Problems after flashing msi845pe bios version 3.8

hi
i am difficulty after flashing the version 3.8 of the latest bios for msi
845pe max
i was not able to detect my Creative 5.1 sound card , a pci card
pls help

Problems here with verson 3.8 also.
Flashed to version 3.8 and lost both sound and modem (both PCI cards).
Sound card is Creative SoundBlaster 5.1. On-board sound already disabled.
Flashed back to version 3.7 and everything works again.

Similar Messages

K7N2 Delta problem after flashing from 5.0 to 5.3

I was using my K7N2 Delta nicely but after flashing the BIOS from 5.0 to 5.3 in LiveUpdate3 (all OK) and then when LiveUpdate ask to reboot... GOOD BYE!
When bootin the D-lights show that I have a processor damaged or not intalled properly (two red light up, and two green down...).
My processor is an Old Tbird 1.2 Ghz with 100FSB.
The question is: Why the mother stops recognicing the processor if before flashing BIOS worked nicely?.
J10 and J11 jumpers:
When I opened case to check out, I had the green J10 and J11 jumpers closed in the mother. The J10 was in safe mode, and the J11 jumper was closed...(133FSB-166FSB??).
I only have another athlon 1.1 ghz FSB100 processor to test the mobo, but I don´t want to take the risk of burn that one two (if is that the problem, of course).
So... I want to know how can I reflash the bios back (I have the old BIOS in a backup floppy disk, of course)... or if anyone else have the same problem as me....
Thanx a lot guys, and please help me... I´m very sad by now... because I don´t know how to get my computer to work.
Jose.
(from Argentina)

Garry,
Just add
group.Administrators=system
in your filerealm.properties file to login into console.
Hope it helps,
-satya
garry payten wrote:
I am migrating from 5.1 to 7.0 on Solaris. I was able to run the conversion of the weblogic.properties file to config.xml, I was also able to start the new admin server, but I was not able to log in to the console. I get the following error:
Authentication Denied
The username or password has been refused by WebLogic Server. Please try again.
I verified that the WL_USER and WL_PW were correctly set in the startscript and that the system password was set in the config.xml. Any hints? Thanks

[msi k8t neo]problem after flashing to 2.20

hello
i have a MS-6702 (K8T Neo-FIS2R) motherboard and after flashing my bios it shows my ddr400 ram as ddr 333
here is my system config:
athlon 64 2800+
2x256 ddr 400
1x80gb and 1x120gb sata seagate hdd
ati radeon 9600xt
win xp sp1
also please could you tell me if i could use the ddr 533 sticks with my config....
thank you

thanks...
but i think its because the ddrs were made by 2 diff manuf. and the new bios reports the cas lwrong for both both are actually 2.5 but it shows 2.5 for one and 3 for the other....dont know why thuis happened...and cpu-z shows one clocked at 166.7 and the other at 200......
also the ddr 533s would not be able to give their full potential in my config?...
as i am planning to get new ddrs as i have to give these to my bro...

Problem flashing other bios version than 1.2 on 848P NEO

Hi. I had a problem with my MSI-6788 motherboard. It has an AMI bios version 1.2. I had some problems with software because of the Hyper Threading technology. I searched for an option to disable it, but no such option is present in my BIOS setup, but the manual shows it. I wanted to flash another version of BIOS. But, gues what, all versions besides my present one, 1.2, wouldn't work. Please help.

Hi All!
There goes my signature.
I am flashing bios using AMI WinFlash (WinSFI) version 2.04, wich comes with Live Update 3 kit.
I found 1.3 version bios, on the U.S.A. mirror of msi (http://www.msicomputer.com), it is not present on the Taiwan mirror, but as i expected, has BIOS id '1I848XXX'. I will try it, but i don't think it would work. I found another version on the U.S.A. mirror for 848P-VL, version 5.0, tryed it, doesn't work. It had bios id '1I865XXX'.
I find it strange that my chipset is 848P and my bios string (shown at boot time in the botom of the screen) is: 63-1200-001169-00101111-04021-I865G-1I865XXX. As you can see, it includes the string 'I865'. Twice.
AMIBIOS Motherboard Identification Utility v 1.4 detects this:
An AMIBIOS ID String Was Detected:
   63-1200-001169-00101111-040201-I865G
    | | | |
    | | | Chipset/BIOS Info
    | | BIOS Build Date
    | Manufacturer ID
    BIOS ROM Information
AMIBIOS ROM Size: 512 KB
BIOS Build Date: Apr 02 2001
Motherboard Manufacturer Code Detected: 1169 - Micro-Star Int?l Co., Ltd.
Please Consults Micro-Star Int?l Co., Ltd. for support
AMIBIOS Build Tag: 1I865XXX
AMIBIOS Project ID: 1I865XXX Not listed in TAG.DAT file
SMBIOS info:
   Manufacturer : MICRO-STAR INC.
   Product Name : MS-6788
   Version : 10A
   Serial Number: 00000000
So, string 'I865G' should indicate 865G chipset? I found that this chipset comes on the MS-6728 motherboard. I tried to flash the latest version (it had '1I865XXX' bios id in the file), but ofcourse, it did not work. Is it posible that i have MS-6788 motherboard with 865G NEO2 chipset? I'm totaly confused :(.
A last question: I know that a flash memory chip can be written a number of times after wich becomes nonfunctional (at least that what autors of UniFlash utility say). I wonder how many times can i write to this chip, cos i did it enough times by now . All beacuse of that option wich should be present in my bios setup to allow me to enable/disable Hyper Threading. I hope someone would find an answer...

Big problem with KT3 Ultra (ms-6380e v1.0) after flashing the BIOS (de

Hello out there.
I have a real complicated matter with my Kt3 Ultra board.
Used to work fine, but after I flashed it with the latest BIOS (5.7), the board has this strange behaviour: when I clear the CMOS, the board boots up, when I change & save the settings, the board does not "come to life"(black screen & beeper silent).
It has also this weird problem: it shows garbage charaters on the voltage setting of the CPU. Instead of voltages (i.e. 1.750 etc. etc.) I have only "scrambled" strings.
I had MANY difficulties in upgrading the BIOS because the AMI-flashing utility kept telling me "bios protection enabled) (but there was NO bios-protect setting in the previous bios - I checked a zillion times)...but after trying with different revisions finally I made it.
I already tried everything (re-flashed older bios-es etc. etc.)and I'm starting to feel beat ... if you have any advice, please le me know.
It would be really SAD to put this great board in the garbage-dump....
Bye,
Wyk'03

im having problems with this board as well,
i had no problems with the flash,
i did this...
boot to win me floppy,
copy the flash files to ramdrive, flashed to latest bios..
now windows hangs when i have my ac97 audio enabled in bios...
I WANT MY AC97!
hmmm can you get to a dos prompt from a boot disk?
try re-flashing with 1.0 again and then disable the cmos virus protection thingy, and yes it was there it was in the 1.0 bios on the main screen.

Problem after Flashing BIOS on my B490

I have Lenovo IdeaPad b490 I boughted yesterday.
I just find the latest BIOS update for my Notebook.
I have downloaded the latest BIOS update from This Page, but it just downgrade My BIOS version to an earlier version. Before I try to update, the version is 2013. But after update, It show the UEFI version of 2012.
Can I revert The BIOS to the version of 2013?
It also encounter the problem with my Switchable Graphics. The Device Manager told that Geforce GT 720M as my Graphics while I know that my Graphics is Geforce 705M. I also can't use my Nvidia GPU.
Can anyone give me the latest BIOS? Thx..

Quote from: Blazer on 22-July-05, 22:39:17
thats what it sounds like ! contact msi and get a RMA # to return the board,as they can reflash the bios. good luck
How do I do that? It looks like MSIs site is clinically clean of any way to actually contact them...

What to do with bricked motherboard? MSI P67A-G45 AFTER FLASHING LAST BIOS

I flashed MSI P67A-G45 by the last BIOS for IB CPU. The flashing goes twice with intermediate reset. Before I flashed P67A-C43 by the same version from MSI, and all was Ok.
I flashed new BIOS from version 1I under DOS mode. There was a problem with pen drive and I used hard disk without USB pen drive. That was my error. The exe file started and flashed BIOS normally and then after reset started flashing Intel ME firmware. I thought all is going ok and the image is taken from HDD. But after the process finished and motherboard reset, it didn't start at all. The fan starts and stops, LED blinks and motherboard behaves the same way even without CPU. What can I do? Is there any way, suppose, using a EEPROM writer? I have one and I can take the BIOS chip off and flash by old version of BIOS. What can You advise? Maybe the second flash process writes another chip - can You tell me about it. Please advise how to manage this problem.
I received no help from support. I'm not a novice - I work in repair center and have soldering station etc. Can You explain me anything about second flashing process? I need only information and I will be able to manage th :lol_anim:is problem.

Quote from: ring1956 on 31-July-12, 04:01:53
I flashed MSI P67A-G45 by the last BIOS for IB CPU. The flashing goes twice with intermediate reset. Before I flashed P67A-C43 by the same version from MSI, and all was Ok.
I flashed new BIOS from version 1I under DOS mode.
Why did you flash the C43 BIOS on the G45 mainboard?
http://www.msi.com/product/mb/P67A-C43.html#/?div=BIOS
http://www.msi.com/product/mb/P67A-G45--B3-.html#/?div=BIOS

945p neo3 Problem after live update bios

Hi,
After I made the update trought live update, my computer doesn't start, I don't know what to do?
When I restarted it only shows the logo, if I hit DEL or TAB keys it shows to the start of the boot but it freezes.
I already clear the cmos, did anything that i had found on this forum, but nothing works.
I don't have the chance of doing anything because it won't gets the part to enter in bios.
It only appears in the screen thre lines:
AMIBIOS 2005.....
MSI 945PL Neo A7236IMS V1.9 Date: 08/07/06 08:05:52
Intel(R) Core(TM)2 CPU 6400 @ 2.13 GHz , Speed:
and nothing else appears.
One of the things that is very strange is if my board is a 945p neo3 why it happears 945 pl neo, did the live update flash my motherboard with a wrong bios version????
is what it looks.
Any ideas to fix this, if there is a fix?
I don't see anything, because the motherboard don't even reaches the process of boot, so I can't try to flash a other version of bios because the process never reaches the time to boot from floppy, usb, disk..
HELP PLEASE,
Thanks in advance,
Nuno

"Thanks for the ISO File, everything is now correct, the problem with the memory was related with checksum, now happears the 4096 MB."
Nope they was 2 separate problems, solved with one hit.
"About I couln't start your application, whith the historial of your application and antivirus that I saw on the post about it, i got suspecious right away of my antivirus solution.
So to help, I uninstall and after that i could run it, I use Symantec Endpoint Proctection, is the corporate solution from symantec that is replacing the old one known as SAV - Symantec Antivirus Corporate Edition. I didn't find any message in the logs of it, but the fact is that if I have this solution installed I could not run USB tool, if I Uninstall I could run it."
Probably same resource conflict with your AV (some kind of system restriction) which cause Tool unable to proceed properly and terminating itself.
Can't duplicate your issue. I was using SAV - Symantec Antivirus Corporate Edition(Up to date) till now and Tool perform well,
Just installed and updated Symantec Endpoint Protection (Updated to latest definition with all protection activated) and the Tool perform well as expected too.
"now happears the 4096 MB"
Nice

Core center problem after flashing

i have
(2)operating system in my computer (win-98se)
and (win-2k).
newly I have flashing my BIOS with latest version of
liveupdate and now evrytings are running
good.
but whenever corecenter running in my computer in (win-98se)
I see a blue screen with this content:
( A FATAL EXCEPTION 0D HAS ACCURRED AT 0028:E9742715 IN VXD RUSHTOP (01)
+00000245.THE CURRENT APPLICATION WILL BE TERMINATED )
and when runing in (win2k) that have result in restarting the system .
but i dont have this problem with previous BIOS version .
withal :
i have this problem with previous version of core center and latest version
of that after flashig !
can anybody help me ?
[email protected]

What Version of Core-Center are you running?...Sean REILLY875

Sound Problems after Flash 11.3 Update

This reply is to the post by Ortho_Fan, number 28, which references a Firefox forum and "Firefox Hates New Update." This thread is specifically about problems that Flash 11.3 is causing with Firefox but the problem isn't with Firefox, it is with Flash Player 11.3.
I have no sound with Firefox, Chrome or Safari. I do have sound with IE9 but some people do not.
See these and probably other threads:
No sound in flash
http://forums.adobe.com/message/4483563?tstart=0
Problem with sound after update
http://forums.adobe.com/message/4483038

I've branched this discussion into it's own thread, because the issue you're describing is different than the issue from the previous thread, which was related to a specific crash instance. We'd like to keep the threads focused on particular issues to help both investigate and collate the information coming in, and to aid in discovery for people that are experiencing similar issues. A single thread with a dozen issues is far less useful in either regard.
For the sound issue you're experiencing, I would recommend that you follow the advice in the threads you've referenced above.
Flash Player 11.3 included new sound enhancments to facilitate support for low-latency audio, to facilitate more repsonsive sound in complex Flash games. While we try to test a wide array of hardware, and conduct months of beta testing, it's impossible to hit every device, OS, browser and driver combination.
Please ensure that you have the lastet drivers installed for your sound card/chipset. If the problem persists, please post details of your configuration to that forum thread so that we can track down that hardware/driver combo and investigate the problem.
As a workaround, you may wish to roll back to Flash Player 10.3, until a new version is available. Flash Player 10.3 contains up-to-date security patches (we maintain one major version back for Enterprise), and will revert the sound change that is causing problems for you.
http://www.adobe.com/support/flashplayer/downloads.html
Thanks!

Problems after Flash Player update

Hi,
i am writing because i have some strange sensations in my
application after i updated my flash player to version 9,0,115,0.
this is the problem:
i have a dynamic textfield with htmlt text, in this html text
i have some img-tags which i use to add Sprites into the htmltext
that have some kind of user interactivity (rollover, click...).
until now everything worked fine, just with the update i have
the problem that i lost the interactivity to this objects.
just some sprites which have embedded assets from a swf have
the interactivity (rollover, click...) but also jsut on the
embedded symbols and not on the whole sprite.
example: if i put the event on the sprite:
this.addEventListener(MouseEvent.CLICK, doSomething)
the event will be just dispatched if i click on the embedded
symbols.
i tried Security.allowDomain('*') but this didnt solved my
problem
its like i am getting no focus on the sprite.
like i said before... it was working before the update :-(
greetings and thankful for every help!
Pixelista77

Hi Alex, It could be that with the Upgrade to SP2(a major upgrade) it upset Flash Player:-) I've had various glitches when making system changes as well. Then with the 10.1 version of Flash Player being released at the same time, you may have just got caught in the cross fire:-)
It sounds like you did everything correctly, but I just want to touch base on the ActiveX Control not being registered.
When this message is received it can mean the Administrator Account was not used, giving the permissions needed for that. It could also mean that your Anti-Virus/Firewall could have blocked it. Some A/V's even when disabled prior to Uninstalling/Installing, will re-enable upon the first Reboot after the Uninstall.
Let me know on these.
Thanks,
eidnolb

Problem after updating my bios

HY ,i have hp envy 4 model:4-1056txproduct: B9K48PAmy problem start after updating my bios in driver support hp website but when i execute the file my pc retart itselfenow i have problem in the task manager show that i'm using 70% of my RAM (i have 4 GB ) but me using just 300MB of my RAM and my pc so hut .i try to recover my bios by clicking windows + B and start/shut button buuton nothing desplay .can you give me methode to return version of my bios (that cams with my Pc ) .or another thing to resolve the problem .

"verify error" when attempting to flash to bios version 67 on U330

I cannot update my bios version from 54 to 67 on my U330. After downloading the file 0FCN67WW.exe, right-clicking and selecting "run as administrator," it runs for about 3 seconds before a dialog box appears with the error "Verify Error." After that, in order to reboot my machine, it is necessary to unplug and remove the battery to force a shutdown. Does anyone know how to fix this?

Disable any malware protection before.
Flash BIOS update - Flash from Operating System version
for Ideapad Y730, Y330, U330
Version 0FCN67WW
Installation README
This package updates the basic input/output system (BIOS) on
Ideapad Y730, Y330, U330.
BIOS is programming that controls low-level hardware operations,including interactions with diskette drives, hard drives, and thekeyboard. The BIOS is stored on a chip. Your computer uses flashBIOS, which can be updated through a program on a flash disketteso that you do not have to replace the BIOS chip to update theBIOS.
Note: Make note of any settings you have changed in the BIOSConfiguration Utility. These settings may have to be re-enteredafter updating the BIOS.
Attention: Do not under any circumstance power off or restart the system during the Flash update procedure. Doing so will critically damage your system.
Print this file so that you can refer to it during the installation.
Downloading the package
=======================
1. Click the file link to download the file from the web page.
2. When prompted, select a drive and directory in which to save the downloaded file.
Installing the package in Windows 7
======================
1. Locate the file 0FCN67W.exe you just downloaded.
2. Right click the 0FCN67W.exe icon, select 'Run as administrator'.
If the User Access Control (UAC) dialog box pops up, select 'Allow'.
3. A Window will pop up and the message "Are you sure you want to flash BIOS?" will be displayed.
4. Press Enter fo start flashing. During the process, you are advised not to turn off the computer.
5. When the update finishes, it will automatically restart the computer so that the changes will take effect.
Installing the package in Windows Vista
======================
1. Locate the file 0FCN67W.exe you just downloaded.
2. Right click the 0FCN67W.exe icon, select 'Run as administrator'.
If the User Access Control (UAC) dialog box pops up, select 'Allow'.
3. A Window will pop up and the message "Are you sure you want to flash BIOS?" will be displayed.
4. Press Enter fo start flashing. During the process, you are advised not to turn off the computer.
5. When the update finishes, it will automatically restart the computer so that the changes will take effect.
Installing the package in Windows XP
======================
1. Locate the file 0FCN67W.exe you just downloaded.
2. Double-click the 0FCN67W.exe icon.
3. A Window will pop up and the message "Are you sure you want to flash BIOS?" will be displayed.
4. Press Enter fo start flashing. During the process, you are advised not to turn off the computer.
5. When the update finishes, it will automatically restart the computer so that the changes will take effect.
Summary of changes
==================
General Information:
OFCN67WW:
- Update Intel UMA VGA driver to support Windows 7
- Support VT feature
OFCN54WW:
- Power up sound can be muted for quite environments
- Add an option on BIOS menu,
press F2 to enter BIOS -> Advanced -> Boot Logo Volume: 0 (Closed Volume),1(Middle Volume) or 2(Large Volume).
Trademarks
==========
IdeaPad and IdeaCentre are registered trademarks of Lenovo.
Microsoft and Windows are trademarks of Microsoft Corporation in
the United States, other countries, or both.Other company, product,
and service names may be trademarks orservice marks of others.
THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.
WE DISCLAIM ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE
INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, WEGRANT
NO LICENSES TO ANY PATENTS OR COPYRIGHTS.
Copyright (c) Lenovo 2008, all rights reserved
IPnaSh
First Spanish Community Guru - Colaborador ad honorem

Problem after flashing 6156 board

After trying to install a 80 gb hard disk in a computer with a 6156 motherboard, I wanted to flash the BIOS with the version 1.6 one from the MSI website. First, after trying to run the flasher directly from the disk, it just hanged without writing anything. I "fixed" that by using the command /F and forced the flasher to use the flashing code from the onboard bios. That worked a little and the flashing was successful, but now the computer doesn't boot anymore
I can take the bios to an electronics store to get it reflashed, but that will cost, and i'm still uncertain why it didn't work.
1. I read from other threads i found through search that some series of 6156 boards use AMI bios, not Award. The bios chip has a little holographic sticker on it with AWARD written on it, so shouldn't that be an award bios? I can't check the identification string because the computer doesn't boot.
2. If it is an award bios, why didn't my flash work? Could it be that a faulty download leaves a corrupt bios?
3. On the side of the little board where the processor is on, the identification MS6905 is on. Does this mean that I have to flash the bios with the 6905 version?
Right now I'd like to carry the chip to the store and get it flashed with the 6156 bios, but if that doesn't work then I'm out $20 and still at the same place...

http://www.msi.com.tw/program/search/ser/SerConRes.php?Page=2&num=0&DATA=2&SearchKey=6156
there are 3x 6156 models to start
a BX VA and a ZX
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=112
is the only one with a product page and piccy
did you save the old bios wen asked
have you Clear CMOS Guide
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=112
is all that remains of the 6905 ,not evan a bios file
so its not going to be an easy thing to find out
d/l the manuals and compare chip sets etc is all i can suggest

Z68A-GD80(G3) Can no longer read external hd dock after flashing beta bios

I flashed E7672IMS.J31 Beta Bios because I was on a very old bios that was not compatible with my GTX 970 card I just bought. Flashing the bios fixed my 970 compatibility but in the process made it so my 2 external hd docks no longer worked (at this time on windows 7). self powered usb harddrives still worked though. At this time my sata mode was IDE which I thought might have had to do with it since it doesnt have hotswap. I assumed it was an issue with some drivers I installed after flashing the beta bios and I was due for upgrading/reformatting anyways so I enabled AHCI and hot swap then did a clean install of windows 8.1. The external hard drives still don't read!! I've used multiple different hard drives and different usb ports including usb 2.0. The docks are usb 3.0 and I use them daily to edit photos from my work. Any ideas of things I could try?
My pc:
intel 2500k
16gb Corsair vengeance ram
MSI 970 GTX GPU
Corsair 750w power supply
Z68A-GD80(G3) motherboard
E7672IMS.J31 Beta Bios

Could the issue be that I didn't download the Intel Management Driver after installing the beta bios I flashed? Maybe I could try that first, which one from this list do I use with my pc setup?
thanks for the help!
Quote from: flobelix on 20-October-14, 00:38:02
Try going back to E7672IMS.J20 OFFICIAL. Use the recommended flashing method with provided archive only: https://forum-en.msi.com/index.php?topic=163870.msg1215101#msg1215101

Problems after flashing msi845pe bios version 3.8

Similar Messages

Maybe you are looking for