Problems with audio track through US-122 in Logic Express

Hi,
This may be a completely stupid question, but I'm having problems with recording through my Tascam US-122 in Logic Express. I can't get anything to register on the level meter in Logic Express (neither direct input nor microphone input). However, I can get the input from the Tascam to register in the system preferences menu outside of Logic, and can get the built in mic on my IBook to register inside of logic. Does anyone have any ideas for me to try out? I've looked in the manual and I'm supposed to be getting the Logic Express training book soon, but I was hoping to record sooner than that.
Thanks!
Shawn J

Sorry, ignore the above. I needed to enable record before the level would show up.

Similar Messages

Problems with audio tracks

Happily pressing on with my first project when problems arose with audio tracks. Suddenly - when I added video clips I got sound on A2 but nothing showing on A1 (and sound only from right hand speaker). Clips are okay as sound is on both sides when played in Viewer and Canvas just can't add them both to timeline. It was okay up until the point I did my first audio fades within a clip (using the 'elastic bands'). Now I can't even insert a clip with both tracks ahead of that point. A1 just won't accept anything.
Now when I add a clip I only get audio on A3!!!!
Voiceovers all went onto A6 and are okay but is it normal for them to hide down there?
I am sure this is finger trouble on my part as I am so new to FCE but can anyone tell me how to recover?
Thanks,
Tom.

Sounds to me like the audio targeting is amiss somewhere.
In the audio tracks you will notice a1 & A1: meaning audio track 1 and the audio will go to that track when edited. To get stereo, two tracks will be used eg. a2 & A2. Having A1 and A2 is FCEs default setting with a1 & a2 selected. This setting will place stereo audio into these default tracks. If, for example, you want the tracks to be edited to A5 & A6 then you move the a1 to a5 and a2 to A6 (click and drag). This is called track targeting for obvious reasons, untill you change it, all new edited tracks go to tracks 5 & 6.
Click on a1 twice, did you notice it move and seperate from A1, this is a de-selected state (a gap between a1 & A1). When a clip is edited to A1 in this state it means no audio will be added to that track. Most likely you have an unlinked audio track. I hope this brief bit of info helps you figure out what audio ends up where in the Timeline.
Regarding recovery, you could try the AutoSave Vault. Go back to a date and time that is before things went wrong and open that project.
Al

Problems with audio track when burnt to DVD

Hi there,
I'm using CS4, and have created a 30 minute film which I've exported as an H.264 - it's 653MB. When I play this file from my PC, it's perfect. When I burn it to a data DVD, however, the audio track is interrupted every few seconds with blips of silence - like it's stalling. (I've been unable to burn it as a video DVD so far as the various software I've tried rejects the file format.)
I've burnt it twice on my laptop and once on another desktop with the same results. I urgently need to send the file to a Mac owner - what should I do? Could this be a fault with the file or with the burning software? Perhaps I didn't do something right with the audio track?
I'll greatly appreciate your help!
Thank you :-)

For authoring a DVD-Video, follow Harm's advice and Export to DV-AVI Type II w/ 48KHz 16-bit PCM/WAV Audio.
For a DVD-Data, you should not have an issue with the H.264, BUT some have had problems if using Apple's H.264. Many users find that the Lead, or MainConcept H.264 has fewer issues.
Also, do you have a Matrox card? They have been known to cause Audio issues, so you will definitely want to update any Matrox drivers.
Good luck,
Hunt

Problems with audio panning.

Am having problems with audio tracks. For example: when capturing a clip where a person is talking, there would be 2 tracks of audio - one a radio mic (Track 1) and another mic (Tack 2)capturing ambient sound. I often delete the ambient track (Track 2) and am left with the the main audio from a radio mic (Track 1).
The problem is when I open up the main audio track (Track 1) and pan the audio track from -1 to 0 or even to +1! It says it has done it but the sound still comes out of the left speaker.
It is a very recent problem that I wonder may be something to do with preferences or settings.
We have had no problems with the speakers at all.
Thanks very much,
Geoff

You have your audio outputs set to 'dual mono', not 'stereo'.... go to:
Sequence>Settings> 'Audio Outputs' tab > then highlight the 'Stereo' button, then click OK...
problem solved...

Slideshows with Audio tracks

I am trying to add audio with my slide-show by adding a track from a cd.
Unfortunately however, I get the message:
"There is currently not enough audio in slide-show to fit the slides.
A minimum of 39 seconds is required."
The piece of music selected is 2.27MB.
I am successful however when using music from the My Music samples
file provided with my computer - 747KB.
I am run Windows XP
Your help will be appreciated.
Ron Knuckey

Slideshows with Audio tracks
Good evening Barb and thank you for your quick response.
I am delighted to tell you that I followed your advice and instructions and am now able to add Audio to my slide-shows.
It had become a frustrating problem until I received your help this a.m.
I am ever so grateful to you and next time I have a similar problem I shall call you first!
You have saved me a lot of wasted time and for that I thank you.
I have marked you in my Help folder as A1 and it is good to know that you are there if I need you!
Many thanks again.
Ron Knuckey

Problem with Audio on HP Envy 6-1130sw (C6F62EA)

Hello everyone.
I have a problem with audio on my ultrabook HP Envy 6. Sometimes when I try to play music there are no low tones and music plays really silent... And then when I restart PC problem dissapears and music plays fine... I thought there is a problem with speakers, but when I connected 5.1 speakers there were also only high tones. Same thing happens on headphones. Is it a hardware problem or maybe software? Actually I use Windows 8.1 and drivers are up to date. If any one of you had same problem please post.
Thanks.

Hi piotrek1130sw,
From what you have described, I think the best approach would be to restore the original IDT driver, restart the computer, test that driver, then install the driver update, and test the outcome of installing the newest driver.
Use the following link for instructions to recovery the ITD driver using Recovery Manager. Restoring applications and drivers.
Once the driver is restored, restart the computer and test the audio. If the audio is good you can continue to use this driver, or you can reinstall the update and see what happens. IDT High-Definition (HD) Audio Driver.
If installing the newest driver causes the issue to occur but the recovered driver worked, I suggest recovering again.
If neither driver works I will gladly follow up and provide any assistance I can.
Please let me know the outcome.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Problem with audio configuration

when i turned on Itunes on on my computer it had this message: Problem with audio configuration. Audio/video playback may not operate properly. How do I fix it?

I reinstalled iTunes & QuickTime as per giterdone response to rpestow on 12 November
instructions at: http://docs.info.apple.com/article.html?artnum=93698
Thanks giterdone

Problem with Audio MIDI Setup using multiple accounts

I'm having a problem with Audio MIDI Setup recognizing all of the MIDI devices on a G4 Tower with a non-administrator account. The main administrator account has no problem seeing anything, but the non-admin account won't see anything. Does it all have to be added in manually, or is there a preferences file to copy over that will take care of this. Failing that, is it a problem with file permissions? Any help would be greatly appreciated.

Don't know whether this of any help, but there's an identifiable issue with AMS and Digital Performer 5 where DP5 simply won't load with AMS setups configured with previous versions of DP. Which is probably irrelevant to your problem, but ...
What I and other DP users have found we have to do is start with a completely new, blank AMS setup, and reconfigure our devices from scratch, and although this was kind of hit and miss and on the fly (don't really understand what the the issue was, exactly), I think the bottom line was if we used the new AMS setup with DP5 before anything else that might cause its data tables to change, we were ok.
So if you can do it, it might be worth setting AMS to a new blank template, then connecting your interfaces, see how far you get. And always make sure you've got the latest drivers of course, though I'm sure you've done that.
Never used Mbox or 410, but I've an Ozonic which I think uses the same M-Audio firewire drivers as the 410, and don't have any problem with that, FWIW.
G5 Dual 2.7, MacMini, iMac 700; P4/XP Desk & Lap. Mac OS X (10.4.8) mLan:01x/i88x; DP 5.1, Cubase SX3, NI Komplete, Melodyne.

Two problems with audio clips

Hello,
I'm having two problems with audio clips:
1. When I try to drag a clip from the viewer, I can't do it because it won't let me drag the clip. It only lets me drag the pointer around within the clip.
2. When I drag an audio clip from the browser into the timeline I don't get any audio, just a series of beeps (and yes, my audio media is on-line -- I can listen to it in the viewer, just not the timeline).
What am I doing wrong?
Thanks.

1. Drag the little hand on speaker icon to drag from
the Viewer...
Thanks! (Does it actually say that in the documentation anywhere? I try to RTFM, but the FM seems to be a little, er, mute on this point.)
2. It means your sequence settings don't match the
properties of the source audio you're putting in it,
and you either need to change the settings in the
sequence, or render the audio.
Ah, that would explain it. Thanks!

Premiere pro cc 2014 problems with audio

I have edited some sequences in premiere using sony xdcam ex clips. The clips where recorded as 1080 50i. I have edited it in the same sequence properties as premiere sugested it. All there is fine and audio is playing well. The problem strats when i change the sequence properties and select it at 1080 60i or 29p. The audio is distorted and it sounds like robotic, sometimes audio is muted on audio transitions. When i revert the properties back to 50i then all is fine.
Anyone else experience the same problems?

Sometimes i must add some clips that are recorded on canon 6d on 29.97p. and this clips look choppy and jerky on 50i sequence. But on 60i sequence both 50i and 29.97p look good. On premiere cc i cann change sequence properties without any problems with audio, only on cc 2014 that audio problem exist.

[Vox] MSI VOX TV BOX USB 2.0 problem with audio drivers compatibility

Ok,let's go...
I have a DELL Latitude d510 laptop with a centrino 1.73 GHz procesor and a soundcard supported by Sigmatel software Sigmatel C-Major audio.I bought MSI VOX TV BOX USB 2.0 and tried to install it on my lap top.Yes,I had problems with SP2 on my XP and the MSIVPS software from the instalation CD was crashing every time I tried to start it,but I solved those problems by downloading the latest drivers and the 3.xx version of MSIPVS.But...I still have a problem with audio.To be precise it seems that my audio drivers are incompatible with the VOX drivers.So now I have video but I don't have audio.Also I installed the tv card on my desktop machine and it worked like a charm(everything workes:audio,video,the old MSIPVS which I like better than the new one cause it supports my remote,has better way of managing scanned channels,e.t.c ,but I have USB 1.1 on my MB so the image quality is very poor).I did a lot of experimenting,for example i uninstaled my audio drivers(that Sigmatel C-Major thing),and installed the old MSIVPS and guess what...IT WORKED but there is no use from this cause I don't have audio On the other hand if I have everything installed then in the MSIVPS (the 3.xx version not the old one) under audio I get CD Player as an input audio device(what happened with microphone...?).To cut the long story short I tried a bunch of things and still no audio.Is there any other case of DELL audio software-VOX incompatibility?Any ideas,or solutions?

thank you for answering me. y have no pci card working, only usb 2.0 and sata devices. also, the MSI geforce 9600gt PExp 2.0 gpu. the only usb 2.0 devices which work, are the flash (pen) drives, keyboard and mouse. but no way that the WLAn adapter and TVcapture, both usb 2.0 work.i've tested them front side and rear side and is the same failure: if i use a pendrive, works ok. if i insert the wlan or the tv capture stop work as the 2.0 and a advertising window tell me to change to a 2.0 port, means the ports are working slower, at 1.1. i still have the other PC, built on the MSI K9N4-slif mobo, tested them and both devices work at perfection. i have 2 screenshots to show you:
this, is the device manager (sorry, in spanish but you understand that's about the nVIDIA EHCI USB 2.0 controller. the 2nd one seems to be more sensitive (works worth) then the first one. when the tvcapture begin work, then fails, i'm trying to update this controller, does it ok but then the devicemanager-window freeze. i must stroke the "enter" key to "accept" / finish the update. then, fails again:
the other one is from everest corporate edition:
both drivers marked with purple colour!
i think i should update this Win XP drivers, but how? the usbport.inf file (C:\Windows\inf) don't change anything. i don't want to switch xp to vista, i'm happy whit it.
i'm thinking also on another possibility: could be an energy failure? some usb devices, like the big usb flash dives. 250-320gb, fail because the 5v/usb are receiving it's not enough. could be, but that means this mobo has no solution and i'll loose my money.
thank you very much and i'll stay alert of your suggestions. by

Can't run itunes because it has detected a problem with audio configuration

What does that mean and how do i fix it? I had Itunes installed on my computer for ages but I had to have it restored because the firewall was playing up and since i have tried to reinstall itunes it has been saying that there is a problem with audio configuration---any ideas?

Some people have found the following works:
Completely uninstall Quicktime (NOT iTunes) using ALL the method in this article:
http://docs.info.apple.com/article.html?artnum=93698
Turn off antivirus/anti spyware
Go to Control Panel>Add/Remove Programs>Change or Remove Programs
Select iTunes, then click on Change, then select Repair.
Restart computer

Problems with installing Xcode through App Store

Hey guys,
So trying to install Xcode on my Late 12 Macbook Pro with the ML update for a project with work.
Everytime I try to install through the app store, I get the Grey Screen of Death. Anyone else having this problem or what could it be? I've had no other problems with installing programs through the App Store.
I am currently downloading through the developer portal, so hopefully that works.
Hope someone can guide some light on this.
Thanks guys!

Hello,
For you problem with the Mac App Store you can contact the support here :
http://www.apple.com/support/mac/app-store/
(choose Account and Billing; you can change the country at the bottom of the page if you prefer dutch and go back to the support page).
For your problem with Mail and iCloud you can read this page :
http://support.apple.com/kb/TS4002?viewlocale=nl_NL (Troubleshooting iCloud Mail).
Hope this will help.

Problems with Audio in iPhone 5

I Have a iPhone 5 and today beginning having problems with audio, I can't hear my calls or music, somebody have the same problem?...do you know how I can fix it?

Do you have the side switch enabled - do you see orange on the switch above the volume keys.
Make sure all your settings are turned up.
Try a restart of the phone by holding the home and power button until it reboots
If that does not work you can reset your settings by going to settings > general > reset > reset network settings and then reset all settings.

Problems with audio programs after update to Maverics

After updating to Mavericks on my Mac Mini there is problem with audio programs. I cant open iTunes at all, I click it and it disappear in a second. Also when I press play in GuitarPro 6 or in Vox player nothing happens. It just wont start playing. I really dont like this update.. and my mac is slower now. I cant downgrade my system back so this is really frustrating to me as a musician.

I have the same problem with my Conceptronic CH3HNAS and have found a free and easy solution.
Since a lot of people report they are able to access their NAS using apps other than the Finder itself, I decided to look for a free Lion-compatible File Manager to use instead of Finder.
I have found muCommander ( http://www.mucommander.com/ ) and indeed it works fine. All I did was click on the button highlighted bellow, go to "bonjour services" and select my NAS. It prompted me for my username and password and voilá, it works fine.
I keep Finder for everyday use and just load muCommander when I want to access the NAS. At least now I don't have to start my WinXP VM anymore just to access it.
Hope it helps you.

Problems with audio track through US-122 in Logic Express

Similar Messages

Maybe you are looking for