Problems setting up Verizon DSL (DHCP) and AirPort Extreme

I have Verizon DSL with DHCP and old router (Linksys WRT54G). I've bought iMac and new router (AirPort Extreme) to connect to iMac wirelessly. I have a Windows computer connected to the Linksys WRT54G. Now here is the story. I can connect verizon DSL modem (it's in bridge mode) to PC directly and connect to the Internet. When I plug AirPort between the DSL modem and PC, auto-configuration doesn't work, AirPort utility says there is problem with internet connection. Router simply can't obtain IP address from verizon's DHCP server. I've tried to copy DNS server addressed from the IP configuration in Windows, the AirPort light went green and Windows indicated connection as successful, however I still cound't browse the Internet because gateway is not set. Any ideas how to make AirPort connect to the internet using DHCP instead of manual settings? I can try to do it from the mac if needed, I don't think it would make any difference though.

Welcome to the discussions!
Sorry, I can't quite track exactly what you are trying to do.
What would the network that you are trying to set up look like?
Modem>AirPort Extreme>Computers? Are you saying that you won't be using the Linksys in the new setup?
Sounds like you need to set the Airport Extreme up to supply PPPoE service (which the Linksys is doing now-if the modem is in bridge mode), but I will wait for your response before offering specific info.
If you've been fiddling with settings, we may need to do a hard-reset on the AX to start over. You should not be fiddling with DNS, etc. Almost always, these settings are done automatically when you have the device set up correctly.

Similar Messages

Power backup for dsl modem and Airport Extreme

Does anyone here have backup power for a dsl modem and Airport Extreme that is successful? I have a name brand power backup and when the power goes off both the dsl modem and Airport Extreme remain on; however, the network connection is lost so the fact that they remain on doesn't help. I have been unable to find anything about this problem on the internet generally and consultation with a well-known squad person has not helped. Any thoughts about this will be welcome.

Yes, I agree. But since the backup power keeps the modem powered, why doesn't the dsl connection continue? The squad person I talked with told me that the speed with which the backup power units replace power during an outage is about the same across different backup brands/units (I don't recall the speed but it was in milliseconds) and should be quick enough to retain the dsl connection. Doesn't happen.

BellSouth Alcatel DSL Modem and Airport Extreme

I have a new iMac, and BellSouth DSL Internet service (alcatel modem). I get an Internet connection when connecting the modem directly to iMac using an ethernet cable. However, when I try to configure my Airport Extreme 1 of 2 things happens: a constantly blinking amber light, or a green light. In neither instance does Airport Utility see Airport Extreme (even when the light is green). I have tried powering off and recycling both Airport Extreme and the modem, with neither solving the problem. Any thoughts?

The modem is a Speed Touch Home.
wow, I used one of those 8 years ago I did not know they still being used. If I remember correctly it did not have integrated pppoe or pptp client so it requires you to run a pppoe or pptp client on your mac. Therefore when connecting it to an apple airport basestation you have to configure the pppoe client in the base station.
so open your airport utility select your base station , choose manual setup
the click the 'internet' icon in the toolbar of the airport utility window and from the connect using drop down choose PPPoE, then configure it with your isp login details. The click the update button.

Verizon DSL and Airport Extreme

I'm going to add aniBook (oe whatever Apple will call it by then) this spring, as I want to enjoy the wi fi fun like evryone else. My ISP is Verizon DSL, and I was wondering if anyone else here in the discussion board is currently using an Ibook with Verzion DSL and Airport Extreme. I think Verizon has a modem that supports both wired and wireless networking--which is what I'll need since I won't be retiring my iMac G5 anytime soon. So any adive or info would be appreciated.

I currently have the ActionTech Modem (supplied by Verizon) as my wireless router, but would like to replace that with my Airport Extreme. Can this be done?
You will need both. Since both supply NAT, DHCP services and WiFi Access Point, you will have to turn off all three of those in one of them. This is usually called putting the device in "bridge" mode. My recommendation is to turn off those features on the Actiontech modem/router/access point, turning it into a plain DSL modem, and let the AEBSn do all the 3 features (NAT, DHCP, AP).

How-To Set Up with Uverse Gateway with Airport Extreme

I just spent hours figuring this out so I thought it would be helpful to someone. Maybe, maybe not. My goal was to get Back to My Mac turned on...but this should also be how you set up your wireless network if you have both an Airport Extreme and a Uverse Gateway.
As I was trying to setup BTMM, I got a "double NAT" error. To use BTMM, you have to use either Time Capsule or Airport Extreme, so that NAT has to be enabled. That meant I had to figure out how to turn off U-verse's. I looked through the settings but saw nothing about it. Several hours of research--and a useless support call to AT&T--I finally figured it out. Here's the configuration you need, in brief.
On the Airport Extreme, under Internet > Internet Connections, Connection Sharing must be set to "Share a public IP address". Then under the NAT button, Enable NAT Port Mapping Protocol must be checked.
Now, unless you doe rest of this configuration, you will get a double DHCP error. So, in the Uverse Gateway settings, you must do this:
1. Under Wireless, click the option to DISABLE wireless. Click Save.
2. Under Firewall, click the option with DMZ in the name. On this page, choose your Airport Extreme (whatever you named it). Then scroll down and choose the option that says "Allow All Applications (DMZPlus Mode)". Save that configuration. DO A HARD RESET ON THE AIRPORT EXTREME. Then that should enable a single NAT protocol and BTMM will be on its way. And your wireless network will be set up properly.

Will the above method work on a set up with a Verizon Modem to a DLink wireless router to a Time Capsule?
I know of no reason why it would not. Whenever there is another router ahead of the Time Capsule, the Time Capsule must be configured in Briddge Mode. My network has 4 routers. The "main" router is setup to handle DHCP and NAT and the other 3 routers are setup in Bridge Mode. No problems.
Weird thing is Air Video set up tells me I have a double NAT
Double NAT occurs when you have two routers on a network both set up to handle DHCP and NAT services. Your Verizon "modem" may be a gateway....a combination modem/router on the same chassis. If that's the case, then every other router on the network must be confgured as a "Bridge".
If you have the "main" router on the network setup to handle DHCP and NAT, in theory, you can have multiple other routers on the network as long as they are all setup in Bridge Mode. In Bridge Mode, DHCP and NAT are turned off, so the other routers simply pass through the network information from the main router. It's by far the easiest way to configure multiple routers without having to go into special DMZ, port mapping, etc type of configurations.

Setting up wireless network with 2x airport extreme ac

I've got a business customer with 2 new Airport Extreme 802.11 AC behind a comcast modem.
When the first extreme is set up, all is well.
When the 2nd Extreme is introduced, Airport Utility asks to automatically wirelessly extend the network, which I allow it to do.
But sometime during that setup, the 2nd extreme becomes unresponsive, and the connection to the internet becomes broken.
The only thing that restores it is to reboot the first Extreme. No matter how many times Iv'e done this, it results in the same problem. I've replaced Extreme #2 with a new one, and I get the same problem.
There are 20 some odd devices on the network; with one Extreme, it works great, and the Extreme AC's replaced 2 older version of Extreme's that were doing this just perfectly.
What is causing this problem, other than me doing something stupid, and how do I extend the network? I'd rather extend it with the wire it's connected to than wirelessly.

Power off AirPort Extreme 2 for now and test the Ethernet cable that is connected from one of the LAN <-> ports on Extreme 1 by temporarily connecting the cable to the Ethernet port on a laptop or desktop. Turn off the wireless off on the computer and see if you can get a good Internet connection that way.
If you can, then you know that the Ethernet port on the AirPort and the cable are both working correctly.
If you can't, then you need to do some troubleshooting to identify the real problem before you can attempt to configure AirPort Extreme 2.
Post back when you have verified that you have a working connection between AirPort Extreme 1 and the device that you are using to test.

Extending a network with Time Capsule and AirPort Extreme (via Belkin powerline)

Hello -
I've seen many topics about extending wireless networks here, but none seems to resolve the issue I'm having. I currently have a setup where a DSL cable modem is connected to a Time Capsule and I need to extend this network to another room using an AirPort Extreme.
I live in a very old apartment in Brazil and the walls seem to block the signal from one room to another, hence the need to extend it. Since wireless signal is very weak between rooms, I bought a Belkin powerline AV500 so I could connect both Time Capsule and AirPort using the electrical power at home (just installing a regular Ethernet cable between rooms is not an option).
I started with the basics: configure the Time Capsule + DSL as a standalone network, and it works perfectly within it's range. Then I connected the Belking powerline, plugged a MacBook via Ethernet on the other end and still got very good results (actually better speed than expected). Used it for a while with streaming and other network intensive tasks to make sure it could sustain the connection.
Finally, pluggned the AirPort Extreme on the Belking powerline and this is where the problems started. AirPort Utility 6.3.1 only gives me the option of extending a network wirelessly - it doesn't seem to give me the option of extending it via Etherenet (roaming), which is not good in my case. Luckly I had a copy of AirPort Utility 5.6 which seems to do the job (or I thought so), but it's still not working well.
Although I managed to configure both with the same name, it doesn't seem reliable and some devices (the iPhone 5, for example) are unable to connect and end up with a self-asigned IP address. I'm almost sure I'm doing something wrong on the setup, as I've seen a similar setup working before, so if anyone out there has any clue of what can be done, it will be much appreciated.
Attached the screenshots of both Time Capsule and AirPort Extreme configurations.
Thanks a lot,
-TM
AirPort Exteme:
Time Capsule:

Hello JuliaApple. Welcome to the Apple Discussions!
You have several ways to configure both base stations for what you are trying to do.
The simplest would be to configure the Time Capsule (TC) to "join" (AirPort Utility > Manual Setup > Wireless tab > Wireless Mode = Join a wireless network) your existing 802.11n AirPort Extreme Base Station (AEBSn). In this type of configuration the TC would perform as any other wireless client and not perform as a router. It will; however, still allow for both backups and sharing USB devices attached to it.

Are there any compatibility issues with Sonos and Airport extreme??

are there any compatibility issues with Sonos and Airport extreme??

Sonos uses its own priopietory wireless protocol SonosNet to distribute audio data among all its products, thus it should not affect other network devices which use standard WiFi 802.11a/b/g/n protocol at all though they may share the same radio channel for wirless signaling.
On my dual-band (5 GHz / 2.4 GHz) Airport Extreme staion, I select the option "802.11n Only (5GHz) - 802.11n (2.4GHz)" and turn on "Use wide channels" in Wireless configuration in order to use only 802.11n protocol and more radio channels to achieve maximum wireless bandwidth of 400 Mbps. This bandwidth is necessary for quick Time Machine backup to NAS connected to the Airport Extreme station through Ethernet cable. So my iMac and MacBook Pro always connected to the Airport Extreme through 5 GHz radio channel with 802.11n protocol whereas my iPhone 4S always connected through 2.4 GHz radio channel with the same protocol.
In my living room Sonos ZP-90 (same as new CONNECT model) zone player is connected to Airport Extreme directly through Ethernet cable (recommended by Sonos) and Sonos S5 (same as new PLAY:5 model) zone player in bedroom is connected wirelessly through SonosNet protocol to the ZP-90 zone player in living room.
These devices are in operation simutaneouly most of the time. Music is playing through the Sonos ZP90/S5 zone players througout the day, I am streaming viedo through Internet (fibre broadband 25 Mbps) on my MacBook Pro in bedroom or iMac in living room or reading news on my iPhone. So far so good and have no encounter any interference problem for about three years. Further more bandwidth for 802.11n protocol does not seem to be affected at all.
In fact with a low power Fujitsu USB drive (2.5" / 500 GB, designed for notebook) plug into USB port of Airport Extreme, it can be used as NAS drive for Sonos music distribution system without any problem. Just transfer all files from Music folder in my home directory on iMac into this NAS drive and set it up as music source in "Manage > Music Library Settings" in Sonos Controller for Mac application will do. Though the same drive can be served as Time Machine's backup disk as well, an independent full-fledged NAS drive for Sonos and Time Machine backup is better long-term solution for reliability and performance. With the NAS configured as sole music source, you do not need to keep any computer powered on all the time in order to play music through the Sonos system.

Trying to connect Verizon wireless router to Airport Extreme but error says Ethernet unplugged.

Trying to connect Verizon wireless router to Airport Extreme and error says Ethernet Unplugged.

So, AirPort Utility running on the Windows Vista desktop can "see" the AirPort Extreme and displays its icon, but gives that error message at some point in the setup process? How far does it get?
Other questions that may help me (or somebody else) understand your problem better:
Which of the pieces were verified as working before the introduction of the AirPort Extreme?
Did you have the desktop computer attached to the Verizon GT704WGB with one of the Ethernet cables you are now trying to use? Which one? Have you tried the other one to be sure it also works?
Are you using the same port on the GT704WGB? Have you tried another one?
If the desktop has multiple ethernet ports, are you using the same one?
Had you done any special configuration of the ethernet port on the Verizon GT704WGB to get it to work with your desktop?
What category ethernet cable are you using? 3? 5? 5e? 6?

PC Used to work with XP and airport Extreme Basestation but not with Vista

Please help, my PC Used to work with XP and airport Extreme Basestation but not now with Vista. I have a MacBook Pro connected and also a Mac Pro connected to the network on it and they still work, i have put the latest software on the PC and the firmware is up to date. The only thing i can see on the network on the PC is the basestation Hard Disk (shared also to the Macs) but i cannot connect with the password, i have tried everything in my knowledge, including formatting the machine and reinsatlling OS and changing security setting to no avail. Any ideas anyone?

With regard to your printer problem - take a look at this discussion:
http://discussions.apple.com/thread.jspa?messageID=6312413&tstart=0

Help setting up Open DNS with new airport extreme

I cant seem to get Open DNS to work with a new airport extreme. The status says I am not using Open DNS and its not filtering anything. I have followed the exact steps for set up listed on their website, checked the dns settings, cleared both caches and restarted the computer, modem and router with no success. I set the airport up in bridged mode, although I tried the other option under setup, but not sure what I was doing? I picked up this router because I wanted easy set up and the apple store assured me it would work with Open DNS. Oh, and I also downloaded the latest firmware update on the router. Can anyone help me with the settings or what else I need to check?

Sorry, I am not familiar with this product, so I checked online to pick up some information. Here I am referring to the information found here:
http://www.dslreports.com/faq/6096
I found that your device is mentioned as follows in the intro under Section 1 of this document:
The BellSouth supplied Westell 2100, 2200 and 6100 models (Models A90-210030-04, B90-220030-04, and B90-610030-06/C90-610030-06, respectively) share many features and functions.
Next, I am referring to the information under Section 2, under the heading of Standard Default Mode Connection (separate hub or switch present). Unless you have changed the configuration on the Westell, this is how your device is operating. In this mode, the Westell device is acting both as a modem and router in one unit.
So, an attached router (AirPort Extreme) must be configured as a switch to work correctly. That is what Bridge Mode is....the AirPort Extreme is operating as a switch when it is in Bridge Mode (which would be the correct setting to use when the Westell is set to its Standard Default Mode).
Any changes that you want to make regarding DNS settings would need to be made on the Westell device, since it is acting as the main router on your network.
In Bridge Mode, the AirPort Extreme simply passes that information through to its connected devices. You will not be able to make any DNS related changes on the AirPort Extreme since it receives that info from the Westel device. Some service providers force you to use their DNS servers, so you might want to check with Bell South or AT&T for more information in this regard.
If you want to be able to configure the AirPort Extreme as the main router on your network, and instruct it to use the DNS information that you want, you will need to refer to the section under the heading of Bridged Ethernet Mode ( separate router present).
Please note that the first item under this heading specifies that "This is the preferred configuration when using a separate external router..." (which would be the AirPort Extreme in your case)
So, it appears to me that this would be the way that you must reconfigure the Westell device to allow the AirPort Extreme to function as the "main" router on your network. In this type of setup, you will be able to enter the DNS information that you want to use under the setup for the AirPort Extreme and it will act as you instruct.
The AirPort Extreme would not be configured in Bridge Mode for this....it would be configured to "Share a public IP address".
The next item in the article specifies that you "Must use a PPPoE client on the Router." This means that the AirPort Extreme would be configured to Connect Using = PPPoE as follows:
AirPort Utility - Manual Setup
Click the Internet icon
Click the Internet Connection tab
Connect Using = PPPoE
You would enter your user name (probably your email address), password, etc in this area. Leave the Service Area box completely blank. Set Connection to Always On, and Disconnect if Idle to Never
Click Update to save the new settings. Power off the Westell device after this and then restart it so that it will pick up the new information that you have programmed into the AirPort Extreme.
I want to stress that this is how I would try to configure the Westell and AirPort Extreme. But, as I said, have not used a Westell device, so I cannot say that this will work correctly for you.
It might be an excellent idea to contact Bell South or AT&T Support to ask for their opinion on this before you decide to change the configuration of the Westel device and the AirPort Extreme.
This type of thing can be intimidating for users, so you might elect to use the services of someone like the Geek Squad at Best Buy, or a similar service from a local computer firm. Perhaps the Apple store could help as well.
If it is not critical that you use Open DNS, you might want to simply leave things "as is", with the AirPort Extreme in Bridge Mode.

Is anyone using NETGEAR Push2TV with a MacBook Pro and AirPort Extreme and does it work well for you?

I am interested in buying a NETGEAR Push2TV display TV streamer to use with my MacBook Pro and AirPort Extreme.
I saw on the Netgear site that a Intel Wireless Display/WIFI driver software is required for PC's; do we have this software installed already on our MacBook Pro's? Is any one using this box and does it work well for you, any problems or setup issues?

trying to find out same thing , store said works with new intel processor, My mini dont finding.....

Setting up PC to print on Airport Extreme Network

I just purchased an iMac and Airport Extreme. I've set up my printer on the Airport Extreme Network and can print from the iMac. While I've got the PC on the network, I'm having troubles setting up the printer. When I try to "Add a Printer" I'm not sure how to find the network and correctly setup the printer. This has to be any easy thing to do... Any suggestions?

Hello Jklink. Welcome to the Apple Discussions!
If not already, be sure to install Bonjour for Windows to facilitate printing to an AirPort base station.
(ref: Printing to an AirPort Extreme Base Station from Windows XP & Printing to a printer on a Mac running 10.4.x from a Windows PC using Bonjour for Windows)

Is the Time Capsule wi-fi router compatible with the Nest thermostat? I've read where there are issues with the Nest and Airport Extreme (AE)? Is AE used in the Time Capsule?

I've read where there are issues with the Nest and Airport Extreme (AE)? Is AE used in the Time Capsule?
If so, i already have a wi-fi router, so can the Time Capsule simply be used for wireless backup instead of as a router if there is conflict?

A TC is fundamentally a AE with a sata chip included to drive the hard disk. Some slightly different bios to include disk functions, although most of those are also on the AE. So as a router it is 99.999% identical.
And yes, if you have another router you can easily bridge the TC and use wireless for backups and internet connection. Once you no longer route through the TC the issues with most NAT problems including port forwarding should disappear.. mostly this is due to all apple routers using NAT-PMP instead of upnp which is the near universal standard for opening ports.. without upnp apple keep their routers more exclusive.

What is the default ip address for the Time Capsule and Airport Extreme?

What is the default ip address for the Time Capsule and Airport Extreme?

Open Airport Utility to find out the real IP address of the network connection. DHCP addresses are assigned by the router in the range chosen in Airport Utility.

Problems setting up Verizon DSL (DHCP) and AirPort Extreme

Similar Messages

Maybe you are looking for