Problems trying to extend my network using an Airport Express

HI
I have a Cisco Cable Router with Wifi (EPC 3825) but the range reach is too short and need to extend my Wifi in order to cover some areas.
therefore I bought a AE in order to install them in differents areas of the house..
The problem is the following one.
I connect the AE directly to my MBP using an ethernet cable, I start configuring the AE as "extend my network using Ethernet" finish the configuration of the AE then update. it reboot and then the LED is slowly blinking yellow. then I connect it to the Cisco Router using a standart Ethernet cable.
but the AE remains with a yellow light and I can’t even see it using the Airport Utility.
I did the same with the second AE with same result.
I don’t know if the problem comes from the fact that the Cisco Router creates the network and both the AE extends the ntw. maybe it is expected that the creation of the ntw has to be done by an apple devices.
Can anyone help?
thanks a lot in advance.

Ok, thanks for clarifying that you will have all of the base stations connected back to the Cisco router by Ethernet. In this case, you will want to reconfigure each of the AirPorts for a roaming network.
Roaming Network Setup
Ref: See page 42 of the Apple AirPort Networks guide.
Setup each AirPort, as a bridge. Internet > Internet Connection > Connection Sharing: Off (Bridge Mode)
For each AirPort:
Connect it back to the Cisco router by Ethernet.
Provide a unique Base Station Name.
The Network Name (SSID) should be identical to that used by the Cisco.
If using security, use the same security type (WEP, WPA, etc.) and password. Note: It is highly recommended that you use WPA2 Personal for best bandwidth performance.
Make sure that the Radio channel is set at least three channels apart from the next base station to prevent Wi-Fi interference.

Similar Messages

Extending an Network Using Powerlines & Airport Express

Apologies for the rather long winded question - however I am hoping that there is a fairly simple response.
I have just moved into a new house with very thick walls. The wifi signal (from a BT HomeHub (2??)) router makes it around the majority of the house - except the dining room where we plan on using the macbook the most.
I thought i could solve this problem by buying a Belkin Powerline and an Airport Express. The ultimate aim is to use the Airport Express both as Airtunes device and also as a device to extend the wireless network in the dining room.
My current set up therefore is the phone line connected to the BT router; router connected to the powerline socket via an ethernet cable. In my dining room (where there is no wireless signal) I have the other powerline socket connected to my Airport Express. Having gone through the set up process, Airtunes works well, broadcasting from the mac to my stereo via Airtunes. However it is clear that i am unable to connect to the internet using the mac in my dining room - suggesting that the Airport express is not extending the wifi signal (if i plug the macbook into the powerline socket directly using the ethernet cable then the internet works fine).
My question therefore is, given the above device set up, how can do i set up my Airport Express so that I can connect to the internet AND use Airtunes in a room that is outside the range of the BT base station, but is connected to the internet via a Powerline?? Ideally the wi-fi signal provided by the Airport Express would be the same as provided by the BT Box so that I can wander round the house picking up whichever source is the strongest. Is this possible??
thanks in advance and apologies again for the long winded question!
many thanks
Paul

Hi can someone help me please....... I am new to this and as such couldnt even find out how to post a new thread..... sorry i am not into IT thats why I buy apple cos I dont normally have to think : )
Here is my issue. I ahve just moved back to the UK and into my old house, I have a BT homehub installed as they were easiest and fastest to get online with, the airpot in my Imac works fine with it and within twenty feet everything esle connects fine too, my issue is my apple tv simply cannot find the network, I have tried extending the range with everything, Belkin etc and then someone suggested airport express. Nothing seems to work but at least airport express tells you why and apparently the why is because my homehub will not let its network be extended ? BT now tell me that this is true !!!! now I am stuck in a contract with BT with a homehub that doesnt reach my apple tv that cannot be extended by airport express ? is this really true or can someone help me please, please . I have read the post above and just want to know if the airport express needs to remain pluggedinto the router via ethernet ?? if so it is unlikely I can have the airport express unit much more than a few feet away from the homehub and if so how will this increase the overall range of the network ? over the existing home hub ? frustratingly my apple tv etc is the furthest possible point away from the hub and with several thick stone walls in the way which is obviously why I am having issues ? making the airport express a repeater in a mid point would be ideal but apparently this is not possible ?

Trouble extending wireless network using 2 Airport Expresses

I used to have one Airport Express extending my Time Capsule, and had a stable network. Since adding a second Express I have intermittent prroblems - sometimes termporarily "losing" the network from my devices (Mac Mini, iPhones, iPads) at various parts of the apartment. I absolutely can no longer use Time Machine to back up my Mac Mini from the second Express to the TC (a full backup estimated 5 days and keeps timing out or failing).
There's quite a bit of degradation in the signal from the front of the apartment (the TC) to the back (the 2nd Express). For example, at the TC attached to the cable modem, I get about 20-25 Mbps download (very happy) and in the back where my computers now are, I get about 2 Mbps (unliveable - really).
I need it to be stable, but sure hope I can get better performance. Can anyone help me troubleshoot or tune up the performance?
Are these Expresses phasing each other in and out?
My configuration:
Living room: Time Capsule (1st generation) running 802.11n 2.4GHz only network. Firmware version 7.6.1
Next in line, about 35 feet away, Airport Express, FW Version 7.6.1
Last in chain, another 35 feet away, Airport Express, FW Verson 7.6.1
I live in a 1,600 sq ft apartment, not a huge house. There are some walls, but I try to keep them pretty exposed.
I set it up using Apple's Airport Utility v 6.1 (610.31), from Mac Mini using Lion 10.7.4
Default settings, no tricks, DHCP. Just turned off Airplay to see if that would help.
Airport Utility says (today) I have "excellent" connections between the devices.
Any help would be grealy appreciated.
Jim

Next in line, about 35 feet away, Airport Express, FW Version 7.6.1
Last in chain, another 35 feet away, Airport Express, FW Verson 7.6.1
The "remote" devices in Apple's "Extend a wireless network" setup all connect directly to the main router...in this case, it would be the Time Capsule.
The setup works like the hub and spokes of a wheel. The Time Capsule would be the hub and each AirPort Express resides at the end of a spoke. A device at the end of a spoke cannot communicate with another device at the end of another spoke. It communicates directly to the Time Capsule.
Remember that an "extending" device can only extend the bandwidth (speed) of the signal that it receives. It can help provide more signal strength.....but it cannot make the signal that it receives go faster. Placement is critical.
If you had only one Express, a good location might be approximately half the distance from the Time Capsule to the general area that needs more wireless coverage.
Chances are, the second Express is receiving such a weak (and slow) signal, that it cannot do anything to help. It is like a copy machine trying to copy a very poor image. You may well be better off eliminating the most distant Express and trying things that way.
Things get more complicated when you add in obstructions like walls. Even a typical interior sheetrock wall will absorb 15-20% of the signal or more, so after a few walls the signal has already lost approximately half of the strength...and speed.

How can i extend my network using an airport express

I have an airport express that connects wirelessly to an airport extreme. I would like to use it to extend my network. It has a strong signal coming in to it from my extreme. It works fine when I try to connect to the network, but it dies completely when I try to use it to extend my network. After going through a restart, it disappears from the network. The only way to bring it back to life is to unplug it, let it rest a few seconds, plut it in again, and then reset it to Connect to the Network before it crashes again.
I have a model of the express that is supposed to work with extending the network.
Thanks for any suggestions.

I would recommend that you configure your extended network by first placing the Express in the same room as the Extreme. Once the extended configuration is verified, you can take the Express to the desired location.
The key to extending a wireless network with decent overall bandwidth performance is the proper placement of the extending base station. Please check out the following AirPort User Tip for details.

Extending My network with three Airport Express or buy an Airport Extreme?

I live in a large three story house and currently have it wirelessly networked using two Airport Express' but my signal is very weak on the third floor and in other spots throughout the house.
Would it be possible to buy a third AE and extend the network that way or would I be better off buying a AEBS?
Any thoughts or suggestions would be greatly appreciated.
Thanks

It will really depend on the construction materials used in your house or any other forms of Wi-Fi interference that could prevent a clear wireless signal. Both routes, you suggested, will have it advantages and disadvantages.
Extending the existing network wirelessly using a WDS, effectively, cuts the throughput in half for each base station in the chain...so, in this case the second AirPort Express Base Station (AX) (acting as a WDS relay base station) would only get half that of the first AX (acting as the WDS main base station). In turn, the third AX (acting as the WDS remote base station) would receive half of the second's throughput. The good news is that you should have a strong signal across each of the AXs, just lower throughput the farther along in the chain.
The 802.11n AirPort Extreme Base Station (AEBSn) has a greater range than either the older 802.11g version or the AXs. You may find that it will provide enough to cover you entire house. In the off-chance that it doesn't, you can still use it to create a WDS between AEBSn and your current AXs.

Extending a network with 2x Airport Express

I tried searching and couldn't find any discussions which answered my question. We have a home office which was just completed (an actual, separate structure, not just a room) and I need to connect it to the main house where our Internet connection comes in. What I'm trying to do is use an Airport Express (802.11n), which wirelessly connects to the main router, an Airport Extreme (802.11n, 2nd gen.). This Airport Express is then connected via Cat5e cable and a gigabit switch (it's a pretty long run) to another Airport Express (802.11n). This second Airport Express will then reconvert the connection to wireless and allow us to connect our devices in the office to the rest of the network and get access to the Internet.
Here's a crappy diagram I drew in Paint: http://i.imgur.com/5KrhX.png
When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet. Once I try to commit the changes, though, the device restarts and ends up with a blinking orange light, disappearing entirely from the list of devices in Airport Utility.
I've checked and the Airport Extreme is set up to allow devices to extend the network, and I've tried setting the first Airport Express to both "Join my wireless network" and "Extend my wireless network," though neither seems to make a difference.
Am I missing something, or trying something that won't work? Any ideas?
Thanks!

When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet.
You have two choices with AirPort Express #1:
Configure the AX as a wireless Ethernet bridge. Apple calls this configuration a ProxySTA. In this configuration, the AX would join the wireless network provided by the AirPort Extreme, and then, share this connection out it Ethernet port to the Ethernet switch.
Configure the AX to extend the wireless network of the AirPort Extreme. This would also enable the base station's Ethernet port.
Of the two, I would recommend the first option.
To configure the AX as a ProxySTA, you need just to make the following two setting changes:
Wireless Mode = Join a wireless network
Allow Ethernet clients (enabled)
Both of these settings are on the Wireless tab in the AirPort Utility.

How do i extend my network with a airport express

How do I extend my network with mt airport express

Hi Tesserax, I'd like to join this discussion. It seems Jasonbeyer didn't reply, but I have a question related to his.
I'd like to extend the wireless signal from my Cisco Model DPC/EPC2202 VoIP Cable Modem (802.11n) to the living room where, at the moment, it is non-existent. I assume there's inteference or the signal cannot reach through the concrete walls and rooms leading up from my bedroom to the living room.
My question is:
I'm thinking of extending my wi-fi signal by using the Airport Express and simultaneously using it to connect to my hi-fi to play iTunes from my bedroom's iMac.
Something's telling me it's not going to be that easy. I'm using an iMac (7,1) if that's any help or clue.
What are the things I should take note of and will Airport Express be compatible with my modem? Would I have to get TWO Aiport Express to bridge the signal to my living room?
Thank you everyone for your time. Cheers!
Kane

What kind of range extender can I use with airport express

WHat kind of range extender can I use with an airport express?

WHat kind of range extender can I use with an airport express?
Use any router that you want if you will be connecting the extender/router back to the AirPort Express using a permanent, wired Ethernet cable connection.
If you are planning to use a wireless connection to extend the range of the network.....then another AirPort Express, AirPort Extreme or Time Capsule will be required.

Creating a wireless network using several Airport Express(es)

I would like to connect three AirPort expresses to my Sky Broadband router to create a new wifi network in my house. My router is in the basement and is connected into a hub which provides ethernet to the house. I would like to connect the AirPorts via ethernet to the router and create a single wifi network.
Can someone please tell me if this is possible and what settings the AirPorts should have. For instance, should I just extend the sky network using each AirPort or should I create a new network with one AirPort and then extend that with the others?
Many thanks
Terry

If each of the AirPort Express devices will be connected using Ethernet, you would configure them all exactly the same except for assigning different device names...AX1, AX2, AX3, etc.
Each Express will be configured to....
Create a wireless network
Same wireless network name on all devices
Same Radio Mode
Channel set at Automatic
Same wireless security setting
Same wireless network password
Very important....configure each Express in Bridge Mode
Post back if you need more details

Trying to extend my Airport Extreme network using two Airport Express

Ok, so just an hour ago I had a network working fine that was set up like this:
Modem => Airport Extreme => Airport Express 1 / Airport Express 2
Stupidly I decided to rename one of them, to their specific room location, using Airport Utility 6.3.2, after it came back online it was listed on the utility bliinking yellow, when I hover over it with the mouse I can see the YELLOW DOT next to STATUS: Extend network, if i click on that it gives me the option to A) IGNORE B) EDIT and futher it goes on to say that it CAN NOT EXTEND THE NETWORK, asking me to check if the device is configure correctly/password is correct/or within range.
I have tried everything, reset, factory reset, setting it up again, and it just comes back blinking yellow.
Stupid again: I decided to unplug the other Airport Express, to see if that would help bringing the first one online again, now I have TWO yellow - non-able-to-extend-range Airport express units in the house.
Naturally I am quite frustrated, so any good advice will be very much appreciated, thanks!
The Airport Extreme is version 7.6.4 and serial number 6F8070MYYEW (If that helps anyone), both Airport Express is the latest version.

Hi Bob thanks!l
After about two hours of trying everything, I finally did something that fixed the issue, and since I have been around the block so many times I am actually not sure what it was; but it was a change in the setting on my Airport Extreme, and I think maybe I canged the router mode from DHCP (Is that default) to DHCP/NAT - and after that I was able to bring my Airport Express stations online again.... Weird, and far from the tunrkey solutions I have come to expect from Apple regarding internet connections.
Thanks for helping Bob, althogh I came up with a solution on my own, people trying to help is always very very much appreciated!!
Best
Eirik

HT4259 When I'm trying to extend my network using airport extream to airport express via LAN, the express is finding the network, then not completing and getting error message that it cannot connect, any advice appriciated

I'm using a virgin superhub, turned into modem only and connected airport extreme, wireless network setup and working
From the airport express I have a LAN to my office where Im trying to get a airport express setup as a extended wireless network
The express is finding the extreme device and network, it then won't connect and I get an error message "an unexpected error occurred. Try again"
Any help appriciated

From the airport express I have a LAN to my office
I'm confused, did you mean to say Extreme here instead?
What model #s are your routers?

Help! Im trying to extend the network on my Airport Extreme with an Express

This is probably such a begginers question but it has truely boggled my mind for the last 24 Hours!
I have brought an airport express to extend my airport extreme network. My Airport extreme is the base and is hooked up to my initial Home model from my ISP which works fine.
I have been trying to connect my airport express and am having no luck. I have plugged the airport in but am having no luck locating it on my airport utility (only my actual Airport Extreme shows)
Can someone please help me Ive been here for hours reading on forums trying to sort this out and Im gettin nowhere fast!
The light on the express is flashing orange. I have tried to reset it but there still is nothing showing.
any ideal on what i could do or follow step by step?

Ok, the question is how can i extend the range with
my airport extreme base,
With an Airport Express or another Airport Extreme
I have A netgear WNP802, it
has a repeating feature.
Which won't work with your Airport Extreme
< But i am wanting to have the
netgear and the apple airport extreme talk to each
other so that i can put the net gear in a seperate
room to extend the range of signal. </div>
This is not possible.
How can i do this?
You can't.
Netgear and Apple use different chips which means they won't and can't talk to each other when it comes to extending networks.

HT1515 extend a wireless network using my airport express

I bought an airport express back in 2006 with my macbook. I recently bought a time capsule and am now using it as my wireless router. Can I use my old airport express to extend / boost my wireless signal throughout my house? if so how?

Check the label on the side of the AirPort Express to see if the version that you have includes the feature to "extend" a wireless network.
If it does, you will see Model No A1264 there.
If you see A1088 or A1084, unfortunately this version of the Express does not have the ability to "extend" the wireless signal using wireless only.

HT4259 How to you extend my existing network using an AirPort Express?

My current configuration is a Linksys wireless router that I'm connecting to the AirPort Express via Cat. 5 cable. Only get a flashing yellow light. Help.

I got it working but here is the deal. It is not intuitive; you have to set it on "Create a wireless network", not "Extend a wireless network". You use extend a wireless network when you do it all wirelessly when the signal from the base is strong enough. But since I couldn't reach my wireless network to boost it, I had to use the cat. 5. So I guess it does make sense since I'm going from my WAN by cable to creating a wireless network. For some reason I thought it was going to be seamless with my existing wireless network so therefore I was extending my wireless network. Wrong. Thanks for all your suggestions as I think I would have quit long ago without you help.

Extend wireless network with multiple airport express and netgear powerline

I currently have the following network configuration:
1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
Thanks in advance!
Dave

I had a VERY similar problem: I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule. Every time I plugged in the wire to the TC, everything disappeared. Unplugged, and boom. Came back.
Here's how I solved it:
Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it. Then, on the wireless tab select CREATE a wireless network. But, give it the exact same name and password. This is completely counter-intuitive. You would think to choose EXTEND, but this would be wrong. Next choose the network tab. And, select Router mode to Bridge (off).
By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
See if this fixes your issue. Fixed mine instantly. AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out. LOL

Problems trying to extend my network using an Airport Express

Similar Messages

Maybe you are looking for