Problems performing CiscoWorks LMS 3.1

Hello,
I had previous problems running Daemon Manager, I fixed up that problem already but now the problem is that whenever i want to configure anything within any module, then it shows errors about communication with DCR server or other engines and in some cases it says i have to run the license server.
I looked over the license server log and shows an error "Unable to launch JVM".
I also revised my services and all of them appear as started.
Any suugestions???

I configured the services as you requested and after that restarted the server tried to open the LMS portal but it shows "the page cannot be dispalyed" so revised services window page and noticed that the following services are down:
CiscoWorks ANI database engine
CiscoWorks RME NG database engine
CiscoWorks Web Server
CWAWFEngine database engine
CWCS Cmf database engine
DFM dfmEpm database engine
DFM dfmInv database engine
DFM dfmFh database engine
OpxXMLRuntime
only CiscoWorks Tomcat Servlet engine appears as started...
aren't services supposed to start "automatically" eventhough they're set up as manual???

Similar Messages

  • Problem Authentcation CiscoWorks LMS 4.1 with ACS 5.3

    Dear
    i have a problem authenticating cisco LMS user through ACS 5 whenever tries  to run a DCR Job  verification it fails to telnet , however it used to work with the pervious ACS 4 but after upgrade , it seems to be a problem , and when i tries to login with this specific user with third party terminal it works fine.
    here is logg in the ACS monitor
    Failure Reason > Authentication Failure Code Lookup
    Failure Reason :
    13031 TACACS+ authentication request missing user Password
    Generated on:March 12, 2013 7:09:37 PM AST
    Description
    The TACACS+ authentication request did not provide a user Password
    Resolution Steps
    The  device is sending a TACACS+ authentication request that is missing  information needed by ACS. Check the device to verify that it is working  properly and has up-to-date software

    I'm running the latest version of both, and it's running fine for me.  You may have to change your TacacsPromts.ini file to include the right prompts.  I think it's:
    [TELNET]
    USERNAME_PROMPT=
    PASSWORD_PROMPT=
    You'll have to put in your own prompts, though.   Whatever your prompts are, is what goes afterward.
    If my prompt is Myspecialprompt: and pass is Myspecialpassword:, I'd use
    [TELNET]
    USERNAME_PROMPT=Myspecialprompt:
    PASSWORD_PROMPT=Myspecialpassword:
    If you have more devices with different prompts, just use a comma after the colon.  Btw, you don't need the credentials in there, just the custom prompts.

  • Problems with CiscoWorks LMS 4.0

    Dear Technical Support Staff,
    We encounter some problems with the application Cisco Works LMS 4.0 , installed in OS Windows Server 2008R2 64 bit  Standart Edition with the usage of a patch CiscoWorks_LMS_4.0.x_WIN2K8_R2.
    A brief explanation of our network - it consists of VTP domain of the 3rd version, in the layer of the core 
    2x6509 whish are being operated in VSS (all the configuration is based on them : Vlans, routing, acl list), in the access layer the switches 3750 (some of them are operated in the stack), DNS server is absent, to register the devices in the application we put the title of the device into the host file of the server.
    Screenshots are added to the list of problems.
    1. IP addresses of the end hosts in the section User tracking are not displayed, in the site cisco.com there is a manual on solving the given problem for the other OSes.
    2. Switches 3750 in the section Ciscoview are not displayed, however in the section device update in the list of the installed packages those devices are present, also it is impossible to set (update) the package cisco view for the required device. We have downloaded those packages individually but in the process of installing them locally or from   Cisco.com, the application displays an error.
    3. It is necessary to see loading of the interface (channel) in the current moment since as far as I remember it is possible to do through MiniRmon, having preliminary setting of all the required interfaces, but I can't set them and the application displays an error. Maybe I am wrong somewhere please correct me if necessary.
    4. Where can I find a full description of the Faults.
    5. Not from all the devices collections of configurations take place though settings of Telnet and the name Community are everywhere the same.
    6. In the section Topology in the scheme of the network those changes do not happen at once? for instance if some device is switched off so in the scheme it does not get red immediately and the same situation with the opposite when the device is available and being pinged so it does not get green. Is it possible to set it the way so the changes occur simultaneously? The messages on failures come in time how can I set it?
    Regards,
    Alexey Sokolov

    Dmirty, try to do a
    net stop crmdmgtd
    net start crmdmgtd
    This normally resolves the issue for me
    Did you restart the daemon manager for a device package update?
    I have see this a number of times
    Cheers,
    Michel

  • CiscoWorks LMS cannot add PIX/ASA in software repository

    Hi,
    I can see that LMS in RME Software Management cannot add PIX/ASA software saying not supported.
    Any configuration issues.
    I have got another problem. CiscoWorks LMS need to download IOS on cisco router, the process fails in RME Software Mgt. But the LMS is nated when it goes through the router.
    i guess the script does not know the natted ip when running it on the router. If there is a way that I can specify the natted IP of the LMS. Fortunately, it is a nated static IP.
    Thanks,
    Ashley

    Hi Joseph,
    It is working fine. My mistake, issue with TFTP source interface.
    However, I had got a small issue.
    I have got a cisco router which RME accesses with ip natted ip, which you have indicated and It is working fine with RME. RME can manage the router perfectly.
    However, DFM is leaving this router in questioned mode. So, the SNMP Credentials must be ok since it is good with RME.
    Do I have to specify the Natted DFM ip as well for this router? Or something else must be done.

  • CiscoWorks LMS 4.0 Time Zone Problem

    Hi,
    CiscoWorks LMS 4.0 timezone is VET. I know that LMS time is syncronized with system time. Hovewer, system time is correct but LMS's time is wrong.
    -I restarted LMS CW Deamon Manager
    -I re-installed LMS
    My problem still exists.
    What should I do to syncronize the time?
    Thank you for your help.

    My setup files were corrupted. I tried new setup and LMS succesfully installed.

  • CiscoWorks LMS problem

    We are running CISCOWORKS LMS in our Data Network,
    But right now getting below problem,
    1.    Unable to integrate Cisco-3925 integrated service router
    2.    Unable to integrate Cisco-2811 integrated service router
    3.    LMS cannot sense link status
    4.    LMS cannot auto discover link
    Attached Image for your kind reference.Appreciate your concern about this issue.

    Hi Hafiz,
    Kindly let me know how you are adding device to CiscoWorks LMS 2.6.
    As a best practise, when you will add new device to CiscoWorks, you should not select the device type while adding the device to CiscoWorks. Let the ciscoworks collect the inventorty on device and identify it automatically.
    To start with make sure you have the lastet MDF device packages install for Common Services and then install all device pachages for other components like RME, CiscoView etc but make sure to have lastest MDF install first.
    Thanks
    Gaganjeet

  • Problems after upgrading LMS from 4.1 to 4.2.3

    After the upgrade of the LMS we have the situation that all our deviced are visible in the subnet groups but not in "all devices".
    When I want to launch an inventory collection the following message is displayed:
    "ICSU0025: Problem with JRM. The JRM server may not be running. Check ICServerUI.log for more details. See the user guide Administration of CiscoWorks LMS for the log file location."
    When I do a Discovery, the deviced are being discovered but they are unreachable.
    And all the host names are changed into their IP addresses.
    I can't seem to find the problem. Even after roaming the forum here.
    I'm not able to pinpoint the exact cause of the problems...
    Any ideas?
    regards,
    W

    That is a healthy normal state for ANIServer. I checked some similar cases and it seems most of them were transient and got resolved once daemon was reatarted.
    I would suggest to follow this procedure once additionally :
    > Stop Daemon manager
    > Regenerate SSL certificate
    > Do a transaction log for RME DB
    > Start the daemon
    For 2nd and 3rd check my this post for process :
    https://supportforums.cisco.com/message/3597059#3597059
    If this is Solaris/linux, for transaction log, check this link (under Recovering From a Server Crash).
    -Thanks

  • User tracking not finding any hosts in Ciscoworks LMS 3.1

    L.S.
    Our test-configuration is as follows:
    Application versions:
    Ciscoworks LMS 3.1
    Ciscoworks Common Services 3.2.0
    Campus Manager 5.1.4
    We have 31 managed devices in Campus Manager (data has been collected on all),
    Edit: All of them show up green in the topology window.
    The device are: 2 6509 cores (running IOS s72033_rp-IPSERVICESK9_WAN-M version 12.2(18)SXF8), 1 ASA firewall (running ASA-OS version 8.0.5) and 29 switches (2960 and 3560 models both running ios version 12.2(52)SE). The switches are connected as follows:
    User tracking jobs are running normally, but aren't finding any end-hosts or IP phones at all (I suspect around 250-500 hosts+ on these switches)
    We are running SNMP v3 on the switches and have added the following configuration items to all the switches:
    snmp-server group readonly v3 auth context vlan-1
    <repeat for all present snmp-contexts as shown in show snmp context output>
    snmp-server group readonly v3 auth context vlan-83
    Debugging is enabled in CM->Admin->Debugging Options->User Tracking Server
    This is the UT.log file of the last major acquisition:
    messages will remian logged to file: D:\PROGRA~1\CSCOpx\log\ut.log
    2010/01/13 14:00:01 main MESSAGE ProcessInitializer: Properties will be read from D:\PROGRA~1\CSCOpx\campus\etc\cwsi\ut.properties
    I= 0value *.*.*.*
    I= 1value 6
    I= 2value 1
    2010/01/13 14:00:01 main MESSAGE DBConnection: Created new Database connection [hashCode = 10969598]
    PartialOrderNode tree dump: time base = VMPSMajor
    <root>
        VMPSMajor: <root>
        VMPSMajor:     VMPSMajor.GetXMLData
        VMPSMajor:         VMPSMajor.PingSweep
        VMPSMajor:         VMPSMajor.PopulateFromDCR
        VMPSMajor:             VMPSMajor.GetPortStatus
        VMPSMajor:                 VMPSMajor.GetBridgeTable
        VMPSMajor:             VMPSMajor.Sweep
        VMPSMajor:                 VMPSMajor.GetIpXlateTable
        VMPSMajor:                 VMPSMajor.GetIpv6XlateTable
        VMPSMajor:                     VMPSMajor.GenerateTable6
        VMPSMajor:                         VMPSMajor.GenerateTable
    SMFunction evaluation order: time base = VMPSMajor
      VMPSMajor.GetXMLData  Major
      VMPSMajor.PingSweep  Minor
      VMPSMajor.PopulateFromDCR  Major
      VMPSMajor.GetPortStatus  Minor
      VMPSMajor.Sweep  Major
      VMPSMajor.GetBridgeTable  Minor
      VMPSMajor.GetIpXlateTable  Minor
      VMPSMajor.GetIpv6XlateTable  Minor
      VMPSMajor.GenerateTable6  Major
      VMPSMajor.GenerateTable  Major
    Time base VMPSMajor has 5 major nodes and 3 minor traversals.
    log4j:ERROR No appenders could be found for category (CTM.common).
    log4j:ERROR Please initialize the log4j system properly.
    In classlist loader
    In classlist loader processing sub classes
    updation done
    In classlist loader completed
    2010/01/13 14:00:03 main MESSAGE DBConnection: Created new Database connection [hashCode = 12524859]
    Calling default
    Subnet to SubnetData Map Size :73
    2010/01/13 14:01:31 DBConnecton-Reaper MESSAGE DBConnection: Closed Database connection [hashCode = 12524859]
    2010/01/13 14:01:31 DBConnecton-Reaper MESSAGE DBConnection: Closed Database connection [hashCode = 10969598]
    2010/01/13 14:04:50 main MESSAGE DCRDevWrapper: Closing DCRProxy
    I'm slowly getting to a dead end here. What am I missing?

    Well, our problem was resolved finally through a weird coincendence after having a websession with a Cisco TAC engineer (TAC case SR 613376661)
    We changed the
    snmp-server group readonly v3 auth context vlan-xxxx
    commands in the switches to:
    snmp-server group writeonly v3 auth context vlan-xxxx
    that is: use the writestring in the snmp-server groups instead of the read string.
    After we changed that, all of the User Tracking mysteriously started working.
    As far as I know, the writestring should not be needed, but apparently it is....
    Is there any explanation for this?

  • CiscoWorks LMS 4.0 No muestra los dispositivos

    Buenas.
    Tengo el CiscoWorks LMS 4.0, y de un momento a otro me dejo de mostrar los dispositivos que me habia reconocido, hice de todo y nada, por ultimo desinstale e instale nuevamente y lo mismo, me reconoce los dispositivos pero no me los muestra.
    Quien me puede guiar para saber que problema estoy experimentando.
    Gracias.
    Jose Luis Diaz Ortega
    Ingeniero de Sistemas.
    Administrador de redes.       

    Gracias.
    Si antes me mostraba en el inventario todo los dispositivos y en la opcion de monitor igualmente, pero cuando trataba de hacer una modificacion en la parte de configuracion no me desplegaba los dispositivo. Como tenia este problema lo que hice fue instalar nuevamente la aplicaciones, hice en descubrimiento me reconoce los dispositivo pero ahora no me muestra nada en inventario al igual que en la opcion de monitor.
    Siempre he trabajado con la verison LMS 4.
    opcion de inventario
    opcion de monitor
    En la imagen siguiente son los dispositivos que fueron reultado del descubrimiento realizado, esto sigmifica que los encuentra pero no me muestra informacion en la opcion de inventario y monitor.
    Jose Luis Diaz Ortega
    Ingeniero de Sistemas.
    Administrador de redes.

  • CiscoWorks LMS 4.0.1 - Could not generate the report

    Hello,
    I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
    I tried the same procedure with 2 other switches but I have got the same result.
    Does anybody has an idea of how I can fix this issue?
    Thanks a lot in advanced.
    Best regards,
    Marc Hoffmann

    Hi Marc,
    I have this problem too. I rebooted my Windows but no solved. You known the service name responsible for this error? You have any other sugestion?
    Thank you !!!

  • Ciscoworks LMS 3.2 Processes down

    Hello all,
    I have installed ciscoworks lms 3.2 on windows 2003.
    The discovery ran successfully and the devices were added to dcr.
    After a few days, the ciscoworks processes were automatically down.
    “Processes NOSServer, CmfDbMonitor, FHServer, IPMProcess, Sysloganalyser, 1041, CTMJrmServer,
    Interactor1, EDS-GCF, IPMOGSServer, CMFOGSServer, 1015, DFMOGSServer, UPMDbMonitor, ChangeAudit, Inventory Collector, CampusOGSServer, Interactor, TISServer, jrm, UTManager,
    ConfigMgmtServer, DCRServer, PMCOGSServer, ICServer, EssentialsDM, InventoryCollector1, PTMServer, RMEOGSServer, UPMProcess are down” .
    Why were the processes down?
    What might be the solution?
    Thanks and Regards
    Yama

    Hello,
    Thanks for your answer.
    Unfortunately the problem still exists.
    I attached the required files.
    Thanks and Regards

  • Ciscoworks LMS 3.2 bug summary report

    Hi,
    I have one Ciscoworks LMS 3.2, it managed around 500 devices. I tried to generate bug summary report and the bug number is zero. Please kindly help to solve this problem.
    Best Regards,
    Jackson Ku                  

    For how many devices are you running the report?
    [ Wed Jan 05  21:26:50 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.bugtool.BTBugSummary,populateResults,295,Cisco.com URL Connection TimeOut: Try again later or with less number of devices.
    Have you tried running it for just one?
    This is also kind of strange,
    [ Wed Jan 05  21:26:50 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.bugtool.BTBugSummary,formBTDevHash,228,Device(s) are not supported by Cisco.com.
    [ Wed Jan 05  21:26:50 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.bugtool.BTBugSummary,formBTDevHash,229,Hence Could not generate report
    Like as if cisco.com would not know about these C3750's
    Maybe do an export of these 3750's in the DCR to see if the all have the same OID and if it is a supported OID.
    Are your device packages up to date? You may want to sync those with CCO.
    Cheers,
    Michel

  • CiscoWorks LMS: not receveing certain SNMP traps

    CiscoWorks LMS 4.0.1 (I know it's old and unsupported).
    Problem: not receiving certain SNMP traps.
    For example: I receive trap like "STP new root" but not like "port put to err-disabled" or my custom traps (produced by EEM scripts).
    I've investigated my situation and found out that switch sends traps and they reach* LMS but somehow LMS ignores them (there's no trace of them in GUI). I've read that some traps just pass through LMS but my traps are very important and I need to know about them.
    * I did Wireshark capture on LMS machine.
    I'd like to know how to debug receiving of SNMP traps in LMS:
    which specific debugs need to be enabled,
    which specific log files need to be examined.

    LMS uses DFM to process certain traps.
    All traps it deems unimportant are dropped.
    If you want to use the LMS GUI you can have you device send a SYSLOG message rather than a trap.
    use logging source command to make the management interface send the message.
    Then there is a GUI that allows you to launch an action on a message
    Cheers,
    Michel

  • Installing Ciscoworks LMS 4.0 on Windows domain member server.

    Hello.
    I'm looking for some suggestions about installing CiscoWorks LMS 4.0, and upgrade, on a domain member server running Windows 2008 R2 SE 64 bit.
    Thanks.
    Andrea

    Here are the basic install best practices:
    1) Install as a local administrator (this means create a local account and add it
    the "Administrators" group).
    2) My Computer -> Properties -> Advanced -> Environment Variables
    Set the USER TMP and TEMP to a shorten path like
    C:\Windows\temp
    3) Make sure you have FIXED pagefile size like 8182
    My Computer -> Properties -> Advanced -> Performance Options -> Advanced
    4) May need to reboot, certainly log out an back in to make sure step 2 applies.
    5) Stop all anti-virus and firewall during the installation.  Disable them in services and reboot if necessary.
    *  NOTES: Anti-virus can be re-enabled after installation, but you should  EXCLUDE
    the NMSROOT directory as long as LMS is installed on the  server. DEP should
    remain off (that is, set to only protect critical  Windows system files) as long as LMS
    is installed on the server.
    *  If Internet Information Services (IIS) is detected on your system and  if you have
    continued the installation with IIS services, you cannot use  the port number 443 for
    HTTPS. Instead, you must use the port numbers  ranging from 1026 to 65535 for
    HTTPS to avoid this conflict.
    When performing the installation, make sure these two steps are followed:
    *  Install from original, locally attached media
    *  NEVER abort the installation after the installer says not to
    It may not always be possible to install from original, locally attached  media
    (especially on VMs). But you should avoid from installing over  the network as hiccups
    can cause bad installations. If you are  installing on a virtual machine, convert the DVD
    to an ISO image, then  mount that within the VM.
    Here is the document detailing all ports needed to be allowed (excluded from policy)
    for LMS 4.0
    LMS 4.0 Port Usage
    General Notes:
    If you want to upgrade the operating system from Windows 2003 or Windows
    2008 to Windows 2008 R2, you must first complete upgrading the operating
    system, and then install the LMS 4.0.x Windows 2008 R2 patch.
    *  You can install the LMS 4.0.x Windows 2008 R2 patch only on LMS 4.0.x
    and not on the lower version of LMS.
    *  You cannot install Integration Utility and HP Open View 7.x or 8.x on
    Windows 2008 or Windows 2008 R2 servers.
    Check out:
    System and Browser Requirements for Server and Client
    LMS Patches-Windows

  • CiscoWorks LMS not sending mail

    Hi,
    I have CiscoWorks LMS functionning properly. For some time, I am seeing problems with it sending mail notifications. When it is rebooted, it sends the mail properly but after some time, the mail notifications are not sent.
    Is there a log file to see the issue with the mail sending? I am not sure whether it is a CiscoWorks LMS issue or the mail server (on which i have no access) to try to isolate the problem.
    The last change that I made to the server, that might be a possible cause. I had installed the HP NIC teaming with 2 NIC cards teamed and assuming the IP address of the server.
    I just want to check with the server before proceding to mail server blacklisting or other.
    Thanks in Advance,
    Ashley

    Sorry,
    Hi,
    I have CiscoWorks LMS functionning properly. For some time, I am seeing problems with it is not sending mail notifications. When it is rebooted, it sends the mail properly but after some time, the mail notifications are not sent.
    Is there a log file to see the issue with the mail sending? I am not sure whether it is a CiscoWorks LMS issue or the mail server (on which i have no access) to try to isolate the problem.
    The last change that I made to the server, that might be a possible cause. I had installed the HP NIC teaming with 2 NIC cards teamed and assuming the IP address of the server.
    I just want to check with the server before proceding to mail server blacklisting or other.
    Thanks in Advance,
    Ashley

Maybe you are looking for