Problems with 802.11b networks

My MBP did not connect to my 802.11b home network as all my PCs do. So I upgraded to an 802.11g access point and now all the computers are talking to each other and the Internet.
But the MBP will not connect to ANY 802.11b network. I have tried several and no go!! All are unencrypted so no WEP issues. Am I missing something with the MBP or is there something wrong with the software. The configuration test window shows a strong signal and green indications for the top three lights (802.11b stuff) while turning red for the bottom three (actual connection related stuff).
I am a returning Mac user after 20 yrs with the PC, but this is very frustrating.
Thanks for your help

I've connected to 802.11b networks with no problem so it isn't a general problem.
I'm not clear on what software you are using. What software shows red and green status indicators?

Similar Messages

Airport Extreme Problems with 802.11b router

I have a Netgear MR314 LAN and wireless router. I have a G3 iMac and 2 G3 iBooks with Airport Express cards and they work fine with the wireless connection with this router. I have a 12 inch G4 iBook with an Airport Extreme card running 10.4.3. Every time when this iBook connects with the wireless router it works for about 10 minutes and then the router locks up. If I re-set my cable modem and the router then the system will work again.
Because the router only goes up to the speed of 802.11b and not the 802.11g potential speed of the Airport Extreme I know that the card has to run at the slower speed when it connects with my router.
I am trying to determine whether my Airport Extreme card is defective. Any suggestions?
iBook G4 1.2 GHz Mac OS X (10.4.3)

I have updated the firmware in the router and that seems to have fixed the problem.
ibook 12 Inch G4 1.2 GHz Mac OS X (10.4.4)

Aironet 1140N in mixed mode not working with 802.11b/g Clients

I have a new Aironet 1140N Access point , the model is number AIR-AP1142N-A-K9, my main problem in that i have Nokia E71 smartphones on the network, but they cannot connect to the Network, the Access Point SSID is not showing on the List of Available Devices if i Scan using the Phone,
All Laptops are runing Win 7 Pro and they connect quite ok, The phones (8 of them) at HotSpots connects without problems, the Spec says they are compatible with 802.11b/g and the Aironet Access point provides 802.11a/g/n.
Since the phone has the 802.11g which is compatible with the Access Point, why cant it Pick it? the Access Point is Operating in Mixed Mode.
Bonnie

There are basically two "flavors" of WDS that the AirPorts support: static & dynamic.
o A static WDS allows for a main, relay, and remote base stations in the configuration. This only operates in the 802.11g radio mode. Its advantage is it is well suited when you are trying to cover a considerable linear range ... like a rectangular house where the Internet connection comes in at one of the shorter sides and you want wireless at the other end. The biggest disadvantage of this type of WDS is that for every base station added, you lose half the overall bandwidth.
o A dynamic WDS allows for only a single main and multiple remotes. Think of a wheel with the main at the center and the remotes as spokes of the wheel. The advantage of this type of WDS is it operates in the 802.11n radio mode and doesn't suffer a significant bandwidth loss like the static version.
As a minimum, a dynamic WDS requires two 802.11n AirPorts (or Time Capsules). You can create a static WDS with either all 802.11g AirPorts or a mix of 802.11n & 802.11g AirPorts. Note; however, you cannot create a dynamic WDS with mixed mode base stations.

How to connect SPT 1700 to 802.11b network?

I know this is an old (obsolete by most standards) device, but still...
The ads for it that I have seen, claim that it is wireless capable with 802.11b abilities. I have looked through it, but I couldn't figure out how to set it up to access a wireless network.
Can someone, first of all, either confirm or deny the claim that it is 802.11b capable and, if so, how do I set it up?
Thanks...
Post relates to: Palm Pilot

Thanks Daniel,
I'll try the suggestion asap!
Filippo

AP with 802.11 G Vs clients with 802.11b

hi
i've got more access point 1200 series with he 802.11g but the client are 802.11b . Can the client 802.11b connect at the AP with 802.11 G ? Now i don't resolve this problem anche the client 802.11b connect only with the ap 1200 series with 802.11b
Thanks for all

> If you disable the "b" data rates, you've pretty much blocked "b" clients.
A-ha... As i can understand i must disable 1.0, 2.0, 5.5 and 11.0 speed's.
"To set the 2.4-GHz, 802.11g radio to serve only 802.11g client devices, set any Orthogonal Frequency Division Multiplexing (OFDM) data rate (6, 9, 12, 18, 24, 36, 48, 54) to Basic."(c) Cisco IOS Software Configuration Guide for Cisco Aironet Access Points 12.3(7)JA
This the same thing as entering `speed throughput ofdm`? Command disables all 802.11B data rates as you recommend.
> They may be able to respond / attempt association (that all happens at either one or two mbps for either "b" or "g" ... long or short preambles), but since they dont have compatible data rates, they can never connect.
I know... But, AFAIK, when 802.11G AP "see" 802.11B client in his coverage area AP "downgrades" to 802.11B to allow this client associacion. Your recommedation prevents this, i'm right? Try to understand me, many years i used damn D-Link (my boss love it) but one day i sad "Cisco or on no any kind wireless :E" and now i have dosens AP-1200 with my many questions... All want now i want - is set "G-only" (in dlink's terms) like function...
Thank you
P.S. Sorry for my english

I have problem with Cellular data network it is not apearing in iphone setting so help me how to bring this option in iphone

i have problem with Cellular data network it is not apearing in iphone setting so help me how to bring this option in iphone

What brand/model USB drive? Is it bus or AC powered?
On Mail...
First Quit Mail, then I'd backup these two Mail folders, by right clicking on them in the Finder, then choose Archive/Compress.
Users/YourUserName/Library/Mail
Users/YourUserName/Library/Mail Downloads
(Could be a different folder here if you chose such in Mail Prefs)
Right click on that Mail folder, choose archive, you'll get everything in the folder, and the folder itself in a file called Mail.zip, move it to a safe place, same for the Mail Downloads folder... only the plist is separate.
/Users/YourUserName/Library/Preferences/com.apple.mail.plist

Window 8 WiFi problem with Cisco wireless network

Anyone encounter a Windows 8 WiFi authentication problem with Cisco wireless network?
We are using WLC 5508, 7.2.111, and AP 3602i with WPA2.
Sent from Cisco Technical Support iPad App

This problem occurred with Soney, and Dell models. Lenovo with Windows 8 factory installed is working fine.
Won't make any difference as these laptop's wireless NIC cards are different.
Can you try with OPEN authentication. If the Sony and/or Dell laptop works, then you start cranking up the security and/or encryption settings until you break them.
I'm with Scott here: It's got to be a wireless NIC card driver.
As what George has stated, post the debug of the failed attempts.

Time Capsule (SIM) expand network with 802.11b/g Airport Extreme

Hi, I try to expand a Airport-Network which is set up with a Time Capsule (SIM (latest model). I like to use an Airport-Extreme-Basestation to expand the network. The two devices will be connected wireless. In the helpfile there is a explantation how to do this with 802.11n-devices but when it comes to the 802.11b/g-devices it just says I should have a look on the apple support-pages. I do not find anything there.
I tried everything, but it did not work. I've had a Time Capsule (first model) which died some days ago (the well known powersupply problem). With this Time Capsule I did not had any problems to set up a WDS.
What to do?
Message was edited by: Kadege

Kadege wrote:
Ok Jolly, thank you, but I started this thread to get in contact to somebody who knows the solution, i.e. has done this before.
Jolly Giant wrote:
try automatic
Of course I've already tried this and the other automatics, but it did not work. That is the reason I am asking for help. So I guess I need special settings.
NOT good !
No protection is not good, ok. But I want it to set up and running and after this I can switch on protection to eleminate some mistake-reasons.
WDS-Mode: "remote WDS-Basestation"
when the UFO joins the TC's network this will no longer apply
But this menu exists and the UFO does not join the network, so I have to select any of this settings!
try these steps provided by Tesserax:
Setting Up Time Capsule as a Second Wireless Router
802.11g AirPort Extreme Base Station -> 802.11n Time Capsule
With "mixed" AirPorts, you will need to configure both routers into a Wireless Distribution System (WDS). Your neighbor's AirPort Extreme Base Station (AEBS) will be the main and your Time Capsule (TC) will be the remote base station in this WDS.
To simplify setup, you should connect your TC directly to the AirPort's LAN port by Ethernet. Once the WDS is configured, you can disconnect the TC and place it at the desired location.
The following are the basic configuration steps to create a WDS:
(Note: To facilitate the WDS set up, jot down the AirPort IDs (MAC addresses) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.)
Main Base Station Setup - AEBS
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the main base station, and choose Manual Setup from the Base
Station menu, or double-click the base station to open the configuration in a separate window.
o Enter the base station password if necessary. If the base station is using the
default password of public, you will not be prompted for a password.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the AirPort ID of the base station you want to connect to this base station.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup - TC
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the remote base station, and choose Manual Setup from the Base Station menu.
o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of the main base station in the WDS Main field.
o Click Update to transfer the settings to the base station.
(ref: Pages 42-46 of "Designing AirPort Networks.)
802.11n AirPort Extreme Base Station -> 802.11n Time Capsule
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
does this fix it for you ?
edited by the Jolly Green Giant (where Green stands for environmentally friendly)

Extending home wireless network with 802.11b/g Airport Expresses

Home Setup: iMac with iSight G5 2.1GHz PPC, OS X Leopard 10.5.8, 2.5GB memory, 2 Airport expresses-802.11b/g.
Up to just recently, I was able to use my AE's to create a whole house wireless network: one as my main network connected to my cable modem, and the other as a wireless network extender. My extender got pulled out one day accidentally, and when I went to plug it in it wouldn't reconnect to my network...and so the problems began. Airport Utility used to give the option of "Extending the Wireless Network", but no more.
I've done a lot of searching through the forums regarding this issue, read through the sage advice by superusers Tesserax and Bob Timmons, and attempted to set up my main AE as my "WDS Main" AE and the other as my "WDS Remote". The WDS main connects fine to the internet, but the WDS remote continues to show a flashing amber light and inability to extend my wireless network. I've done soft and hard resets to the remote AE (which transiently gives me a green light, then back to flashing amber), network diagnostics using the Airport utility, but still no luck. The AE wireless extender continues to flash amber and is nonfunctional.
AE Wireless extender settings reported:
-WIreless Mode: Create a wireless network
-Connect using: Ethernet
AE Errors reported:
-Ethernet Unplugged
-Default Settings
I setup the AE Wireless extender as a WDS Remote, it resets and shows "Normal" without problems reported in the summary window of Airport Utility. Connection indicated as "Airport (WDS)" and Wireless Mode reads "participate in a WDS network", but the AE is still flashing amber and will not connect to the internet or Main WDS wireless network.
Went to the Genius Bar at the local mac store...they couldn't help at all.
I'm out of answers...help?!
Allan

There are basically two "flavors" of WDS that the AirPorts support: static & dynamic.
o A static WDS allows for a main, relay, and remote base stations in the configuration. This only operates in the 802.11g radio mode. Its advantage is it is well suited when you are trying to cover a considerable linear range ... like a rectangular house where the Internet connection comes in at one of the shorter sides and you want wireless at the other end. The biggest disadvantage of this type of WDS is that for every base station added, you lose half the overall bandwidth.
o A dynamic WDS allows for only a single main and multiple remotes. Think of a wheel with the main at the center and the remotes as spokes of the wheel. The advantage of this type of WDS is it operates in the 802.11n radio mode and doesn't suffer a significant bandwidth loss like the static version.
As a minimum, a dynamic WDS requires two 802.11n AirPorts (or Time Capsules). You can create a static WDS with either all 802.11g AirPorts or a mix of 802.11n & 802.11g AirPorts. Note; however, you cannot create a dynamic WDS with mixed mode base stations.

Windows 7 Wireless Logon - Problems with 802.1X Machine & User Authentication

Hello All,
We’ve had difficulty with our Windows 7 clients authenticating to our wireless network. I’m hoping someone out there has experienced the same thing and can offer some help.
Some info about our environment:
Single Windows 2008 R2 domain with 6 DCs
MS Radius server
Aruba wireless controllers
The Problem:
The client computer boots,
Auths as machine (802.1X successful)
User enters creds
User auth (802.1X successful)
To this point, everything is working normally. Next is where it gets weird.
During the logon process, there is another machine auth
2-5 minutes later another User auth
OS is up and usable (connected to wireless network); however, no homefolder is mapped and GPP didn’t apply properly.
From what I understand, after the user has logged in, Windows never attempts another machine authentication. When the user logs out, Windows can attempt it.
Can anyone offer some insight to what is causing this? I have logs available if anyone is interested.
Thanks in advance for any help you can offer!
Brett
-- Brett

I did a network trace to gain more insight. I don’t understand why after 802.1X auth is successful on port 1, it then initiates 802.1X auth on port 2.
Can you offer any insight?
10487    3:50:19 PM 8/23/2012    63.0340126
ONEX_MicrosoftWindowsOneX                ONEX_MicrosoftWindowsOneX:Port(1 (0x1)): Authentication Starting   {ONEX_MicrosoftWindowsOneX:126, NetEvent:5}
10867    3:50:19 PM 8/23/2012    63.3403904
ONEX_MicrosoftWindowsOneX                ONEX_MicrosoftWindowsOneX:Port(1 (0x1)): Time taken for this authentication = 281 (0x119) ms
{ONEX_MicrosoftWindowsOneX:126, NetEvent:5}
Then >>>
11718    3:50:35 PM 8/23/2012    79.3196653
ONEX_MicrosoftWindowsOneX                ONEX_MicrosoftWindowsOneX:OneXDestroySupplicantPort     {ONEX_MicrosoftWindowsOneX:126, NetEvent:5}
11938    3:50:36 PM 8/23/2012    80.0530315
ONEX_MicrosoftWindowsOneX                ONEX_MicrosoftWindowsOneX:Finished initializing a new port with id=2 (0x2) and friendly name=Dell Wireless 1504 802.11b/g/n (2.4GHz)
{ONEX_MicrosoftWindowsOneX:126, NetEvent:5}
11959    3:50:36 PM 8/23/2012    80.0556734
ONEX_MicrosoftWindowsOneX                ONEX_MicrosoftWindowsOneX:OneXStartAuthentication           {ONEX_MicrosoftWindowsOneX:126,
NetEvent:5}
11964 3:50:36 PM 8/23/2012
80.0557074 svchost.exe (1036)
ONEX_MicrosoftWindowsOneX ONEX_MicrosoftWindowsOneX:Port(2 (0x2)): Starting a new 802.1X authentication (MSM initiated)
11965 3:50:36 PM 8/23/2012
80.0557333 svchost.exe (1036)
ONEX_MicrosoftWindowsOneX ONEX_MicrosoftWindowsOneX:Port(2 (0x2)): Authentication Starting
-- Brett

Slow wireless speed with new iMac Intel- problem with 802.11g?

There IS a problem with the new Intel Mac, I have tried both the Intel iMac and the new Intel Mac mini and they both have the same problem with slow wireless speed (or rather it variates, if I do a ping to another computer on the network the speed goes from < 1 ms up to 1000 ms and then down to < 1 ms and so on). The older mac minis, my Linux boxes and my Windows PCs don´t have that problem. I have also read reports on the net and it appears that most users experiencing this problem have wireless card firmware version 101.3 (3.120.28.3) . A possible "fix" is to change to 802.11b on the router and then it works. No speed fluctuations and a stabile network! I know it is a bad solution, I would prefer to use 802.11g and get the speed. However I think this points to a problem with the drivers regarding 802.11g. I am starting up a new thread on this and those of you with problems, please try to switch to 802.11b and if it works let us make Apple aware of this.
/Tobbe

Which home hub do you have?
There is some general help at this link Wireless connection problems
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Did anyone manage to connect to a 802.11b network?

My MBP won't connect to my 802.11b router wirelessly.
It gets an IP, but the broadcasts it sends are not responded by the router or any other computer on the network.
The most likely option is, that the MBP broadcast in a "g" only mode, regardless of the fact that it should be "b/g" compatible.
My airport card firmware is 0.1.17
I wonder if anyone else can connect to a "b" router. I know that almost everyone has "g" noadays, but I don't and it bugs me that I'll have to get a new one.
MacBook pro Mac OS X (10.4.6)

Well, off course I tried all the security/no-security options the router supports. Won't work even without security.
I repeat: the Mac connects with IP (real) and all. It says it's connected, it also appears on the list of wireless connection on the router - but the transmissions the Mac sends (and it sends a lot) are not responded.
A friend of mine, a system guy, who tried to check this, said that the Mac's transmissions don't even look like "b" transmission - they are longer (or something of that sort).
The thing is: If I knew a way to enter the wireless card driver configuration, it probably would solve it. and I don't mean through the system preferences - there's nothing serious there.
On a PC it is so easy: you simply tell the card to work in a b/g mode, rather then a g only mode.
MacBook pro Mac OS X (10.4.6)

Homehub 3 problems with wifi and network - please ...

I am hoping someone can help me, as I am struggling to work out why I am getting so many problems with my network at home.
I have BT Infinity, and a Homehub 3A. I have had BT broadband for years. Infinity was added in Feb 2013. The HH3A is the original one supplied to me years ago.
When Infinity was installed I also added a pair of TP Link powerline adapters, to provide a connection to an unmanaged network switch in the lounge.
A rough outline of what I have connected to the router is:
Wired
- Synology NAS Diskstation
- Win7 laptop
- powerline adapter
Wifi
- 3 iphones
- 2 ipads
- Win7 laptop
- 2 Win Vista laptops
Powerline / network switch
- Sonos bridge
- TV
- BluRay
- Vodafone booster
- SkyHD
Recently I am getting a number of different problems:
1) wifi drops to everything connected to the router, at the same time, all blue lights are on the router
I lose wifi connection to the internet, from all devices, at the same time, but also the connection from my laptop to the NAS drops.
2) Anything connected to the Powerline adapter is rarely available
I try and connect to Sonos, or my sky box or the TV, but they aren't connected to the router. The lights on the powerline adapters indicate everything is fine, and the HH3 has all blue lights. But my iphone and laptop cannot find my Sonos. My iphone app cannot find my sky box. And on the TV it says it is not connected to the internet. To solve this problem I have to power cycle the pair of Powerline adapters.
Some observations:
1) these problems are all since Infinity was installed. I have no idea if that is relevant.
2) My NAS Diskstation has a powersave mode. I noticed last night that when I woke it up, the powerline adapters disconnected briefly, before reconnecting. But when they did reconnect I could not access anything connected to them. It was as if the NAS had booted them off the network, and then they couldn't get back on.
3) I run a 10m brand new Cat5e cable from the infinity modem to my router, because the modem is in the garage.
Can anyone help? I am tearing my hair out with this.
Thanks for any help.

If you set the devices on the home hub to always use the same IP address, then that can help.
The problem is that when the DHCP lease expires, the home hub often gives the device a different IP address, and this breaks the port forwarding rules.
Some routers allow you to specify which IP addresses are to be reserved, but the home hub does not.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Problem with Airport wireless network utilising a Time Capsule. No internet connection?

Right, I have an Apple Mac and I am creating a Wireless network with an Apple Time Machine. I have had both devices for approx 2 years, they have be fine to date - until I now have the following issue: The Wirless network has been created and can be connected to but that network isn't then connected to the internet. IN have checked with the Cable network provider Virgin and there is a network without proplem provided to the Modem - I have also connected an ethernet cable to direct to the Mac and connected to the www, no probs. I have also asttempted to reset and set up my time capsule / airport again howver the same problem arises. When I go to network Diagnostics I Have a green light for the following; Airport, Airport Settigns, Network Settings,Network Settings, ISP then an amberlight for Internet and server.....Please assist!!!! Is this an ISP address issue. Welcome any help, Thanks in advance. Jimbob

Sounds like chaos..
How many outlets are we talking about and what specific equipment?
Do you really need routers on every one? How many clients do you use?
Basically there are three non-overlapping channels on 2.4ghz.. using more than three routers in the house is pointless as they will just interfere with each other.. range on 2.4ghz should be sufficient to reach at least half a normal house from one AP. If not there are better high power routers available.
And there should be just one device that is the main router.. all the other routers should be bridged/ wan bypassed so they are merely AP and switch. Otherwise NAT will cause issues to devices stuck behind a secondary router.

Experiencing three problems with Thinkpad T530 (Network, keyboard, and touch pad)

I bought thinkpad t530 2 years ago and gave it to my sister 4 monts age and recently she is experiencing few problems.
Before I mention any problems with it, I would like to mention that my sister hasn't updated software or driver for more than 60 days through lenovo solution center.
First, she cannot connect to a network (both wirelessly and internet cable).
The error says "There might be a problem with the driver for the Wireless Network Connection 2 adapter"
Second, the keyboard is not working.
The keyboard works fine when it was in BIOS mode and the keys associated with Fn keys work fine too, such as brightness contorl and backlit keyboard keys. However, it seems like the keyboard doesn't work in Windows 7. When she went into drivers manger to see what was the problem, it says, "Windows cannot load the device driver for this hardware. The driver may be computed or missing. (Code 39)"
Third, the touchpad and red pointer is not working.
Similar with the keyboard problem, the touchpad and red poting device is not working. In the device manger it says,"This device cannot start. (Code 10)."

Hi Rbtlr0215,
Welcome to Lenovo Community!
As per the query we understood that you are facing multiple issues on your ThinkPad T530.
For keyboard issue, check if the issue persisting in ‘Safe mode’ option. Check with uninstalling the Keyboard adapter from device manager.
For internet issue, check if the issue persists in ‘Safe mode with network’ option, Check with uninstalling the Wifi drivers from Control panel – Program & feature options.
For Touchpad issue, check with uninstalling the UltraNav drivers from Control panel – Program & feature options and restart the system, let the Windows install the generic driver for your system.
After performing all the above steps run thinkvantage system update utility to check for latest driver for your system.
Hope this helps.
Best regards,
Hemanth Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Problems with 802.11b networks

Similar Messages

Maybe you are looking for