Problems setting up VPN

I am trying to set up a VPN connection to my workplace network from my home. I have been unsuccessful and I am not sure of the problem but I suspect my ISP's router.
At the workplace I have the following:
Internet connection from ISP through the ISP's Netgear router ( I have no access to modify this) ISP Router is provides a range of IP numbers. Airport Extreme is assigned manually on of the numbers in this range.
Airport Extreme with most recent software. This is assigning static IP numbers to my network based on device MAC addresses. Airport Extreme Internet IP number 192.168.200.53. It is assigning ip numbers from 192.168.91.11-192.168.91.209.
Mac OS X Server 10.5 - VPN server - 192.168.91.11 VPN IP range 192.168.91.210-192.168.91.212
DNS provided by ISP xxx.xxx.30.2
From any computer on my network, if I go to www.whatismyip.com, I get the same IP number xxx.xxx.30.90.
On my remote side I have a MacBook Pro, Mac OS X 10.5.4 connecting through a Verizon wireless modem.
Could the Netgear router be preventing the connection? Will this work with the Airport connected to the ISP router?
I have set up my remote connection according to the guides and still do not get a connection.
Thanks in advance for any help.

Could the Netgear router be preventing the connection? Will this work with the Airport connected to the ISP router?
Absolutely. You'd better hope that it is.
If your AirPort has an 'internet' address of 192.168.anything then your NetGear router is performing NAT and managing all your public traffic. By default this SHOULD be set to deny any incoming connections.
If you want to permit any incoming traffic (e.g. a VPN client connection to the server) then you have to configure the router to do so (typically via 'port forwarding' where you tell it specific ports that are accessible, and what to do with the connections).
If you can't modify that router then you're out of luck. You'll need to talk to your ISP.
You may also find that the NetGear can act as a VPN server, meaning your home Mac connects to the router, eliminating the AirPort base station altogether.

Similar Messages

  • Communication problem from the vpn-anyconnect to easy-vpn-remote

    Hi Team,
    I have a communication problem from the vpn-anyconnect to easy-vpn-remote, I´ll explain better bellow and see the attached
    topology:
    1) VPN Tunnel between HQ to Branch Office - That´s OK
    2) VPN Tunnel between Client AnyConnect to HQ - That´s OK
    The idea is that the Client Anyconnect is to reach the LAN at Branch Office, but did not reach.
    The communication is stablished just when I start a session (icmp and/or rdp) from Branch Office to the Client AnyConnect,
    in this way, the communication is OK, but just during a few minutes.
    Could you help me?
    Bellow the IOS version and configurations
    ASA5505 Version 8.4(7)23 (headquarters)
    ASA5505 Version 8.4(7)23 (Branch)
    **************** Configuration Easy VPN Server (HQ) **************** 
    crypto dynamic-map DYNAMIC-MAP 5 set ikev1 transform-set ESP-AES-256-SHA
    crypto map outside-link-2_map 1 ipsec-isakmp dynamic DYNAMIC-MAP
    crypto map outside-link-2_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside-link-2_map interface outside-link-2
    access-list ACL_EZVPN standard permit 10.0.0.0 255.255.255.0 
    access-list ACL_EZVPN standard permit 192.168.1.0 255.255.255.0 
    access-list ACL_EZVPN standard permit 192.168.50.0 255.255.255.0 
    access-list ACL_EZVPN standard permit 10.10.0.0 255.255.255.0 
    group-policy EZVPN_GP internal
    group-policy EZVPN_GP attributes
     split-tunnel-policy tunnelspecified
     split-tunnel-network-list value ACL_EZVPN
     nem enable 
    tunnel-group EZVPN_TG type remote-access
    tunnel-group EZVPN_TG general-attributes
     default-group-policy EZVPN_GP
    tunnel-group EZVPN_TG ipsec-attributes
     ikev1 pre-shared-key *****
    object-group network Obj_VPN_anyconnect-local
     network-object 192.168.1.0 255.255.255.0
     network-object 192.168.15.0 255.255.255.0
    object-group network Obj-VPN-anyconnect-remote
     network-object 192.168.50.0 255.255.255.0
    object-group network NAT_EZVPN_Source
     network-object 192.168.1.0 255.255.255.0
     network-object 10.10.0.0 255.255.255.0
    object-group network NAT_EZVPN_Destination
     network-object 10.0.0.0 255.255.255.0
    nat (inside,outside-link-2) source static Obj_VPN_anyconnect-local Obj_VPN_anyconnect-local destination static Obj-VPN-
    anyconnect-remote Obj-VPN-anyconnect-remote no-proxy-arp route-lookup
    nat (inside,outside-link-2) source static NAT_EZVPN_Source NAT_EZVPN_Source destination static NAT_EZVPN_Destination 
    NAT_EZVPN_Destination no-proxy-arp route-lookup
    nat (outside-link-2,outside-link-2) source static Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote destination static 
    NAT_EZVPN_Destination NAT_EZVPN_Destination no-proxy-arp route-lookup
    **************** Configuration VPN AnyConnect (HQ) **************** 
    webvpn
     enable outside-link-2
     default-idle-timeout 60
     anyconnect-essentials
     anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
     anyconnect profiles Remote_Connection_for_TS_Users disk0:/remote_connection_for_ts_users.xml
     anyconnect enable
     tunnel-group-list enable
    access-list split-tunnel standard permit 192.168.1.0 255.255.255.0 
    access-list split-tunnel standard permit 192.168.15.0 255.255.255.0 
    access-list split-tunnel standard permit 10.0.0.0 255.255.255.0 
    group-policy clientgroup internal
    group-policy clientgroup attributes
     wins-server none
     dns-server value 192.168.1.41
     vpn-tunnel-protocol ssl-client 
     split-tunnel-policy tunnelspecified
     split-tunnel-network-list value split-tunnel
     default-domain value ipconnection.com.br
     webvpn       
      anyconnect keep-installer installed
      anyconnect ssl rekey time 30
      anyconnect ssl rekey method ssl
      anyconnect profiles value Remote_Connection_for_TS_Users type user
      anyconnect ask none default anyconnect
    tunnel-group sslgroup type remote-access
    tunnel-group sslgroup general-attributes
     address-pool vpnpool
     authentication-server-group DC03
     default-group-policy clientgroup
    tunnel-group sslgroup webvpn-attributes
     group-alias IPConnection-vpn-anyconnect enable
    object-group network Obj_VPN_anyconnect-local
     network-object 192.168.1.0 255.255.255.0
     network-object 192.168.15.0 255.255.255.0
    object-group network Obj-VPN-anyconnect-remote
     network-object 192.168.50.0 255.255.255.0
    object-group network NAT_EZVPN_Source
     network-object 192.168.1.0 255.255.255.0
     network-object 10.10.0.0 255.255.255.0
    object-group network NAT_EZVPN_Destination
     network-object 10.0.0.0 255.255.255.0
    nat (inside,outside-link-2) source static Obj_VPN_anyconnect-local Obj_VPN_anyconnect-local destination static Obj-VPN-
    anyconnect-remote Obj-VPN-anyconnect-remote no-proxy-arp route-lookup
    nat (inside,outside-link-2) source static NAT_EZVPN_Source NAT_EZVPN_Source destination static NAT_EZVPN_Destination 
    NAT_EZVPN_Destination no-proxy-arp route-lookup
    nat (outside-link-2,outside-link-2) source static Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote destination static 
    NAT_EZVPN_Destination NAT_EZVPN_Destination no-proxy-arp route-lookup

    Hi,
    the communication works when you send traffic from easyvpn branch side because it froms the IPSEC SA for local subnet and anyconnect HQ pool. The SA will only form when branch initiates the connection as this is dynamic peer connection to HQ ASA.
    when there no SA between branch and HQ for this traffic, HQ ASA has no clue about where to send the traffic from anyconnect to branch network.
    I hope it explains the cause.
    Regards,
    Abaji.

  • Problem establishing SSL VPN from only 1 IP address

    Hi,
    I'm experiencing strange problem.
    I can't establish SSL VPN connection from 1 IP address, but I don't have problem establishing SSL VPN from any other IP address.
    Remote IP address: 10.0.0.1
    ASA's public IP address: 192.168.1.1
    Output of packet-tracer:
    1. with problematic source IP address:
    packet-tracer input wan tcp 10.0.0.1 50601 192.168.1.1 443 detailed
    Phase: 1
    Type: ROUTE-LOOKUP
    Subtype: input
    Result: ALLOW
    Config:
    Additional Information:
    in   192.168.1.1   255.255.255.255 identity
    Phase: 2
    Type: ACCESS-LIST
    Subtype:
    Result: ALLOW
    Config:
    Implicit Rule
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff37573f00, priority=119, domain=permit, deny=false
            hits=861, user_data=0x0, cs_id=0x0, flags=0x0, protocol=6
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=443, dscp=0x0
            input_ifc=wan, output_ifc=identity
    Phase: 3
    Type: CONN-SETTINGS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff38a10a50, priority=8, domain=conn-set, deny=false
            hits=4069, user_data=0x7fff38770910, cs_id=0x0, reverse, flags=0x0, protocol=6
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
            input_ifc=wan, output_ifc=identity
    Phase: 4
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff395c7d70, priority=0, domain=inspect-ip-options, deny=true
            hits=4044934, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
            input_ifc=wan, output_ifc=any
    Phase: 5
    Type: VPN
    Subtype: ipsec-tunnel-flow
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff37560700, priority=13, domain=ipsec-tunnel-flow, deny=true
            hits=2268518, user_data=0x0, cs_id=0x0, flags=0x0, protocol=0
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
            input_ifc=wan, output_ifc=any
    Phase: 6
    Type: TCP-MODULE
    Subtype: webvpn
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff38a10cc0, priority=13, domain=soft-np-tcp-module, deny=false
            hits=4627, user_data=0x7fff38c14300, cs_id=0x0, reverse, flags=0x0, protocol=6
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
            input_ifc=wan, output_ifc=identity
    Phase: 7
    Type: VPN
    Subtype: encrypt
    Result: DROP
    Config:
    Additional Information:
    Reverse Flow based lookup yields rule:
    out id=0x7fff375504a0, priority=69, domain=encrypt, deny=false
            hits=40747, user_data=0x0, cs_id=0x7fff3754fa40, reverse, flags=0x0, protocol=0
            src ip/id=192.168.1.1, mask=255.255.255.255, port=0
            dst ip/id=10.0.0.1, mask=255.255.255.255, port=0, dscp=0x0
            input_ifc=any, output_ifc=wan
    Result:
    input-interface: wan
    input-status: up
    input-line-status: up
    output-interface: NP Identity Ifc
    output-status: up
    output-line-status: up
    Action: drop
    Drop-reason: (acl-drop) Flow is denied by configured rule
    If I run packet-tracer with any other source IP address, let's say 10.0.0.2, everything is OK:
    packet-tracer input wan tcp 10.0.0.2 50601 192.168.1.1 443 de
    Phase: 1
    Type: ROUTE-LOOKUP
    Subtype: input
    Result: ALLOW
    Config:
    Additional Information:
    in   192.168.1.1   255.255.255.255 identity
    Phase: 2
    Type: ACCESS-LIST
    Subtype:
    Result: ALLOW
    Config:
    Implicit Rule
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff37573f00, priority=119, domain=permit, deny=false
            hits=862, user_data=0x0, cs_id=0x0, flags=0x0, protocol=6
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=443, dscp=0x0
            input_ifc=wan, output_ifc=identity
    Phase: 3
    Type: CONN-SETTINGS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff38a10a50, priority=8, domain=conn-set, deny=false
            hits=4090, user_data=0x7fff38770910, cs_id=0x0, reverse, flags=0x0, protocol=6
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
            input_ifc=wan, output_ifc=identity
    Phase: 4
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff395c7d70, priority=0, domain=inspect-ip-options, deny=true
            hits=4047886, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
            input_ifc=wan, output_ifc=any
    Phase: 5
    Type: VPN
    Subtype: ipsec-tunnel-flow
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff37560700, priority=13, domain=ipsec-tunnel-flow, deny=true
            hits=2270040, user_data=0x0, cs_id=0x0, flags=0x0, protocol=0
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
            input_ifc=wan, output_ifc=any
    Phase: 6
    Type: TCP-MODULE
    Subtype: webvpn
    Result: ALLOW
    Config:
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x7fff38a10cc0, priority=13, domain=soft-np-tcp-module, deny=false
            hits=4648, user_data=0x7fff38c14300, cs_id=0x0, reverse, flags=0x0, protocol=6
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=192.168.1.1, mask=255.255.255.255, port=443, dscp=0x0
            input_ifc=wan, output_ifc=identity
    Phase: 7
    Type: USER-STATISTICS
    Subtype: user-statistics
    Result: ALLOW
    Config:
    Additional Information:
    Reverse Flow based lookup yields rule:
    out id=0x7fff3a1cc320, priority=0, domain=user-statistics, deny=false
            hits=4902651, user_data=0x7fff3a0043c0, cs_id=0x0, reverse, flags=0x0, protocol=0
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
            input_ifc=any, output_ifc=wan
    Phase: 8
    Type: FLOW-CREATION
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    New flow created with id 4384689, packet dispatched to next module
    Module information for forward flow ...
    snp_fp_tracer_drop
    snp_fp_inspect_ip_options
    snp_fp_tcp_normalizer
    snp_fp_tcp_mod
    snp_fp_adjacency
    snp_fp_fragment
    snp_fp_drop
    Module information for reverse flow ...
    snp_fp_tracer_drop
    snp_fp_inspect_ip_options
    snp_fp_tcp_normalizer
    snp_fp_adjacency
    snp_fp_fragment
    snp_ifc_stat
    Result:
    input-interface: wan
    input-status: up
    input-line-status: up
    output-interface: NP Identity Ifc
    output-status: up
    output-line-status: up
    Action: allow
    I run packet capture on WAN interface - and I can only see incoming packets (SYN) with destination to tcp/443 but there isn't any outgoing packet (SYN/ACK).
    I even can't open web page from internet browser (url https://192.168.1.1) when source IP is 10.0.0.1, but I can open "SSL VPN Service" web page from any other source IP address.
    The only thing different with this IP address is that there's configured site-to-site (IPsec) vpn tunnel from same source to same destination IP address.
    Here is the configuration of the tunnel:
    group-policy GroupPolicy_10.0.0.1 internal
    group-policy GroupPolicy_10.0.0.1 attributes
    vpn-filter value VPN-ACL
    vpn-tunnel-protocol ikev1 ssl-client
    access-list VPN-ACL:
    access-list VPN-ACL extended permit ip object-group DM_INLINE_NETWORK_83 object-group DM_INLINE_NETWORK_84
    object-group network DM_INLINE_NETWORK_83
    network-object 10.11.217.0 255.255.255.0
    network-object 192.168.201.0 255.255.255.0
    object-group network DM_INLINE_NETWORK_84
    network-object 10.11.217.0 255.255.255.0
    network-object 192.168.201.0 255.255.255.0
    tunnel local & remote networks:
    access-list wan_cryptomap_5 extended permit ip 10.11.217.0 255.255.255.0 192.168.201.0 255.255.255.0
    crypto map wan_map 5 match address wan_cryptomap_5
    crypto map wan_map 5 set connection-type answer-only
    crypto map wan_map 5 set peer 10.0.0.1
    crypto map wan_map 5 set ikev1 transform-set ESP-3DES-SHA
    I've configured the same setup in my lab and I can't reproduce the error.
    The SW version running on ASA is asa861-12.
    I'm out of ideas.

    Just collected some other information:
    1. traceroute shows that traffic is not leaving ASA at all
    1   *  *  *
    2   *  *  *
    3   *  *  *
    I double checked that there is no "strange" entry for remote public IP in routing. Traffic with destination to remote IP should be sent via default gateway like all other traffic.
    2. debug crypto ipsec shows this information when I ping public IP address of the remote host (with VPN
    IPSEC(crypto_map_check)-3: Looking for crypto map matching 5-tuple: Prot=1, saddr=192.168.1.1, sport=30647, daddr=10.0.0.1, dport=30647
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 1: skipping because 5-tuple does not match ACL wan_cryptomap_1.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 2: skipping because 5-tuple does not match ACL wan_cryptomap_2.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 3: skipping because 5-tuple does not match ACL wan_cryptomap_3.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 4: skipping because 5-tuple does not match ACL wan_cryptomap_4.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 5: skipping dormant map.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 5: skipping dormant map.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 6: skipping because 5-tuple does not match ACL wan_cryptomap_6.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 7: skipping because 5-tuple does not match ACL wan_cryptomap_7.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 8: skipping because 5-tuple does not match ACL wan_cryptomap_8.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 9: skipping because 5-tuple does not match ACL wan_cryptomap_9.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 10: skipping because 5-tuple does not match ACL wan_cryptomap_10.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 11: skipping because 5-tuple does not match ACL wan_cryptomap_11.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 13: skipping because 5-tuple does not match ACL wan_cryptomap_13.
    IPSEC(crypto_map_check)-5: Checking crypto map wan_map 65535: skipping dynamic_link.
    IPSEC(crypto_map_check)-1: Error: No crypto map matched.
    It really seems that the whole problem is that ASA is trying to encrypt traffic sent from public IP address of one VPN endpoint and targeted to public IP address of another VPN endpoint and send it to remote VPN endpoint via IPcec tunel.
    There is indeed VPN tunnel established between both VPN endpoints, but there are just local and remote networks defined with private IP address space for this tunnel, VPN endpoint's public IP addresses are not included in the definition of this IPsec VPN tunnel.
    And there are at least two more IPsec VPN tunnels configured the same way and I can't reprodure this error on there two VPN tunnels.
    Any idea?

  • Problems setting up username & password for SQL

    Due to the outstanding advice I recieved from this excellent forum, I have managed to overcome my first problem with declaring a new Class.
    This leads me to request help with my next biggest problem:
    Setting up a user GUI that takes a "username" & "password" that will be used to access a password protected database.
    I am a simple bloke, with simple thought processes, so please, go easy on me...
    import java.awt.*;
    import java.awt.event.*;
    import javax.swing.*;
    import java.sql.*;
    public class DBQuery1 {
         String username = "" , password = "";
         public static void main(String[] arguments) {
              PassDB UPass = new PassDB();
              String data = "jdbc:odbc:JavaTestDataBase";
              try {
                   Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
                   Connection conn = DriverManager.getConnection(data, "" + username, "" + password);
                   Statement st = conn.createStatement();
                   ResultSet rec = st.executeQuery(
                        "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                        + "WHERE (Title='Mr') ORDER BY ContactID");
              /*     ResultSet rec2 = st.executeQuery(
                        "SELECT Subject, ContactID FROM Calls "
                        + "WHERE (Subject Is Not Null) ORDER BY ContactID");
              System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
              while(rec.next()) {
                   System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
              st.close();
              catch (SQLException s) {
                   System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
              catch (Exception e) {
                   System.out.println("Error: " + e.toString() + e.getMessage());
    class PassDB extends javax.swing.JFrame implements ActionListener {
         String username = "", password = "";
         JTextField uname = new JTextField(10);
         JTextField pword = new JTextField(10);
         // JPasswordField pword = new JTextField(10);
         PassDB() {
              super("duBe's database logon");
              setSize(220, 160);
              setDefaultCloseOperation(EXIT_ON_CLOSE);
              JPanel pane = new JPanel();
              JLabel unameLabel = new JLabel ("Username: ");
              JLabel pwordLabel = new JLabel ("Password: ");
              JButton submit = new JButton("OK");
              submit.addActionListener(this);
              pane.add(unameLabel);
              pane.add(uname);
              pane.add(pwordLabel);
              pane.add(pword);
              pane.add(submit);
              setContentPane(pane);
              setVisible(true);
         public void actionPerformed(ActionEvent evt) {
              PassDB clicked = (PassDB)evt.getSource();
              username = uname.getText();
              password = pword.getText();
    This code generates two errors, stating:
    C:\Java_progs>javac DBQuery1.java
    DBQuery1.java:14: non-static variable username cannot be referenced from a static context
    Connection conn = DriverManager.getConnection(data, "" +
    username, "" + password);
    ^
    DBQuery1.java:14: non-static variable password cannot be referenced from a static context
    Connection conn = DriverManager.getConnection(data, "" +
    username, "" + password);
                    ^
    2 errors*****************************
    The code works when I remove the reference to the variables "username" & "password" in Connection "conn" call & replace them with the actual username & password, but this is not exactly what I was after. I was hoping to make the program responsive to each individual user, not set in code.
    I also would like to make the program pause after the call in "main" to "PassDB" to wait for "PassDB" to exit before continuing.
    I would also like to make "PassDB" destroy itself after the "OK" button is pressed & the "username" & "password" set.
    If that isn't enough for you, I would really like the program to search 2 different database tables, return their values & compare them to be sure that they are the same.
    When I try & search 2 different tables, as in:
    ResultSet rec = st.executeQuery(
                        "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                        + "WHERE (Title='Mr') ORDER BY ContactID");
                   ResultSet rec2 = st.executeQuery(
                        "SELECT Subject, ContactID FROM Calls "
                        + "WHERE (Subject Is Not Null) ORDER BY ContactID")javac tells me that "ResultSet" is set to null 0
    As always, I am extremely appreciative of any assistance you are able to offer.
    Kind regards
    duBedat
    [email protected]

    This is where I'm at now:
    import java.awt.*;
    import java.awt.event.*;
    import javax.swing.*;
    import java.sql.*;
    public class DBQuery {
         static String username = "" ;
         static String password = "" ;
         public static void main(String[] arguments) {
         PassDB UPass = new PassDB();
         String data = "jdbc:odbc:JavaTestDataBase";
         try {
              Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
              Connection conn = DriverManager.getConnection(data, "" + DBQuery.username, "" + DBQuery.password);
              Statement st = conn.createStatement();
              ResultSet rec = st.executeQuery(
              "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
              + "WHERE (Title='Mr') ORDER BY ContactID");
              /*     ResultSet rec2 = st.executeQuery(
                   "SELECT Subject, ContactID FROM Calls "
                   + "WHERE (Subject Is Not Null) ORDER BY ContactID");
              System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
              while(rec.next()) {
                   System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
              st.close();
         catch (SQLException s) {
              System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
         catch (Exception e) {
              System.out.println("Error: " + e.toString() + e.getMessage());
    class PassDB extends javax.swing.JFrame implements ActionListener {
         static boolean getOut = false;
         JTextField uname = new JTextField(10);
         JTextField pword = new JTextField(10);
         // JPasswordField pword = new JTextField(10);
         public PassDB() {
              super("duBe's database logon");
              setSize(220, 160);
              setDefaultCloseOperation(EXIT_ON_CLOSE);
              JPanel pane = new JPanel();          
              JLabel unameLabel = new JLabel ("Username: ");
              JLabel pwordLabel = new JLabel ("Password: ");
              JButton submit = new JButton("OK");
              submit.addActionListener(this);
              pane.add(unameLabel);
              pane.add(uname);
              pane.add(pwordLabel);
              pane.add(pword);
              pane.add(submit);
              setContentPane(pane);
              while(getOut == false)
                   setVisible(true);                         
         public void actionPerformed(ActionEvent evt) {
              PassDB clicked = (PassDB)evt.getSource();
              DBQuery.username = uname.getText();
              DBQuery.password = pword.getText();
              getOut = true;               
    }          Any advice is greatly appreciated
    duBe

  • Problems setting up an NFS server

    Hi everybody,
    I just completed my first arch install. :-)
    I have a desktop and a laptop, and I installed Arch on the desktop (the laptop runs Ubuntu 9.10). I had a few difficulties here and there, but I now have the system up and running, and I'm very happy.
    I have a problem setting up an NFS server. With Ubuntu everything was working, so I'm assuming that the Ubuntu machine (client) is set-up correctly. I'm trying to troubleshoot the arch box (server) now.
    I followed this wiki article: http://wiki.archlinux.org/index.php/Nfs
    Now, I have these problems:
    - when I start the daemons, I get:
    [root@myhost ~]# /etc/rc.d/rpcbind start
    :: Starting rpcbind [FAIL]
    [root@myhost ~]# /etc/rc.d/nfs-common start
    :: Starting rpc.statd daemon [FAIL]
    [root@myhost ~]# /etc/rc.d/nfs-server start
    :: Mounting nfsd filesystem [DONE]
    :: Exporting all directories [BUSY] exportfs: /etc/exports [3]: Neither 'subtree_check' or 'no_subtree_check' specified for export "192.168.1.1/24:/home".
    Assuming default behaviour ('no_subtree_check').
    NOTE: this default has changed since nfs-utils version 1.0.x
    [DONE]
    :: Starting rpc.nfsd daemon [FAIL]
    - If I mount the share on the client with "sudo mount 192.168.1.20:/home /media/desktop", IT IS mounted but I can't browse it because I have no privileges to access the home directory for the user.
    my /etc/exports looks like this:
    # /etc/exports: the access control list for filesystems which may be exported
    # to NFS clients. See exports(5).
    /home 192.168.1.1/24(rw,sync,all_squash,anonuid=99,anongid=99))
    /etc/conf.d/nfs-common.conf:
    # Parameters to be passed to nfs-common (nfs clients & server) init script.
    # If you do not set values for the NEED_ options, they will be attempted
    # autodetected; this should be sufficient for most people. Valid alternatives
    # for the NEED_ options are "yes" and "no".
    # Do you want to start the statd daemon? It is not needed for NFSv4.
    NEED_STATD=
    # Options to pass to rpc.statd.
    # See rpc.statd(8) for more details.
    # N.B. statd normally runs on both client and server, and run-time
    # options should be specified accordingly. Specifically, the Arch
    # NFS init scripts require the --no-notify flag on the server,
    # but not on the client e.g.
    # STATD_OPTS="--no-notify -p 32765 -o 32766" -> server
    # STATD_OPTS="-p 32765 -o 32766" -> client
    STATD_OPTS="--no-notify"
    # Options to pass to sm-notify
    # e.g. SMNOTIFY_OPTS="-p 32764"
    SMNOTIFY_OPTS=""
    # Do you want to start the idmapd daemon? It is only needed for NFSv4.
    NEED_IDMAPD=
    # Options to pass to rpc.idmapd.
    # See rpc.idmapd(8) for more details.
    IDMAPD_OPTS=
    # Do you want to start the gssd daemon? It is required for Kerberos mounts.
    NEED_GSSD=
    # Options to pass to rpc.gssd.
    # See rpc.gssd(8) for more details.
    GSSD_OPTS=
    # Where to mount rpc_pipefs filesystem; the default is "/var/lib/nfs/rpc_pipefs".
    PIPEFS_MOUNTPOINT=
    # Options used to mount rpc_pipefs filesystem; the default is "defaults".
    PIPEFS_MOUNTOPTS=
    /etc/hosts.allow:
    nfsd: 192.168.1.0/255.255.255.0
    rpcbind: 192.168.1.0/255.255.255.0
    mountd: 192.168.1.0/255.255.255.0
    Any help would be very appreciated!

    Thanks, I finally got it working.
    I realized that even though both machines had the same group, my Ubuntu machine (client) group has GID 1000, while the Arch one has GID 1001. I created a group that has GID 1001 on the client, and now everything is working.
    I'm wondering why my Arch username and group both have 1001 rather than 1000 (which I suppose would be the default number for the first user created).
    Anyway, thanks again for your inputs.

  • Problems setting up static routing

    HI
    I'm having a problem setting up static routing.  I keep getting the message "invalid static route".   I have an E1550 router and my frimware is up to date.  I have tried a few different gateway addresses ie 192.168.1.1,  127.0.0.1 and my router's address on the net, but I keep getting the same message.  Has anyone else had this problem and been able to fix it?

    I think the E1550 router supports LAN to LAN routing provided that you have two local networks. If you only have a plain modem and the E1550, I believe you can't do Static routing on that type of setup. Found this link that might help: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=12a84336a124498eb5d6f0204b85191e_17589.xml&pid=80&...

  • Problems Setting Up Developer Users

    I am having a problem setting up developer users and I am trying to determine if I am missing a step or if there is a configuration problem on my staging and production systems.
    What I want to do should be very simple. I want to create a user that can create an application and see the information under the "Application" tab in the Navigator.
    I have created the user using the following steps on 3.0.9.82 for Unix:
    1. Create the user
    2. Make the user a full administrator (rather than end user)
    3. Make the user a member of the portal_developers group
    4. Make the user's default group the portal_developers group
    However, when I do this the user does not see the information under the
    "Application" tab. The only way I can get the user to see the info under the
    "Application" tab is to make him a member of the Portal_administrators
    and/or DBA group. Both my staging and production boxes have the same result.
    Does anyone have any thoughts or suggestions on what might be happening?

    Thank you- I have read through that thread and can see some resonance with my issue.
    My AOL emails work VERY fast with BB, in fact almost simultaneously received on PC & Torch " ping ping!"
    This issue only raised its ugly head when I had 2 Torches replaced by my insurers. 
    Whilst the claim was in process I used a new Curve, loaded from backup on PC to keep emails going and of course phone & web facilities. ( I use the BB to power internet via bluetooth to my PC / laptop when living on a remote island with no phone lines or power supplies)  All was fine. Swapping email accounts took a few minutes with the usual password confirmations for each AOL screenname etc. 
    Then the new Torches came back from insurers, and I tried to swap devices. Phoning & texting is fine. Al data and contacts swap over fine.
    SETUP email accounts.............stymied every time. It says repeatedly that my user name/password is invalid etc etc etc
    Have tried security wipes. Have tried setting up new BB ID & passwords on PC website. All is OK until I try to setup emails on the Torches.  This has used up ridiculous amounts of time- all wasted.
    I love the BB phones and the fast email push......in fact I recently bought a new Sony Xperia Z1 but sent it back because of wifi coverage meant no emails on that superb phone for lots of the time.
    Good old BB I said..........I always get emails wherever I am. ( Rural Scotland has very patchy radio & wifi coverage)  
    Was about to purchase new Z10s just to get a bigger screen, but now I am averse to buying ANY BB phone again because this present mess means I may never get emails set up again.  How nuts is that?
    Many thanks for all help & suggestions..........boy do I need them!!
    Kind wishes from West of Scotland 
    Fair winds and kind landfalls

  • Problems setting up VVSA 6.0 (lookup service adresse)

    Hi,
    I was happy to see VVSA 6.0 released, but i'm having problems setting it up. It keeps saying that the lookup service adresse is not reachable. But I have tried with the VVSA 5.5 and 5.5.1.1 and they work just fine with the lookup service adresse.
    Anyone else having this issue?
    Also trying to check for updates within the appliance failes since the repository is not online at vmware it seems.
    Might not be ready for primetime (like ESXi6).

    If Developer has a separate Oracle Home on your PC, then it has a separate TNSNAMES.ORA file that is uses to connect to the database. If you search for all tnsnames.ora files, you should find the one used by Developer 6.
    Since Enterprise manager works, the tnsnames.ora in your Enterprise Manager's home will have an entry for your server database. You should be able to cut and paste this into the tnsnames.ora file used by Developer, or try copying the E.M. tnsnames.ora file directly.
    John Alexander www.SummitSoftwareDesign.com

  • Problems setting up JDBC

    I recently downloaded mysql Connector for my project.
    However, I have problems setting it up.
    When I run my program, It gives me a class not defined error.
    System.out.println("Registering Driver...");
                   Class.forName("com.mysql.jdbc.Driver").newInstance();
    System.out.println("Connected to database");
    System.out.println("Creating Connection");
    connection= DriverManager.getConnection("jdbc:mysql://localhost:8080/neuis");
    System.out.println("Connection created");
    catch(Exception ex)
    System.out.println("Error in loading jdbc Driver: "+ex);
    ex.printStackTrace();
    I have put the jar file of the JDBC Bridge in a folder
    C:\Drivers\Sql Connector
    I have also added the absolute path of the jar to the system classpath
    The value put in is:
    C:\Drivers\Sql Connector\mysql-connector-java-3.1.10-bin.jar.
    I am not sure what the problem is because I was told by the API that this was all I needed to do. Are there any other files I need to include with the jar file? Also, Is there a specific folder I must put it in?
    Thank you in advance.

    Hi,
    Take a look at the below link
    http://www.cs.nott.ac.uk/TSG/manuals/databases/mysql/jdbc.html
    may help you to setting up the jdbc with mysql
    regards
    MJ

  • Problems setting up email account

    Have recently got a blackberry 9300 and having problems setting up my aol email account. 
    Do not know how to fix this problem, can anyone please give advice?

    Hi and Welcome to the Forums!
    Well, a bit more detail than "having problems" might help us just a bit...keep us from guessing, after all. In the meantime, see this:
    http://us.blackberry.com/support/blackberry101/set​up.jsp#tab_tab_email
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Problems Setting up my wireless network with an Xb...

    Hi, I have had some problems setting up my wireless networking.
    I have everything switched on and am able to go online with the laptop and the Xbox with no problems but when I try to share media with the xbox I have problems.
    I have opened the ports specified in the setup from xbox on windows firewall and have no problem connection Via Ethernet cable but when using wireless the xbox cannot detect the laptop.
    I have checked the network map and both xbox and laptop are connected and have enabled sharing and am running sharing software.
    Below is the network map.
    I have also been having problems with BT software, the free virus protection will not install, The desktop help will not launch although it shows up on task manager and the installation disk does not launch correctly it doesn't get past the loading screen.
    I have had a printer on the wireless network and had no problems printing.
    If anyone knows how to resolve this please help.

    I have this same Motorola modem and I just verified that my 802.11n AirPort Express Base Station (AXn) can get Internet access with this modem without any issues.
    When changing ISPs (or networking equipment) it's always a good idea to start from "scratch" in configuring your equipment.
    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Power-up the modem; wait at least 10-15 minutes.
    Power-up the base station; wait at least 5-10 minutes.
    Power-up your computer(s).
    In this basic configuration, computers connected to the base station, either by wire or wireless (as appropriate for the base station type), should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options.

  • Problems Setting up NFS

    Hi.
    I've been having problems setting up NFS on a LAN at home.  I've read through all the Arch NFS-related threads and looked at (and tried some of) the suggestions, but without success.
    What I'm trying to do is set up an NFS share on a wireless laptop to copy one user's files from the laptop to a wired workstation.  The laptop is running Libranet 2.8.1. The workstation is running Arch Linux with the most up-to-date (as of today) software, including NFS.
    I have the portmap, nfslock, and nfsd daemons running via rc.conf, set to run in that order.
    I've re-installed nfs-utils and set up hosts.deny as follows:
    # /etc/hosts.deny
    ALL: ALL
    # End of file
    and hosts.allow as follows:
    # /etc/hosts.allow
    ALL: 192.168.0.0/255.255.255.0
    ALL: LOCAL
    # End of file
    In other words, I want to allow access on the machine to anything running locally or on the LAN.
    I have the shared directories successfully exported from the laptop (192.168.0.3), but I have not been able to mount the exported directories on the workstation (192.168.0.2).
    The mount command I'm using at the workstation:
    mount -t nfs -o rsize=8192,wsize=8192 192.168.0.3:/exports /exports
    There is an /exports directory on both machines at root with root permissions. There is an /etc/exports file on the NFS server machine that gives asynchronous read/write permissions to 192.168.0.2 for the /exports directory.
    I receive the following message:
    mount: RPC: Program not registered
    This appears to be a hosts.allow/hosts.deny type problem, but I can't figure out what I need to do to make RPC work properly.
    Some additional information, just in case it's helpful:
    This is the result if running rpcinfo:
       program vers proto   port
        100000    2   tcp    111  portmapper
        100000    2   udp    111  portmapper
        100024    1   udp  32790  status
        100024    1   tcp  32835  status
        100003    2   udp   2049  nfs
        100003    3   udp   2049  nfs
        100003    4   udp   2049  nfs
        100003    2   tcp   2049  nfs
        100003    3   tcp   2049  nfs
        100003    4   tcp   2049  nfs
        100021    1   udp  32801  nlockmgr
        100021    3   udp  32801  nlockmgr
        100021    4   udp  32801  nlockmgr
        100021    1   tcp  32849  nlockmgr
        100021    3   tcp  32849  nlockmgr
        100021    4   tcp  32849  nlockmgr
        100005    3   udp    623  mountd
        100005    3   tcp    626  mountd
    Running ps shows that the following processes are running:
    portmap
    rpc.statd
    nfsd
    lockd
    rpciod
    rpc.mountd
    Thanks for any help here!
    Regards,
    Win

    Hi ravster.
    Thanks for the suggestions. I had read the Arch NFS HowTo and did as you suggested get rcpinfo for the server machine. The Libranet NFS server is configured rather different since the NFS daemons are built into the default kernel.
    Since I needed to complete the transfer immediately, I gave up for now trying to set up NFS and used netcat (!) instead to transfer the files from the Libranet laptop to the Arch workstation. The laptop will be converted to Arch Linux soon so I think I'll be able to clear things up soon.  I haven't had any problems setting up NFS with homogeneous (i.e., all Arch or all Libranet) computer combinations.
    Thanks again.
    Win

  • Problems setting up Mail to Exchange

    Hey everyone,
    Having a few problems setting up mail to exchange on a Nokia 5800.
    We have the latest version of Mail to Exchange installed.
    Were using Microsoft Exchange 2007.
    Example serup of what we have done:
    Mail to exchange - New profile - Input Username and Password of domain account - Input domain name - Chose Internet as means of connection -
    The Nokia goes off and searches for the domain information, finds it OK. Shows a message regarding a server certificate, we chose to install this certificate this time only.
    Phone crashes?
    Any ideas whats going on?
    Thansk

    Hi Jim,
    Depending on the customer feedback, it works fine. Apple Mail the client that comes with OSX supports standard protocols (POP3, IMAP, SMTP), these are all supported by Exchange 2010. 
    If you're running Mac OS 10.4 Tiger or Mac OS 10.5 Leopard, you can still use the Mac Mail App to connect to your account. However, you need to connect to your account without using IMAP or POP.
    If you're running Mac OS 10.6 Snow Leopard or Mac OS 10.7 Lion, you can use the Mail program included with those releases to connect to your email account automatically using an Exchange account.
    When you use Mac OS 10.6 Snow Leopard or Mac OS 10.7 Lion and connect using an Exchange account, you can use features that aren't available to users who connect through IMAP or POP, including iCal and Address Book.
    More details about Set up email in Mac OS X Mail, please refer to:
    https://support.office.microsoft.com/en-in/article/Set-up-email-in-Mac-OS-X-Mail-de372dc4-9648-4044-a76c-e8a60e178d54?CorrelationId=a0ce4c19-1492-4e3b-bc7e-4af83d3cb347&ui=en-US&rs=en-IN&ad=IN
    Additional, I find a similar thread about your question, for your reference:
    https://social.technet.microsoft.com/Forums/exchange/en-US/b112b61e-401f-4ad9-b459-a25673ff5407/connecting-to-exchange-2010-using-apple-mail?forum=exchange2010
    https://social.technet.microsoft.com/Forums/en-US/d3c9b4ad-822b-4a7c-88b8-39df3f166f96/how-to-setup-exchange-account-on-macbook-os-x?forum=exchange2010
    Best Regards,
    Allen Wang

  • Problems Setting up a Direct Debit

    has anyone experienced any problems setting up a direct debit ??
    I've been a BT customer for approximately 20 years and have had the same account number. I've moved house a few times and retained the same account. My last house move wasn't so successful as after moving in and having broadband re set up again... I received a letter in the post saying I had requested a "termination" and a parcel was included to send my router back etc... plus... I'd be charged £100+ for the disconnection...
    Anyway I got on the phone to BT and the advisor appologised for the mix up... and suggested I cancel my direct debit with the bank to make sure the disconnection fee wasn't taken from my account..... 
    Ever since then... I have not being able to set up a direct debit online or by speaking with several BT helpdesk staff.  I email BT asking for an explaination - NOTHING.  BT helpdesk staff assure me that the direct debit will work this time and will contact me if there is a problem... again NOTHING.  I even tried writing a letter to the head of customer services... I think the name Warren Buckley rings a bell..   Someone did email me back suggesting I use the online facility.... REALLY!!  Do BT not have a fault tracking database of customer issues... so they can see I've already tried to set up the direct debit online... 
    Anyway ..... I've just noticed this forum now... so this is my latest attempt to see if anyone senior enough at BT will be embarrassed and try and sort out my account so I can start paying my bill using Direct Debit again... I'm pretty sure all that needs to happen is to be given a new account number or an account alias that can be sent to my bank. Otherwise... I'll just carry on waiting to receive the automated message from BT saying I haven't paid and then go and pay online... But I am worried one of these automated messages will arrive the day I go on a 2 week holiday and I find myself cut off when I get home... giving me more pain....
    PLEASE HELP BT ;o) 
    regards
    DaveB

    I have asked a moderator to provide assistance, they will post an invite on this thread.
    They are the only BT employees on this forum, and are a UK based team of people, who take personal ownership of your problem.
    Once you get a reply, if you click on their name, you will see a screen like this. Click on the link as shown below.
    Please do not send them a personal message, as they may not be on duty for a long time, and your message will not be tracked properly.
    For your own security, do not post any personal details, on this forum. That includes any tracking number you are give.
    They will respond either by phone or e-mail within 5-6 working days.
    Please use the tracked e-mail, to reply, not via the forum. Thanks
    This is the form you should see when you click on the link. If you do not see this form, then you have selected the wrong link.
    When you submit the form, you will receive an enquiry number, so please keep a note of it
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Problems setting up MPLS

    A Chairde,
    Am having problems setting up MPLS between a AS5350 and 7609 , I have used commands stated in this link, enable MPLS incrementally on a network.
    http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/switch_c/xcprt4/xcdtagc.pdf
    The commands below are added to each router, and some troubleshooting.
    7609
    ip cef distributed
    interface Loopback0
    ip address 192.168.254.1 255.255.255.255
    tag-switching advertise-tags
    interface GigabitEthernet3/12
    ip address 192.168.230.162 255.255.255.248
    mpls label protocol tdp
    tag-switching ip
    AS5350
    ip cef
    mpls label protocol tdp
    tag-switching advertise-tags
    interface Loopback0
    ip address 192.168.254.2 255.255.255.255
    interface FastEthernet0/0
    ip address 192.168.230.161 255.255.255.248
    duplex auto
    speed auto
    mpls ip
    h323-gateway voip interface
    h323-gateway voip id cnibhco111 ipaddr 192.168.230.129 1719
    h323-gateway voip h323-id cnibhco112
    h323-gateway voip tech-prefix 71401
    h323-gateway voip tech-prefix 0030
    h323-gateway voip bind srcaddr 192.168.230.161
    ip rsvp bandwidth 64 64
    cnibhco112#sh tag-switching tdp neighbor
    Peer TDP Ident: 192.168.254.1:0; Local TDP Ident 192.168.230.161:0
    TCP connection: 192.168.254.1.49842 - 192.168.230.161.711
    State: Oper; PIEs sent/rcvd: 18/23; Downstream
    Up time: 00:12:54
    TDP discovery sources:
    FastEthernet0/0, Src IP addr: 192.168.230.162
    Addresses bound to peer TDP Ident:
    192.168.100.17 192.168.100.25 159.107.212.49 172.16.8.81
    192.168.230.130 192.168.230.77 192.168.230.81 192.168.254.1
    192.168.210.6 192.168.127.6 192.168.210.106 192.168.127.66
    192.168.127.138 192.168.210.146 192.168.210.142 192.168.210.122
    192.168.210.17 192.168.230.140 192.168.230.26 192.168.230.74
    192.168.230.10 192.168.230.14 192.168.127.130 192.168.127.142
    192.168.230.6 192.168.230.70 192.168.230.34 192.168.210.178
    192.168.200.25 192.168.210.126 192.168.232.1 192.168.231.1
    192.168.200.17 192.168.210.102 190.168.200.245 190.168.200.225
    190.168.201.241 192.168.230.98 192.168.210.14 190.168.201.201
    190.168.201.209 192.168.210.162 192.168.210.210 190.168.201.205
    192.168.230.38 190.168.200.249 190.168.200.217 190.168.200.253
    192.168.230.162
    cnibhco112#
    cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
    Local Outgoing Prefix Bytes tag Outgoing Next Hop
    tag tag or VC or Tunnel Id switched interface
    cnibhco112#traceroute 192.168.254.1
    Type escape sequence to abort.
    Tracing the route to 192.168.254.1
    1 192.168.230.162 0 msec 0 msec *
    cnibhco112#traceroute 192.168.230.162
    Type escape sequence to abort.
    Tracing the route to 192.168.230.162
    1 192.168.230.162 0 msec 0 msec *
    cnibhco112#

    Ro,
    Thanks for the respone, have been playin, with MPLS for last few hours.
    The routing between the loopbacks is now working, can PING 7609 Loopback from AS5350 ,and vice versa. (used static routes).
    Having problem with TDP / LDP on routers,
    mpls label protocol ldp / tdp command works correctly on both routers, but the
    tag-switching tdp router-id Loopback0 force
    command works on the 7609, but when I add it onto the AS5350 , the command "mpls ldp router-id Loopback0 force" appears on the startup script.
    The opposite is true for the 7609 , you add MPLS LDP command, and TAG-SWITCHING command appears instead.
    Any Ideas, as different configs of this leave me with forwarding table with both tags added, but not been able to ping the loopbacks !!!
    When I can ping bot loopbacks, the OUTGOING TAG , disapears.....
    Problem is LOOPBACK Commands on bot routers default to LDP (AS5350) , or TDP (7609). Any Ideas ...
    mpls label protocol tdp
    tag-switching tdp router-id Loopback0 force
    mpls label protocol tdp
    mpls ldp router-id Loopback0 force
    cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
    Local Outgoing Prefix Bytes tag Outgoing Next Ho
    tag tag or VC or Tunnel Id switched interface
    18 17 192.168.254.0/24 0 Gi3/12 192.168.2
    MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
    00097CA3293000127FCDBA808847 00011000
    No output feature configured
    Per-packet load-sharing
    cnibhco100#traceroute 192.168.254.2
    Type escape sequence to abort.
    Tracing the route to 192.168.254.2
    1 192.168.230.161 [MPLS: Label 17 Exp 0] 0 msec 0 msec 0 msec
    2 192.168.230.162 0 msec 0 msec 0 msec
    But no PINGING 192.168.254.2
    cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
    Local Outgoing Prefix Bytes tag Outgoing Next Hop
    tag tag or VC or Tunnel Id switched interface
    17 18 192.168.254.0/24 1915668 Fa0/0 192.168.230.162
    MAC/Encaps=14/18, MRU=1500, Tag Stack{18}
    00127FCDBA8000097CA329308847 00012000
    No output feature configured
    Per-packet load-sharing
    cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
    Local Outgoing Prefix Bytes tag Outgoing Next Ho
    tag tag or VC or Tunnel Id switched interface
    18 17 192.168.254.0/24 752551 Gi3/12 192.168.2
    MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
    00097CA3293000127FCDBA808847 00011000
    No output feature configured
    Per-packet load-sharing
    WHEN BOTH LOCAL AND OUTGOING TAG, CANNOT PING EITHER WAY !!!
    HAVE LABEL PROTOCOL AND LOOPBACK FORCE on AS5350
    HAVE LABEL PROTOCOL ON 7609
    WHEN ADD LOOPBACK FORCE on 7609 , CAN PING BOTH LOOPBACKS,
    BUT OUTGOING TAG DISAPEARS
    cnibhco112#PING 192.168.254.2
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 192.168.254.2, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
    cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
    Local Outgoing Prefix Bytes tag Outgoing Next Hop
    tag tag or VC or Tunnel Id switched interface
    17 Untagged 192.168.254.0/24 598678 Fa0/0 192.168.230.162
    MAC/Encaps=0/0, MRU=1504, Tag Stack{}
    No output feature configured
    Per-packet load-sharing
    cnibhco112#
    mpls label protocol tdp
    tag-switching tdp router-id Loopback0 force

Maybe you are looking for

  • Archiving old TM files--new TM disk

    I'm moving my TM setup to an NAS drive. I originally wanted to use the NAS for iTunes, but that was too problematic and I discovered you can't back up an NAS drive to TM. So, I'm moving my iTunes folder to my old TM drive (USB external) and using the

  • Business rules

    Hi all, I developed a program in which it take a PO input and return whether approval is required or not. During this process, Il used a decision service to actually run through the rules defined in the dictionary. I created a Rules Dictionary ,and u

  • HT5100 Can i have back my money for purchased Apps wich not working correctly ???  thnx

    THIS APPLICATION NOT WORKING PROPERLY, LIKE IS WRITTE ON MANUAL AND I JUST WAIST MY MONEY.  CAN I HAVE MY MONEY BACK ???   MANY THNX FOR ANSWER.

  • PP1.1 for O2 branded N8??

    Is PP1.1 available in the UK? Every time I try to update I get the message from Nokia's download site saying no updates available. Solved! Go to Solution.

  • Help my MAC os 10.4 Tiger will not turn on

    I have been having problems with it not turning on, but if I would let it rest it would eventually turn on. Now nothing is happening. Has it died? This computer is only 3 years old. Is there anything I can do?