Problems with D-Link DIR-300

I have tried resetting this, powering it off and on, updating the firmware and it still does not work right.
At the moment, I can get internet through the ethernet cable via this wireless router. I also get a wireless signal from the router but it is not connected to the internet somehow. The airport indicator in the top right shows that I am connected. But when I open "network pref's" it shows that airport is "On" and "not connected".
I use PPPoE cable internet so this router is obviously logging in with the password to the ISP because i am online with the ethernet cable via this router. But obviously the wireless part is not connected to the ISP.
At this point I am thinking that this brand new router is broken. Any other thoughts? Thanks!

Ok, I got it working. I had to go into "Network Pref's" and click "Advanced". Then go to the "TCP/IP" tab and click "Renew DHCP Lease".

Similar Messages

Airport Express with D Link DIR-300 in client mode failure.

I just want my Airport Express to join my current network from a D-Link DIR-300 wireless router in order to use airplay. I use the Airport Utility and appear to successfully set up the device. When it is waiting for the airport to restart, it times out and is unable to locate the AE unless I reset the device and start over. The AE flashes turns green, then begins to flash yellow.
What can I do to make this work. I just want to send music the AE, and be on my existing wifi.

Chances are, the Wireless Security settings on your D-Link router and the settings that you are choosing on the AirPort Express do not match up correctly. The result is that the AirPort Express cannot successfully "join" the D-Link wireless network.
To verify if this may be the issue, temporarily turn off the wireless security on the D-Link router and check to see if the AirPort Express can connect that way. If it can, then you know that you have a security setting issue between your router and the AirPort Express.
What are the available security settings on the D-Link router that you are using? We'll try to provide you with a corresponding match for the AirPort Express if you can post back that info.
Message was edited by: Bob Timmons

Computer tend to freeze when accessing internet with D-Link dir-655 router

I recently bought a D-Link dir-655 router and since then my computer tend to freeze up completely when accessing internet. This also happens when certain programs access internet. Otherwise I am usually using Internet Explorer or Opera.
I've found that there are many who experience problems with D-Link router, that they may have problems with certain network card. Anyone who can say if this is a known issues and if it there is a solution or if it is better to buy another router?
Model #: HPE-140sc
Product #: WC779AA-UUW
Software-version#: A1PNv6PrA2
PCBRAND: Pavilion

Hi, Ernst:
Would you consider backing up your files and doing a system recovery?
Maybe the OS has some corrupt registry files or something.
If you recover and then it still does that, your only choice looking at the motherboard is a PCIe gigabit ethernet adapter which would be relatively easy to install, or you could even get a USB ethernet adapter and not even have to open the case.
See if there is a setting to disable the onboard NIC if you have to add a network card.
I would rule out all software problems before buying hardware.
If you want to try some other malware program, I recommend the free Kapersky rescue disk. You burn the file to a CD and boot from it. It scans the drive and deletes any malware or virus files it finds without the PC being in windows. A lot of times viruses and malware can't be removed when windows is running.
Link to the download and instuctions for use is below. I like to use the graphic interface rather than the text interface.
http://support.kaspersky.com/faq/?qid=208282173
Paul

Problems with Dinamic Link between Premiere pro CC and After Effects CC

I'm having serious problems with dinamic link between premiere pro and after effects, really serious problems that have 2 big projects in trouble (a documentary and a video clip) and I had to redo all the work pipeline to the consumer.
The documentary for a spanish TV was made on CC 2014 and a video clip was made on CC. Both of them with a lot of after effects composition in the premiere pro timeline. Render freeze, a lot of playback issues, and many more problems... Until I decided to remove these links between premiere and after effects and render out all the after effects compositions one by one and insert as clips in premiere pro. 1 week working away with back and fourth.
I've got a huge workstation:
i7 4990
32Gb ram
GTX780 3gb
256 gb system ssd
2 Tb project storage
*All my hardware and software are update.
I know that a lot of folks are on the same huge problem and I want to ask everyone:
How do you save this?
What is your pipeline?
Are there any solution?
Best practice to use dinamic link in a huge project?
Thanks,
Ruben Gimenez.
R&D iceblink.es
www.rambot.es

Thank You, Jim -
Unfortunately that specifically did not work.
Based on another comment sent to me, here is what did.
In PProCC
File > Adobe Dynamic Link > New After Effects Composition
In AECC
From that composition created from PPro, I imported the project (aep) initially created in AECC from another team member. Saved the file.
Back in PProCC
File > Adobe Dynamic Link > Import After Effects Composition
Magic.

Hi guys. i have some problem with a link from a pdf on-line,when i click on it,the page adds a "%" at the and of the link and says "page not found" because of it

Hi guys. i have some problem with a link from a pdf on-line,when i click on it,the page adds a "%" at the and of the link and says "page not found" because of it.
This happens only when a load my pdf file on my server, because if i click on the link when the file is on my iPad, the page opens without problem.
Any help please?
thanx

the % sign is often used when there's a space in a name. HTML doesn't like spaces so it fills them with % or %20
try, on the end of that link, see if there's a space built into the page or the link when the page was made
On the web address you may be able to 'backspace' at the end and erase that space to get the address, but whomever made the page possibly put a mistake in the link

Problem with Help Link in search result screen of PCUI

Hi,
I am trying to access the pcui applications that came out of box with crm using BAB,everthing is working fine but got a problem with "Help" link in top right (beside personalize link) the search result area of all the PCUI screens.
when i click on that i get "page cannot be displayed" error, seems that it is pointing to some wrong URL, where should i change the url to point to our company's help site for that link..
clicking on the properties of that link shows that it is pointing to
javascript:CATshowF1(%20'/sap/bc/bsp/sap/crm_bsp_f1_help/f1help.do?doctype=kw&loio=70B4ED8E03595645A6ABA33B4576BB57&class=IWB_EXTHLP&language=E' );
Please help me in this regard.
Thank you

My response help resolve Kodru's Message which he also posted in EP Implementation Forum. He resolved it by changing the variant noted below.
The link http://help.sap.com/saphelp_crm40/helpdata/EN/70/B4ED8E03595645A6ABA33B4576BB57/content.htm should display Activity Info.
First I would check if the crm_bsp_f1_help service has been activated in SICF.
Secondly I would check the settings in the IMG -> SAP WAS -> Know. Mgt. -> Settings in App. Sys. -> Usage of Help Type "Dynamic Help". The Tab PlainHtmlHttp should have a variant called CRM_HELP, Server Name (help.sap.com) and path.

After Effects won't close/Problems with dynamic links

When I quit After Effects the icon still shows up and it says that it is still open, even force quit will not work. Also having problems with dynamically linked files between after effects and Premiere pro. Rendering in Premiere doesn't work unless I go to AE, save the project, then go back to Premiere. I have OSX Mavericks 10.9.2, a late 2012 mac pro, and AE CC 12.2.1.5

Kevin: would appreciate further thoughts on this.
I am using Pr2014, version 8.0.0 I am using AE2014, version 13.0.2.3. When I was on earlier versions of each, I had no problem importing AE comps into Pr. I'd choose import in Pr, then select the AE project, then select the comp. But with my new and improved versions of AE and Pr, I keep getting "importer reported a generic error."
I also tried to go the other way. I selected in Pr the clips I wanted to work on in AE, and then tried "replace with AE comp" but got the "generic error" message again..
Finally, I attempted to create a Dynamic Link from Pr via the File menu, but with each of the options from there, I got "failed to connect to AE Dynamic Link"
Any advice you can share, would be most welcome.

Strange problem with Database LInk

Hi Everyone,
I have strange problem with Database Link in Oracle 11g Express Edition;
There are two computers: computer-server and computer-client. Tnsnames.ora are the same on both computers ie.
CT =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = krzysztof)(PORT = 1521))
(CONNECT_DATA = (SERVICE_NAME = XE)
I created database link :
Create database link zdalny
Connect to <user_id> identified by <password>
using ‘CT’;
Client can’t connect with server when I am using above command. But when I change “using” for using ‘krzysztof:1521’ or using ‘krzysztof’ or using ‘server IP:1521’ – everything is ok.
Why I am asking. Because in all materials which I am reading about Oracle command with using ‘CT’ should be working correct. But there is not. Do you know, why?
Thanks in advance and apologize for my English.
Rgds
Krzysztof

Krzysztof Szymaniak wrote:
Thanks for all replies.
Below is server's tnsnames.ora
CT =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = krzysztof)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = XE)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
ORACLR_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(CONNECT_DATA =
(SID = CLRExtProc)
(PRESENTATION = RO)
SQL Error: ORA-12154: TNS:could not resolve the connect identifier specified
12154. 00000 - "TNS:could not resolve the connect identifier specifie
Rgds
Krzysztof
PS. I tried with using 'XE' - not working.Assuming that is the correct tnsnames, of course XE is not working. You don't have a tnsnames entry for 'XE'.
You need to be aware that when using a dblink, the client is the db in which the link is defined, not the desktop from which you connect to that database.
I think you need to start here:
http://edstevensdba.wordpress.com/2011/02/26/ora-12154tns-03505/
http://edstevensdba.wordpress.com/2011/02/09/sqlnet_overview/ (Help! I can’t connect to my database )
http://edstevensdba.wordpress.com/2011/02/16/sqlnet_client_cfg/ (Help! I can’t connect to my database (part duex) )
The fact that your client (db link) is a database doesn't change anything taught in the above.

Problems with graphics [link removed]

Hi everyone.
I have problems with graphics [link removed] - Ogłoszenia Hrubieszów. Darmowe ogłoszenia Hrubieszów i okolice. If you want to help, please [link removed] help me in diagnosis. THX !

Explain what exactly the problem is rather than spamming the forum with links. The page looks just fine in Firefox and Chrome.
Mylenium

WRE54G not working with D-Link DIR-655

After having 2 Linksys WRT310N units fail within 14 months, I was given a D-Link DIR-655 to use for my home network. When I originally purchased the WRE-54G for use with the 310N, the signal strength as indicated on a Tivo and PS3 went from 20%-40% range to 70%-85%. These two components are approximately 30 ft horizontally, and 20 ft down vertically from the router.
Upon replacing the router with the DIR-655, both of these units are again registering signal of 20%-40%, as if the WRE-54G is not functioning, and/or the TiVo and PS3 are getting their wireless signal directly from the DIR-655.
I can access the WRE-54G's web interface, can ping it, can see it as active in the DIR-655's interface, and have two solid blue lights. Everything has been powered down and reset multiple times. I have the same issue whether or not the WRE-54G sits inside or outside my DHCP range.
How can I determine if these components are getting signal from the router through the WRE-54G or if they are getting the signal directly from the router and bypassing the WRE-54G, and is there a way to "force" these components to take signal from the WRE-54G?

Hello. Is the D-link an N router? The WRE doesn't really work well with N routers. The ppl that have say that security must be disabled. I think I have read posts that got this working, though. I'm wondering if the WRE is physically on the edge of your signal strength, e.g. if you got the WRE closer to the router it would work better. The only thing that is unusual is that you said you have two solid blue lights. The activity light should be blinking blue. So I guess I don't think the WRE is really doing anything right now, though you have all the indications except for increased signal strength.
As far as forcing the equipment to connect, you'd just have to set up static IP's and say that the WRE IP addy was the gateway, not your router. But I don't think that is the problem as WIFI will connect to the stronger signal if it is present. I just don't think the WRE is repeating the router signal.
Edit: Did a search. See if this post helps:
http://forums.linksysbycisco.com/linksys/board/message?board.id=Range_Expanders&message.id=2611&query.id=16490#M2611
Message Edited by Luckydog on 06-19-2009 03:07 PM

Photosmart D110a Wireless Troubleshooting with D-Link DIR-655 and Mac OSX 10.8

Good evening all,
Apologizes if this has already been posted. I've googled this issue a couple of times, but I still haven't found a solution for this problem.
I have the Photosmart D110a and I'm running Mac OSX Mountain Lion, and my router is a D-Link DIR-655 and my security is WPA-Personal and the router is running in 802.11gn mode. My ISP is Optimum Online.
The issue that I've been having is that the printer works wireless when everything has been recently booted up. As does the scanner. However, if it hasnt been used for a while, the printer shows up in the OSX Print & Scan settings page as idle, but when I try to print, the dialog just says "looking for printer" and never finds it, and just says "The printer is not connected" under the item in the OSX Print Queue. Because of this, I have to restart the computer or restart the printer for them to find each other again.
I've seen other solutions on here, such as giving the printer a static IP address, and this hasn't worked either. The printer is still accessible with the static IP address, which means it's still got a connection to my network, but for some reason the OS isn't recognizing it or something.
It's obvious that the printer works when everything is freshly rebooted, but I still haven't been able to figure out this issue once it's been idle for a while.
Any help would be greatly appreciated!!
Errold

Hi,
Try following my post below, I believe it might be relevant as the router drops the Bonjour connection:
http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/losing-connection-to-airprint-a-few-min...
I would also suggest updating your router's firmware and check if that may help:
http://www.dlink.com/us/en/support/product/dir-655-wireless-n-gigabit-router
For any help with this proccess I would highly recommend contacting Dlink support.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Problem with action links

I have a relatively simple DVD project with 10 movie sequences each placed on a separate timeline. DVD has just one menu with a Button: "Watch whole movie" which basically sequences all 10 clips and then back to the menu.
Then I also have 10 Sequence-Buttons on the menu that should only show the respective sequence and then back to the menu.
1. I set up the action sequence for "Watch the whole movie" m1-m2-m3-m4-m5-m6-m7-m8-m9-m10-menu. No problem with that.
2. When I then start working on the first sequence button "SCENE 1" the problem starts. What I want is just Scene1-back to the menu. I tried it without and with end action override but then I disturbed the m1-m2-m3-m4-m5-m6-m7-m8-m9-m10-menu sequence.
I really couldn't figure out this simple task. Maybe somebody can give me a hint.

1. I set up the action sequence for "Watch the whole movie" m1-m2-m3-m4-m5-m6-m7-m8-m9-m10-menu. No problem with that.
Actually, that is the problem. Instead of making the end action of each timeline the next timeline, create a Playlist and sequence the timelines in there. Your play all button links to the playlist. End action of the playlist is Return to last menu.
Without end actions that go to the next movie, your Scene buttons will work fine. (The end action on each timeline will be "Return to Last Menu."

Problem with subrpt links in crystal reports 8.5 (cr 9 and 2008 installed)

I am trying to add a subreport to an existing CR 8.5 report. I currently have Cr 8.5, cr 9 and cr 2008 on my pc (xp). The subrpt is pointing to a sql 2005 stored procedure that has a parameter (@vvcrCono). When I try to set up the link, the parameter is not listed in the of available parameters to link to. I select a field from the available fields on the main report, hit the > to move it over as a field to link to, and the dropdown that contains the list of parms to link to on the subreport will change to ?pm-(fieldname). I do not see the parm list from the subreport. I am unable to get the link defined. This occurs even when trying to edit an existing subreport.
Is there a problem with running these crystal report versions on the same machine? Or am I just missing something? It has been a while since I've used cr 8.5.

Joanne, thank you for your posted solution and specifically your mention of miniscule scroll bar of the 'subreport parameter field to use' drop down, I had been on several forums but none of them mentioned this, my subreport now accepts the passed parameter and main report works well. Hope your post helps others as it did me, only wish we could include a graphic to illustrate this as I have seen same question posed several times and several different msg boards.

Problem with PDF, link in website doesn't find the adobe

We are using Windows XP, Internet Explorer 8 and Adobe Reader 9.0.
There is a website with a link to open the dokument with adobe. But when we take a klick on this link adobe isn't found. The format of the file is any file and there only cryptical sign in the file, which would be open. Please - I need help!

I have the same problem - shocked that this hasn't been addressed by Adobe or Microsoft. It began with recent updates. Adobe Reader will not open a .pdf file on the web. I sometimes get the following dialog but mostly I get a blank screen with "Done" in the status bar.
If I open a .pdf from my hard drive I get a message about protected mode. If I click on the link in the message, I get Adobe instructions about turning off protected mode - but it is already turned off. If i cancel that message i can open a local .pdf.

Two problems with my linked text

Hi, I am having a couple of problems with my code for a link.
Problem 1
I am trying to get the text "learn more" to be "red" on (main) but it is only showing "red" on (over) or hover. Please tell me how to make the text "red" on (main).
Problem 2
The code seems to be identical for all thumbnails but only the text below the "circled" image seems somewhat correct. I can't figure out why the other text has a link (is linked) when the code is the same as the "circled" code.
http://www3.telus.net/~jessum/holiday pools/index.html

<a href="http://www3.telus.net/~jessum/holiday pools/services.html" target="_self">
Thanks Nancy, so I named my main website folder "holiday pools", (with a "space") I guess this is bad. So in my code (see above) there is a space in "holiday pools".
Question #1
Do you know how can I delete the space or add a underscore without destroying all of my linked pages and images?
Question #2
I read that this (see below) is how I can add comments without it being visible in the browser, so why is this giving me errors?

Problems with D-Link DIR-300

Similar Messages

Maybe you are looking for