Problems to install GC over RH 64bits

Hi i was trying to install and that is my first time that's why i am sure that i am doing something wrong.
I installed a new rh5, downloaded all packages, libraries and my system is up to date to start a new GC installation
I downloaded 10.2.0.3 and 10.2.0.4 to start a new installation from here
http://www.oracle.com/technology/software/products/oem/htdocs/linuxx8664soft.html
I readed that to install 10.2.0.4 i must first install 10.2.0.3 and upgrade it
But when i unzip the 2 files from 10.2.0.3 i cant find runInstaller or something to make me start the installation.
I was reading and the steps says to excecute runInstaller like any oracle installation.
Ill continue searching but i dont understand what i am doing wrong
Thnx in advance

In 10204, oms is not supported on RH5.
To get the runInstaller you need to unzip the two file under the same dir. It will be under <stageloc>/disk1

Similar Messages

Problem with installing both 32 and 64bit Java7u45

Hi all.
For some reson we need to install Java7u45 because of an inhouse made application only runs on java7u45 32bit,
Now to my issue, we hava about 200 windows7 x64 machines who need both 32 and 64 bit java7u45.
If i install the 32bit the inhouse appliction works, but then other third party application will not run (SoapUI, Eclipse).
If i install both 64 and 32 bit the inhouse application will not run, i get this error message "NativeSwing[1]: Caused by: java.lang.UnsatisfiedLinkError: Cannot load 32-bit SWT libraries on 64-bit JVM"
In the Java Control Panel only the 64bit java shows up, and if i try to add javaw.exe from C:\program files (x86)\java\bin it will add the correct line, and i looks ok until i close the java control panel and open it, it will still only show the 64bit java.
So is there anyway to change the default 64bit java to 32bit and make it stick?
Thank you.

panosk wrote:
uwinkelvos wrote:This isn't GWT, is it?
Hi, is there anybody using Eclipse and GWT in arch 64?
I use Eclipse Galileo 64 bit and trying to use GWT I get the error "...wrong ELF class: ELFCLASS32 (Possible cause: architecture word width mismatch)..."
Should I nstall bin32-jre from AUR and use it to start a 32 bit version of Eclipse? Is there another way using the 64 bit version of eclipse?

Problems with installing Apps over 3G (iPhone OS 3.0)

Since the new OS 3.0 update I've been having some recurring issues when installing applications.
I go to the App store and enter my password (or enter it once I've selected an app - this step makes no difference)
The App starts loading.
Here is where the problem occurs, once it gets to about half way, it goes back to the beginning and starts again.
For some apps it might do this 10 times before it starts installing.
For other apps it simply says after 10 tries or so "Could not download application".
Basically the bar stops just before it normally changes to status text to "installing".
This is frustrating because I have excellent 3G reception with DL speeds of close to 300Kbps and this is eating into my quota. Especially so when doing 8 or so updates.
When I connect it to WiFi I don't seem to have this problem anymore.
This never used to happen before and only since the 3.0 update is it occurring. It makes me very reluctant to run updates or download apps. Updates essentially cripple my apps if they do not complete in some instances.
Has anyone else come across this and if so is there any solution other than some hack job?

hey,
im having the same problem too, at first i was thinking it was just my phone, but no it is still happening
anyway, i went into the Apple store today, and explained what was happening. The dude at the bar told me it is a known issue with Optus. Dam optus. i still dont really believe it tho, so i am going to try a different networks sim in my phone tomorrow and see if it makes any difference.

Problems with installing leopard over snow leopard

Have a Leopard store bought DVD and want to use it to install over a current install of Snow Leopard, 10.6.2 - but when I use the installer, and the machine re-boots to run the install, the screen is just grey and blank, forever. Any ideas?

You can't downgrade a system this way. The only way to downgrade is to do a full backup and then and Erase and Install. And if the machine is a new one which came with Snow leopard installed, you can't downgrade to an earlier system by any method: the hardware won't handle it.

I am installing itunes to a laptop and have not sync device to this lap. It is saying that it must first restore device. The problem is I have over 2000 pictures and don't want to lose them. Now my phone is in restore mode and I don't know what to do. I

I am installing itunes to a laptop and have not sync device to this lap. It is saying that it must first restore device. The problem is I have over 2000 pictures and don't want to lose them. Now my phone is in restore mode and I don't know what to do. I don't want to proceed and loose these very important photos of family. What do I do to get it out of restore mode? My phone will not allow me to do anything to it at this point. I have the itunes downloaded on the laptop now. When I push the button for the phone it just shows Itunes and plug. I can't even call or open phone up.

Unfortunately... Once the Device is asking to be Restored with iTunes... it is too late to save anything...
See Here > http://support.apple.com/kb/HT1808
However... Once you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766
Jessica Sanchez wrote:
I am installing itunes to a laptop and have not sync device to this lap. ...
Using a computer, other than the one you have regularily been Syncing and Backing up to, was the begining of your issue.

Hello, I have problems to install Flash Player in OS X Yosemite 10.10. Installation doesn't go on over 25%. What should i do??

Hello, I have problems to install Flash Player in OS X Yosemite 10.10. Installation doesn't go on over 25%. What should i do??

Try what klaush67354338 suggests. I had the same problem and his workaround worked perfectly for me.

Problem installing itunes on windows 64bit

problem installing itunes on windows 64bit, help me!!!

Yes, when I try to install the iTunes software on my notebook, running Windows 7 64-bit, I get a window that says: "There were errors before iTunes could be configured. Error during installation. Computer was not changed. "thanks

Install Windows 8.1 64bit on a Macbook Pro Late 2008 (using bootcamp 4.0.4033)

Hi everyone, I just tried to install windows 8.1 64bit (x64) on my MacBook Pro 15'' Late 2008 (Core 2 Duo 2.4Ghz - 4GB RAM - Nvidia 9600M GT 512Mo), running Mavericks (10.9.5), and successed it with bootcamp 4.0.4033.
I installed it from scratch (new partition, no update from windows 7), in less than 1h following these very simple steps :
Step "0" :
- You'll need an two-button usb mouse plugged
- Make sure your 64bit kernel is activated by typing this line of command in the terminal :
sudo systemsetup -setkernelbootarchitecture x86_64
If you need to cancel it, simply type this :
sudo systemsetup -setkernelbootarchitecture i386
I don't really know if this activation is necessary, but I did it 6 months ago for After Effects and maybe this activation has an effect on what happens next.
Step 1 : download the contents of bootcamp 4.0.4033 on a USB key, downloadable here : Boot Camp Support Software 4.0.4033
After the download, you'll need to unzip this file in your usb key.
NB : This bootcamp only works from XP to windows 7, but it will be enough for your old-timer laptop.
Step 2 : Create a new NTFS partition on your HDD (using the disk utility)
Windows 8.1 64 bit needs at least 20GB, so I recommend a 100GB partition as a minimum for a correct running OS (the "15%" rule).
NB : Windows 8.1 will run over a NTFS partition and nothing else.
Step 3 : Insert your bootable windows 64bit 8.1 (CD or USB key).
Step 4 : Reboot your laptop, and keep pressed the Alt key just after the boot bell sound.
The OS selection screen loads. Once appeared, you can release the Alt key.
Step 5 : If your bootable device is working, the OS selection screen will display a "Windows 8.1" HDD or CD icon. Click on it and presse "enter".
Maybe you'll see a "UFI Windows" or "UFI Boot" or "UFI something...", this doesn't work.
After pressing "enter", the windows 8.1 installation process will start.
Step 6 : During the installation process, you'll have to chose the destination partition for your OS.
Select the partition you've created earlier (step 2)
Following the windows 8.1 steps are very simple.
NB : Don't forget to press the Alt key when windows 8.1 tries to restart!
Step 7 : Eject your windows 8.1 CD/usb key, then reboot holding Alt key, and select your freshly installed windows OS in the selection screen
Step 8 : After windows 8.1 is loaded, insert your usb key with Bootcamp 4.0.4033, open the "bootcamp" folder, right-click on the bootcamp setup, and click on "properties".
Select the "compatibility" tab
Check the box "run this program in compatibility mode for"
In the list below this box, select "Windows 7"
Click "Apply" then "Ok"
Now launch this boot camp setup (press "enter" or double-click)
Step 9 : Complete the BootCamp installation process, then restart (like step 7)
Don't forget to hold the Alt key after the bell sound
Step 10 : Enjoy your freshly installed windows 8.1!
You can acces your bootcamp parameters from the task bar (click on the tiny booycamp icon to open the quick menu and then click on the parameters/configurater). Here you can set your keyboard preference, your trackpad preference (multi-touch works), etc.
Following this procedure, I can use the built-in Apple-maped keyboard of my MBP. Every function keys works (Volume, luminosity, etc.)
Coming from Windows XPSP3, I was very surprised by the speed of the windows 8.1 installation (using an external USB super drive), and more surprised by this OS running flawlessly on my undying MBP!
The only issue I have is that my ethernet port isn't recognized, but it's a minor problem and i'm gonna found it quickly. I think it's due to my installation which wasn't perfectly clean (I try to run manually bootcamp 5.0.1 first, so there is some crap drivers somewhere).
So in order to confirm this procedure, i'm gonna re-install windows 8.1 from scratch very soon, because it take less time to do it (from step 1 to step 10) than write this article!
Message was edited by: Lud@l

And I used this method:
1. Install Windows 8.1
2. Download BootCamp 5 and unzip to folder BootCamp5 of a USB drive
3. Start CMD as Administrator
4. Install BootCamp 5 by entering the following commands
D: (Assuming the USB drive is assigned to letter D
CD BootCamp5\BootCamp\Drivers\Apple
BootCamp.msi
No need for InstEd might be considered by some as even more elegant as bezodziu's method

Problem with installing CUCM on MCS-7816-I5

Hi to all.
I have a problem with installing CUCM 8.6.1 on new MCS-7816-I5 (IBM) hardware. The problem is that installation loops in restart after upgrading MCS firmware. Actualy, installation does not sucessfully upgrade firmware, so every time it detects old firmware and trying to upgrade it.
I also tried update MCS firmware with downloaded Firmware Update Utility 3.6.5 CD from Cisco downloads, but it also fails.
Does anyone have idea what's going on? Is this a Cisco failure or IBM server failure?
Here is some details from log file generated with this Firmware Update Utility 3.6.5:
==============
Initial Selection
Machine Type: 4251 OS: SLES 10 Arch: 64 bit
IsPartition: 0
Update:   IBM System x uEFI update for x3200 M3 /3250 M3
Severity: Critical
Reboot:   Reboot Required to take effect
UpdateID: ibm_fw_uefi_gye142a_linux_32-64 Requisite:None
Version: 1.08 (GYE142A)
Install: 1.06 (GYE135A)
Select:    Yes
Update:   IBM Dynamic System Analysis
Severity: Recommended
Reboot:   Reboot Required to take effect
UpdateID: ibm_fw_dsa_3.20_dsyt75x_linux_32_64
Requisite:None
Version: 3.20 (DSYT75X)
Install: 3.01 (DSYT60K)
Select:    Yes
Update:   IBM Online SAS/SATA Hard Disk Drive Update Program
Severity: Critical
Reboot:   Not Required
UpdateID: ibm_fw_hdd_sas-1.08.01_linux_32-64
Requisite:None
Name:     WD2502ABYS-23B7A0 (/dev/sg0)
Version: 02.03B07
Install: 02.0
Select:    Yes
Update:   Integrated Management Module Update
Severity: Critical
Reboot:   Not Required
UpdateID: ibm_fw_imm_yuoo84c_linux_32-64 Requisite:None
Version: 1.22 (YUOO84C)
Install: 1.10 (YUOO57H)
Select:    Yes
IBM Command Line IMM Flash Update Utility v1.05.03 Licensed Materials - Property of IBM
(C) Copyright IBM Corp. 2009,2010 All Rights Reserved.
LAN-over-USB device not configured.
Error connecting to IMM using IP address 169.254.95.118.
Please verify the LAN over USB interface is configured properly and active.
Error flashing firmware: 3
IBM Command Line IMM Flash Update Utility v1.10.11 Licensed Materials - Property of IBM
(C) Copyright IBM Corp. 2009,2010 All Rights Reserved.
Refreshing LAN-over-USB IP address. This may take several minutes.
Attempting to discover the IMM(s) via SLP.
Error connecting to IMM using IP address 169.254.95.118.
Please verify the LAN over USB interface is configured properly and active.
Error flashing firmware: 10
(C) Copyright IBM Corp.2010. All Rights Reserved.
FdrvWL -- Flash Drive(s)                                     3.10.08.19
   1 Ada:0 SID:0   PN:44E9172:42C0463 SN:1J242783 FW:02.03B07              T:13 FW:Ok
AdaNbr(Type)      DevFnd Flashed(SAS SATA) NbrFailed
0(onBoard)           1       0   0    0          0
                       1       0   0    0          0 Error(s)
Update completed successfully. <-- THIS SUCCESS, BUT EVERY TIME IT UPGRADEING AGAIN FROM OLD VERSION, LIKE NEVER REALY UPGRADED TO NEWER VERSION
IBM Command Line IMM Flash Update Utility v1.10.11 Licensed Materials - Property of IBM
(C) Copyright IBM Corp. 2009,2010 All Rights Reserved.
Refreshing LAN-over-USB IP address. This may take several minutes.
Attempting to discover the IMM(s) via SLP.
Error connecting to IMM using IP address 169.254.95.118.
Please verify the LAN over USB interface is configured properly and active.
Error flashing firmware: 10
===========================
Thanks,
Sinisa.

Hi Sinisa,
It almost sounds like this bug;
CSCtn81201
Incorrect "Hardware Configuration Error" due to hardware setup errors
Symptom:
Refresh upgrade stops with IMM device detection, and then server being reported as unsupported
Conditions:
in-band USB interface was disabled, which is configurable via IBM system X or IMM (browser) interfaces.
Workaround:
change the in-band usb interface settings to enabled.
Related Bug
Status
Fixed
Severity
4 - minor
Last Modified
Aug 17,2011
Product
Cisco Unified Communications Manager (CallManager)
Platform
Dependent
Technology
nav
1st Found-in
8.6(0.99081.3)
Fixed-in
8.6(1.96000.1), 9.0(0.95070.38), 9.0(0.95070.39), 8.6(1.99989.1), 8.6(1.95050.1), 9.0(0.96000.1), 8.6(1.97011.2), 8.6(1.95190.40), 8.6(1.97011.1), 8.6(0.95180.9), 9.0(0.95010.1), 8.6(1.95020.1), 8.6(1.95040.1), 8.6(0.98000.50), 8.6(0.98000.17), 8.6(0.99981.2), 8.6(1.10000.1), 8.6(1.99986.1), 8.6(1.95020.58), 8.6(1.96000.51), 8.6(1.10000.43)
Cheers!
Rob

Some issues after clean installing windows 7 pro 64bit

Hi,
I have a couple of issues, I clean installed windows 7 pro, 64bit, (vanilla) restored my license with ABR and used system update to download all the drivers. (no issues until here) But after restarting the system, I found this issues:
1. I have to put the bios in legacy mode for system to boot. Otherwise it gives me a "no operating system found" message. Is there any way to make a proper installation for the system to boot in UEFI and LEGACY?
2. System update didn't install thinkvantage center. (the program that stays in the taskbar). Should this be installed manually? Or system update should have installed it?
3*. I can not use lenovo driver page of my x120e. In IE it shows me repeatedly the wizard to choose my model, although I enter the correct info there. It starts all over again and again. Tried opera, I can see the drivers page, but I can't browse, or expand none of the sections. (all I can think of this, do I need java for the page to work?)
3*. UPDATE: After installing IE 9, java and flash player, still not working. Opera too. Google Chrome works fine. What's the matter with IE and OPERA? What component do I need to make IE work with lenovo drivers download page?
Can anyone help me? Never had to deal with these issues.
Thanks in advance
I'm just a volunteer. I like to help others where I can. Do my ideas work? I hope so. o_O
Who helped you today? Do not forget to thank him.
My hardware: TP x120e 0596-2ru. Windows 7, sp1, 64Bit, English, installed in UEFI mode.

Hello,
Have you tried wiping the hard disk drive and reinstalling Windows 7 Professional x64 from the factory recovery discs while the BIOS is set to UEFI? If so, did that work?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

HP C309 G AIO can't install in Windows 7 64bit running under BootCamp

HP C309 G Printer wont install in Windows 7 64bit running under BootCamp on a new iMac
Just bought a new iMac. Installed HP C309 all in one without incident on the Mac side. I am also running Windows 7 on iMac through a program called Bootcamp. When I boot to Windows 7 and try to install the newly downloaded software for windows 7 from the HP site, it begins to load then stops, giving me two error messages. They are both essentially the same except one says software and the other says hardware. The software one says: This computer does not have the necessary USB software support to allow completion of a USB installation. The printer plugs directly into the monitor in one of four usb ports. All the usb ports work on the system when using Windows 7. I have other devices working and plugged into the usb ports while in Windows 7. It is almost like the printer software is unable to find the usb software or hardware. Any ideas

Well, you have a full Window's 7 install so you would really have to go to HP and/or Microsoft to see what is going on. Bootcamp basically is only involved with "booting" and just installs Apple product drivers and such. Just treat the Window's side as if you are using it on a "normal" Window's PC. (As far as problems, crash's, updates, or any other Windows, HP, etc, problems you may have.)
"Installed HP C309 all in one without incident on the Mac side."
So,,, that means the printer "works" (prints) on the Mac or the installer just worked? Make sure the Printer actually prints in the Mac side as you may have a dead USB port on the Printer. It happens.
If your HP works fine (prints) in the Apple environment you know it's not the USB ports on either the printer or the computer.
You said you already downloaded the newer versions, have you tried using the drivers on the install disk and then update them to the newer ones? Also if you haven't yet, make sure the drivers are for the 64bit version, just a thought.
That's about all my brain cells have so good luck.......

Unable to install windows 8 Pro (64bit) on R61, 7755jm1

I have an old thinkpad, the R61 series, model 7755JM1.
And I tried to install windows 8 pro (64bit) on it, hoping to have a taste of the new OS's touch features through remote control on my tablet.
However, the installation has never been successful.
I was able to finish the installation process. Yet whenever it starts to "setup my device", it was never able to finish, and it usually stopped at 65% or 84%.
then my thinkpad would restart on its own, and threw an error message telling me my computer is restarted unexpectedly and the installation is not succeful, also suggesting me try to install again.
This is very frustrating. I have checked on intel's website and other online sites that my CPU (core 2 dual process T8100) supports intel64, and execute disable bit (in my BIOS I think it is by name of "execution prevention"), and sse2, sse3.
In my BIOS, I enabled execution prevention, set SATA mode to "AHCI", and enabled "extended memory test". I format the partition every time I tried to install.
I have installed windows 7 pro on my thinkpad before, and it was just fine.
Do anybody have any idea what is going and how should I solve this?
Many thanks.
Lee.

Hello,
According to the Lenovo, the specs for your R61 (MT: 7755-JM1) as it shipped are as follows:
T8100(2.1GHz), 1GB RAM, 160GB 5400rpm HD, 14.1in 1400x900 , 128MB nVIDIA Quadro NVS 140M, CDRW/DVDRW, Intel 802.11agn wireless, Bluetooth, Modem, 1Gb Ether, UltraNav, Sec Chip, FPR, Camera, 4c Li-Ion, WinVista Home Basic 32.
As you pointed out, the T8100 is a 64-bit CPU, so there should be no problems with that. I did notice that the unit originally shipped with 1GB of RAM, though.
From looking at Microsoft's Windows 8 System Requirements page, I see that 2GB of RAM are required for the 64-bit edition of Microsoft Windows 8, so if your R61 only has the original 1GB of RAM in it, it will need to be upgraded..
The R61 officially supports 4GB of RAM in the form of two 1GB PC2-6400 800MHz DDR SO-DIMM modules, and apparently can unofficially be upgraded to 8GB using two 4GB modules with the same characteristics.
If you already have 2GB (or more) of RAM installed, the other suggestion off the top of my head is to make sure you have the latest version of the BIOS firmware installed:
Name: BIOS Update Bootable CD for Windows 7 (32-bit, 64-bit), Vista (32-bit, 64-bit), XP, 2000 - ThinkPad R61, R61i 14.1 inch widescreen with IEEE 1394, ThinkPad T61, T61p
URL: http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS013943
Version: 2.30-1.08
Released: 02 Apr 2012
If the issue still occurs, please let us know and we can try and help you troubleshoot it further.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

I met problem when installing Oracle 8.1.6 on Turbo Linux 7.0

I met problem when installing Oracle 8.1.6 on Turbo Linux 7.0.
After setting up environment variables, and successfully
accessed KDE interface, everything was going on well.
The process of installation blocked at 80% in "Database Creation
Process" dialog window.
I have tried two times and got the same result.
The error message is:
Warning: Cannot convert string "-*-Kochi Gothic-medium-r-normal-
*-*100...
Help!

I have done some oracle installations over RedHat 7.0 (not certificated):
Let's check some things:
1- You must have changed very few parameters on your shm.h sem.h files which are in /usr/include/linux directory.
2- You need to upgrade the glibc and libstdc libraries (.rpm)
3- You must have installed the jre116_v5 on /usr/jre and made a symbolic link like this
ln -s /usr/jre/jre116_v5 /usr/local/jre
4- You must include in the CLASSPATH parameter the jre116_v5 directory. It should look something like this
CLASSPATH=/usr/jre/jre116_v5:$ORACLE_HOME/jlib
5- Be sure to create and export all the parameters in your .bash_profile.
6- Run the ./runInstaller.sh in a terminal window inside the Xwindow.
You can find the jre116_v5 in www.backdown.org
I hope these tips help you
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by xx:
Hi every body
when I run ./runInstaller from cdrom
I get this messages :
Initializing Java Virtual Machine from /usr/local/jre/bin/jre.Please wait ...
Error in CreateOUIProcess ():-1
: Bad Address
I use JDK-1-1-6.
Thx<HR></BLOCKQUOTE>
null

Problems to install OS X Lion

I just buy on app store the new OS X lion and im having problems to install it on my mac book air.
Someone can help me ?
When i follow the instruction it stop on the windows saying " selected the disque" but i can't select anyone , i don't undersand i have free space on my mac
( 8 GO )
Thanks for your help
Co

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Select "/var/log/install.log" from the file list. Post the messages from the last installation or update attempt, starting from the time when you initiated it. If you're not sure when that was, start over and note the time.
Post the log text, please, not a screenshot. If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into a message.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting.

OS X wouldn't install after accidentally installing Windows over it

My sister attempted to install Windows XP on her Macbook Pro using boot camp but some how accidentally installed Windows over OS X. I used Disk Utility to erase the drive and reformat it back to "Mac OS Extended (Journaled)" but I get the following error when trying to install OS X:
+"Install Failed+
+Mac OS X could not be installed on your computer+
+The Installer cannot prepare the volume for installation. You may need to prepare your disk using Disk Utility.+
+Click Restart to restart your computer and try installing again."+
Am I doing something wrong? Is there a problem setting or hardware wise?

Welcome to Apple Discussions:
In addition to formatting, you need to be sure the disk is partitioned GUID for an Intel machine.
Boot into Leopard DVD and run disk utility again and repartition it and format it at the same time. Because of the bootcamp issue, you might be better making two partitions first and then making one to be sure that the entire disk has a single GUID/HFS+ partition/format scheme.

Problems to install GC over RH 64bits

Similar Messages

Maybe you are looking for