Problems with C7 symbian Anna updating

Please answer immediatly!!
I have a C7 with Symbian Anna
Today I update the software with Ovi Suite but on 3th phase, the Cell doesn't restart
Pleaseeee help me!!
How can I resolve the problem?

If I remember, the difference is that via NSU the firmware gets updated as a whole, but via OTA it's updated over the top of existing firmware or it's added to what already exists in the phone. Similar to the difference between upgrading from say from an older version of Microsoft windows to a newer version vs a fresh install of a new version

Similar Messages

Symbian Anna update 1/2 failed to install

The story so far. I did the first round Anna update (around 27 mb i think) OTA cos my Ovi Suite never able to update firmware on my n8 since trying to update it to PR 1.2, and I did try reinstalling, redownload, reboot PC, reg clean, ccleaner to fix the Suite but it still do not update my firmware at all. But that's another story.
So I installed the 1st round, n8 rebooted to white screen, rebooted into homesceen with Midnight theme. SW update then shows 4 more items: Anna update 1/2, 2/2, Store and Social. The 1/2 was showing around 20++ mb. So I selected all 4 and update. Halfway through the installing process of 1/2 update (note the download part of 1/2 was very fast), I did plug in the power pin, cos the installation process was damn slow for 1/2. I did not notice wheher it finised installing cos later i checked it was already on 2/2 (downloaded and installing). It then went to the last two items and installed ok.
Rebooted device, but SW update still showed Anna update 1/2 available (the only one left) and the download size is now 7166 kb. I proceed to update it, it failes with error but no error codes or any message what was the error about. I tried again and again, with fresh reboots, still failes. What gives?
Even more, split screen not here. I did the uninstalling Swype, activating qwerty mode in portrait, still no split screen. I do not have any Betalabs apps.
My Quickoffice & Reader is not here anymore (the app manager not showing them too). Heck I bought the full ver of Quickoffice 6 last time. Wat a waste of my money now that ver 7 is out!!
Anyone knows how to delete the "dowloaded cache" of SW updates? I want to force SW update to redownload this 1/2 item to try fix this issue.
Thanks for listening and please help. Cheers!!
Solved!
Go to Solution.

I got the same problem since this morning on both my N8 & just found out solution on a previous update error similar to this & completed the update on one of the N8. Re-trying on another one.
Working Solution for failed update was found on Flashism's website quoted & "touched up" per below:
Big thanks to user “Unick” on Nokia Support Forums, who posted a working solution to the problem, and there are couple of successful installs reported from the solution.
I just deleted folder E:\Private\20019119\. After that I ran SW update on the phone & it restarted download of Symbian Anna Update 1/2 & 2/2 as well as Social, they finished updates successfully.
To delete the mentioned folder, follow these simple steps:
• Connect your Nokia N8/C7 in Mass Storage mode to PC via USB cable
• Locate and delete folder named “20019119″ under \Private folder of Mass Storage
• Unplug the device from PC, and retry again. It should work.
However, I still got no popup split keyboard after completing the updates & restarted the phone.

Looking for a site that shows problems with windows patches or updates.

Looking for a site that shows problems with windows patches or updates...so I know what not to install.
Plenty of sites list and summarize individual patches, I want one that consolidates problems and complaints so I can better assess the risk. Currently I'm waiting to install patches several days and doing google searches. That works, but I'd rather find a place
that does it with expertise.
Which forums would be best to look for such problems.
Thanks in and advance for suggestions

Hi,
I agreed with Cyber and Rick.
Windows update helps to keep your PC safer—and your software current—by fetching the latest security and feature updates from Microsoft via the Internet.
Although there might be some problems when installing it, Windows update is not the one to blame.
For troubleshooting Windows updates, if needed:
Fix Microsoft Windows Update Issues
http://support2.microsoft.com/gp/windows-update-issues
Best regards
Michael Shao
TechNet Community Support

A problem with Nokia 5530 wirmware updating! Help!

Hi all,
I have meat the problem with Nokia 5530 firmware updating: updating allways finish with the message "Downloading of the variant package failed.Most probably there is non-commercial software in your device."
Is there any solution for that problem?
Thanks and regards,
Alexander

first its ok
then
translation:
For a better connection please insert the usb-cable directly in to the computer and not trough a usb-hub or -keybord or a dockingstation of a laptop.
Nokia Software Updater has tried downloading the software, but this is failed 4 times.
Its posible that it can be caused by a bad, slow or instable internet connection.
This failure can also occur because we have maybe a problem with our servers.
try later again
i tried it on 2 PCs one with vista and one with XP plz help me
Message Edited by progunnl on 13-Mar-2009 02:50 PM

Good evening I would please help me, IGood evening I would please help me, I have problems with flash player when update on my computer Flash Player for windows 8, gives me error in the installation that is not apply on my computer. Please help. Thank You

Good evening I would please help me, IGood evening I would please help me, I have problems with flash player when update on my computer Flash Player for windows 8, gives me error in the installation that is not apply on my computer. Please help. Thank You

First, confirm that ActiveX Filtering is configured to allow Flash content:
https://forums.adobe.com/thread/867968
Internet Explorer 11 introduces a number of changes both to how the browser identifies itself to remote web servers, and to how it processes JavaScript intended to target behaviors specific to Internet Explorer. Unfortunately, this means that content on some sites will be broken until the content provider changes their site to conform to the new development approach required by modern versions of IE.
You can try to work around these issues by using Compatibility View:
http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11
If that is too inconvenient, using Google Chrome may be a preferable alternative.

Has ayone experienced any problems withe latest apple tv update

who has experienced problems withe latest apple tv update???

Welcome to the Apple community.
There are always a few that experience some problem or other after an update. Exactly what problems are you having please.

Hello, I have a problem with iPhone 5c softhware update ( The iPhone "iPhone" could not be restored. An unknown error occurred (27))

Hello, I have a problem with iPhone 5c softhware update ( The iPhone "iPhone" could not be restored. An unknown error occurred (27))

Error 1 or -1
This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.
The" may need service' meand there is a hardware problem. In that case make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Has anyone else had a problem with data? after updating my phone to the new update, i have all this data, and keep getting notifications that my data is getting high. i never had this problem before.

has anyone else had a problem with data? after updating my phone to the new update, i have all this data, and keep getting notifications that my data is getting high. i never had this problem before.

fair enough. No need for any unnecessary posts either. You issue had been addressed ad nauseum already in this forum had you bothered to search this forum (as forum etiquette would dictate) before posting.
In any case, I hope that your problem was solved.

Problem with CC desktop app update

Anybody has Problem with CC desktop app update?

Hi boloco
here are some soultions, which helped me out on my first trouble:
CC desktop lists applications as "Up to Date" when not installed
Good luck (I have new problems today which could not be solved by one of those)

HT5047 Having problem with the iOS7 verifying update what should I do?

Having problem with the iOS7 verifying update what should I do?

Several other users have reported this same problem. Unplug the charger and then replug. It should resume to 100%.
 Cheers, Tom

Having problem with my camera after updating 8.1.3

having problem with my camera after updating 8.1.3.. how will you fix this

Try Resetting your phone: hold down the home and sleep buttons, wait for the Apple logo, let go of the buttons. If this does not work Restore your iPhone in iTunes.

I have a Iphone 4S and i update a new version 6.1, and i have a problem with wifi from i update this version. What is this problem? thanks Andres

I have a Iphone 4S and i update a new version 6.1, and i have a problem with wifi from i update this version. What is this problem? thanks Andres

Move or Copy the ENTIRE iTunes folder from the old computer or the backup of the old computer to the new computer.

Problem with latest OS X update. 10.10.2. Grey screen. .??

Problem with 10.10.2 update. Getting grey screen. Have tried safe boot but got same result.

Mac OS X- Gray screen appears during startup
Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
b. Boot drive's directory has been corrupted - Repair with Disk Utility.
c. Critical system files are damaged or deleted - Reinstall OS X.
d. The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Symbian Anna update 1/2 not available

Hi,
I have just updated my phone (N8 Hungarian T-Mobile version) to Symbian Anna but the update package 1/2 is not available. Could anyone help? Thanks.
Some details
First I tried to update many times using Ovi Suite but it failed during the backup phase (service not available message) - finally I updated using Nokia Software Updater and the update to Anna was completed successfully.
I went to check the additional update packages but only Update package 2/2, Ovi Store update and Social update were available. All installed successfully. Update package 1/2 was missing from the list of available updates!
As expected, without update package 1/2 the PDF Reader and QuickOffice are not available.
I checked many times yet again but 1/2 still not available. Is there a way I can install update package 1/2?
Solved!
Go to Solution.

Symbian Anna update package 1/2 appeared today as an available update and installed successfully. This issue is solved. Thanks.

Problem with AUTO PUBLISH nd update NEW POLICY to Client .

To : who may concern , which really need urgent help .
after few days of setting up the ZESM , but then i was unable to find is there any setting which can "AUTO PUBLISH " into the Client side . Without the Client need to use the manual "UPDATE POLICY " button ?
Because , we find it that to make it silent update without the CLIENT side need to manually click the UPDATE POLICY , so i would wonder is there any way to have the AUTO UPDATE the policy from SERVER side ?
thank alot first .
From : NX ( which this few days has been keep on try and explore the ZESM 3.5 , 4.0 , 4.1IR )
Which really need help in here , due to we are almost to the end of the setup server and the IT infrastructure .

I would recommend that you READ and UNDERSTAND the Installation and Administration guides from the Documentation (somebody took the job to write those, so be kind enough to read it)
Main Doc
http://www.novell.com/documentation/zesm41/
Your question is answered here:
http://www.novell.com/documentation/...a/bnk7bdx.html
See "Update Interval".
Lastly, this is a public support forum, served on a best-effort basis from the community. As such, there's no guarantee that you'll get an answer, and if you get one, that works and is correct. So, if you have un urgent or important issue, go ahead an open a support ticket with Novell Technical Services in order to be served by professional support engineers backed up by the engineers who wrote the code.
http://support.novell.com/contact/
>>>
From: nxgame<[email protected]>
To:novell.support.zenworks.endpoint-security-management
Date: 12/11/2010 3:06 pm
Subject: problem with AUTO PUBLISH nd update NEW POLICY to Client .
To : who may concern , which really need urgent help .
after few days of setting up the ZESM , but then i was unable to find
is there any setting which can "AUTO PUBLISH " into the Client side .
Without the Client need to use the manual "UPDATE POLICY " button ?
Because , we find it that to make it silent update without the CLIENT
side need to manually click the UPDATE POLICY , so i would wonder is
there any way to have the AUTO UPDATE the policy from SERVER side ?
thank alot first .
From : NX ( which this few days has been keep on try and explore the
ZESM 3.5 , 4.0 , 4.1IR )
Which really need help in here , due to we are almost to the
end of the setup server and the IT infrastructure .
nxgame
nxgame's Profile: http://forums.novell.com/member.php?userid=99703
View this thread: http://forums.novell.com/showthread.php?t=427947

Problems with C7 symbian Anna updating

Similar Messages

Maybe you are looking for