Problems in launch pad

in launch pad i see a lot of applications which i dont need how to close these ? i feel all these short cuts are not needed by me how to drag these closed/

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Similar Messages

Problem to open collaboration launch pad

Hi,
I'm trying activate an instant messaging service in my portal.
I've activated the collaboration launch pad, but when I click on the link I get the following error:
"An exception occurred during the program execution. Below you will find technical information pertaining to this exception that you might want to forward to your system administrator.
Exception Class -> class com.sapportals.wcm.WcmException
Exception Message -> Cannot get an instance of the presence state service"
Which can the problem be? I use this version in my portal:
6.0.2.39.0.Enterprise_Portal_Support_Package_2
6.0.2.39.0.ContentManagement_Collaboration
Thanks in advance,
Samantha.

Hi Samantha,
Hope this helps
/thread/198785 [original link is broken]
http://help.sap.com/saphelp_nw2004s/helpdata/en/f2/341c5647630f42bd98323aa64b5661/frameset.htm
Thanks N Regards
Santosh
Reward if helpful !!!

Problem with Collaboration Launch Pad

Hi all,
We have a problem with collaboration launch pad, when one user access it, always appear offline.
Status is automatic for all portal users.
We have configured RTC following documentation in help.sap
Can somebody help us?
Best regards.
Gabriel Garcia.

Hi Robert,
We are using Netweaver 7.00 SP9 with same version for Enterprise Portal and KM.
We were searching more information about our problem in SDN and SAP Notes but we couldn´t find any solution.
Thanks for your response.
Gabriel Garcia.

KM Collaboration Launch Pad Problem

Hi , I am using EP6 .
The Portal shows link for Collaboration Launch Pad but whenever i click over it the following error is occuring:
Exception Class: class com.sapportals.wcm.WcmException
Exception Message : Cannot get an instance of the presence state service
Pls help me solve this problem.

Hello Vinod,
Check this:
https://www.sdn.sap.com/irj/sdn/thread?threadID=177728
Greetings,
Praveen Gudapati
p.s. Points are always welcome for helpful answers

Collaboration Launch Pad (CLP) problem

Hi,
We have implemented a Federated Portal Network. Our purpose is setting
a chat between both federated portals.
We have a problem when we activate the link for Launching the
Collaboration Launch Pad (CLP) in the consumer portal (EP7 SP10). The
producer portal is EP7 SP10 too.
Once done the steps indicated, the collaboration link is not displayed
in the consumer portal tool area if the language is specified in
english. However, if we change the language to spanish, the
collaboration link appears. In the producer portal occurs the same
problem: the collaboration link only appears if the language is spanish.
If we try to send a instant message through the CLP to other user, we
get the following error:
Error en tiempo de ejecución del portal
"Error ocurrido durante el proceso de una solicitud para :
iView : com.sap.netweaver.coll.appl.ui.base.UpcmSession
Componente : com.sap.netweaver.coll.appl.ui.base.UpcmSession
Se ha grabado excepción en log. Diríjase al responsable del sistema.
Exception id: 08:31_28/09/07_0020_11593350
See the details for the exception ID in the log file"
What is the problem? Why is it necessary to use spanish language?
Thanks in advance,
Samantha.

Hi,
perhaps your user is set to have the lightweight framework and not the default in the master rule collection.
Then you should enable the CLP in the lightweight as well.
Regards,
Manuel

Collaboration Launch Pad as iview in the Portal content

Hi friends,
i have the following problem. I configured the collaboration launch pad (real time collaboration) and it works fine.
I just don´t want to start the iview from the collaboration link next to the TREX search. Instead of that i need the iview with the user status and the possibility to start an instant message session within the portal content.
Does anyone know if it is possible and what is the name of the corresponding iview?
Thanks in advance
Michael

Hi Michael
Create an new iView (new from PAR => iView) and select the com.sap.netweaver.coll.shared.ui
Create a link in the iView to the contacts:
In the iView properties add in field "Path for Initially Displayed Folder": /alias/%3Cmycontacts%3E
and in field "Path for Start Uri": /alias/<mycontacts>
Hope this helps.
This worked, but I needed also to activate the Tool Area with activated CLP link. I didn't get it work without Tool Area.
Regards,
Stefan

Status error in Collaboration Launch Pad

I still got always an exeption message
"Service not found: RTCClientAwareness"
if I try to change the status of my account in the Collaboration Launch Pad. I had everything done described in nw04 help administration document to run RTC although RTC is not working. Any ideas? (by the way, I had used Rapid Installer 2.0 to install EP6.0 on WAS 6.40.)

Did you ever solve this problem? I'm haveing the same problem...

Screen flicker on rMBP (in launch pad)

Hi all, I've recently installed Mountain Lion and am getting a screen flicker in launch pad. I was wondering if anyone else is experiencing this issue?
The problem arises when you try and access a folder of applications in launch pad.
I have a MacBook Pro retina. 2.3Ghz; 16Gb ram; 250Gb.

I'm having a similar problem with the dock when I'm using my 720p television as a second monitor through the HDMI connection on my rMBP. I've attached a couple of screen shots for your information, and to show the apple reps when I call them back ...
Up to this point, I clean installed Mountain Lion and started a fresh user account. I didn't notice the "jitter" at that point. So, I reinstalled ML for a second time, using the account migration feature without transferring my settings. The jittering dock returns.
What next?

An Error Occurred during CHART Generation in BI Launch Pad 4.0

Hi Guys,
I am creating a report on BI launch Pad, the query result shows fine in the "Table" format but when i "Turn Into" chart it gives me an error " An Error Occurred During chart generation, The chart cannot be displayed".
I created the same report in Rich Client and everything is working fine but on the portal the charts cannot be displayed.
Let me know if anyone has faced this error or has any solution for it.
Thanks in Advance,
Sheikh Hassan Ayub

try the following:
1) We created a new Adaptive Processing server by stopping the existing one.
2) Enabled and Started the new server.
3) And now you were successfully able to Create, Open and Modify any web Intelligence reports in BI Launchpad.
It worked for me.
But the problem is that i had to re create the charts in BI launch pad, the old charts didnt work.
If you have any other solution let me know.
Sheikh Hassan Ayub

ODBC error in BI Launch pad

hi,
am very new to SAP BI/BW/BO
i am getting error while running the query in BI launch pad, which i imported from the UDT
in UDT the values are being displayed and all the parameters were clearly defined
the query is being running perfectly in RICH CLIENT but the same query unv file is not been running in BI launchpad
where would be the actual problem ????
NOTE:
its showing ODBC error and no default drivers specified.
but as i mentioned above , its displaying the values in UDT and Rich client ( Enterprise ) mode but not in BI Launchpad.
please help me out..?
specifications:
SAP business intelligence 4.1
32 bit windows home premium

Santosh,
Create the same ODBC connection in server also, so that you will be able to view in BI Launchpad also.

BEx launch Pad not opening smoothly

Dear All,
I am using the SAP BI 7.0. I am facing problem in BEx (Version 7) Launch pad opening for Query.
sometime it opens the launchpad while other time ..it is mot opening the launch pad.
The patch Level is as below:
SAP_ABA     700     0016                    SAPKA70016
SAP_BASIS     700     0016     SAPKB70016
ST-PI     2005_1_700     0006     SAPKITLQI6
PI_BASIS     2006_1_700     0006     SAPKIPYM06
SAP_BW     700     0018     SAPKW70018
BI_CONT     703     0011     SAPKIBIIQ1
ST-A/PI     01K_BCO700     0000          -
Please suggest solution.
Regards
Vimal

Try upgrading to GUI 710 patch 11
SAP Frontend Components
SAP GUI FOR WINDOWS
SAP GUI FOR WINDOWS 7.10 CORE
SAP GUI FOR WINDOWS 7.10 CORE
win32
gui710_11-10002995.exe
BI ADDON FOR SAP GUI
BI 7.0 ADDON FOR SAP GUI 7.10
BI 7.0 ADDON FOR SAP GUI 7.10
Win32
bi710sp08_800-10004472.exe
install in the following order:
SAP GUI -> BI Addon for SAP GUI -> SAP GUI patch
pts appreciated

BI 4.0 Launch Pad will Freeze When Attempting to Schedule a Report

I recently set up BI 4.0 Edge series onto my server running MicroSoft server 2008 R2. The install completed without error so I began implementing 'Best Practice' Crystal Reports. When attempting to schedule these reports within the BI 4.0 launch pad I ran into an issue.
After clicking 'Schedule' the IE browser freezes with the schedule options available to be seen but not interact with and the loading pinwheel frozen in the center of the screen.
I am running IE9 but I have run both IE8 and IE9 on other systems without fail so I don't think that's the issue. I've also tried resizing the APS to allow more RAM to the platform processes as well as split the services into separate servers all without success.
The browser also freezes when I attempt to click the 'Preferences' button on the launch pad home page, but I can open the Web Intelligence Application with no problems.
This is a particularly frustrating issue since I can navigate within the CMC with excellent response time from the system. The rest of the launch pad is as reponsive as the CMC. I can navigate in and out of folders fine, but when I try any command by right-clicking on a report
If anyone has any suggestions on what could be causing the browser to freeze during these transactions I would greatly appreciate it. Iu2019ve tried to run a Repair on the Edge series application and I would like to avoid a complete re-install.

Only IE8 is supported, how about another browser like Firefox on same machine. No need to re-install, you can try to undeploy -> redeploy the web app using WDeploy but it seems to be machine specific.

Slow Performance BI Launch Pad - BI 4 SP2 patch 8

Hi experts, i have this seriuos problem: i have installed BI 4 SP2 patch 8 on windows server 2008 server based on 12 GB Ram but when tree user access at the same time at BI Launch Pad, the server has an lowering performance and to access in BI Launc pad is necessary attend long time.
Could you help me? Are there some configuration parameters to set?
Thank's a lot.
Andrea

This is what I received from SAP:
- It is a bug in the BI 4.0 product and an ADAPT01711291 has
been raised for the same.
- Please go through the attached KBA '1933935 - BI Launchpad search
failing with error "The property with ID SI_CUID does not exist in the
object" for non-Admin users' for more information.
- As per the ADAPT details, it is targeted to be fixed in BI 4.0 SP10
which is scheduled to release in July 2014 week 30
- The schedule is subject is to change without prior notice. You can
regularly check the SAP BusinessObjects maintenance schedule on the
following link on SAP service marketplace
SAP Support portal -> Software Downloads ->SAP Software Download
Center -> Support Packages and Patches -> SAP Support Package stacks
- You are using BI 4.1 SP2 and I did not find information about
inclusion of fix of this issue in release notes of latest Service
packs of BI 4.1 (SP3 or SP4)
- So as per my knowledge you will have to wait for BI 4.0 SP 10 to
release and the releases of BI 4.1 post to that will have the fix of
this issue.

BI Launch pad - error opening WebI documents

Hello,
We have newly installed BusinessObjects Enterprise XI 4.0 with Client tools.
When we are trying to open WebI documents from BI Launch Pad we are getting the following error message.
(Error: RWI 00200) (Error: INF)
Does anyone have any idea what does this mean?
Thanks in advance.

Hello Mark,
Did you ever find the solution? By the way, you should not concern yourself with the AIX system. You should be able to connect with client tools from your local windows PC usng the corresponding DB 32 bit drivers.
I am having the same problem only with webi. Crystal reports work. Issue was not present on BO4-SP2, but getting this issue on BO4-SP4. BO4-SP4 webi worked with other clients; but not on this particular install.
In the past, the issue was fixed by performing a re-install, since there are so many variables that I have seen on this issue. In this case, I've ran out of options that I know to fix the issue. It would be helpful to circumvent a new install.
SAP Notes 1740500
1740500 - Error "Illegal access to the viewer. Please use a valid URL" or "An error occurred while the applet was initializing" when trying to view or edit a Webi Report
SAP Resolution
At this time, the only resolution is to do a complete uninstall of SAP BusinessObjects Business Intelligence 4.0 and re-install.
SAP Note 1741214 addresses the RWI 00200
A different Java article informs of issues with stack tracing being envoke.
Dennis Soriano

KM Collaboration Launch Pad Error

Hi all,
I am working with EP 6.0 .
The portal shows link for Collaboration launch Pad.
Whenever i click on that link, i get following error message.
Exception class: class com.sapportals.wcm.WcmException
Exception message: Cannot get an instance of the presence state service
Pls hekp me solve this problem.
I will really appreciate ur help.

Hello Vinod,
Check this:
https://www.sdn.sap.com/irj/sdn/thread?threadID=177728
Greetings,
Praveen Gudapati
p.s. Points are always welcome for helpful answers

Problems in launch pad

Similar Messages

Maybe you are looking for