Problemas conexion 3g

Tengo una Tablet thinkpad 2. Al poner el ordenador en suspensión, con frecuencia me encuentro al volverlo a encender que la conexión 3G se ha perdido. No solo eso, sino que aparece como conectado, pero en realidad no lo está. Si desconecto el 3G y lo vuelvo a conectar me indica que está conectado sin pedirme el PIN, pero no es cierto. La única manera de recuperar la conexión es reiniciar el ordenador. Lo peor es que con frecuencia el 3G desaparece del menú de redes. Me instalé el Lenovo Solución Center y, cuando pasa eso, me indica que no se pudo iniciar el módulo 3G (error 10). Únicamente vuelve a funcionar reiniciando el PC.

Pues parece que no trea WWAN...
La imagen que has posteado anteriormente no muestra tarjeta WWAN, luego he ido a la pagina de Lenovo y con el nro de serie (que he borrado de tu post) y el tipo de modelo me da esta lista de partes:
Como puedes ver en la ultima linea, solo menciona WLAN pero no WWAN, luego he visto la lista de componentes de Lenovo, la parte de tarjetas de red muestra esto:
Las opciones marcadas en amarillo serian las que tendria que tener tu T440s
La ultima opcion seria abrir la tapa y fijarse si esta la tarjeta ahi, pero estando el equipo en garantia yo lo hablaria con Lenovo o la empresa que te lo vendio para que aclaren la situacion.
En la documentacion de la notebook no menciona nada? A veces hay tarjetas WWAN que vienen bloqueadas por Vodafone o quien sea y solo la puedes usar con el software que proveen ellos. No hay ningun sticker en ningun lado?
/L40SX/240/240X/2*340CSE/360PE/365XD/380D/380E/380XD/380Z/390/560E/560X/2*570/2*600/600E/750Cs/755C/760CD/760EL/760XD/770E/A20p/A22p
A31/i1600/G40/R50p/R61i/S30/SL510/2*T22/4*T4x/11*T6x/6*T4x0x/6*T5x0/3*W5x0/W700/3*X2x/4*X3x/3*X4x/5*X6x/3*X6xT/10*X2xx/2*X200T/4*X30x/Z60m/3*Z61x
Comunidad en Español English Community Deutsche Community Русскоязычное Сообщество

Similar Messages

Problema conexion Iphone - Lg Cm2520

Compre un Equipo de sonido Lg Cm2520, al conectar el Iphone, arroja un mensaje de error. Esto no pasa con otros equipos Iphone, y por otro lado, mi equipo Iphone si funciona con otros equipos.
Atte. Sergio Zurita
97359280

De la misma forma instale el IOs8 en mi Iphone5, y tengo problemas de conectividad tanto a la red de mi operador como al Wifi, asi mismo presenta lentitud al momento de entrar a una aplicacion o tan solo en codigar el codigo de desbloqueo, esto no sucedia con la version anterior la 7. UNA SOLUCION PORFAVOR!!

Problemas conexion 3G T440s

Buenas Tardes.
Tengo un lenovo T440s con ranura para tarjeta 3G. He introducido una tarjeta, y no hay forma de que se conecte, o que me la gestione. Me podriais ayudar y decirme que programa o driver necesito, Tengo instalado "Acces Conections" pero no hay forma de que me deje gestionar la SIM.
Muchas gracias
Un saludo
Pablo
¡Resuelto!
Ir a solución.

Pues parece que no trea WWAN...
La imagen que has posteado anteriormente no muestra tarjeta WWAN, luego he ido a la pagina de Lenovo y con el nro de serie (que he borrado de tu post) y el tipo de modelo me da esta lista de partes:
Como puedes ver en la ultima linea, solo menciona WLAN pero no WWAN, luego he visto la lista de componentes de Lenovo, la parte de tarjetas de red muestra esto:
Las opciones marcadas en amarillo serian las que tendria que tener tu T440s
La ultima opcion seria abrir la tapa y fijarse si esta la tarjeta ahi, pero estando el equipo en garantia yo lo hablaria con Lenovo o la empresa que te lo vendio para que aclaren la situacion.
En la documentacion de la notebook no menciona nada? A veces hay tarjetas WWAN que vienen bloqueadas por Vodafone o quien sea y solo la puedes usar con el software que proveen ellos. No hay ningun sticker en ningun lado?
/L40SX/240/240X/2*340CSE/360PE/365XD/380D/380E/380XD/380Z/390/560E/560X/2*570/2*600/600E/750Cs/755C/760CD/760EL/760XD/770E/A20p/A22p
A31/i1600/G40/R50p/R61i/S30/SL510/2*T22/4*T4x/11*T6x/6*T4x0x/6*T5x0/3*W5x0/W700/3*X2x/4*X3x/3*X4x/5*X6x/3*X6xT/10*X2xx/2*X200T/4*X30x/Z60m/3*Z61x
Comunidad en Español English Community Deutsche Community Русскоязычное Сообщество

Import class without package

hellow, i have a web aplication named test , and i have a class named conexion
when i import a package "pack" with the class conexion, not problem (test/WEB-INF/classes/pack/conexion.class) <% import="pack.* " %> but when i have only the class conexion WITHOUT package (test/WEB-INF/classes/conexion.class) and i import <%import ="conexion" %> i have problem ("The import conexion cannot be resolved") and when i not import the class i have problem (conexion cannot be resolved to a type) , my question is:
how to i import a class without package in JSP , and if the test/WEB-INF/classes is in the classpath when compile the servlet , why the tomcat not found the class conexion?
(tomcat 5.5.20 , jdk 1.5.09 , vim)
thank
(Sorry my english , i'm from Chile)

Hi I am hosting my JSP application with Resin 2.17 which uses classes directly in JSP code (not packages). To make this work I had to specify the classpath in Resin.conf and it worked.
My problem is getting this to work with TomCat or any other application server that will allow me to debug my project in Eclipse or NetBeans IDE. (I have yet to find an IDE that Supports debugging JSP/Java code running on Resin - so I want to switch my application server but I am not sure how to configure my classpath for the application servers to look for java classes in the specified directory just like I did with Resin.

TS5254 bonsoir j ai un probleme de conexion entre mon iphone et ordinateur pour envoyer de la musique ? comment resoudre le probleme merci

bonsoir j ai un probleme de conexion entre mon iphone et ordinateur pour envoyer de la musique ? comment resoudre le probleme merci

Hi,
Title: Good evening, I need help regarding itunes ... Now I do not know exactly what I'm doing but when I open the iPod, I only see the iTunes icon and the icon of the wire ... I will not repeat the error and I want to put music.
Body: Good evening, someone speaks French? Good evening, I need help regarding itunes ... Now I do not know exactly what I'm doing but when I open the iPod, I only see the iTunes icon and the icon of the wire ... I will not repeat the error and I want to put music from what I have in my computer ...How? Thank you C.
When that message appears on the screen, connect your iPod to your computer and open the iTunes software. By syncing your iPod with iTunes, you transfer music from iTunes to your iPod.
Hope this helps!
---likeabird---

PROBLEMAS DE CONEXION CON TV KDL-46W955 Y YOUTUBE

Hola, tengo problemas de conexion cuando me conecto a youtube. Esto suele congelarse el video y luego la pantalla se pone negra, inhabilitando el control remoto.

Bien día PLUIS009,
Gracias por su mensaje. Le hemos enviado un mensaje privado con respecto a su consulta, por favor revise su buzón de entrada.
Atentamente,
Jeannette.

Problema de conexion

Hola buenas tardes, soy de México, tengo un problema con la conexión de red de mi iPhone 4S, no detecta ninguna red wifi, aparece en gris, ya intente varias maneras pero no ha sido posible, quisiera saber si por este medio me pueden dar una solución, se los agradecería mucho.
Carolina Vázquez Ramírez

Hola buenas tardes, soy de México, tengo un problema con la conexión de red de mi iPhone 4S, no detecta ninguna red wifi, aparece en gris, ya intente varias maneras pero no ha sido posible, quisiera saber si por este medio me pueden dar una solución, se los agradecería mucho.
Carolina Vázquez Ramírez

WRT54GS v6 DNS Server problem

Running this router for 2 years without any problems (even on Windows7 since las year), recently it won't let me conect to the internet, Network and Sharing Center say that the pc's configuration are alright but no DNS Server response is present.
(Windows 7 Ultimate x86 RTM, Bellsouth/AT&T ISP in Florida, US. DSL conexion, brand new ethernet cables and hardware kept in the best shape, Network Adapter: Realtek RTL8102E/RTL8103 Family PCI-E Fast Ethernet NIC (NDIS 6.20)(v7.2)
================================================================================
What I tried:
Resetting the router and/or modem (connected to a Westell 6100), setting both to default settings over and over (Web based reset and reset buttons)
IP Flushing in CMD
Getting to the web based configuration for my WRT54GS v6, releasing DCHP, renewing, default settings, etc...
Upgrading firmware to v1.52.7 (latest) to no avail, going back to original 1.52.6.
Device manager shows hardware working properly.
Windows 7 shows me a link to look at the properties of my WRT54GS, when I right click on it, I can also see the option "Enable", but everytime I use it I get "Connection Failed!"
===========================================================================================
I'm not much of a tech guy, and reading the forum didn't help me much, so I'm asking for some help please.
Ps: Installed default CD for it with its old EasyLink Advisor to no avail, also tried the latest Lela 2 EasyLink Advisor to no avail.
Also, there was no Default Gateway looking at an IPCONFIG in CMD, and now there is (192.168.1.1), which I use to get into its web based configuration.
Message Edited by daydreamingby on 02-11-2010 07:49 PM
Message Edited by daydreamingby on 02-11-2010 07:50 PM
Solved!
Go to Solution.

As your ISP is an DSL provider, Most of the DSL Modem has a DHCP on them, so they acts like an Router. So right now you connection type is NAT behind NAT.
To make your Linksys Router work with an DSL Modem. Login to the Linksys Router setup page and below the setup tab you need to change the "Local IP Address" to 192.168.2.1 and click on Save Settings...
Once the settings are saved, unplug the power from Router and Modem, wait for 30sec and then plug the power to the Modem and once all the lights are lid then you can plug the power to the Router and check if you are Online.

Acrobat 7.0 ayuda con la conexion a SQL

Buenas la presente es a ver quien me hace el favor y me ayuda en cuanto al nuevo Adobe 7.0 en el designer con la conexion a SQL mi problema es el siguiente:
Creo un Drop-Down List le hago la conexion pero me da el siguiente error al ejecutarlo:
"connection for source DataConnection failed because the environment is not trusted."
y me muestra solo el primer campo de la conexion a SQL y cuando intento desplegar la lista me da el error
es como cuando trabajas con Visual y el loop es para que lo muestre todos si lo asociamos podriamos decir que en este caso el loop no lo hace
agradezco su colaboracion

Hi,
You should use a different installer for Adobe Acrobat 7. Please find Italian installer for Acrobat.
As its a very old version of Adobe Acrobat, it will be really difficult for you to find Acrobat 7 installer (Italian)
È necessario utilizzare un programma di installazione diverso per Adobe Acrobat 7. Si prega di trovare installatore italiano per Acrobat.
Come la sua una versione molto vecchia di Adobe Acrobat, sarà davvero difficile per voi trovare Acrobat 7 installer (Italiano)

Problem with fax t38 protocol

hi
i have an mpls nework with equipment cisco 2821, 2901 and 2801, and i have problems with fax calls, i configured the fax protocol t38 in all routers but when i want to send a fax to the 2821 equipment from either 2801 and 2901, the protocol t38 is not working and the fax call use cisco protocol (although t38 is configured in all routers). the calls betwen 2801 and 2901 works ok, and from 2821 to 2801/2901 works ok too.
any idea of whats happens? do you think is a problem of ios version?
these are de ios version
2821 .-c2800nm-spservicesk9-mz.124-3i.bin
2801 .- c2801-spservicesk9-mz.150-1.M6.bin
2901 .-c2900-universalk9-mz.SPA.150-1.M7.bin

hi
this is the configuration on the 2821:
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
dial-peer voice 10037 voip
description CONEXION CELAYA DISTRITO XV
destination-pattern 561.
session target ipv4:172.16.200.37
incoming called-number .
dtmf-relay h245-alphanumeric
codec g729r8 bytes 50
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
ip qos dscp ef signaling
no vad
this is the configuration on 2801
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
dial-peer voice 10016 voip
description CONEXION VOZ A FAXES
destination-pattern 300[1-6,8]
session target ipv4:172.1.1.51
incoming called-number .
dtmf-relay h245-alphanumeric
codec g729r8 bytes 50
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
ip qos dscp ef signaling
no vad
i want to use T38 because the bandwidth of the fax call is 16K, if i use cisco protocol the bandwidth reaches up 24k, and the router start to drop voice packets
thanks

Lumia 800 output speaker problem

I have an issue very unconfortable with my lumia 800. When I plug it on my desktop speakers to play music and I want to go to the next song it makes an odd sound like a desconexion/conexion of the jack.
Then if I stop the music I hear like a pulse of sound.
Has somebody the same problem?

I'm having the same issue when i plug the my new Lumia 800 phone on the car audio system.
I had a Samsung Focus, and that problem never happened, so the problem is with the Nokia phone.

I have conexion to router but not the internet

i have conexion to the router but not the internet?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Problems Transporting Infosource

Dear BW Experts:
When I transport an Infosource, all goes active except the transfer rules.
I have connected BW Dev with R/3 Test, and I want to transport to BW Test and connect it to R/3 Test. The source system from R/3 Test is already created in BW Test.
I think I need to configure something.... could it be the conversion table for source system in transport conexion?
Thanks in advance.
Pablo.

hi,
i think oss note 674818 can solve the problem
674818 - RSAR711 - "Error determining a number from object...
Symptom
RSAR711 - "Error determining a number from object... and number 1"
The following objects (number range objects) may be reported:
BI_TSDTEL
BI_TS
Other terms
711 (RSAR), RSAR, 711
Reason and Prerequisites
The number range object intervals cannot be created automatically if the user who executes the transport after-import method is not logged on to the BW-client.
This error usually occurs during the initial transport of transfer rules or transfer structures into a system in which no intervals have yet been created for the number range objects specified above. The after-import method of a transport request runs in client 000. This error occurs because the BW client is a client other than '000'.
Solution
Use transaction SNUM to manually create an interval for the reported number range object. Then repeat the transport or activation.
The number range interval must also be created manually in the production system. A transport is not possible.

Many problems with migration OBIEE

Hi, I upgrade muy proyect obiee 10.2 to 11.1.1.5 and some dashboard displays errors.
Some dashboard error says:
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 46036] Internal Assertion: Condition exceptNode.GetNumLists() >= 2, file server/Query/Optimizer/Request/Src/SQORRqDumpout.cpp, line 336. (HY000)
and others reports says:
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 12002] Socket communication error at call=recv: (Number=9) Bad file descriptor (HY000)
Scenario:
Upgrade OBIEE: windows 32bits(obiee 10.2) to Oracle Linux 5.4 64 bits(obiee 11.1.1.5)
In Windows the rpd created datasource with ODBC and In linux i change conexion in rpd with OCI. I guess the problem can come from this change.I had to change the connection to OCI, but it's weird because I can run some reports and some do not.
thanks

I did not know this could be a problem, however I see the exact version and is:
10.1.3.2.1 to 11.1.1.5
I only upgrade the catalog and on a new machine rpd linux.
Any solutions?
My nick name isn´t rude is a group of music, look for in google:"benito camelas rock and roll"....kids...

Problem while doing insert

Hello.
I'm trying to write the following String containing an XML document, in a MySql database:
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE ReporteHoras SYSTEM "ReporteHoras.dtd">
<ReporteHoras>
<Persona nombre="Daniel">
<Fecha dia="1/11/2004" horas_teoricas="8">
<Proyecto cod="001">
<Tarea nombre="x">
<Horas>8</Horas>
</Tarea>
<Tarea nombre="y">
<Horas>5</Horas>
</Tarea>
</Proyecto>
</Fecha>
<Fecha dia="2/11/2004" horas_teoricas="7">
<Proyecto cod="010">
<Tarea nombre="z">
<Horas>8</Horas>
</Tarea>
</Proyecto>
</Fecha>
</Persona>
</ReporteHoras>
And I get the following exception:
(ReportesReceiver.HorasGMSReceiver 219 ) error al ejecutar tareas SQL: java.sql.SQLException: Syntax error or access violation, message from server: "You have an error in your SQL syntax near 'VALUES ('91750418', 'horasgms', '<?xml version=\"1.0\" encoding=\"UTF-8\"?>\n<!D' at line 1"
4729468 [imqConsumerReader-0-8919380558701437696-0] ERROR starting.src.java.ReportesReceiver.HorasGMSReceiver - error al ejecutar tareas SQL: java.sql.SQLException: Syntax error or access violation, message from server: "You have an error in your SQL syntax near 'VALUES ('91750418', 'horasgms', '<?xml version=\"1.0\" encoding=\"UTF-8\"?>\n<!D' at line 1"
java.sql.SQLException: Syntax error or access violation, message from server: "You have an error in your SQL syntax near 'VALUES ('91750418', 'horasgms', '<?xml version=\"1.0\" encoding=\"UTF-8\"?>\n<!D' at line 1"
at com.mysql.jdbc.MysqlIO.checkErrorPacket(MysqlIO.java:1697)
at com.mysql.jdbc.MysqlIO.sendCommand(MysqlIO.java:1083)
at com.mysql.jdbc.MysqlIO.sqlQueryDirect(MysqlIO.java:1142)
at com.mysql.jdbc.Connection.execSQL(Connection.java:1876)
at com.mysql.jdbc.PreparedStatement.executeInternal(PreparedStatement.java:1590)
at com.mysql.jdbc.PreparedStatement.executeUpdate(PreparedStatement.java:1653)
at com.mysql.jdbc.PreparedStatement.executeUpdate(PreparedStatement.java:1492)
at starting.src.java.ReportesReceiver.HorasGMSReceiver$GMSListener.onMessage(HorasGMSReceiver.java:210)
at com.sun.messaging.jmq.jmsclient.MessageConsumerImpl.deliverAndAcknowledge(MessageConsumerImpl.java:247)
at com.sun.messaging.jmq.jmsclient.MessageConsumerImpl.onMessage(MessageConsumerImpl.java:210)
at com.sun.messaging.jmq.jmsclient.SessionReader.deliver(SessionReader.java:76)
at com.sun.messaging.jmq.jmsclient.ConsumerReader.run(ConsumerReader.java:153)
at java.lang.Thread.run(Thread.java:534)
It seems that the string contains some illegal characters, but I don't know where they are.
I do the following to insert the data:
java.sql.Connection conn = conexion.getDbConn();
PreparedStatement pstmt = conn.prepareStatement(insertSQLString);
pstmt.setString(1, processId.toString());
pstmt.setString(2, "horasgms");
pstmt.setString(3, contenido);
pstmt.executeUpdate();
Can anyone tell me what am I doing wrong?
Thank you in advance.
Regards.
Dani.

> > <?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE ReporteHoras SYSTEM
"ReporteHoras.dtd">This is where the illegal character comes ... I think
it has a problem with "!"
***Annie***Caller = aashu Site = unknown Caller Info. = singh Kind = level1 state = OPEN Errorjava.sql.SQLException: Syntax error or access violation, message from server: "You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near ' Project_Name, Client_Location, Client_Country, Client_Contract_HW INTO client_i' at line 1"
codes as following:-
<%@ page import="java.util.*,java.text.DateFormat, java.io.*,java.net.*,java.sql.*,java.sql.Connection,java.sql.DriverManager,java.sql.Statement"%>
Caller = <%=request.getParameter("caller")%>
     <% String s = request.getParameter("caller");%>
     Site = <%=request.getParameter("site")%>
     <% String s2 = request.getParameter("site");%>
Caller Info. = <%=request.getParameter("callerinfo")%>
     <% String s3 = request.getParameter("callerinfo");%>
     Kind = <%=request.getParameter("kind")%>
     <% String s4 = request.getParameter("kind");%>
state     = <%=request.getParameter("state")%>
     <% String s5 = request.getParameter("state");%>
<%
try
{ Class.forName("com.mysql.jdbc.Driver").newInstance();
                    // String connectionURL ="jdbc:mysql://localhost:3306/client_db1?user=;password=";
               //Connection con = DriverManager.getConnection(connectionURL,"","");
     Connection con = DriverManager.getConnection("jdbc:mysql://localhost:3306/client_db1?user=;password=","","");
     Statement st = con.createStatement();
st.executeUpdate("INSERT Client_Name, Project_Name, Client_Location, Client_Country, Client_Contract_HW INTO client_info values('"+s+"', '"+s2+"', '"+s3+"', '"+s4+"', '"+s5+"')"); %>
<%}
catch(Exception e)
{ out.println("Error"+e);
%>[b]

Problemas conexion 3g

Similar Messages

Maybe you are looking for