Problems after EFI/airport update

so did the EFI update, there was also a "AirPort Client Update 2009-002" there. and now to my delight i cant get on the internet thorough airport (Ethernet works) i know its not the router because my iphone can connect to it so my macbook should also be abel to. the ethernet cable now runs through the router as well.
so i have now downloaded the "AirPort Client Update 2009-002" again and will see if this solvs it.
(http://www.apple.com/downloads/macosx/apple/application_updates/airportclientupd ate2009002.html)
EDIT: reinstall did nothing. macbook connects to the network but shows a warning "no internet connection"
i am on 10.6.2 and everything up to date from the apple updater.
Airport Firmware version: Broadcom BCM43xx 1.0 (5.10.91.26)
Message was edited by: indeo

sorry no time machine. the router is this
"http://www.jensenscandinavia.com/products/pdf/JensenAirlink_WBR7954EN.pdf"
never done anything other then setting up a WEP password. i am no good with routers so all i can see from this is that its a 54mbps 802.11g.
i also cant find my desktop through the airport so doesn't seem to get any connection. i have tryed to remove the network and retype the password.
ps. ever since 10.6 i sometimes have to manually connect to the desktop computer (cmd+k) this doesn't work either.

Similar Messages

Wifi problem after.4.3 update on xperia z

Hi all,
After updating my Xperia Z (C6603) to build number 10.4.1.B.0.101 I've been having connection issues with every Wi-Fi network.
I've checked the forum but I only found problems about people having Wi-Fi issues with their smartwatch, I do not own a smart watch this is just a general networking issues.
Here's the problem in detail:
When having no Wi-Fi switched on while booting the phone the phone will start without any issues, I will receive my 3G/4G signal and I can browse, e-mail, everything.
Once I switch on Wi-Fi it will start connecting to previously stored Wi-Fi access points but will not connect. Eventually it says that there was a problem with connecting, even though this will take several minutes.
I can go into the Wi-Fi settings, select a different Wi-Fi network (if it is in range) and press connect, however the settings app will freeze at that point and eventually I'll get a notification that the settings app has stopped working.
I have found a "work-around": I switch the Wi-Fi to on, power off the phone and power on again. Now the Wi-Fi connection immediately powers on without an issue once the phone has completely booted, it also will connect to the default Wi-Fi connection that is in range. A different issue appears however once I move out of Wi-Fi range, it will no longer pick up my 3G/4G signal. It is also impossible to switch off Wi-Fi or switch Wi-Fi network connections without rebooting the phone.
As I said before this happened to me after updating to version 10.4.1.B.0.101 after having it received through OTA update. I do not have root access on my phone either so this can't be it.
Is there anyone experiencing the same issues? Is this somehow related to the issues people are experiencing with their smart watch connections (as seen in this topic: http://talk.sonymobile.com/t5/Software-Updates/wifi-problem-after-4-3-update-on-xperia-z/td-p/490591...
If there's anyone who is experiencing the same issues, or has found a fix for this I'd gladly hear from you.
Regards,
Danny
Sony Xperia Z
Modelnumber: C6603
Android version: 4.3
Kernal version: 3.4.0-ge09aff8
Build number: 10.4.1.B.0.101

I faced the same problem. So what u did now to connect your 3g or 4g. Did u tried kitkat update? Its works or not?

After the Airport update today, Airport Utility no longer sees my new Extreme or my 2 new Airport Express relay stations (same network); however, my internet is working and all Airports are green?

After the Airport update today, Airport Utility 6.0 no longer sees my new Extreme or my 2 new Airport Express relay stations (same network); however, my internet is working and all Airports are green? I'm running Lion on my iMac and updated when Airport Utility prompted me to do so a few hours ago. After applying the updates is when Airport Utility stopped seeing my routers. But they are working? Thoughts?

Did you remember to completely power cycle the entire network?
You would want to do this after any update or change to the network.
If you did not do this yet......things are out of sequence.
Power off everything on the network.....all devices.....power down order is not important
Wait a few minutes
Start the modem first and let it run a minute or two by itself
Start the next device connected to the modem the same way
Work your way out on the network starting each device about a minute apart
Check the network

Problems after efi 2.5 update on macbook pro 13 inch(mid 2010)

i don't know if it's related but after i updated my macbook pro 13 inch mid 2010 efi firmware to 2.5 i'm having usb problems.
the problem started after i went to software updates and downloaded efi firmware 2.5, but i didn't restarted right away actually i downloaded the efi firmware around 3pm and shut down my computer around 1am, and in the morning when i turned on my mac it made a strange noise and then restarted. then when it restarted my usb external hd wasn't working well, it takes around 10 minutes for me to be able to watch a video directly from it, and my 3g usb connects but the speed is really slow, so i cant use it. i don't know if efi firmware update is related to usb, but somehow it made my usb ports stoped working properly.
so is there a fix for this?

What you should do is time consuming but really helps (it helped for me)
Go to your disk utility setup and select your harddisk drive, then click on verify disk permissions and after that repair disk permissions, don't ask me why it runs in this order but it seems to elliminate the cause. you will most probably see some repairs being listed.
the next step is to "repair disk" procedure, allthough it could be possible that it can not and then it will tell you to use your setup disk that came with the computer, insert disk hold command and "R" at same time and you come into the menu to repair or re istal software etc.
I ran the repair mode, then re installed my operating software and it seem to resolve this issue but also the long start up problems.
good luck

Network problem after new OSX update download

Greetings!
I've had a new (late 06) Intel 24" iMac networked wirelessly to my older iMac/cable modem/D-Link router very successfully since October. No problems and seamless set-up through the D-Link online wizard software.
Saturday I noticed an OSX upgrade to 10.4.8 (211mg) and went ahead and did the download on the wireless (Intel) iMac.
Upon restart, however, I have not been able to reconnect to my network. Airport is ON, but choosing my network name returns an error message. I have also attempted to reboot both cable modem and router, and reentered the D-Link wizard to both doublecheck the old network, and set up a new network, but saving these settings seems to fail by not recognizing the device, the router.
One of the error messages (on the wireless iMac) claims that my "settings have been changed by another application" (or to that effect) but does not give any clue as to how to determine what or where.
Also, since attempting to start from scrtch with the router, I no longer seem to get a full signal from the airport -- in Internet Connect, I no longer see a nice row of blue signal lights.
As you may be able to tell, I am new to networking, and the D-Link setup had helped make it simple -- tht is, I bumbled my way through it and was pleased with how well it worked. Now, after the OS update, not having the network is annoying -- and potentilly disastrous, as I need this machine online by Saturday.
Anyone able to give me a gentle hand, or nudge in the right direction?
Thanks in advance!
Bill
PS- Mac user since 1991! Wireless network user since only late October!

Hi again,
Sorry, BDAqua, I didn't see your note. I don't quite understand the last line of your suggestion -- a number greater than the number of CPUs? Not sure what you mean...
Phil, thanks for your note, too.
I believe the answer to your first question is 802.11g -- this is what it was set to.
After trying again to connect, using my old passwords, I was able to see the blue signal strength barss, and the Airport icon flashed on and off a few times, but ultimately the connection attempt failed again every time I tried it.
At this point, I'm no longer confident that my router is sending out a recognizable signal -- is this possible?
Also, in the dialog box in which available networks are usually shown (which has not happened since my original connection in October), today I was faced with a choice I hadn't seen before: 2WIRE736 -- is this likely to be someone else's network (a neighbor's)? I was wondering -- I'd never seen that one before. However, my own network names do not show up for choosing, and when I use Internet Connect to request them (and add WPA Personal and passwords), the connection appears to fail immediately.
At this point, should I attempt an OSX reinstall? Or has something I described made some sense for you?
Again, still very appreciative of all your help and patience with my ignorance.
Bill

802.1x Auth Error After Installing AirPort Update 2007-002 and 10.4.9

After installing the AirPort Extreme Update 2007-002 (and 10.4.9, but I doubt that update did it), I am unable to log into my campus's wireless network. I get the message "802.1x Authentication has failed. (Error: 1001 on port en1)"
I've double-checked the settings, and all looks good. Other Macs are able to log in fine but they do not have this update applied.
Other wireless connections from this computer work fine, including using another SSID on this wireless network using WPA/TKIP. Only the 802.1x auth is failing.
I'm a systems admin for the college, and I can see in the radius logs that an error is generated:
"Unexpected error. Possible error in server or client configuration."
I'm the only one getting this error. Anyone have any ideas about this?
Thanks in advance.
truk

I finally discovered what was going on. When doing either the 10.4.9 update or the Airport update, my /System/Library/Keychains/X509Anchors file was either corrupted or completely emptied. The file did remain with 0K size.
I started noticing that all SSL connections from the computer were failing (Safari, iChat, whatever) that depended on the Mac OS X components to do the SSL validation. (Firefox continued to work fine, as it has its own SSL stack.) I then ran the Keychain file check in Keychain, which alerted me to the exact file problem.
My wife also has a MacBook with the same version of Mac OS X, so I was able to copy her X509Anchors file to my computer and everything worked perfectly after that. SSL came back, iChat works, Safari works with SSL, and 802.1x works again.
Hope that helps someone else...

Xfce shortcut problems after today's updates

Xfce shortcuts defined in keyboard settings doesn't work at all, even the default ones like alt+f2. They were still working in the morning, but they stopped after today's updates. I think it has something to do with kbd package, but I can't honestly say.
Anyone experiencing something similar?

Most probably you need to logof, go into the console and wipe anything related to xfce on your home folder and start xfce again. Its a pain to get everything as you want again but at least you avoid problems like the one you have now.
You may also see a problem with the icons, just pull tango-icon-theme and all will be well.

Printing problems after installing Security Update 2015-002

After installing Security Update 2015-002 on three separate computers on two different WiFi networks, printers on the network are losing their connections to the computers that can print to them. We have experienced this on a network running a Canon printer and an HP printer - both have disappeared on the network although the printer suggests it is still connected to the network. The same thing has happened on a separate network I manage with a single HP printer on that network. I have tried removing the printers, resetting the printers etc. Nothing is working. I can get one print out of a printer when I turn the printer off and then on. Three minutes later the printer is no longer connected to the computer - although still connected to the network. Please Help.

I think I have figured out that it is in fact the Apple Extreme Base Station that is losing the printer. It is very odd because the printer is connected to the Wifi. My computer is connected to the WiFi and connecting to the internet. The Router for the internet can see the printer. An Apple Extreme is then connected via a network cable in Bridge mode to the router. When I turned the power off the The Apple Extreme and then restored power it all worked. was still working this morning, but again this afternoon I needed to reboot Apple Extreme. It is quite strange that this is happening on two different Networks in different parts of the country at the same time. Maybe the Security Update is somehow affecting/blocking communication with the printer? I just don't know enough. These networks have been up and running with the same printers and computers for years with zero problems - all of a sudden we have the same problem on both Networks.
Any help will be very much appreciated.

Problem after iOS 6 Update.

I gotta problem after i updated my iPhone 4 to iOS 6. It's a factory unlocked iPhone, then when i change the sim to another network theres no service at all, changed to same network's sim ( the one i am using now, but this one's working fine ) but different number its still no service. But when i use the sim that i used to put in when i updated to iOS 6 its working. Really need someone's help. Its bothering me.
BTW Before even updating i tried all the sims and all are working hella fine.

Try a hard reset.....
Press and hold the Wake / Sleep button and the Home button at the same time, keep them both pressed until the Apple Logo appears.

Has anyone experienced bluetooth problem after iPhone 4 update?

Has anyone experienced bluetooth connecting problems in car after iPhone update for 4.

Hi Barosz2,
If you are having Bluetooth connection issues after a recent update to your iPhone, you may find the troubleshooting steps outlined in the following article helpful:
iOS: Troubleshooting Bluetooth connections
http://support.apple.com/kb/TS4562
Regards,
- Brenden

Finder(?) problem after installing security update 2008-008

I hope someone can help with this problem:
After I installed Security update 2008-008 the finder(?) has begun to behave irratically.
Whenever the mousepad is clicked, the dock slides off to the left and the click is not registered by whichever application I am in. Mostly menus are affected. I now have to click the application and menu item several times before the click is registered.
Safari is particularly badly affected with the pointer jumping around the screen when trying to copy an url (dock keeps sliding to the left), page back/forward doesn't work - url links within web pages are not recognised. Furthermore, when using yahoo mail, menus like 'send' and 'save' are not recognised.
Any suggestions how to resolve this problem would be greatly appreciated!
Andrew

HI Andrew,
This is most likely caused by some 3rd part APP or kext that is now out of date.
Safe Boot , (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, then test your problem there.
Now reboot in regular mode, if the problem didn't happen in Safe Mode, but does in Regular mode, See if there is anything relevant in...
/private/var/run/StartupItems
/Library/StartupItems
/System/Library/StartupItems
Also look in in Your Accounts Pref Pane Login Items window.

Bluetooth problems after Lumia Black update

Just updated my 1020 with the Black update. Now i cant listen to music on my bluetooth headphones. The headset is connected ok (and constantly), the connection doesnt drop. But i only get about a second of music, then 2-5 seconds of silence, then another short burst etc.
Ive tried deleting the headset in bluetooth settings and re-pairing but that did not help. If i just listen through the phone speaker, then there are no dropouts. Headset is fully charged.
Anyone else having issues since the update? Been working fine for over a month before the update.

Ok, managed to fix this now, these are the steps i did though you might not need all of them
Did a soft reset (hold power and volume keys)
Tried going to xbox music, had no download options, couldnt play any music even locally as said i had no license.
Noticed the time and date was wrong after the reset so set that to be correct.
XBox music now works again
Bluetooth headphones now work again.
So perhaps the root cause of the problem was that after the black update, the DRM on the xbox music files was kicking in and once the licencing was working again, all was fine.
Anyway, phew.

Problems After Latest Security Update From March 10, 2015

Is anyone having problems after the latest security update from March 10th?
First my screen went from 16:9 to 4:3 and the resolution turned into a blocky 800 x 600. I managed to find a program
online to correct this problem called SwitchResX. It's unfortunately a pay program for 14 Euro. Here's the link
in case anyone needs it http://www.madrau.com/index.html
Now some alias icons in my dock have disappeared, but are kinda visible when I run my mouse over them, their
names pop up, but have no icons in the dock.
Sometime booting up is clumsy with a lot of hang time and I have to restart my Mac Mini manually by pressing
the button in the back to get a clean bootup to my desktop screen.
Could Apple do a fix real soon for this Security Update blunder?
Any help would be appreciated.

I too experienced problems with the keyboard and mouse on this G5, starting about a week ago when I installed the Java Release 6 and QuickTime 7.3.1 updates. The two symptoms I noticed most were slow, jerky scrolling through topic lists in MT-NewsWatcher (using the arrow keys) and difficulty with selecting text with the mouse in Safari (the selection being anchored several characters away from where I’d begin a click-&-drag).
The latest patch, Security Update 2007-009 (PowerPC) v1.1, seems to have solved the problems for me.

Problem after anti-virus update

Hello everybody.
One of our client uses Oracle XE on a Windows server. Two days ago after an automatic update for the installed anti-virus, Oracle stoped to work. The Listener does't come up any longer. I'm waiting for the listener.log file from the client. In the meanwhile, any idea about this issue? Thank you. Filippo

They said me that the anti-virus is Symantec and doesn't have any firewall service. Even with it down, the problem is still alive.
The part of listener.log when the problem started was:
16-NOV-2006 05:13:54 * service_update * xe * 0
16-NOV-2006 05:15:00 * service_update * xe * 0
16-NOV-2006 05:15:33 * service_update * xe * 0
16-NOV-2006 05:19:24 * service_update * xe * 0
16-NOV-2006 05:27:39 * service_update * xe * 0
16-NOV-2006 05:32:03 * service_update * xe * 0
16-NOV-2006 05:36:27 * service_update * xe * 0
16-NOV-2006 05:46:27 * service_update * xe * 0
16-NOV-2006 05:56:30 * service_update * xe * 0
16-NOV-2006 06:06:33 * service_update * xe * 0
16-NOV-2006 06:16:36 * service_update * xe * 0
16-NOV-2006 06:26:39 * service_update * xe * 0
16-NOV-2006 06:36:42 * service_update * xe * 0
16-NOV-2006 06:56:48 * service_update * xe * 0
16-NOV-2006 07:16:54 * service_update * xe * 0
16-NOV-2006 08:27:15 * service_update * xe * 0
16-NOV-2006 08:47:21 * service_update * xe * 0
16-NOV-2006 09:07:27 * service_update * xe * 0
16-NOV-2006 09:17:30 * service_update * xe * 0
16-NOV-2006 09:22:58 * (CONNECT_DATA=(SID=xe)(CID=(PROGRAM=)(HOST=__jdbc__)(USER=))) * (ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1090)) * establish * xe * 0
16-NOV-2006 09:23:03 * service_update * xe * 0
16-NOV-2006 09:23:34 * (CONNECT_DATA=(SID=xe)(CID=(PROGRAM=)(HOST=__jdbc__)(USER=))) * (ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1096)) * establish * xe * 0
16-NOV-2006 09:23:36 * service_update * xe * 0
16-NOV-2006 09:28:42 * service_update * xe * 0
16-NOV-2006 09:29:06 * service_update * xe * 0
16-NOV-2006 09:29:13 * (CONNECT_DATA=(SID=xe)(CID=(PROGRAM=)(HOST=__jdbc__)(USER=))) * (ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1108)) * establish * xe * 0
16-NOV-2006 09:29:39 * service_update * xe * 0
16-NOV-2006 09:31:40 * (CONNECT_DATA=(SID=xe)(CID=(PROGRAM=)(HOST=__jdbc__)(USER=))) * (ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1119)) * establish * xe * 0
16-NOV-2006 09:31:42 * service_update * xe * 0
16-NOV-2006 09:31:51 * service_update * xe * 0
16-NOV-2006 09:32:24 * service_update * xe * 0
Non pi in ascolto su: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=srvml2.miniliner.locale)(PORT=8080))(Presentation=HTTP)(Session=RAW))
16-NOV-2006 09:38:07 * service_died * xe * 12547
TNS-12547: TNS: contatto perso
TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production on 16-NOV-2006 09:42:53
Copyright (c) 1991, 2005, Oracle. All rights reserved.
Il file dei parametri di sistema �C:\oraclexe\app\oracle\product\10.2.0\server\network\admin\listener.ora
Messaggi di log registrati in C:\oraclexe\app\oracle\product\10.2.0\server\network\log\listener.log
Informazioni di trace registrate in C:\oraclexe\app\oracle\product\10.2.0\server\network\trace\listener.trc
Il livello di trace attuale �0
Avviato con PID=1484
Ascolto su: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC_FOR_XEipc)))
Ascolto su: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=srvml2.miniliner.locale)(PORT=1521)))
Listener completed notification to CRS on start
TIMESTAMP * CONNECT DATA [* PROTOCOL INFO] * EVENT [* SID] * RETURN CODE
16-NOV-2006 09:43:45 * service_register * xe * 0
16-NOV-2006 09:44:00 * service_update * xe * 0
16-NOV-2006 09:44:06 * service_update * xe * 0
16-NOV-2006 09:44:27 * (CONNECT_DATA=(SID=xe)(CID=(PROGRAM=)(HOST=__jdbc__)(USER=))) * (ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1146)) * establish * xe * 0
16-NOV-2006 09:44:27 * service_update * xe * 0
16-NOV-2006 09:52:02 * service_register * CLRExtProc * 0
16-NOV-2006 09:52:02 * service_register * CLRExtProc * 0
16-NOV-2006 09:53:50 * service_update * CLRExtProc * 0
16-NOV-2006 09:55:40 * service_update * CLRExtProc * 0
16-NOV-2006 09:57:29 * service_update * CLRExtProc * 0
16-NOV-2006 09:59:19 * service_update * CLRExtProc * 0
16-NOV-2006 10:01:08 * service_update * CLRExtProc * 0
16-NOV-2006 10:02:57 * service_update * CLRExtProc * 0
16-NOV-2006 10:04:47 * service_update * CLRExtProc * 0
16-NOV-2006 10:06:36 * service_update * CLRExtProc * 0
16-NOV-2006 10:08:25 * service_update * CLRExtProc * 0
16-NOV-2006 10:10:15 * service_update * CLRExtProc * 0
16-NOV-2006 10:12:04 * service_update * CLRExtProc * 0
16-NOV-2006 10:13:54 * service_update * CLRExtProc * 0
16-NOV-2006 10:15:43 * service_update * CLRExtProc * 0
16-NOV-2006 10:17:32 * service_update * CLRExtProc * 0
16-NOV-2006 10:19:22 * service_update * CLRExtProc * 0
16-NOV-2006 10:21:11 * service_update * CLRExtProc * 0
16-NOV-2006 10:23:00 * service_update * CLRExtProc * 0
16-NOV-2006 10:24:50 * service_update * CLRExtProc * 0
16-NOV-2006 10:26:39 * service_update * CLRExtProc * 0
16-NOV-2006 10:28:29 * service_update * CLRExtProc * 0
16-NOV-2006 10:30:18 * service_update * CLRExtProc * 0
16-NOV-2006 10:32:07 * service_update * CLRExtProc * 0
16-NOV-2006 10:33:57 * service_update * CLRExtProc * 0
16-NOV-2006 10:35:46 * service_update * CLRExtProc * 0
16-NOV-2006 10:37:35 * service_update * CLRExtProc * 0
16-NOV-2006 10:39:25 * service_update * CLRExtProc * 0
16-NOV-2006 10:41:14 * service_update * CLRExtProc * 0
16-NOV-2006 10:43:04 * service_update * CLRExtProc * 0
16-NOV-2006 10:44:53 * service_update * CLRExtProc * 0
16-NOV-2006 10:46:42 * service_update * CLRExtProc * 0
16-NOV-2006 10:48:32 * service_update * CLRExtProc * 0
16-NOV-2006 10:50:21 * service_update * CLRExtProc * 0
16-NOV-2006 10:52:10 * service_update * CLRExtProc * 0
16-NOV-2006 10:54:00 * service_update * CLRExtProc * 0
16-NOV-2006 10:55:49 * service_update * CLRExtProc * 0
16-NOV-2006 10:57:39 * service_update * CLRExtProc * 0
16-NOV-2006 10:59:28 * service_update * CLRExtProc * 0
16-NOV-2006 11:01:17 * service_update * CLRExtProc * 0
16-NOV-2006 11:03:07 * service_update * CLRExtProc * 0
16-NOV-2006 11:04:56 * service_update * CLRExtProc * 0
16-NOV-2006 11:06:45 * service_update * CLRExtProc * 0
16-NOV-2006 11:08:35 * service_update * CLRExtProc * 0
16-NOV-2006 11:10:24 * service_update * CLRExtProc * 0
16-NOV-2006 11:12:14 * service_update * CLRExtProc * 0
16-NOV-2006 11:14:03 * service_update * CLRExtProc * 0
16-NOV-2006 11:15:52 * service_update * CLRExtProc * 0
16-NOV-2006 11:16:45 * service_update * xe * 0
16-NOV-2006 11:16:45 * service_update * xe * 0
16-NOV-2006 11:16:47 * service_died * xe * 12547
TNS-12547: TNS: contatto perso
16-NOV-2006 11:16:58 * service_register * xe * 0
16-NOV-2006 11:16:58 * service_update * xe * 0
16-NOV-2006 11:17:04 * service_update * xe * 0
16-NOV-2006 11:17:10 * service_update * xe * 0
16-NOV-2006 11:17:42 * service_update * CLRExtProc * 0
16-NOV-2006 11:19:31 * service_update * CLRExtProc * 0
16-NOV-2006 11:21:20 * service_update * CLRExtProc * 0
16-NOV-2006 11:23:10 * service_update * CLRExtProc * 0
16-NOV-2006 11:24:59 * service_update * CLRExtProc * 0
And 1tnslistener.log is:
TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production on 16-NOV-2006 20:09:29
Copyright (c) 1991, 2005, Oracle. All rights reserved.
Il file dei parametri di sistema C:\oraclexe\app\oracle\product\10.2.0\server\network\admin\listener.ora
Messaggi di log registrati in C:\oraclexe\app\oracle\product\10.2.0\server\network\log\1tnslistener.log
Informazioni di trace registrate in C:\oraclexe\app\oracle\product\10.2.0\server\network\trace\1tnslistener.trc
Il livello di trace attuale 0
Avviato con PID=3136
TNS-01151: Manca il nome del listener, 1TNSListener, in LISTENER.ORA
Thanks a lot
Filippo

BUG: text rendering problems after keyboard firmware update

Hey all!
Just letting you know that today, after installing the keyboard/mouse firmware update 1.0, the font rendering in many applications become weird, letters may overlap, see some screenshots:
http://artemio.net/tmp/apple/bug1.png
http://artemio.net/tmp/apple/bug2.png
My system is iMac Intel Core Duo 17", 2 GB RAM, 250 GB HDD, Mac OS 10.4.6.

Just to clarify, that was a software update, not a firmware update. I don't think the keyboard has any resident firmware.
Since this is a new update from Apple, and there have been very few posts about problems after it was installed, (I have seen a couple here) I think that you should call and speak directly with an Apple Customer Service rep. That way Apple knows some have issues with the update and they may have suggestions.
Let us know what they say.

Problems after EFI/airport update

Similar Messages

Maybe you are looking for