Probleme installation Labview

Bonjour,
Je rencontre un problème lorsque j'essaye d'installer Labview. Je l'ai télcharger sur le site de NI et quand je lance l'installation, cette fenêtre apparait et je ne sais pas quoi faire. J'ai essayé de trouvé ce qu'il demandait mais en vain.
Donc merci de m'indiquer si vous avez une solution à ce problème.
Palala

Bonjour Palala,
Avant que cette fenêtre ne s'ouvre, certaines étapes ont bien été réalisées correctement, est-c bien le cas?
Il semblerait que la déstination du support demandé soit celle du DVD de drivers. Généralement cette fenêtre apparait une fois LabVIEW installé, et vous demandant d'inserer le DVD contenant les différents drivers de support (NI-DAQmx...)
Que se passe-t-il si vous appuyez sur le bouton "delcine support"? Il est probable que LabVIEW soit installé sans drivers
Cordialmeent,
Rémi D.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
>> Les rencontres techniques de NI - Mesures et acquisition de données : de la théorie à la mise en ...

Similar Messages

Run-time engine problem in Labview 2009 and Labview 2010

I have a problem with Labview 2009 and Labview 2010. I updated my Labview 2009 into 2010. But it turned out to be a trial one, because i did not have the serial number. So I uninstalled the Labview 2010. however, the funny stuff came over. I cannot use my Labview 2009. So i uninstalled Labview 2009 again. But eventually, I could not reinstall Labview 2009. Every time i had a runtime error and i could not proceed with the installation. in addition, any installation related to Labview is not permitted and the same error came up every time. it is very annoying.
So, What is the deal?
I attached the error here. Any comments or advice are welcomed and appreciated.
Attachments:
error.docx ‏2305 KB

By chance is this machine's language set to any non-English locale? You would check the locale setting by:
Opening Control Panel.
Opening "Regional and Language Options".
Looking Under "Regional Options" >> "Standards and Formats"
If it is set to something besides English, trying setting it to English and please report back what locale it was set to (or if this even solves the problem).
Regards,
- WesW

Distribution problem in labview 2011(Error 11004)

Hi,everyone. I have a problem when i install my build "install". If i include "NI Labview Run-Time Engine 2011" in additional installers, the build files show the error message"
.\Distribution.cpp(2072): InstallerError 11004
Developer Error. Distribution contains invalid dependencies:
1. Product SN1Debug ({4CC67F54-9DD9-4DF2-B9C4-1158C9E9F412}) depends on
product with upgrade code {6AD6C111-233B-4924-A3BF-E4813FE23C7A},
version [11.0.416.0,), language in {}
which is not in the distribution.
Correct the distribution and try again.
<No Debug Message>
" when i install it. and if i don't include it, the install is OK.
I want my distribution include lv2011 run-time engine, how can i do to deal with this problem?
Labview 7.0, 8.0, 8.6,8.6.1,2011
Attachments:
11.png ‏20 KB

Hi,
please try to download and install the NI Labview Run-Time Engine 2011 on your computer and run the builder again.
http://joule.ni.com/nidu/cds/view/p/id/2534/lang/en
In this folder are the installer saved:
C:\Programme\National Instruments\Shared\ProductCache
Regards,
Michael

Problems Installing LabVIEW

Problems Installing LabVIEW Run-Time Engine for Ubuntu 11.04
I'm relatively new to Ubuntu and its community, but have been pleasantly surprised with how easy troubleshooting has been. Unfortunately, I've spent the last two days trying to install the LabVIEW Run-Time Engine, but keep coming up short.
I've tried a number methods from the following threads to no avail:
The problem I'm having now is that despite having the ia32-libs, here is what comes up:
Input: "sudo alien - k --scripts labview-2009-rte-9.0.1-1.i386.rpm"
Response: "labview-2009-rte-9.0.1-1.i386.rpm is for architecture i386; the package cannot be built on this system".
Alien is required because Ubuntu isn't compatible with the .rpm format.
Your help would be immensely appreciated since we use LabVIEW programs to display, manipulate and simulate our spectra.
SZD91
Argumentative Essay

Hey there I'm not too familiar with Ubuntu but you may find some help in the following areas: Linux Users is a group that helps out other linux users. Also labview for linux (Ubuntu 64-bit) my help, people were having a pretty active discussion in there.
I'm guessing you're using the installer from here: LabVIEW Run-Time Engine 2011 -Linux?
Scott A
SSP Product Manager
National Instruments

Problems installation Photoshop Elements 8 on Windows 7

I tried to install Photoshop elements 8 on my Windows 7 computer, but the installation gives a failure after a certain time. A file "...cab" is not working and may be corrupt ( exact failure code I can give, if necesary). Is there any possibility to get this file or the program Photoshop Elements 8 as download file so that I can complete the installation? Thank you in advance for your answers.

Hello,
I just got the same problem already some time ago when I tried to install this programm in my computer. At that time (March 2012) the program crashed my computer, I had to reinstall all the Software completely including system software. The program I purchased in December 2011 from Amazon together with a Reflecta crystal Scan slide scanner as bundle, so I thought it will work.
I will try to install the program from the download link you gave me, in case it does not work, what can I do next without having to buy a newer version?
Regards
Franz-Josef Laven
Date: Tue, 6 Nov 2012 14:57:39 -0700
From: [email protected]
To: [email protected]
Subject: Problems installation Photoshop Elements 8 on Windows 7
Re: Problems installation Photoshop Elements 8 on Windows 7 created by Jeff A Wright in Downloading, Installing, Setting Up - View the full discussion
You can download a fresh copy of the install files by following the directions listed at http://prodesigntools.com/direct-download-links-for-lightroom-3-and-ph otoshop-elements-8.html.
I am curious did you have this installed previously or did you just purchase a copy of Photoshop Elements 8?
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/4828039#4828039
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4828039#4828039
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4828039#4828039. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Downloading, Installing, Setting Up by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

I have a problem, Installation failed

PLease help this is my problem
Installation Failed
Your installation encountered errors.
The error summary file may help you identify the issue
More troubleshooting tps:
1. Restart your computer.
2. Exit all aplications incluiding startup items, virus checking and firewall software.
3. C.ose this window and launch the installer again to reinstall your aplications
If the problems persist, please contact Customer Support for further assitance.
and the error sumary is
Exit Code: 34
-------------------------------------- Summary --------------------------------------
- 1 fatal error(s), 0 error(s), 0 warning(s)
FATAL: Payload '{0A1E2FE2-B2AD-42F4-9C74-641853FB093A} Photoshop Camera Raw 7 6.2.10.0' information not found in Media_db.

Run the Creative Suite Cleaner Tool and try again. If the issues persist, you need to provide more info - we don't even know what product you are trying to install.
Mylenium

Dear frnz, i am doing my prjct in Lview. ie online PQ monitoring. i need to simulate the system with disturbances generated in Lview. so can any bdy plz tel me how to genrte PQ problems in labview. thanks in advance..

dear frnz, i am doing my prjct in Lview. ie online PQ monitoring. i need to simulate the system with disturbances generated in Lview. so can any bdy plz tel me how to genrte PQ problems in labview. thanks in advance..

I work in the power conversion industry and do these types of measurements all the time…
Do you want to just measure power quality or create and measure power quality problems?
What hardware are you using?
Power quality analyzer?
Programmable AC power source?
Fast Transient Generator?
Here is an example of what I do.
To create PQ problems I use a California Instruments AC source set to nominal power for the unit under test. Using Labview I program several transients consisting of fixed and random duration dropouts and surges. I also use a Schaffer Fast Transient Burst Generator to apply high frequency noise bursts directly onto power lines.
For measuring power quality I use a Voltech PM3000A power analyzer and Labview to measure everything from voltage, current, and frequency, to harmonics and %THD
Message Edited by RTSLVU on 07-23-2008 10:31 AM

N'arrive pas à installer Labview student edition

Bonjour,
J'essaie actuellement d'installer Labview 8.2 student edition. Au début de l'installation on me demande logiquement le numéro de série; sauf que sur l'étiquette que je possède je n'ai que deux numéros:
- 1 suivant P/N composé de 6 chiffres, une lettre, un tiret, puis deux chiffres
- 1 suivant S/0: composé de 6 chiffres
Ces deux numéros ne marchent pas... Comment dois je procéder?
Merci

Même problème lorsque j'essaie d'installer sans entrer de numéro de série; il m'indique que mon numéro n'est pas juste...
Message Edité par Romain ANNECY le 05-18-2010 04:36 AM

Installation labview academic license for mac failed

Hi everybody,
I am trying to installa Labview 2008 academic license on my new MacBook Pro with OSX 10.6.3. Every time I start the installation through the mkpg file, the installation starts and then, when it almost finish to run the packages, it stops and fail. Any idea?
thanks

Hi ALVEZ,
You can contact National Instruments and we will send you the CDs.
If you are French customer, the number is 01.57.66.24.24 and ask for the sales departement.
Regards
VéroniqueD
NI France

Trying to include additional installer, LabVIEW wants the wrong distribution

I am trying to build an installer for an application that includes NI-SCOPE 3.7 (3.4 was previously installed, it was removed before loading 3.7). I am trying to include NI-SCOPE 3.7 as an additional installer.
When building the installer, LabVIEW is asking for the NI-SCOPE 3.4 distribution discs. I do not want 3.4, I want 3.7. How do I fix this so that LabVIEW uses 3.7?

Hi User1000,
Could you please verify that NI-Scope 3.4 does not show up in NI Measurement & Automation Explorer under Software. Also, make sure that any NI SCOPE specific VIs that are included in your code are included in 3.7. You could try to deleting those VI's and including them again in the project. Another suggestion I have for you is to try to make a new project and move your code over to the new project and try to build again. Finally, would it be possible for you to include some screenshots or your code?
Regards,
Allison M.
Applications Engineer
National Instruments
ni.com/support

Installer Labview sur un analyseur de fréquence

Bonjour, je souhaiterais utiliser mon programme fait avec Labiew, directement sur l'analyseur de fréquence qui marche sous XP. Est il possible d'installer Labview sur mon appareil, et ensuite le piloter directement? Pour l'instant j'utilise la fonction visa ressource name pour le pilote via usb, Comment faire si je le fais directement de l'analyseur?
Si une personne a déja effectuer cette méthode, je suis preneur d'idée!
Merci d'avance
Résolu !
Accéder à la solution.

- L'installation sur l'OS Windows est possible, maintenant je pense que si vous n'avez pas d'écrans à brancher sur votre appareil je ne vois pas comment installer le logiciel.
Le N9020A possède des entrées USB (Branchement clavier et souris) ainsi qu'un lecteur de DVD-ROM/CD-R/RW. Il ne vous faut plus qu'un ecran pour visualiser votre bureau windows et l'installation de LabVIEW devient possible.
Vous devrez faire attention à la licence NI LabVIEW car si celle-ci ne gère qu'un poste vous ne pourrez pas la faire fonctionner en même temp que celle de votre PC.
Brice S.
National Instruments France

Peut-on installer labview sur un disque de démarrage?

Bonjour,
J'ai une licence labVIEW 8.5 pour Windows. Je souhaiter créer une clé USB portable telle qu'on pourrait avoir avec BartPE ou WinPE. Avec ces outils chargés en mémoire il est possible d'ajouter ou de supprimer des applications.
Ma question est:
Est il possible possible d'installer LabVIEW sur un windows portable?.
Si ce n'est pas possible, est il possible de l'intégrer sur un outil tel que PortableApps ou LiberKey?
Merci

Bonjour
bebop53,
Votre
version de LabVIEW ne peut-être installée sur un Windows portable.
Il existe
des solutions pour développer des
applications LabVIEW sur des OS comme Windows CE en utilisant le Module LabVIEW Mobile.
Je vous
invite à contacter les conseillers avant ventes de chez NI au 01 57 66 24 24,
qui pourront vous conseiller sur les solutions « portable ».
Le support
des 2 outils que vous citez n'est pas reconnu par NI, il y a donc de forte
chance d'incompatibilité
Cordialement,
Cedric F.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
>> Quels que soient votre profil et votre région, vous trouverez la journée qui vous correspond !

Problems with LabVIEW 7.1 and lock-in amplifier Stanford SR530?

Does has anybody had problems with LabVIEW 7.1 and the instrument driver for the lock-in amplifier Stanford SR530?
With LabVIEW 6 there are no problems at all, but with LabVIEW 7.1 it is impossible to communicate with the instrument.

amr_attia wrote: (Private message, no need to private message)
My problem is to get the data out from the divice x and y readings . Can you help me
Here is the code and snippet. I had it from before. It reads Channel 1 and Channel 2 from the SR530, that is whatever the display is for Channel 1 & 2. You set the display manually or programmatically, I let you figure that part out.
Cheers,
mcduff

Installation LabVIEW 2009

Bonjour,
Suite à un problème de disque dur je souhaite réinstaller LabVIEW 2009 mais
je n'y arrive pas.
Le répertoire dans lequel il doit s'installer (C:\Program
Files\National Instruments\LabVIEW 2009\) ne se créé pas, et j'ai remarqué lors
de l'installation qu'au moment du choix des fonctionnalités cette phrase figure
en bas à droite :"Cette fonctionnalité et ses sous-composantes
sélectionnées peuvent nécessiter jusqu'à 0.00 Octets d'espace disque."
Si quelqu'un a une solution.
Merci.
Pierre
Résolu !
Accéder à la solution.

Bonjour,
Probablement que ton système a été mal désinstallé, il reste donc des traces des anciennes installations.
L'installeur croit alors que tout est déjà sur ton PC, et ne tente pas de les réinstaller.
Si je ne m'abuse, dans la sélection des logiciels à installer, tu dois pouvoir le forcer à réinstaller sur le disque dur non?
Si ce n'est pas le cas, je te conseille de telephoner au support techinque NI au 01 57 66 24 24, pour obtenir la procédure de désinstallation complète de tes logiciels NI afain de repartir sur une base saine.
Cordialement,
Olivier L. | Certified LabVIEW Developer

Installation labview 2013

Bonjour, je souhaite installer labview sur plusieurs postes en réseau dans mon lycée.
Mais, voilà, je suis en possession de 2 DVDs : Software labview 2013 + drivers et aussi de 4 DVDs : NI académic Site licence. Faut il obligatoirement installer ces 4 derniers, et à quoi servent ils.
merci d'avance.

Bonjour patrice73,
De mon point de vue, il s'agit de deux suites différentes. Je ne sais pas s'il n'y a que LabVIEW sur votre DVD "Software LabVIEW 2013" ou s'il y a également des modules et des toolkits.
En revanche, pour la suite Academic Site Licence, vous avez sur le premier DVD LabVIEW ainsi que des modules et des toolkits et vous avez d'autres éléments supplémentaires sur les autres DVDs.
Pour faire simple, si vous avez besoin d'installer uniquement LabVIEW, insérez le premier DVD de votre suite Académique. Si vous installez des modules et toolkits supplémentaires, il vous sera demandé durant l'installation d'insérer les bons DVDs.
N'hésitez pas à contacter votre représentant commercial au 01 57 66 24 24 si vous souhaitez plus d'informations.
Cordialement,
Jérémy C.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
Travaux Pratiques d'initiation à LabVIEW et à la mesure
Du 2 au 23 octobre, partout en France

Probleme installation Labview

Similar Messages

Maybe you are looking for