Problems connecting WRE54G with DLINK DWL2100AP Access Point

Please help!!

Hi there,
Your dlink device, is it an access point?
Your range expander, is it version 1 or 2?
Check the wireless settings of your access point and set in the range expande. They need to be exactly the same.
Hope this helps.
"When love and skill work together, expect a masterpiece."

Similar Messages

Problem with Cisco 1240AG Access Points

I have a Cisco 1240AG Access point (P/N ? AIR-LAP1242AG-A-K9).
It has come in the lightweight mode.
I just want to know whether I can put it to the autonomous mode.

Hi Indika,
Here is a conversion method (look most of the way down the attached doc);
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

I have a problem connecting Muse with business catalyst.

I have a problem connecting Muse with business catalyst. When I start the publication is presented with the following message: Timeout when accessing with Adobe ID. Check your network connection and try again. But the connection is working properly.

Hi Federico,
Please go to Edit > Preferences in Muse and make sure the "Publish with Account" has the creative cloud subscription Adobe ID.
Regards,
Aish

Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
-Scott

Forcing iPod Auto connect to the the strongest access point?

I have two access points at home, one on the first floor "platinum 1״ and "platinum 2" on the second floor. How can I force my iPod Touch 4th generation (the newest version) to connect to the the stronger access point?
In many cases I am on the second floor where the wifi signal is stronger from platinum 2 but the iPod stay connected to platinum 1 access point.
I want the iPod to change automatically to the stronger AP at my home.
Please advice

It will stay connected to the current network until the signal strength gets too low to stay connected, then it will switch to another network if available.

Mac mini not keeping connection with Cisco wireless access point

I am trying to get my wife's Mac Mini to keep it's connection with the wireless network at her school. They are using a Cisco access point (not sure of the model) which works fine with my G4 Powerbook and the numerous Macbooks being used there, but for some reason her Mac Mini drops the connection after 4 or 5 minutes, at which point she needs to log right off for it to reconnect (as opposed to just turning the card off and on again). I have already gone through the deletion of the Networkinterfaces.plist file, and recreation of the Airport card profile process, but this only kept the interface active for about 36 hours, then it was back to the same old problem. At this point I am thinking "flakey card"...before I ship it off to Apple, can anyone offer any other possible solutions?

After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!

IPhone will not sync with Cisco Wireless Access Point

This is unbelievable, i just bought a $1000 phone and it wont sync with a Cisco AP. I can sync it with a DLINK? I there a specific list of Access Points it will connect to. If so thats complete bullsh*(. Also, is there going to be a firmware update soon to fix these problems. Can you tell that im a little upset. I just saying that if someone spends $1000 dollars on a phone it should be working pretty dam good. Anyway can someone offer any suggestions?
Upset Iphone user.

After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!

Macbook Wireless Driver Incompatible with Dual Band Access Points & PPTP VPN with MPPE Enabled.

Configuration:
Local Client: Macbook Pro 8,1 (Dual boot 10.8.2 & Windows 7 x64)
Local WLAN AP: WiFi dual band access points (I do not have admin access to)
ISP: TWC Road Runner
External VPN Server: Poptop PPTPD server v1.3.4 (I do have admin access to)
Problem:
There is a Macbook BCM4331 driver incompatibility that spans across both OS X and Windows 7 when connecting to a PPTP VPN through a local dual band access point.
The same Macbook (booted into either OS X 10.8 or Windows 7) cannot maintain a ping/connection to the PPTP server when connected to a local dual band (2.4GHZ/5GHZ) WiFi access point.
Macbook connects and remains connected to the PPTP server (as shown in connection status,) but no traffic will pass through VPN once the connection has "dropped" internet traffic. Flood ping to the VPN server initially replies with expected <30ms ping time. Once internet traffic is passed across VPN, ping fails and traffic stops completely.
• Any other wifi client machines & OS using same dual band AP can connect to VPN and maintain flood ping to PPTP server and pass all traffic or even split tunnel. I've tested different computers using Windows XP, Windows 7, Android 4.1, iOS 6.0.1 etc. No problems at all.
• Macbook can maintain flood ping and pass traffic to PPTP server when connected to a different standard 2.4GHZ access point.
• Macbook can maintain flood ping and pass traffic to PPTP server when connected via Ethernet on same LAN as dual band AP's.
• Macbook can maintain connection/ping by disabiling MPPE encryption on the PPTP server. Running an unencrypted VPN is not an option for me however.
• Macbook can maintain connection/ping whenn booted into Windows 7 natively and disabling 2.4 band through Device Manager > Advanced tab > Disable bands > "Disable 802.11g/b".
To fix this problem, I would propose that Apple allow OS X users to disable 2.4GHZ in OS X. Doing so should allow PPTP + MPPE when connected via dual band routers as it does in Windows 7. I think asking them to rewrite the driver for OS X & Windows 7 is asking too much.
Credits:
I have been through so many forums, reconfigured the Macbook, the PPTP server, reformatted, tested and tweaked until my eyes bled. Here is a collection of threads of others with similar problems:
https://discussions.apple.com/thread/2778039?start=120&tstart=0
https://discussions.apple.com/thread/3202997?start=0&tstart=0
https://discussions.apple.com/thread/2136112?start=15&tstart=0
http://forums.macrumors.com/showthread.php?t=196438
https://discussions.apple.com/thread/2132652?start=0&tstart=0
http://comments.gmane.org/gmane.network.poptop/2373
https://discussions.apple.com/thread/1623154?start=0&tstart=0
https://discussions.apple.com/message/12514921?messageID=12514921#12514921
http://forums.macrumors.com/showthread.php?t=1101053
http://forums.macrumors.com/showthread.php?t=415087
https://discussions.apple.com/thread/1346301?start=0&tstart=0
https://discussions.apple.com/thread/2197122?start=0&tstart=0

I haven't heard anything back yet. I will update if I do.
Being that Apple takes pride in selling their own computers and writing their own drivers & software to match, the Macbook with OS X 10.8 should be a super polished, finely tuned machine. It's aggravating when I can't do relatively simple things which I can do on any other device & OS:
If you've read the first post, you know it's not possible to pass PPTP + MPPE on the Macbook Pro 8,1 with OS X 10.6+ or Windows 7 when connected to a dual band AP.
OS X also imposes a 130mbps limit on the 2.4Ghz band. I have no problems connecting @ 450mbps on 2.4Ghz with Windows 7. The range is much better than 5Ghz as expected when there aren't any neighboring AP's for interference. I've also never received interference with Bluetooth devices.
There have been a couple times where some things don't plain work right and the flexibility to fix them as an "Apple knows better than the user" policy is restricted. In most cases, perhaps Apple does know better. In this case, there is definitely a problem with the BCM4331 driver. If it "just worked" this topic wouldn't have been created.

PoE auto switchover with Cisco 1252 Access Point.

Dear All
I have a network for Managed Wireless using Cisco. This is a new network for me.
I am in problem with Cisco Access Point 1252. My AP's are connected to a PoE Switch. And Cisco AP's are also connected Powered with also Power Adapter with UPS backup.
But problem is if I disconnect power source of AP Power Adapter , AP is not getting up with PoE. PoE is up only when POWER PLUG of AP ADAPTER is physically pulled out from Socket.
Question is if it is possible to make automatic Failover by PoE when Power source of AP ADAPTER is down ?? I mean no need to PULL OUT POWER PLUG of AP ADAPTER.
Waiting for your rely.
It is very urgent .
Thanking You
Subrun.

Hi Suburn,
1- yes it is possible to do failover without unlupping the cable of AC adapter. When power on ACS adapter is off, then the faiolver happens.
2- with regards to POE, if your switch supporting enhanced POE?
Powering the Aironet 1250 Series Access Point with Cisco Enhanced PoE
Cisco Enhanced PoE was designed for customers who want to install new PoE-enabled technologies that require greater than 15.4W per port to function at full capability, such as wireless technology based on the IEEE 802.11n standard. Cisco Enhanced PoE provides the full power requirements for dual-radio modules and eliminates the need to run an additional cabling drop or insert a separate power injector. Support for Enhanced PoE is currently available on a variety of Cisco Catalyst® switching platforms. For more information on Enhanced PoE, visit http://www.cisco.com/en/US/prod/switches/epoe.html.
Serge

Problem connecting wirelessly with home hub 3.

Kodak gave me advice onthis problem. Entered security key in upper case instead of lower and it solved the problem . No help from BT on this.

paulweekspat wrote:
trying to connect kodak printer. i have resolved the issue with help from kodak. bt was no help at all. thanks anyway.
What john46 says is quite correct, also Kodak would give you NO support for setting up the Home Hub..
Thats not to say you would not have been given help on these forums if you had a problem connecting your printer and if we could not help,at least we might have been able to point you in the right direction.
http://support.en.kodak.co.uk/app/home/selected/true
toekneem
http://www.no2nuisancecalls.net
(EASBF)

Help with N97 and Access points after V20 upgrade

Hi Guys,
I'm hoping someone can help me - I have an 505 uk unit and have changed to a generic euro product code to get the V20 software ( as theres a 2 week wait minimum for the network to release its custome version ) and its working brilliantly - except - in connections all my accesspoints have gone - I now show 13 uncategorised access points which I cant expand or open and it wont let me delete the lot as it says its protected Anyone able to sort this out and tell me what to do so I can get back to Internet and Contract WAP etc... destinations?
Much Appreciating any help.
Alex

Hi Alex,
I am not sure what kind of applications are preloaded in your location. I suppose the problem you faced is unable to delete certain definitions under the Destinations setting?
If a hard reset is not an option (not for me as I have purchased apps from the OVI store), I would create a dummy Destination to house all these unwanted definitions. That way, so long as the default connection does not utilize this dummy Destination, I think you are OK. Hope this helps.
Visit http://www.WilfridWong.com - where all good things are meant to be shared!

Newbie help with Aironet 1200 access point

Hello everybody,
We "inherited" an Aironet 1200 access point with antenna's throughout our building. This was installed by a company that thought they would make money selling Wi-Fi access but now they have gone bankrupt.
We eliminated their router and installed one of our own, and we have it handing out IP addresses. When I plug it into the Aironet 1200 it works just fine. Users are able to connect wirelessly and access the internet.
I would like to change the SSID however so that it no longer reflects the now defunct companies name.
I cannot determine what IP address is assigned to the access point so I can't figure out how to access the management page.
I tried connecting to the ethernet port via a DB9 to RJ45 cable and hyper terminal. After connecting the cable and powering up the access point I am still unable to connect.
I realize once I get connected I will probably run into password issues, but I'd like to figure out how to get at least that far.
Any ideas?

since ur gonna change the ssid and there is a password...
1. reset the ap. before plugging power to ap, press hold the mode button for 3 sec or until the led becomes orange or amber, then release.
2. the ap is reset to default setting with ip address 10.0.0.1
3. either console or gui the ap and change the bvi to ur preferred ip address.
4. configure everything else as you want.

WRVS4400N v1 Router with 3 WRT600N (Access Points) locks Internet access

Have the following equipment
1. WRVS4400N (DHCP Services and connected to DSL modem on different subnets, QuickVPN enabled but not working)
2. 3 WRT600N used as Access Points troughout the house connected to the ports on the above router
The problem is that after working for a while the internet access locks out.... although the wireless laptops get an IP address and can see other network equipment they can't access the internet. After a restart on the WRVS4400N everything works again.
If I connect to one of the ports on the DSL everything is always working. So what could be causing the problem? I don't want the client to have to restart the WRVS4400n router every day.
Any ideas?

Please update the WRVS4400N v1 to the latest code. The new code fixes some of the DHCP issues
http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=Wireless+Router+Firmware&mdfid=282446893&treeName=Routers&mdfLevel=Model&url=null&modelName=Cisco+WRVS4400N+Wireless-N+Gigabit+Security+Router+-+VPN+V1.0+%26+V1.1&isPlatform=N&treeMdfId=268437899&modifmdfid=null&imname=&hybrid=Y&imst=N

Cisco 2500 controller with aironet 1600 access point

Hi,
This my first wireless project, and I have a few questions about the installation :
1- some of the access point will be installed in branch offices, connected to the controller through the main MPLS netwrok ( is that possible).
2- If for any reason the connectivity between the AP and the controller get disconnected what will happend to the users connected to the access point.
3- can I have two vlan on the Aironet 1600, the first one to be connected to the controller through the MPLS netwrok and the second for users to public internet.(internet break out).
Thanks,

Yes that setup will work. What the others are trying to explain is authentication if your WAN goes down. If your AP's are setup for FlexConnect and you are indeed using AP groups, (using 802.1x) you need to have a radius server and a backup AD sever to allow for authentication to still happen if the WAN goes down. If you have resources centralized, then when the WAN goes down, everything else goes down and no new authentications will take place and any re-authentications will fail with 802.1x.
Take a look at these links
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/flexconnect/config_flexconnect_chapter_011.html
Sent from Cisco Technical Support iPhone App

There is no communication between devices which are connected to Linksys Wireless WAP4410N Access Point ?

Dear all,
     I deployed new Linksys Wireless WAP4410N Access Point and it is working fine. Laptop which is connected to AP can able to access internet. It can able to communicate with AP and also the gateway IP(Router IP) but the issue is wireless devices are not able to communicate between them. In the case LAN device can communicate between wireless devices. Can't able to share files between wireless devices.
     Please help me to troubleshoot this issue. Wat could be the issue over here. Wat step i have to take to clear this issue.
     Advance in thanks.
Thanks and regards,
Chandhuru.M

Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
Under Wireless/Security how do you have the Wireless Isolation configured?
Wireless Isolation (within SSID) should be disabled to allow wireless computers associated to the same SSID to see and transfer files between each other
Thanks
Eric Moyers    .:|:.:|:.
Cisco Small Business US STAC Advanced Support Engineer
CCNA, CCNA-Wireless
866-606-1866
Mon - Fri 09:00 - 18:00 (UTC - 05:00)
*Please rate the Post so other will know when an answer has been found.

Problems connecting WRE54G with DLINK DWL2100AP Access Point

Similar Messages

Maybe you are looking for