Problems connecting with Nintendo systems

Hello everyone!
Recently, I decided to get a new Linksys router (Model Number WRT120N) for my devices to connect to the internet. Previously, I just had a Nintendo USB connector for my 2 DS and my Wii, but since I intended to get a laptop for school, I got the router.
After setting everything up, the devices all connected just fine. I loved the router, and after trying different things, it worked with everything. However, on Thursday night, they stopped working randomly. All of my devices that were connected could not connect to the router. (That would be my 2 DS lites, my Wii, and my Droid phone)
I checked with each device, and nothing would work. (I don't know if it helps, but my phone would say "Connecting", then "disconnected".)
I tried setting back everything to the default settings and tried again. My phone was the first to work, but now none of my Nintendo devices are connecting.
I've already changed the settings on the Web Admin page for the router (changed it to 1-2 mbps), added the 10 to the IP address. (All of this is from the reccomended page from Nintendo)
I don't know what you guys may need to help me, besides the model number above. If this helps, I'm using the WPA2 Personal security. However, I manually set the 2 DS last time, and they both worked fine. Also, I'm running on a Windows XP system
Long story short: Set up everything on my own, all the devices connected fine. Later in the week, they all stopped working randomly, and I reset the settings. Now after going through everything the same way, only my Droid will connect, and the Nintendo DS and Wii will not.
Any help would be greatly appriciated. Thanks!
PS: I asked the same question on the Nintendo support forum, but there hasn't been a helpful answer that solved my problem yet, so I'm hoping maybe I just set it up wrong. Currently, I'm running the router with no security, as per the request of testing it from a helper on the forum, but they haven't responded back yet.

What I meant by 10 IP addresses was that I added 10 to the last digit of my IP address for the DS systems. (As in, it was 102, so when I manually imput the IP into the DS, it's 112)
I have tried setting the devices to detect the router automatically, but they just connect for about 5 minutes, and then completely loose the signal, and I get a error code on them.
I don't think there are any other wireless channels that are nearby right now.
Should I just reset the router or something? I'm not really sure what to do at this point.

Similar Messages

I am trying to look at my I cloud account on a pc in the library it normally works fine but now says problem connecting with the server. what can i do or is there an issue today

I am trying to look at my I cloud account on a pc in the library it normally works fine but now says problem connecting with the server. what can i do or is there an issue today

Hi...
Try restarting the AMDS > How to restart the Apple Mobile Device Service (AMDS) on Windows
iCloud system status reports everything green > Apple - System Status

Hey guys i got a problem connecting with itunes always giving me ox80090318 if u know the answer please let me know thx

hey guys i got a problem connecting with itunes always giving me ox80090318 if u know the answer please let me know thx

Hello Makiaveli,
It sounds like you are getting this error code when you are trying to access the iTunes Store.
I found this article with this error listed in the symptoms section, for you that should help troubleshoot the issue named:
Apple software on Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123
Resolution
The cause for these issues is a program that monitors the Winsock protocol for Windows conflicting with Apple software. These programs usually use a Layered Service Provider (LSP) that can help identify the particular program installed. The programs that monitor this protocol have a variety of purposes, including security software, content filtering, and optimization of network traffic.
To find the LSP:
Download Autoruns for Windows from Microsoft
Look for Autoruns.ZIP and open the compressed folder.
After reviewing the contents and the license, drag autoruns.exe to the desktop.
Open Autoruns.
Click on the tab that says Winsock Providers.
A list of items should appear. A column showing the publisher should be available.
For items other than Bonjour, which is from Apple, check with the publisher for updates to resolve the conflict between their software and Apple software.
If the publisher is unfamiliar to you, you may be able to use the table below to find out more information about the origin of the modifications to Windows.
Some of the publishers and programs that are known to have versions with a conflict are listed below:
Product or Publisher
LSP Name
Bigfoot Networks / Killer Gaming
BfLLR over [MSAFD Tcpip [TCP/IPv6]]
Bsecure
Bsecure over [MSAFD Tcpip [TCP/IP]]
Bullguard
BGLsp over [MSAFD Tcpip [TCP/IP]]
Bytemobile, Inc.
BMI over [MSAFD Tcpip [TCP/IP]]
CA / Total Defense Internet Security
LAYERED_PROVIDER over [MSAFD Tcpip [TCP/IPv6]]
ContentWatch / Net Nanny
CWALSPSYS CWALSP MSAFD Tcpip [TCP/IP]
Covenant Eyes
Covenant Eyes Monitoring over [MSAFD Tcpip [TCP/IP]]
Dr. Web
DrWebSP.4 over [MSAFD Tcpip [TCP/IP]]
Earthlink Total Access
PropelLSP over [MSAFD Tcpip [TCP/IP]]
Eset
NOD32 protected [MSAFD Tcpip [TCP/IP]]
Fourelle Venturi
VENTURI_TP [MSAFD Tcpip [TCP/IP]]
FoxyProxy
FoxyProxy Service Provider over [MSAFD Tcpip [TCP/IP]]
Hide My IP / My Privacy Tools
My Privacy Tools - LSP over [MSAFD Tcpip [TCP/IP]]
MegaUpload / MegaKey
msadmid over [MSAFD Tcpip [TCP/IP]]
Netintelligence
NIHLSP over [MSAFD Tcpip [TCP/IP]]
Netscape Internet Service
SlipStream LSP over [MSAFD Tcpip [TCP/IP]]
Netsweeper
Liger over [MSAFD Tcpip [TCP/IP]]
Norman/Norman Security Suite
NLF over [MSAFD Tcpip [TCP/IP]]
Panda AntiVirus
PAV_LAYERED over [MSAFD Tcpip [TCP/IP]]
PC Tools / Spyware Doctor
PCTOOLS over [MSAFD Tcpip [TCP/IP]]
PureSight Internet Content Filter
Winsock over MSAFD Tcpip [TCP/IP]
Ratajik Software StationRipper
AVSDA over [MSAFD-Tcpip [TCP/IP]
Safe Eyes / McAfee Family Protection
Internet Content Filter over [MSAFD Tcpip [TCP/IP]]
Sendori
SendoriLSP over [MSAFD Tcpip [TCP/IP]]
SpeedBit Video Accelerator
SBLSP over [MSAFD Tcpip [TCP/IP]]
TellyAbroad
EasyHideIP over [MSAFD Tcpip [TCP/IP]]
Trend Micro
Trend Micro LSP over [MSAFD Tcpip [TCP/IP]]
VMWare
VMCI sockets DGRAM
Wave / Embassy Trust Suite
Wave Systems Kerberos LSP over [MSAFD Tcpip [TCP/IP]]
XFire
Xfire_LSP MSAFD Tcpip [TCP/IP]
Once you've identified the third-party software that installed the LSP, you should check for updates. If the software is your security software, see iTunes: Troubleshooting security software issues for additional information.
Bytemobile is usually associated with cellular data connection software. You may want to check if your provider has instructions to disable or uninstall that portion of the software, such as these instructions from AT&T.
Note: If unsure on the origin of your LSP, you may try to locate vendor information to determine which software is responsible for the non-default value here.
Thank you for using Apple Support Communities.
Cheers,
SterlingD

Lync 2013. There was a problem connecting with the Exchange. Unable to load the magazine discussions.

Lync 2013. There was a problem connecting with the Exchange. Unable to load the magazine discussions.
Installed Lync Server Standart 2013, client PC MS Office 2013.
As the mail system - Lotus Notes Domino Server and Lotus Notes client, respectively.
Exchange is not installed at all.
question:
1 What is the message: "There was a problem connecting with Exchange. Unable to load the magazine discussions." and how it is fraught?
2 How can I fix this message? Cleaning the C: \ Users \% UserName% \ AppData \ Local \ Microsoft \ Office \ 15.0 \ Lync \ does not help
3 What are the disadvantages when using Lync Server Standart 2013 without Exchange? In principle, I put for Lync Exchange?
4 What are the advantages when using Lync Server Standart 2013 with Exchange?
5 Is it possible to work simultaneously Lync Server Standart 2013 + Exchange + Lotus Notes
Thank you.

1) That sounds like a strange translation. But basically, it wants to connect to Exchange and it's complaining.
2) You can attempt to go to Tools->Options->Personal and set Personal Information Manager to None, and in Lync Management Shell run set-csclientpolicy
http://technet.microsoft.com/en-us/library/gg398300.aspx with the following options:
DisableCalendarPresence $True
DisableEmailComparisonCheck $True
EnableExchangeContactSync $False
There may be more, I've never tried to completely disable Exchange features from Lync.
3) No conferencing plugin for meeting invites, no automatic presence management based upon your calendar, no searching your Outlook contacts for new contacts, no voicemail, no conversation history,no unified contact store, and more:
http://technet.microsoft.com/en-us/library/jj688098.aspx
4) This is just #3 in reverse :)
5) Depends on your goals, but the experience wouldn't be great. You'd want to keep your contacts and calendar in Exchange and your email in Notes. It would be confusing to your users.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications

Had to restore ipod to factory settings child forgot passcode. did restore and trying to set up and keep receivng messagethere was a problem connecting with the server

How do I fix this message. When trying to set up the ipod again? There was a problem connecting with the server. please help

Was this the error?
iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server

I am having trouble connecting to a particular person via face time. I dont have any problems connecting with other people

I am having trouble connecting to a particular person via face time. I dont have any problems connecting with other people. They are in Japan I am in Australia. Would that make a difference?

Unable to make or receive FaceTime calls after April 16, 2014

How to verify the Source systems connectivity with BWQ System.

Hi All,
I have diff source systems. And my requirement is to check the source systems connectivity with BWQ (BW Quality sys). please any body tell me the steps how to check the source system connectivity ?
Thanks & Regards,
Manju

Hi Manjula,
If you encounter problems when establishing a connection to your target server, check the following:
A message box appears while performing one of the following actions:
      Setting connection by choosing Apply to local session.
      Testing connection settings by choosing Test settings.
      Creating SAP TSQL objects
If errors occurred, they are displayed in the respective message box.
   Check developer trace files in ST11.
Test connection:
     For RFC related errors, check the RFC connection via SM59
     For database multi-connect errors, check if you can connect to the target SQL Server with the SQL Server Query Analyzer. Also check if the DBCON entries are correct.
Regards,
RK

How to get audio device information connected with MAC system?

I want to know the samplerate (the number of samples per second) supported by the device connected with the MAC system.
I am also pasting the code as below where I need that info.
// Using PCM 44.1 kHz, 16 bit signed,stereo.
          AudioFormat audioFormat = new AudioFormat(AudioFormat.Encoding.PCM_SIGNED, //     the audio encoding technique
          44100.0F,// sampleRate           the number of samples per second
          16,      // sampleSizeInBits the number of bits in each sample
          2,       // channels           the number of channels (1 for mono, 2 for stereo, and so on)
          4,       // frameSize           the number of bytes in each frame
          44100.0F,// frameRate          the number of frames per second
          false); // bigEndian          indicates whether the data for a single sample is stored in big-endian byte order (<code>false</code> means little-endian)

Kanni wrote:
Can you sugget something in that area.That's not an issue that's specific to MAC, it'd be specific to any system with a limited number of supported capture formats.
I've handled this problem in the past by generating an array full of all of the AudioFormat objects I'd consider acceptable, and I just iterate through them until I can find a TargetDataline that supports it.
TargetDataLine tdl = null;
/* Write your own code to get an array of acceptable formats here */
AudioFormat formats[] = JavaSoundFormats.getFormatList();
for (AudioFormat format : formats) {
    DataLine.Info dlinfo = new DataLine.Info(TargetDataLine.class,
                                             format);
        if (AudioSystem.isLineSupported(dlinfo)) {
            try {
                audio_in_format = format;
                tdl = (TargetDataLine)AudioSystem.getLine(dlinfo);
                break;
            catch(LineUnavailableException e) {
                // No need to do anything
/* If we don't have a targetdataoutput object, give up */
if (tdl == null) {
    System.err.println("No TargetDataLines found!");
    System.exit(1);
}

DB Connect WITH BI System

Dear Experts,
I have to connect my BI System with Microsoft Sql Server.
I have read so many standard documents but still not sure how to proceed with it.
My First conern is related to DBSL Library . From where we can downlaod and which file need to be download and where to kept it. ?
Second Concern is user id and password of database. is it necessary same user should exist in both system.(BI System and SQL Server) ?
Third concern : Is there any Specific settings need to activated in SQL Server ?
Please help me as I am not getting exact answer from standard documentation available.
Regards,
Mohit.

Hi there,
Dont' know in BI 7.0 and oracle but I did it once with SQL Server and BI 3.5.
There, tables shown are database views that have been created whit certain conditions like:
User on the connection parameters is bd_owner of the database views.
User have select permisions for the database views
User have db_dladmin
Check requirements for oracle but it seems and autorization problem on the database side.
Hope this helps,
Regards,
Carlos.

I am getting an error message that there is a problem connecting with the service

I am getting an error message that there is a problem trying to connect with the service when I try to convert a pdf to word on my subscription service. I checked to see if my subscription is still active and it is. My account is for Blaise Mazzoni. EMail: [removed]. Please advise asap.
Thank you,
Blaise

Hello, 2 other users in the French forum reported the same issue.: http://forums.adobe.com/thread/1402933 I don't know if there was a particular change in their machine/environment.

WRT300N - Problem Connecting With Desktop

I recently reset my HP desktop to the factory default after experiencing a whole slew of technical issues I had neither intention nor time to deal with. As a result of the reset, I lost connectivity to my host computer which runs a WRT300N Wireless Router. This wasn't a suprise, but I then ran into a few more problems in trying to reconnect. The first issue I experienced was that on my client PC, it wouldn't detect the Wireless PCI Card I previously installed before the factory reset. This was a quick fix, as upon opening the tower, I discovered the card had become disconnected. I connected the card and ran the installation CD successfully. Since the installation program contains a service to select the wireless network you wish to connect to, I did so, and followed the on screen directions to reset my computer. Unfortunately, I was still disconnected from the intended wireless network upon opening up Internet Explorer. I ran the Wirless Zero Configuration service on my computer so I could deal with the wireless networks on more familiar ground. I was completely dumbfounded to what I saw there. It detected the wireless network, but it gives all the wrong information about it. The SSID resembles the actual SSID, but it is not the same. Also, it says that the wireless network is unsecured when, in actuality, is it secured with a WEP Key. I am stumped. A PSP and HP laptop have absolutely no problem connecting to this network. The problem seems to soley exist with my HP desktop. Any help at all would be great. Thank you.

Hi,
Have you tried to install latest drivers for the wireless PCI card.
Download those from www.linksys.com/download from a computer already online.
Transfer those drivers to computer with the wireless PCI card, using a flash drive or by burning a disk.
Uninstall the old drivers from desktop, reboot the desktop computer.
Install the new drivers and again reboot the desktop computer.
Now check for available wireless networks and try to connect to wireless network.

Leopard problem connecting with wifi AP using WPA PSK instead of WEP

I cannot connect via Airport to Speedtouch 580i accesspoint using WPA PSK.
WEP works just fine, but using WPA PSK I keep getting the message invalid password and then cannot connect wirelessly.
Tiger as of version 10.4.3 through .11 worked flawlessly via WPA PSK with the same AP.
I installed 10.5.4 Leopard from scratch and used combo 10.5.5 and and a few days ago combo update 10.5.6 but problem remain.
After the clean install I used migration assistent to get user data and logins from Tiger into Leopard, having used an image made with SuperDuper.
I have read many support forums and suggestions, it all didn't result in a working internet connection at all with WPA PSK :-...(
What I did until now:
- Disabled IPv6 for the airport interface
- Changed to a simple WPA PSK password without CAPITALS instead of something like #A!$($D$%\T@q{|
- Changed to a fixed channel in the wireless accesspoint instead of auto. http://discussions.apple.com/thread.jspa?threadID=1195706
- Rebooted Accesspoint various times.
- Changed to 802.11g only instead of b+g
- Tried both TKIP and AES as encryption type
- Disabled and re-enabled Firewall in Leopard
- Changed to fixed ip adress instead of via DHCP for network addres assignment
- Tried connecting with and without broadcast of SSID to AP.
- Repaired keychain , http://discussions.apple.com/thread.jspa?messageID=5858982
- Did various keychain changes incl deleting old values
- Deleted some items from library, as per suggestions from forums.
In the end I have a suspicion that it all drills down to something simple, quotes (" ") are used to present the password in the password field, at least this is the case with WEP, but this does not harm the functionality for WEP as this is working alright.
With the current WPA PSK implementation it perhaps does influence, because it keeps saying invalid password. I have tested both with and without quotes and things did not improve at all.
I'm running out of ideas to solve this matter, therefore I have sent a report to Apple via their Feedback webpage.
While having using 10.5.5 fo a while I had big hopes 10.5.6 would cure the problem , unfortunately this is not the case.
Please provide more suggestions to solve this problem.

Checked Accesspoint firmware upgrade. The only difference between the current 4.2.7.25 and the latest version, 4.2.7.30 is the support of WDS i.e. expanding the wireless network by connecting 2 APs together (via WEP).
Still tried upgrading via the MAC OS X update software, it did not fire up, I think the software is not fond of Leopards
As WEP works ok with Leopard on my G4 Powerbook 12inch, I didn't want to focus further on the speedtouch because of the motto 'if it ain't broke don't fix it.'
Am going to research more on Keychain and DHCP, others are reporting issues with it along with this 'airport crisis' http://forums.macrumors.com/showthread.php?t=375838

After loading lion, I get an error message "There was a problem connecting with the server. URL's with the type "file" are not supported."

After loading Lion, I have been getting an error message "There was a problem connecting to the server. URLs with the type "file:" are not supported." There does not seem to be any actual problem with internet connectivity, but it is persistent and annoying. Any idea of its cause and treatment?

Take a look at this link, https://discussions.apple.com/message/16156214#16156214

Problem connecting with non-repository owner

I'm using OWB 10gr2 with Oracle DB 10gr2
I've created a repository and can connect with the designer using that repository owner.
Within designer, I enabled another DB user for access (he got the OWB-role "everyone"). He is shown in the gloabl explorer -> security -> users.
But when I try to connect with the designer using the non-repository owner, I get some german error message saying something like "No repository available for this user".
The db user has the database roles OWB_xxx. He can connect to the database and access (read/write) the repository schema.
OMB+> OMBCONNECT o_owbrep/o_owbrep@afxdq008:1521:sdbx USE REPOSITORY 'o_owbrep'
Verbunden.
OMB+> OMBCONNECT f344204/meta@afxdq008:1521:sdbx USE REPOSITORY 'o_owbrep'
OMB01118: Herstellen einer Verbindung zum Repository nicht möglich. (Establishing a connection to the repository is not possible)
PRS-00511: Sie können zum Repository o_owbrep keine Verbindung herstellen, weil es nicht vorhanden ist oder Sie kein registrierter Benutzer sind.
(You cannot connect to the repository o_owbrep because it does not exist or you are not a registered user)
Message was edited by:
user518882
Added results using ombplus.

There are 2 different errors, the latter is a syntax problem. If you own the repository you can connect without the USE REPOSITORY clause.
OMB+> OMBCONN sales/sales@localhost:1521:orcl102
OMB01118: Could not connect to repository! PRS-00510: You need to specify which
repository to work on to establish the database connection.
Simply use:
OMB+> OMBCONN sales/sales@localhost:1521:orcl102 USE REPOSITORY 'OWB'
Connected.
The initial post is something else... the user I connect with in the above statement is also a target user. Should not matter. It is also in Windows XP. Does it work if you use "target user"?
JP

Bussiness Objects connection with R3 systems

Hi,
I would like to connect Bussiness Objects with R3 systems, does anyone have a tutorial or refer any note?
Best Regards,
Nuno Silva

Dennis is right, the connectivity option youo have today is limited to Crystal (unless you wanted to do something purely at the DB layer), but Webi/Universes for ERP are coming in a future release. A prototype is availble at the Innovation Center
SAP BusinessObjects Web Intelligence Reporting for SAP ERP [original link is broken]
Very weird. I only posted this once, but two posts appear??????
Edited by: Pizzaman on Oct 1, 2009 10:57 AM

Problems connecting with Nintendo systems

Similar Messages

Maybe you are looking for