compare) on the block diagram and wire a numerical constant 1.4 to input x
    wire the result of the subtraction to input y of the comparison
    place an LED to the output of the comparison
    and start this.
    What does it say?
    The LED should turn on and this means here that 1.4 would be less than 1.4 .
    But I would have expected that 1.4 is not less than 1.4 .
    This works also if you add or subtract upto 0.2 to/from the values 1.4 and 1.6 (or equivalent with 0.2) .
    If you change the inputs of the comparison then the result is as expected and 1.4 is reported not to be less than 1.4 .
    If you compare two constants with the same value 1.4 you will not get the same strange result.
    Does anybody have an explanation for this?
    Espelkamper

    Hello,
    For floating point math: Rounding to multiples of 0.1 is problematic as
    those numbers are infinite fractions in base2 representation...
    So maybe you should change your numbers to integers using fixed point math. If all your input values are in the range of 1.4 to 1.8 you can multiply by 10000 and round to next integer. Then do your comparison on that integer (there's also an 'InRange' function in the comparison palette).
    Best regards,
    GerdW
    CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
    Kudos are welcome

  • Will there be problems installing LabVIEW 7.1 if I upgrade to Windows XP?

    We have a program in LabVIEW 7.1 running on Windows 2000.  We plan to upgrade all of our computers to Windows XP.  Will there be any problems installing LabVIEW 7.1 onto Windows XP?

    Hi,
    No, you won't experience any problems with that upgrade.  LabVIEW 7.1 is fully compatible on Windows XP, just as it is on Windows 2000.
    Peter
    Peter L.
    Applications Engineer
    National Instruments
    www.ni.com/support/

  • Problem on LabVIEW + Debian 64bits

    Hello,
    I'm trying to install LabVIEW 7.1 on my Debian SID x64, I have all de requirement writen in the Readme.txt and I tryed to install it by INSTALL-norpm . The problem is that I always get :
    #sh INSTALL.norpm labview70-appbuild /usr/local/share/labVIEW/
    Installing labview70-appbuild-7.0-1.i386.rpm into /usr/local/share/labVIEW/...
    /home/esox/labview/rpm2cpio: error while loading shared libraries: libdb.so.2: cannot open shared object file: No such file or directory
    even if :
    #locate libdb.so.2
    /lib/libdb.so.2
    Could you help me?
    Thanks a lot

    it seems to be very very hard to install Oracle 9i on Debian Etch, I found this on the net :
    > Is it possible to install Oracle 9i on Debian etch?
    So far I have had no luck due libraries requirement.
    I appreciate any suggestions.Officially no.
    Unofficially, you should be able to with a loooot of tweaking. The
    secret is in the "compat" libraries. Basically Oracle is a binary
    distribution and relies on gcc296 - not gcc3. You should also get your
    own jdk install. Get 1.1.8 (yep - good old one) and use it to run the
    installer. With Oracle9i there's no gurantee that the jdk in the
    installer will run on your distro. Luckily you can override the jdk with
    your own.
    If anyone knows a simple way to do it, I'd like to know, but I'd rather give up about this idea
    It seems to be to tricky for my poor Linux knowledge

  • Problem with Labview and an ARM Cortex

    Good morning,
    I am currently trying to use Labview with a board from ST Microelectronics (MCBSTM32) with an ARM Cortex Processor.
    I use the SDK and have followed the tutorials.
    But, when I try to launch the program (the simple loop as write in the tutorial n°2 : http://zone.ni.com/devzone/cda/tut/p/id/7029 ), Keil gives me an error via Labview:
    "Argument 'DARMSTM' not permitted for option 'device'."
    It seems that Keil does not allow an ARM Cortex from ST as the device.
    Moreover, after having this problem, I am unable to use a Keil project ,even a project which worked before, without Labview. I need to restart the computer.
    I also try to launch the Keil project generated by Labview, without using Labview, and it works. But as soon as I use Labview, I have the error.
    Did anyone already have this error or know how to solve it
    Thank you for your answer and sorry for my bad english.
    Regards,
    Raphaël VAISSIERE

    Hi Raphi,
    So let me make sure I understand,
    The project created in LabVIEW errors out with the message "Argument 'DARMSTM' not permitted for option 'device" 
    If you open the same project in Keil uVision, it runs fine
    Here are my questions:
    1. So how does the code run when run through Keil? does it deploy and run fine?
    2. Did you follow the porting procedure completely?
    Your target STM32F103RB  is techincally supported by Keil but you need to port the RTX kernel to it. This paragraph explains it:
    To determine if your target already supports the RTX Real-Time Kernel, browse to the \Keil\ARM\Startup directory, then browse to the folder that corresponds to the manufacturer of your ARM microcontroller. If there is an RTX_Conf*.c file for your target, then the RTX Real-Time Kernel has already been ported for your ARM device. If no such file exists, skip to chapter 4 for more information on the RTX Real-Time Kernel and a guide for porting RTX to your ARM microcontroller. 
    You also need to port the Real-Time agent to it.
    I just want to make sure that you have followed the guidelines. If you have and are still having problems, we will continue to explore this.
    Thanks,
    National Instruments
    LabVIEW Embedded Product Support Engineer

  • Problems with Labview and Windows XP with error -214721786​5

    Hello. Im a new beginner in Labview and am having a problem with a error message
    I dont understand. Im running Labview on a pc-logger with windows XP.
    The program is written by a guy on my university, and logs voltage from
    a solar cell panel. He doesnt have the time to check in to it, so Im supposed to
    find out what's wrong.
    The error message is as follows :
    Error -2147217865 occured at Cmd Execute.vi->DB Tools Insert
    Data.vi->Solcelle.vi
    Possible reasons :
    Exception occured in Microsoft OLE DB Provider for ODBC Drivers,
    [MySQL][ODBC 3.51 Driver][mysqld-3.23.38-log]Can't open file :
    'solcelledata.MYD'. (errno: 145). in Rec Create - Command.vi-
    >Cmd Execute.vi->DB Tools Insert Data.vi->Solcelle.vi
    I really hope someone can tell me what's wrong and specifically what to do
    with it, or possibly guide me to someone who could suggest a solution to this
    problem.
    Reguards
    chrisdee

    Hi Chrisdee,
          (.. not to discount what TimoS has suggested, however...) 
    Embedded in the error information you provided:
    ... Can't open file : 'solcelledata.MYD'.
    Sounds like the program needs this file?  Has the program been moved to a new location?
    just a wild guess!
    Cheers
    Message Edited by Dynamik on 10-06-2005 04:53 AM
    When they give imbeciles handicap-parking, I won't have so far to walk!

  • XY Graph Cursor Problem in Labview 7.1.1?

    Hallo,
    I am  using Labview 7.1.1 and I am facing one problem with XY graph cursor. If I am moving cursor in one graph, I am expecting same movement in another Graph. But when I move cursor in Graph1, cursor in second graph moves but not to exact X value of Graph1.
    Property of Cursor in both graphs must be "Lock to Plot"
    If any body knows about this please let me know ASAP. I am attaching example VI for your reference.
    Thanks,
    Sashi
    Attachments:
    XY Graph Cursor Problem.vi ‏101 KB

    It's a curious effect. Probably the floating point coordinate is sensitive to the exact pixel alignment (I mean that this would not happen if we had for example 1 pixel per point in the X direction).
    Anyway, if you use Cursor Index instead (which is an integer) the behaviour is as expected.
    Paolo
    Paolo
    LV 7.0, 7.1, 8.0.1, 2011

  • Problems calling LabVIEW VI through ActiveX inside another LabVIEW VI

    Hi everybody,
    basically I would like to create an ActiveX to be inserted in a LabVIEW VI which at its turn would call another LabVIEW VI.
    I have choosen Visual Basic to create this ActiveX, being the main section code:
    Dim lv As LabVIEW.Application
    Dim vi As LabVIEW.VirtualInstrument
    Dim names(0 To 1) As String, values(0 To 1) As Variant
    'Assign an object reference to VI
    Set lv = New LabVIEW.Application
    'Assign an object reference to VI
    Set vi = lv.GetVIReference(lv.ApplicationDirectory & "\Examples\General\Strings.llb\Parse Arithmetic Expression.vi")
    vi.ShowFPOnCall = False 'Open front panel if requested
    'Initialize the variables & define the strings corresponding to the VI connector labels.
    names(0) = "Arithmetic Expression": values(0) = "1+1"
    names(1) = "Result"
    'Call the VI
    vi.Call names, values
    So, when this ActiveX executes this code sequence it locks when creating the "LabVIEW. Application" object. I have tested this ActiveX from another client application (Internet Explorer) and it works perfectly, so the problem is located in the creation of ActiveX from LabVIEW. Do I need to do anything special in my code or simple it cannot be done what I want to do?
    Thanks !!!
    Jesus Valero
    Plataforma Solar de Almeria.

    Exactly, but really the code of above it's only an example that I want to do. I'm trying something more sophisticated.
    I want to create an ActiveX control that could work as stand alone executation with the ability of directly get some indicator values from its LabVIEW VI container and depending of those values, set the control values of others LABVIEW VIs. I really know that within LabVIEW itself I can get/set those indicators/controls, but with this method I think that the diagram block of the LabVIEW VI container can be more simple.

  • Is there any problems using LabView 5.1.1 on Win2K?

    I am currently upgrading the company's system from Win NT 4.0 to Win2K and I am wondering if there is any problems in upgrading LabView to Windows 2000?

    No infact i'm running LV5.1.1 and LabVIEW 6.0.2 on the Win2k system.
    A Rafiq
    National Instruments
    http://www.ni.com/support

Maybe you are looking for