Problems opening ports for PS3 and XBOX 360 on WRT160N

i opened all the ports for both system but one system will be lagging while the other will be fast on connection im trying to make both system run on a fast connect is there a step im missing

Which ports you have opened for x-box and ps3..?
Have you done port forwarding or port trigerring..?
Is ps3 and x-box are connected wired or wireless...?
Reduce the MTU sixe to 1364 on the router.Uncheck"Filter Anonymous Internet Requests". Under Wireless tab,click on Advance Wireless Settings tab and Change the Beacon Interval to 75,Fragmentation Threshold to 2304,RTS Threshold to 2304 and Click on Save Settings...
Now,power cycle the entire network and then,try........

Similar Messages

Ps3 and Xbox 360 already asked many times but no solution works

Hi,
first of all I'd like to share with all of you my real disappoint for having bought this Airport Extreme Base Station. I really hope that someone at Apple will read my post and come to my house because I would have just a few words to tell them.
After 4 years of proficuous cooperation my Netgear WI-Fi router left me and I immediately thought to replace it with an Apple product just to be sure that it would have been easy to install and on top of performances.
I chose the Airport Extreme which is much more expensive than quite all the other same product but I didn't care about it because I would have brang home an excellent product.....or...at least I thought it !
Once in my room the soap opera began. I'm not a genius but I consider myself a medium skilled user and, in any case, even it is not my real job, I configured many bigger LANs than my personal ones and I never had such kidn of problem.
I read many posts where people were asking for information because they couldn't connect their Airport Extreme to their PS3 or Xbox 360 but I never had such kind of problem. It really worked immediately and both consoles worked in few moments.
My REAL problem is that both of them are terribly slow and I can't do anything online. I can't see streming videos, I can't play online and I can't neither play videos that are on a LAN DLNA server !!!!! It takes about 35 seconds to play a video and some times it has to stop for empty buffering reason. This is really unacceptable.
I tried so many configurations and nothing changed and I also took a look at some guides but they had been written with old firmwares so they are quite unuseful for me.
After having asked a friend of mine to give me his router (a Netgear ones) for some days I finally made myself sure that the problem is the Airport Extreme.
It also has a very poor signal because my iPhone has difficulties to keep the connection in areas where my old router worked fully.
If only I could turn back time I'd never buy it again but now, having spent to useless my money, could you please let me know a working configuration for the latest firmware 7.4.2 ? I tried to use the previous firmware but I have the same problems.
There is only a wall separating the Airport Extreme from the PS3 and Xbox and both of them get a 100% of signal but I really don't know what to do.
Thanks for all the help you could provide me.
Bye.
Christian

Sorry but I have no way to measure the actual throughput for any of my devices (I have 2 Xboxes which have the same problem and even my iPhone suffer of a bad connection).
In any case I really can't understand why the connection is so bad. I can even get in touch with my ISP to ask them if there is some problem with the connection (maybe a coincidence and the Airport Extreme has nothing to do with it ?????) but the facts remain: even my DLNA server and PS3 connection is slow and I can't clearly see the movies I have in my intenal LAN and also the iPhone show a poor connection to the Airport Extreme and it is because of the Extreme for sure.
I really don't know what to do.

PS3 and XBox 360 problems. NAT issue.

I don't know if anyone is having this issue. I own an XBox 360 and a PS3, both connected wirelessly to my WRT54GS router. If I play the XBox 360 (which requires an open NAT) it's fine. As soon as I download something (not play something) on my PS3, it turns the NAT into Moderate rather than Open. When I again turn on my XBox 360 I have problems with Live. So I must reset my router every time I download content on my PS3.
Does anyone know why this happens or how to keep it from happening again?
Thanks,
Ryan

check out the hardware version on the unit...and then go to www.linksys.com/download and look for the firmware of the appropriate version number of WRT54GS...
access the router interface using http://192.168.1.1 . Logon using the password "admin"..ensure that the router has the same firmware as available on the website...if not , upgrade it first..
after the firmware upgrade , reset the router and reconfigure ...
on the router ui , change the MTU settings to 1364 ...assign static ip add and dns on the x-box and PS3....the ip add should be out of the range of the router's DHCP ( i.e out of 192.168.1.100 to 192.168.1.149 )
on the router ui , go to "Applications and gaming" tab and forward ports 88 and 3074 for the ip add of the x-box and 10070 - 10080 , 6000 - 6999 for the PS3..

Help - WRT400n how do I get better hard wired speeds on PS3 and Xbox 360

I wanted to get better speeds while playing on-line on the PS3. I bought the WRT400n router (I had the WRT54G) and it seems to be working ok. I just hardwired the ps3 and the speeds are a little slower. Wireless I was getting 12.0 Mbps down and 1.0 Mbps up, now wired I am now gettiner 10.0Mbps down and 2.0 Mbps up. I numbers are lower wired, how come? I have a new Cat 5 cable and I just had a direct cable dedicated to the router put in. I thought I was going to see much better speeds. Can anyone help me out? I am very confused about the the speeds. People were telling me when I hardwired I would get get speeds up to 50 to 100. What am I doing wrong?
Thanks..............

On your Router setup page, below change the MTU size to 1365 and below click on Save Settings, then click on the Wireless tab and below change the Wireless Channel to 11 and click on Save Settings, then click on the sub tab under wireless "Advance Wireless Settings" and below Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
Once you are with this settings, then click on the 'Security" tab and below Uncheck "Block Anonymous Internet Request" and click on Save Settings...
Now unplug the power from the Router and Modem,wait for 30sec and then first plug the power to the Modem and once all the lights are solid then plug the power to the Linksys Router. Now you can check the speed on your XBOX.

Opening ports for ichat and gaming...

Hi folks,
When I try to connect to a friend (she's on an Imac) with Ichat or she tries to connect to me (via webcam) we always get the refused error. Also When we try to play Star Wars Battlefront, we can't connect to eachother's computer.
I haven't turned the Tiger Firewall on, so I know the problem is with my Modem, The Speedtouch 530.
I think it has like an internal firewall, so how do I open these ports and what do I need to change in the modem's settings?
I did set the connection type to PPPoe in the Tiger Network setting.
thx.

Hi Tim,
Did your modem come with a manual? There may be some procedures outlined in the manual.
Or google.
http://www.portforward.com/english/routers/port_forwarding/Thomson-Alcatel/Speed Touch530/SpeedTouch530index.htm
This looks like a lot of good help screens for your modem.

Problems opening ports for Torrent downloads

Is there a how to guide or anything out there on how to properly open and forward ports....for something like a Torrent client?
I thought I was doing everything right, but I still can't get my client to connect to any trackers.
This is what I've done so far:
Added a new protocol for bit torrent with the following ports that my client uses:
TCP Any -> 6881-6891 UDP Any -> 6881-6891
Forwarded that protocol to the static IP of the machine running the client on the network.
I thought that's everything it would take to make it work, but no luck. I did the same thing with ftp and http for a filer server I use and it all works great.
Any tips?

You are very close to allowing users to connect to you, because this is my understanding of the status of ports.
#1 A port will be stealthed / time out / filtered if something is blocking that port.
#2 A port will be closed / connection refused if nothing is blocking that port and the server is not listening.
#3 A port will be opened / success if nothing is blocking that port and the server is running.
Here are example(s), of what I mean...
#1 Stealth / time out / filtered
http://i42.tinypic.com/qo8w9j.jpg
#2 Closed / refused
http://i40.tinypic.com/2wp82e9.jpg
#3 Open / success
http://i42.tinypic.com/vdis8o.jpg
-> You need to start the server for the port to be open. -
If need be: It would help to know more about this single NAS box that runs a web server, ftp server and a torrent client.
Like, the brand and model of it..
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Can I use a Time Capsule as a HD for my PS3 or Xbox 360?

Hi guys, I need some help... I'm thinkong buying a TimeCapsule,
but I want to know if I can use it as a external Harddrive for my
PS3 and Xbox 360... (they have less than 12 Gigabytes left)
but I dont want expand their capacity by buying each one a HDD...
thats why I want a time macine and use it as HDD for all my Devices....
please help!

No. A Time Capsule has no media serving logic.

Air port express and Xbox 360

I use the Airport Express as my wireless router. When I first bought it I just used it for Air Tunes to my outside speakers, no problem. Then I was able to get cable internet and used it to connect to my iMac, no problem. Then my wife bought a laptop, connected to the ApE, no problem. Bought a Vizio Bluray, connected to the ApE, no problem. THEN I got an Xbox 360, the newest one out with the built in wifi, big problem. Nothing I can do will connect it to the ApE. I have tried manually setting the IP, subnetmask, SSID with password and nothing. Any thoughts on this??? Yes, I'm trying to play email wars with Microsoft support, but no help yet.

One option would be to enable Internet Sharing on the iMac to share the Internet connection to the XBox's Ethernet port.
To setup for Internet Sharing (Wireless to Wired):
Enable Software Firewall
System Preferences > Sharing > Firewall
o Click Stop to start the software firewall
Setup the Network
Cable Modem > (Ethernet cable) > /[Ethernet port] Wireless Internet Router > (wireless) > /[AirPort Card] iMac /[Ethernet port] > (Ethernet cable) > /[Ethernet port] XBox 360
Setup Port Order
System Preferences > Network > Show > Network Port Configurations
o Verify that "AirPort" and "Built-In Ethernet" are enabled.
o Verify that "AirPort" is at the top of the list, followed by "Built-In Ethernet."
o Click "Apply Now."
Configure the Internet Connection
System Preferences > Network > Show > AirPort > TCP/IP
o Configure IPv4: Using DHCP
o Configure IPv6: Automatically or Off
Enable Internet Sharing
System Preferences > Sharing > Internet
o Share your connection from: AirPort
o To computers using: Built-In Ethernet (checked) (Note: Uncheck all other entries in the list.)
o Click Start

32" LCD HDTV Dynex - will not recognize a PS3 or Xbox 360

I recently bought this TV for $300, I've tried connecting both a PS3 and a 360. Both times the TV refused to recognize the signal from the the HDMI cables. I tried different cables and different ports. Thoughts?

Is your Dynex TV 720p. It sounds like you have your PS3 and 360 set up for 1080p format and your TV is only 720p, I would recheck the settings of your PS3 and 360.

Getting error 'opening port for MGR (Connection refused).

Hi Guys,
I m getting below, while starting replicat on target.
GGSCI (ggtarget) 16> start replicat RLOAD
Sending START request to MANAGER ...
ERROR: opening port for MGR MGR (Connection refused).
GGSCI (ggtarget) 20> view param mgr
PORT 7809
USERID orgg, PASSWORD orgg
PURGEOLDEXTRACTS /ggs/dirdat/*, USECHECKPOINTS
GGSCI (ggtarget) 21> view param rload
REPLICAT RLOAD
USERID orgg, PASSWORD orgg
ASSUMETARGETDEFS
HANDLECOLLISIONS
APPLYNOOPUPDATES
GETUPDATEBEFORES
reperror default, discard
DISCARDFILE ./dirrpt/rload.dsc, purge
MAP HR.TCUSTORD, TARGET HR.TCUSTORD;
MAP HR.TCUSTMER, TARGET HR.TCUSTMER;
from Source I could able to do the telnet to target...
What could be issue ???

Hi,
Error:
GGSCI (ggtarget) 16> start replicat RLOAD
Sending START request to MANAGER ...
ERROR: opening port for MGR MGR (Connection refused).
You can start Manager, but when you try to start Replicat, GGSCI gives me a connection timeout error
Solution:
GoldenGate uses a TCP/IP socket to communicate between local processes. When you issue a START, STOP, SEND, or other command in GGSCI, the command interface will try to open a local port for the process.
Here is how to find out which local ports these processes are listening on. In the dirpcs directory, there will be one file for each running GoldenGate process.
For Manager, the file name will be MGR.pcm.
For Extract, it will be <GROUP_NAME>.pce.
For Replicat, it will be <GROUP_NAME>.pcr.
These are text files that can be viewed by using cat or any equivalent command. For example, the MGR.cpm file content will read like this:
PROGRAM MGR PROCESSID MGR PORT sys1.4356 PID 60070
After the keyword PORT will be the local hostname and the port number that Manager is supposed to be running on. In the preceding example, the hostname is sys1, and the port is 4356.
The program (ggsci) tries to use that hostname to communicate to the process (Extract/Replicat/Manager) when the command is issued in GGSCI. If you get a timeout or connection-refused error on the command, that means GoldenGate could not connect to the local host. Most of the time, you should have no problem connecting to a local host, but when you have the wrong IP address or routine table configured in your TCP/IP settings, connection errors can happen.
To troubleshoot this, follow the steps below
1. Try to ping that host name from the OS shell to see if it goes to the correct IP address (which should be the one for the local system).
2. If the ping is successful, try to telnet to the Manager port on your local host. You will be able to see your telnet session connect if a Manager is listening on that port.
Here is an example:
shell>telnet
telnet> open sys1 4356
Trying 100.100.100.100...
Connected to sys1.oracle.com (100.100.100.100).
Escape character is '^]'.
3. If your telnet session times out or gets a connection-refused error, that means either the hostname is wrong or the port number is wrong.
If the ping to the hostname listed in the pcm/pce/pcr file fails, or if you cannot connect your telnet session to the port listed in the file(s), contact your network engineers to get the TCP/IP issue resolved.
Hope this information helps.
Thanks & Regards
Santhosh

How to forward/open ports for WRT54G?

Hi. I recently bought a WRT54G because my old router was destroyed by lightening and thunder. I have managed to set it up, and got the interent itself to work with static IP adress (192.168.1.101 for my PC).
However, even though I have tried to forward/open ports for applications like uTorrent and DC++ as well as Limewire, I have no luck. When I test if the ports are indeed opened, I get the result that they are not. Here are how my port forward setting looks like for utorrent. The port in the settings image is of course the same as in uTorrent.
http://www.pictub.com/quickupload/01/untitled-1mb4wd.jpg
I can't seem to open any ports, even though I have followed tutorials like the ones at portforward.com. I have the latest firmware for my router, as I flashed it when I got it. Help .

Yes, I did .
Anyways, look what I found in the uTorrent FAQ:
1.7 Special note for users with Linksys WRT54G/GL/GS routers, there are severe problems with them when running any P2P application
To fix it, they say one has to flash with a unofficial firmware, but I will rather get the money back and buy another router tomorrow. Thanks for the help anyways .

Open ports for all in LAN

Hi, a few days ago I bought a wireless router WRT160n. I want to ask how to open some port for all in LAN(3 clients). For example all in LAN have PeerToPeer application for torrents. I want to open port for example 20202 for all. Now I open port from menu Applications & Gaming->Single Port Forwarding, but I must set port for each user IP address.
Can somebody tell me how to open port for all in LAN without to config for each computer?
Thanks in advance.

Hi gv. I read more about UPnP and the WRT160n User Guide. In section Administration>managment int wrote that UPnP is Enabled by default in my router it is corect. I Setup mu PeerToPeer(eMule) TCP/UDP ports to 20202 and check option "Use UPnP to setup ports". I test and close this port on my router configuration for my computer on "Single Port Forwarding", but in eMule the port is still block. Can you explain why it did not work. For UPnP it says that if Enable it allow users with Windows ME and XP automatically to gonfigure Router ports
Thanks in advance!
Best Regards.

Do I need to open ports for NTP?

I just noticed that my hwclock was off by nearly 30 seconds. It's almost certainly due to the recent initscripts update.
As I was looking into resetting the clock, I found out that openntpd is deprecated so I've switched to ntp, configured the daemon, reset the time with ntpd -q, and started the daemon. The time is not accurate again.
I remember back when I first installed Arch I tried to set up ntp but it didn't seem to work, so I tried openntpd and stuck with that. I reached the conclusion that ntp required open ports, which I felt was unnecessary given that openntpd could do the same thing without open ports.
Now that I'm looking at it again, I can't find any definitive answer...
Do I need to open ports for ntp if I only want to sync the system that it's running on?

ISC ntpd (the ntp package) will open UDP 123 on all your interfaces regardless of what you do with it. It will work anyway even if you block this port in iptables, assuming that you're allowing responses to established traffic as usual - your outbound mobilization requests to your chosen servers will be enough to allow the responses, and the same with further traffic sent for the lifetime of ntpd. Using iptables like this is probably the easiest way to secure ntpd.
There's also some defense in depth you can do:
- run ntpd as non-root
- run it chrooted to some safe directory (really only makes sense when doing non-root as well, since root can break out of a chroot)
- apply ntpd's built-in access controls (see examples in ntpd.conf, and full docs in ntp_acc(5))
I accomplish the first two of these by chowning /var/lib/ntp (and any contents) to ntp:ntp (so ntpd can write ntp.drift there when non-root), by using a driftfile path relative to the chroot in ntp.conf, and by setting NTPD_ARGS="-g -i /var/lib/ntp -u ntp:ntp" in /etc/conf.d/ntp-client.conf.
For the third, I chose to not allow any remote traffic to initiate anything with my ntpd, with this /etc/ntp.conf:
server ac-ntp0.net.cmu.edu iburst
server ac-ntp1.net.cmu.edu iburst
server ac-ntp2.net.cmu.edu iburst
server ac-ntp3.net.cmu.edu iburst
server ac-ntp4.net.cmu.edu iburst
restrict default nomodify nopeer noquery
restrict 127.0.0.1
driftfile /ntp.drift
Note the two "restrict" lines. The first shuts out remote access of most kinds, and the second allows the local machine all the access that would also be denied to it as well otherwise by the first rule. Note also the driftfile path, relative to the chroot of /var/lib/ntp/.
With all these security features, ISC ntpd can be just as safe as openntpd.
The use of the "iburst" keyword on the server lines to recover more quickly from out-of-contact conditions is also quite nice, and not rude to the remotes like "burst" would be.
One of the nicest other features of ISC ntpd is that it's smart enough to notice when network state changes occur, like bringing a VPN up/down, changing routes, or switching from wired to wireless and back. openntpd tended to just lose connections in these cases.

Do I need to open ports for my services if I am connecting through VPN

Hi,
I work in a small office and we are trying to connect people remotely to our server through VPN.
Using the Server App I managed to make VPN work and successfully connected to our file share points, so that means file sharing worked without opening ports for afp on my Airport router.
On the other side I cant connect to other services as iCal and Address Book as I am locally in the office. Does that mean I have to open the ports for those services on the router, if yes then why use VPN in the first place.
Thanks,

If I understood you correctly:
External client -> (server.domain.name) -> Router -> Server: is working
Internal client -> (server.domain.name) -> Router -> Server: is not working
Internal client -> (local ip) -> Server: is working
If yes, you can implement a-la "split zone DNS".
1. On the external DNS your domain name server.domain.name resolved to the external router IP.
2. You should add record (and zone) server.domain.name to your OS X Lion Server DNS pointing to local IP
When you are connected to VPN, system sets DNS server to your Lion server and server.domain.name is resolving to local IP.
When you are working without VPN, system use external DNS and server.domain.name is resolving to external IP.
Of course, you should open ports for your services on the router is you want to use them from external network.
I am using this configuration and it works perfectly.

Do i need to open port for crash plan online backup service

do i need to open port for crash plan online backup service?
Thanks!

Possibly. I would start by checking out this CrashPlan support article. CrashPlan does require certain ports on both your computer's and network router's firewall to be open in order to communicate properly.

Problems opening ports for PS3 and XBOX 360 on WRT160N

Similar Messages

Maybe you are looking for