Problems with DLed ISO of Audigy 2 Installation

Okay, so i DLed the ISo of the audigy 2 installation CD, mounted it on a CD emulator and it runs fine, but when i get to the point where i need to install the drivers it gives me an error saying i don't have any Audigy 2 Hardware installed on my motherboard. Which i know is false because with other driver updates my card works for the most part.
But i want the media controll center that comes with the CD and want to make use of this ISO, the ISO is the exact same of my CD to the extent it gives me the same exact options for my Audigy 2 regular 6. surround sound. Does anyone else have this problem or had and know what to do from here?
I'm running from a clean re-format and it's a good clean format, this is strictly an ISO or sound card related problem. i'm 99.99% sure it's because of the ISO not detecting my hardware, but i know it's functional and in there. CAN anyone, anyone at all! please for the love of god, i have litterally whimpered to myself and pulled hair out because of this issue! arghhhh someone free me from my audigy 2 prison! anyways lol, any help much appreciated.

If your card is an OEM model, you may need to patch the installer. This is done w/ ctcomp.exe utility --> search this forum after it's name so you get the dl link and some instructions how to patch.
After you have drivers installed, then you can manually install those applications you like to have (may need to have patch those installers too).
jutapaMessage Edited by jutapa on 08-4-2006 0:06 AM

Similar Messages

Problem with Oracle 11g(32 bit) installation on windows 7 ultimate edition

Hello all,
I have a problem with Oracle 11g(32 bit) installation on windows 7 ultimate edition (32 bit).
I have successfully installed it immediately after OS installation. But today, i have decided to deinstall it and go for Oracle 10g version for 32 bit.
Everything went normal during installation, but i can see the services is not present in services.msc. Also its throwing some exception for dbca, netca
Now i tried to deinstall it and again go for 11g. But even the same story here..
Can anybody give me a solution for this..
-Regards
Rajesh Menon

Saqib Alam wrote:
i recently install Oracle 11g R1 on windows 7 ultimate, i installed it and working perfectly.
ur problem is that u install latest version and now u trying to installing old version.
now u need to uninstall 10g and delete oracle from services, if the probleme presist then u should
install fresh windows 7.
Regards
SaqibNo need to install a fresh OS. That's like tearing your house down just because you wired a lamp wrong and blew a circuit breaker.
There are MeaLink notes on how to eradicate an Oracle install from Windows, but it boils down to this:
Stop all Oracle services
In the registery:
- Delete all oracle services from the register (HKLM\SYSTEM\CurrentControlSet
- Delete the entire Oralce folder from HKLM\Software
reboot
Delete the ORACLE_HOME directory and any other Oracle related directories/files. Offhand, it seems like there is an Oracle directory under Program Files.
reboot

"problem with shortcut/fatal error during installation" on other user accts

I-tunes installed and works with no problem in original user, but when another user account attempts to open Itunes, program attempts to install/configure again, then results in a "problem with shortcut / fatal error during installation" message. Setting the other users to administrators doesn't help, nor does un-installing/re-installing, etc. I am at least the 4th person with this problem (see Burthomp earlier today,Jan. 17 and Richard 1018 on Dec. 29). This problem started with Itunes 7.5, and is still a problem on Itunes 7.6. I have a standard Dell setup, Model E510. There must be a lot of people with this problem. Apple, are you working on this? Anyone else have a suggestion?

I ran into the same problem, but I think I have the solution. First, the problem isn't with iTunes, its an access problem with Windows XP. I tried to run the iTunes program from the Program Files, and I received an "Access Denied" error.
If you try to open the Program Files in My Computer\Local Disk(C:) and receive an "Access Denied" Error, that is why you are receiving a "shortcut problem/Fatal Error during installation".
Here is how I corrected it:
1) Shut down the computer and restart it in "safe mode". I had to look up how to do this, but I pressed F8 when it was restarting and I highlighted the "safe mode" and started the machine. The icons will be large, but ignore it.
2) Open a user that has administrative access -- I used the one user that has access to itunes.
3) Go to My Computer\Local Disk (C:) and right click on the "Program Files" folder. Select "properties" at the bottom.
4) Go to the Security Tab
5) At the top you should see one or two users that have access to the Programs File. One will be the user that itunes works on. Click Add, then click Advanced, then click Find Now.
6) At the bottom should appear a list of users. Select a user on which itunes doesn't work. Click Ok, then click OK again.
7) Give that user full access to the Program File by putting a check mark in the Full Access box.
8) Repeat for the remaining users.
9) Restart computer in normal mode.
10) Go into a user that had problems and click the itunes icon, and it should run.
It worked for me, I hope it works for you.

Problems with track pad and osx installation disc on macbok.

Okay so I am having two separate problems with my macbook.
First, the track pad, or the button beneath it, is pretty much completely out of commission. When I try and use it, the computer acts as if I am holding down the button all the time. Example, when I drag it across the desktop, the "click-and-drag" square starts appearing next to the cursor or when move the cursor on an icon, it tries to click and drag that. The only way that I can fix it thus far is to hook up my wireless mouse. Hoping someone else has a better solution so that I can continue to use the notebook on the go without having to bring the mouse. Note: the button does not appear to be depressed in anyway.
Second problem is happening when I attempt to reboot the computer with the OS X Leopard disk in for a re-installation. When the gray start-up screen appears, before the gray apple comes on the middle of the screen, a folder icon with a question mark on it appears for a split second and then turns into the normal apple icon after which my OSX disk is spit out of the drive and the computer boots straight to the desktop. I have attempted holding down the control button, the option button, and starting the process while the computer is still turned on and then just restarting it, the disc is ejected upon restart every time. I have reinstalled the OS with this disk once before and it has worked fine and other disks seem to be working fine in the drive, so I am at a lost here.
I know that was a lot of info but if anyone out there can help me out with either one of these problems it would be much appreciated.
Thanks.

exactly the same issu with the track pad here.
I v tried to use it without the battery but the problem persist.
If I use an USB mouse i can move it arnd but wen I click or double click nothing happen...so is useless.Same problem with the Blur Tooth wireless mouse.
The issue appear several months ago...after a couple of weeks went away, and now is back again. I try the routine manteinance but nothing solved the issue.
Any suggestion? I have some urgent work to do ...I will try tomorrow to bring it in an apple store but I can't leave it with them ..
Thanx in advance

Problems with ASIO on multiple Audigy 2 ZS cards

G'day,
I've been using an Audigy 2ZS PCI for a couple of years now with great success. I convert old audio recordings to various digital formats using a couple of applications (mainly Adobe Audition 1.5 & 2.0).
Recently, my workload has increased to the point where I needed one card to just record at high res, and another card to handle just playback and general Windows bells & whistles without impacting the performance of the recording.
I installed a second 2ZS, it was detected by Windows, etc, and I set it up so Windows uses one card (identified as A800) for all its stuff, and the second card (B000) is used only for ASIO recording.
That's where the nightmare started. I've uploaded and installed the May 2006 Creative driver update, but I still suffer from a number of problems, some related to Audition, some not.
The least annoying problem is that all the Creative drivers seem to identify only a truncated version of the ID string. So for example, in various applications, I see "SB Audigy 2ZS [B0 -1" or "SB Audigy 2ZS [A8 -5". This is annoying but not showstopping.
The biggest problem is getting applications to correctly interact with the Creative Labs ASIO driver and enumerator. Most applications (Nero, Audition, Premiere Pro) can "see" the ASIO driver, but when it's selected, it may not work at all, or may work from one or the other sound card, without any clear indication of which card is selected.
I'm sorry if this sounds generic, but I've spent a week with the Adobe folks, who simply ended up telling me "it's a problem with the CL drivers", and most forums I frequent say the same thing, and the specifics vary from application to application, but at the core, CL drivers are just not working properly with the system when two cards are installed.
By way of example, using ASIO4ALL has fixed many of the card selection problems, but even there, sometimes the inputs of one card are disabled, sometimes the other card, and in the middle of a recording session (line in jack, 44.1k/16 bit), the input waveform slowly biases down to -2V and then all I get are inverted samples - quiet appears as max. value samples, while valid audio appears as -2V samples! If I put the audio line into the other card, it plays just fine (I know what I'm doing WRT grounding and line levels, etc).
This system has run essentially non-stop since September 2005, and I guess it collected a lot of software crud, so I bit the bullet and performed a clean reinstall of Windows XP and updated every driver I could. Some problems have since changed for the better (i.e. clicking on the configure button of the CL ASIO driver no longer bluescreens or displays an empty window), but the problems described above still happen all the time.
I was wondering if other users have seen the same or similar problems, and if so, what has worked for you?
The system is a Gigabyte 81PE1000Pro2, PCI bus, 3.2GHz P4 with HT enabled, 2G physical RAM, and a 1.5Tb RAID disk system.
Recording when a single sound card (either of the cards works beautifully on its own) is perfect; just when both cards are installed, everything gets confused! Even the WDM drivers don't correctly identify or manage the routing of inputs and outputs reliably.
Sorry to go on about this. If anyone can offer constructive suggestions (I define "constructive" as not telling me to "buy another type of card" or (as one poor soul suggested) telling me that multiple PCI sound cards are not supported under Windows), I would be most grateful.
Thanks and regards,
Peter

G'day Jutapa, thanks for looking at this!
Yeah, I got all the possible ASIO drivers listed, one CL ASIO driver is listed for each card, and I have spent much time trying different configurations of card order, I/O port order, direct sound enabling/disabling, timesync enable/disable, etc.
The problem for me with the CL ASIO drivers is that it limits me to 48/96k sampling only. That is not acceptable, because I need to sample at 44.1k for "straight" conversions to CD, or 192k/24-bit for archival purposes (used for extremely old or fragile recordings), so I end up with large files that nearly always need to be resampled to 44.1k, or saved permanently at 192k/24-bit. Typical filesize is 650Mb, largest so far is 5.66Gb - so that's an awful lot of time spent downsampling or pointless upsampling. I'm starting to think that the problems I'm experiencing may be due to sampling at "non-native" ASIO or WDM rates. I haven't tried sampling at 48/96k to see if that "fixes" the problem...
Using the WDM wrapper drivers (I don't know if these are provided - or supported! - by Creative or Adobe) results in randomly disabling one or the other Audigy. At that point, the only way to recover functionality for the disabled card is to reboot. Sometimes only the inputs are disabled, sometimes only the outputs, sometimes both. There is no pattern that I can see or duplicate.
Both cards appear to work fine under Windows. I can define either card as the default recording or playback device, and I can define one card as the default recording and the other as the default playback, any combination works fine. However, any application that uses WDM drivers to access the cards also get confused when a card's inputs suddenly become disabled! This does not appear to happen when Windows is the only application using the cards.
Specifying "use preferred devices" in Windows does disable the non-selected card (or card input or output if I specify different cards for input and output) in other applications.
The problems are much worse when I try to use any ASIO drivers to access the cards. This problem with ASIO appears regardless of the application I use.
I have installed ASIO4ALL, and it finds and configures the cards without any problems in ALL applications - but if I'm recording (with no other applications or drivers or tray applications loaded or active), when I stop recording and restart, the input I was just recording from appears disabled! If I open the ASIO4ALL configuration window, one or both Audigy cards will have their inputs disabled, or both inputs AND outputs disabled. This doesn't happen all the time, and my workaround is not to stop recording once I've started. Not a good workaround! I do realise that ASIO4ALL does fiddle around with the sample rates in the background, but at least when it works, I get a single clean sample without having to do all the resource-intensive resampling later. Maybe it's 6 of one, 1/2 dozen of the other...
I understand and appreciate that perhaps CL never intended to provide software functionality for more than one Audigy on any given PCI bus/bridge. I just don't get why the drivers appear to work natively under Windows (I'm assuming that Windows just uses WDM access) but not with any other applications.
I will try and do some testing with "native" ASIO sample rates (i.e. 48/96k) and see if that fixes some or all of the problems. My concern here is really that my expectation is that the drivers, once identified and enabled, should not suddenly disable themselves in all applications (by whatever mechanism), regardless of what sample rates are specified. But maybe that's too much to expect.
BTW, this happens with any combination of 2 of my 3 Audigy 2ZS cards, each of which works perfectly on its own with ASIO and WDM drivers. So it's definitely a multiple card issue.
The workaround that has been suggested is to purchase a different vendor's card : but there are so few cards that I can use to sample at the resolutions I require, and they are all so bloody expensive, that's why I've committed so much to CL Audigy 2ZS.
I'll get back to you once I've tried a few days working at the "standard" ASIO sample rates. Thanks again for taking the time with this stupid and unusual problem!
Kind regards,
Peter

Has anyone experienced a problem with FB posting since the installation of iOS 6?

Since the installation of iOS 6, I noticed that when I post a photo on FaceBook it does not show that post using my iPad or iPhone. I posted using my iMac and within seconds it showed up on two devices mentioned above. Please help.

Hello,
I am currently an owner of an Ipod Touch 4th generation. I see you are having problems with your Ipod Touch/Ipad/Iphone/Ipod Classic, so I will try to find a solution to your problem.
Do the IOS update (the one that is the latest)
Reset All Settings: SETTINGS>GENERAL>RESET>RESET ALL SETTINGS
Use it until it dies (automatically shuts off)
Plug into Charge
Leave it 1.5 hours or longer after it reaches 100% --> Undisturbed (preferably overnight)
Give it a few days to Calibrate
This has helped me on my Ipod Touch 4th generation, running IOS 6.0.1
Hope that helps!
If none of the above solutions work, can you please respond back ASAP as I will try to find another solution to your problem (This might even help others with the same problem!)
Cheers!
Pizza98704

Problem with 10.3.181.34 Installer

I recently refreshed my Flash install and ran into a strange problem. When I executed the installer named install_flashplayer10ax_gtbd_aih.exe, it deleted itself and never successfully installed. After looking at Procmon, I noticed that it made copies of itself and added _1 to the filename until it hit the limit of the filename length and stopped. Each iteration would be a new process. I compared my system to one that didn't have this problem and I noticed my TEMP and TMP variables were pointing to %systemroot%\temp instead of %userprofile%\temp. After restoring the correct temp variables, the installed completed successfully. I hope this helps somebody who finds this through the Google.

I'm going to memorize that link. I usually never have to time to Google this site until I find a REAL installer for their products instead of links to whatever conten
t caching delivery mechanism they are using this month. I can't tell you how many people I run across with McAfee Security Scanner or a Google toolbar they never use. It will be a good day when Flash isn't the de facto standard for rich media on the internet.

Problems with 10.5.1 Retail Installer CDs?

All:
I installed 10.5 immediately when released, and had several problems with networking and printers (eg it removed all of them when re-installing), etc that were mostly fixed with 10.5.1
I see there are 10.5.1 installer DVD in stores, and have a few more macs to install on at home that I had been waiting on due to my initial problems.
Anyway, anyone having problems with the 10.5.1 DVDs or are things going well?
thanks

No problems here. I installed from a 10.5.1 Family pack onto two Macs. An Intel based Core Duo 2 iMac and a dual 2 Ghz PowerPC G5. Installed and runs without problem on both.
It's unlikely that Apple will produce a 10.5.2 retail disk. Historically, they have never produced a new retail package for every point update. Usually only one or two others above the initial release.

Audio latency problem with VST, SONAR and Audigy 4 PRO

Hello all,
I have a slight problem with audio performance on my computer and I can't isolate what is wrong. I am using Cakewalk SONAR 4 studio edition, and a recently purchased Audigy 4 Pro soundcard. ( I know it's not quite professional grade, but it works well for me) I recently bought some string instruments from the Vienna Symphonic Library. So far, I love the sound of these "virtual instruments" if you will. The problem comes when I try to record them. I get stuttering and dropouts when I try to record the track in Sonar. I've tried the WDM drivers in 16 and 24 bit modes and the ASIO drivers (which apparently only support 16 bit!?) I know Creative has mentioned that these cards can record easily at 24/96 which is what I'd like if possible. Vienna instruments come in a 24 bit format. Is there something I'm doing wrong or do I need to seriously consider a different soundcard? I use Sonar to bring in the Vienna instruments as a VST. I also apply a reverb on it. When I just play this stuff on my MIDI keyboard, it all sounds great and keeps up. The moment I go to record though, I get dropouts after about 15 seconds or so. Also, is there no way to get ASIO 24 bit support for creative's consumer level cards? I'd be happy with the WDM's personally if those would work. I've looked into the KX project as well but haven't had a chance to try their drivers yet. On a different note, what are the significant differences between ASIO and WDM if any at all? (aside from supported bit rates) My current computer setup is quite powerful and I don't use much CPU power at all so I don't think it's my setup. Intel E6700 (2.67Ghz) Core 2 Duo, 2GB DDR2-800, 320GB Seagate SATA in RAID 1, Nvidia 7600GT, and Creative Audigy 4 Pro. Any help, or insight would be greatly appreciated!
Matthew

Audigy 4 Pro should support 24-bit/96 kHz w/ ASIO --> have you selected those I/O drivers in Sonar audio settings (Options-Audio-Drivers -tab). ! You need to unselect all I/O drivers first to get those 24/96 drivers selectable)?
Dropouts comes from various sources. Have you checked if the read/write caching is set properly (Sonar, try different settings)?
Stuttering may come from shared IRQ/resources and PCI Latency settings.
If your graphics card is not PCIe then, make this registry tweak
Run regedit and search the key named as DisableProgPCILatency
- set all 'DisableProgPCILatency' key values to 1 (HEX or DEC) (1 = disabled, 0 = enabled)
- boot to BIOS settings and find the "PCI latency timer" option --> set its value to 32 or 64 (this is global PCI latency setting)
- reboot
and check the IRQ situation. If there are IRQ shares between Audigy and other devices/controllers, try to get those fixed by disabling unneeded controllers/devices or by moving the Audigy into another PCI slot (PCI slots #3 and #4 are normally not shared).
Couple meaninful differences between WDM/KS and ASIO are;
- you can't get latency lower than 10 ms w/ WDM/KS (well, you can in Sonar by manually editing those buffer values but, the result is not good when you go under 10 ms buffer values (buffersize / samplerate * 1000 = latency in ms --> 512/96000*1000=5.33ms)
and
- you can record from one stereo (you can split this to two mono) source at a time w/ WDM (recording source is set in CT Surround Mixer (or windows recording controls))
- ASIO supports (Audigy serie) locked 'resolutions' only - 16/48 or 24/96
Also, tweak your system for music - http://www.musicxp.net/
Some information on CT ASIO -
http://forums.creative.com/creativel...essage.id=1726
jutapa
Message Edited by jutapa on 12-17-200606:01 PM

Is anyone else having problems with large files, such as installation images, becoming corrupted when downloaded in Mavericks using Safari?

I am finding that when I try to download a disk image file, such as Office 2011, it reads invalid checksum, is corrputed and will not install. I tried to download it several times and even unchecked in the Disk Utility Preference Pane to verify checksums. The way I solved the problem, was to go to my Windows Machine and download the image, put it on a USB flash drive and install it on my Mac from the stick. Not a proper solution, but it did work. Has anyone out there had this problem? This is applying to any large .dmg files not just Office 2011.

I'm having exactly the same problem with the dmg file for Office 2011, tried downloading from my windows machine with no luck, still having the invalid checksum message.

Installation Problem with my Sound Blaster Audigy Li

I own a Win XP 64 bit Edition and want to install my soundcard.
But there is no driver for my Soundblaster.
Please help, the Model Number is SB000.
Cause i installed linux next to windows i saw, that it is identified as an SB Li've! 5. so i downloaded that 64 bit driver.
The Installer runs throw the process, but there does not appear any WHQL message or anything.
After reboot there is still no SB installed.
Please help me.Message Edited by Good_Will_Hear on 07-27-2006 2:7 PM

Got one right >here, but it's a Beta driver. Meaning, it may or may not work, and it's unsupported. Your sound card is a Li've! 5., which wasn't really designed for x64.
Good luck!
DaleMessage Edited by Dale-CL on 07-27-2006 02:4 PM

Problem with HP LaserJet M1319f MFP installation

Dear support team and community members,
I'm currently trying to install HP LaserJet M1319f MFP connected by USB on Lenovo Q190 machine /Intel Core i3 processor/ running freshly installed Windows 7 Enterprise 64 bit with Bulgarian
language pack, all current updates, Microsoft Forefront Protection /I also tried to disable the Real-time protection/, UAC disabled, administrator account, IE 11, .NET Framework 4.5.1.
The priter was working correctly with Windows XP.
I downloaded the driver package from the official hp website.
After the installation process reach the "Copying files to the hard drive" stage the installer return error Printer Software Installer stopped working.
I tried running with Administrator privileges and/or Windows XP SP3 compatibility mode, but the same error occurs.
I tried Microsoft Fix It software for install/uninstall drivers too,but with no luck either.
I cleaned the cashe and temporary files around 10-15 times.
Windows update is not helping with the drivers too.
I tried to extract the files from the installer and manually add the printer and got error that the installation was not successful and below it says The file was not found /if I recall it correctly/
After that I tried HP Print and Scan Doctor software, but it displays that there is no driver installed and redirecting me to the driver download page.
I tried the Driver Wizard software too, but it returns that this model is no supported.
I tried to change the windows startup to "Selective startup" with "Load startup items" unchecked and all non-microsoft services disabled, but with no success.
Under Safe mode the install won't complete because of the Print Spooler service not running, which is running normally otherwise.
The "ntprint.inf" file is present in the "Windows\inf" folder, the registry HKLM\SYSTEM\CurrentControlSet\Control\Print\Enviroments\Windows NT x86 has only Drivers and Print
Processors subkeys and the registry HKLM\SYSTEM\CurrentControlSet\Control\Print\Monitors has only Local Port, Microsoft Shared Fax monitor, Standard TCP/IP Port, USB monitor and WSD port subkeys.
The folders Windows\System32\spool\PRINTERS and Windows\System32\spool\drivers\W32X86 are empty.
I ran sfc /scannow in cmd with administrator privileges, but there was no integrity violations.
I tried to disable the IE component, but no luck either.
So now I’m out of any ideas how to connect that **bleep** thing… I hope that someone can help me with this issue.
Currently the devices without installed driver in the Device Manager are "Hewlett-PackardHP LaserJet M1319f MFP" /Hardware IDs USBPRINT\Hewlett-PackardHP_La28A1 and Hewlett-PackardHP_La28A1/
and HP Scan /Hardware IDs USB\VID_03F0&PID_5817&REV_0100&MI_00 and USB\VID_03F0&PID_5817&MI_00/
I forgot to mention that I tried all kind of variations with these solutions with and without printer plugged in.
Thank you very much in advance for any kind of guidelines.
Best regards,
Ivan

Hello Rick,
Just as I mentioned above I'm using Microsoft Forefront Protection, but had no luck with disabling the Real-time protection - it is disabled,
but that chanage nothing.
The downloaded driver is for Windows 7 64 bit.
I did write to HP but I still got no answer from them... I already checked that support page, but I didn't get any information corresponding
to my problem, not to mention that a lot of that page is just copy/paste from another product and it's not relevant to that model.

Problem with services of SAP after installation of ABAP on MS SQL server

Hi,
I am trying top install 2004 Netweaver ABAP+ JAVA on my machine
Following is my machine configuration -
Machine type - Windows 2003 Standard Edition SP1
Machine name - pun-idmqa-vm1
SAP Instance name - QSA
DB type - MS SQL 2000 SP4 + hotfixes and instcoll.exe is executed. After nstalling SQL shows server proper as SQL_Latin1_General_CP850_BIN2 collation
Message port - 3600
I could sucessfully install Database from CD and thereby could sucessfully install ABAP. During postinstall I tried to start the server. all the following services got up -
msg_server.exe
disp+work.exe
igswd.exe
But after some time 2nd service goes down. Following is the error message flashed in
trc file: "dev_disp", trc level: 1, release: "640"
Mon Jul 02 16:33:16 2007
kernel runs with dp version 128000(ext=102000) (@(#) DPLIB-INT-VERSION-128000-UC)
length of sys_adm_ext is 524 bytes
systemid   560 (PC with Windows NT)
relno      6400
patchlevel 0
patchno    31
intno      20020600
make:      multithreaded, Unicode
pid        2492
***LOG Q00=> DpSapEnvInit, DPStart (00 2492) [dpxxdisp.c   1100]
Mon Jul 02 16:33:17 2007
     shared lib "dw_xml.dll" version 31 successfully loaded
     shared lib "dw_xtc.dll" version 31 successfully loaded
     shared lib "dw_stl.dll" version 31 successfully loaded
     shared lib "dw_gui.dll" version 31 successfully loaded
Mon Jul 02 16:33:21 2007
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 4 seconds
***LOG GZZ=> 1 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 3886]
MtxInit: -2 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: JAVA is not active
DpShMCreate: sizeof(wp_adm)          10528     (1316)
DpShMCreate: sizeof(tm_adm)          2780232     (13832)
DpShMCreate: sizeof(wp_ca_adm)          24000     (80)
DpShMCreate: sizeof(appc_ca_adm)     8000     (80)
DpShMCreate: sizeof(comm_adm)          290000     (580)
DpShMCreate: sizeof(vmc_adm)          0     (372)
DpShMCreate: sizeof(wall_adm)          (38456/34360/64/184)
DpShMCreate: SHM_DP_ADM_KEY          (addr: 054B0040, size: 3192688)
DpShMCreate: allocated sys_adm at 054B0040
DpShMCreate: allocated wp_adm at 054B1B58
DpShMCreate: allocated tm_adm_list at 054B4478
DpShMCreate: allocated tm_adm at 054B44A0
DpShMCreate: allocated wp_ca_adm at 0575B0E8
DpShMCreate: allocated appc_ca_adm at 05760EA8
DpShMCreate: allocated comm_adm_list at 05762DE8
DpShMCreate: allocated comm_adm at 05762E00
DpShMCreate: allocated vmc_adm_list at 057A9AD0
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 057A9AF8
DpShMCreate: allocated wall_adm at 057A9B00
MBUF state OFF
EmInit: MmSetImplementation( 2 ).
Mon Jul 02 16:33:22 2007
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation std
<EsNT> Memory Reset enabled as NT default
<EsNT> EsIUnamFileMapInit: Initialize the memory 1132 MB
<ES> 1131 blocks reserved for free list.
ES initialized.
Mon Jul 02 16:33:36 2007
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 2.6.1 2.6 4.0) [dpxxdisp.c   1462]
Mon Jul 02 16:33:38 2007
***LOG Q0K=> DpMsAttach, mscon ( pun-idmqa-vm1) [dpxxdisp.c   9719]
Mon Jul 02 16:33:46 2007
CCMS: start to initalize 3.X shared alert area (first segment).
DpMsgAdmin: Set release to 6400, patchlevel 0
Mon Jul 02 16:33:47 2007
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c   1025]
DpMsgAdmin: Set patchno for this platform to 31
Release check o.K.
Mon Jul 02 16:34:20 2007
ERROR => W0 (pid 2740) died [dpxxdisp.c   12170]
ERROR => W1 (pid 3736) died [dpxxdisp.c   12170]
my types changed after wp death/restart 0xbf --> 0xbe
ERROR => W2 (pid 3876) died [dpxxdisp.c   12170]
my types changed after wp death/restart 0xbe --> 0xbc
ERROR => W3 (pid 3896) died [dpxxdisp.c   12170]
my types changed after wp death/restart 0xbc --> 0xb8
ERROR => W4 (pid 3852) died [dpxxdisp.c   12170]
ERROR => W5 (pid 2008) died [dpxxdisp.c   12170]
my types changed after wp death/restart 0xb8 --> 0xb0
ERROR => W6 (pid 3776) died [dpxxdisp.c   12170]
my types changed after wp death/restart 0xb0 --> 0xa0
ERROR => W7 (pid 4052) died [dpxxdisp.c   12170]
my types changed after wp death/restart 0xa0 --> 0x80
DP_FATAL_ERROR => DpWPCheck: no more work processes
DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
killing W0-2740 (SIGUSR2)
ERROR => DpWpKill(2740, SIGUSR2) failed [dpxxtool.c   2468]
killing W1-3736 (SIGUSR2)
ERROR => DpWpKill(3736, SIGUSR2) failed [dpxxtool.c   2468]
killing W2-3876 (SIGUSR2)
ERROR => DpWpKill(3876, SIGUSR2) failed [dpxxtool.c   2468]
killing W3-3896 (SIGUSR2)
ERROR => DpWpKill(3896, SIGUSR2) failed [dpxxtool.c   2468]
killing W4-3852 (SIGUSR2)
ERROR => DpWpKill(3852, SIGUSR2) failed [dpxxtool.c   2468]
killing W5-2008 (SIGUSR2)
ERROR => DpWpKill(2008, SIGUSR2) failed [dpxxtool.c   2468]
killing W6-3776 (SIGUSR2)
ERROR => DpWpKill(3776, SIGUSR2) failed [dpxxtool.c   2468]
killing W7-4052 (SIGUSR2)
ERROR => DpWpKill(4052, SIGUSR2) failed [dpxxtool.c   2468]
NiWait: sleep (10000 msecs) ...
NiISelect: timeout 10000 ms
NiISelect: maximum fd=1629
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Jul 02 16:34:30 2007
NiISelect: TIMEOUT occured (10000 ms)
dump system status
Workprocess Table (long)               Mon Jul 02 11:04:30 2007
========================
No Ty. Pid      Status Cause Start Err Sem CPU    Time Program Cl User         Action                    Table
0 DIA     2740 Ended         no      1   0             0
1 DIA     3736 Ended         no      1   0             0
2 UPD     3876 Ended         no      1   0             0
3 ENQ     3896 Ended         no      1   0             0
4 BTC     3852 Ended         no      1   0             0
5 BTC     2008 Ended         no      1   0             0
6 SPO     3776 Ended         no      1   0             0
7 UP2     4052 Ended         no      1   0             0
Dispatcher Queue Statistics               Mon Jul 02 11:04:30 2007
===========================
--------++++--
+
Typ
now
high
max
writes
reads
--------++++--
+
NOWP
0
3
2000
10
10
--------++++--
+
DIA
5
5
2000
5
0
--------++++--
+
UPD
0
0
2000
0
0
--------++++--
+
ENQ
0
0
2000
0
0
--------++++--
+
BTC
0
0
2000
0
0
--------++++--
+
SPO
0
0
2000
0
0
--------++++--
+
UP2
0
0
2000
0
0
--------++++--
+
max_rq_id          13
wake_evt_udp_now     0
wake events           total     9, udp     7 ( 77%), shm     2 ( 22%)
since last update     total     9, udp     7 ( 77%), shm     2 ( 22%)
Dump of tm_adm structure:               Mon Jul 02 11:04:30 2007
=========================
Term    uid man user    term   lastop mod wp ta   a/i (modes)
Workprocess Comm. Area Blocks               Mon Jul 02 11:04:30 2007
=============================
Slots: 300, Used: 1, Max: 0
--------++--
+
id
owner
pid
eyecatcher
--------++--
+
0
DISPATCHER
-1
WPCAAD000
NiWait: sleep (5000 msecs) ...
NiISelect: timeout 5000 ms
NiISelect: maximum fd=1629
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Jul 02 16:34:35 2007
NiISelect: TIMEOUT occured (5000 ms)
Shutdown server ...
DpModState: buffer in state MBUF_PREPARED
NiBufSend starting
NiIWrite: write 110, 1 packs, MESG_IO, hdl 3, data complete
MsINiWrite: sent 110 bytes
MsIModState: change state to SHUTDOWN
DpModState: change server state from STARTING to SHUTDOWN
Switch off Shared memory profiling
ShmProtect( 57, 3 )
ShmProtect(SHM_PROFILE, SHM_PROT_RW
ShmProtect( 57, 1 )
ShmProtect(SHM_PROFILE, SHM_PROT_RD
DpWakeUpWps: wake up all wp's
Stop work processes...
Stop gateway
killing process (3832) (SOFT_KILL)
Stop icman
killing process (3960) (SOFT_KILL)
Terminate gui connections
[DpProcDied] Process lives (PID:3832 HANDLE:1600)
waiting for termination of gateway
NiWait: sleep (1000 msecs) ...
NiISelect: timeout 1000 ms
NiISelect: maximum fd=1629
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Jul 02 16:34:36 2007
NiISelect: TIMEOUT occured (1000 ms)
Mon Jul 02 16:34:37 2007
[DpProcDied] Process died (PID:3832 HANDLE:1600)
[DpProcDied] Process died (PID:3960 HANDLE:1588)
DpHalt: cancel all lcom connections
MPI CancelAll 2 -> 0
MPI DeleteAll 2 -> 0
NiIMyHostName: hostname = 'pun-idmqa-vm1'
AdGetSelfIdentRecord: >                                                                           <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 4 (AD_STARTSTOP), ser 0, ex 0, errno 0
DpConvertRequest: net size = 163 bytes
NiBufSend starting
NiIWrite: write 562, 1 packs, MESG_IO, hdl 3, data complete
MsINiWrite: sent 562 bytes
send msg (len 110+452) to name          -, type 4, key -
detach from message server
***LOG Q0M=> DpMsDetach, ms_detach () [dpxxdisp.c   9945]
NiBufSend starting
NiIWrite: write 110, 1 packs, MESG_IO, hdl 3, data complete
MsINiWrite: sent 110 bytes
MsIDetach: send logout to msg_server
MsIDetach: call exit function
DpMsShutdownHook called
NiSelClear: removed hdl 3 from selectset
MBUF state OFF
AdGetSelfIdentRecord: >                                                                           <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
blks_in_queue/wp_ca_blk_no/wp_max_no = 1/300/8
LOCK WP ca_blk 1
make DISP owner of wp_ca_blk 1
DpRqPutIntoQueue: put request into queue (reqtype 1, prio LOW, rq_id 19)
MBUF component DOWN
NiBufClose: clear extensions for hdl 3
NiBufSetStat: bufstat of hdl 3 changed from OK to OFF
NiICloseHandle: shutdown and close hdl 3 / socket 1608
MsIDetach: detach MS-system
Mon Jul 02 16:34:38 2007
EsCleanup ....
***LOG Q05=> DpHalt, DPStop ( 2492) [dpxxdisp.c   8478]
Good Bye .....
I am new to SAP EP installation. Please help me regarding this issue.
Thanks and Regards,
Smitha

forgot to tell you, after that probably you will need to make the installation again.
good luck.

Problem with oracle 10g express edition installation on linux(opensuse)

This is the error it give's me when i install the software. The error come after i set http port and the acces port to database
sed: can't read /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/network/admin/listener.ora: No such file or directory
sed: can't read /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/network/admin/listener.ora: No such file or directory
/bin/chown: cannot access `/usr/lib/oracle/xe/app/oracle/product/10.2.0/server/network/admin/listener.ora': No such file or directory
sed: can't read /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/network/admin/tnsnames.ora: No such file or directory
sed: can't read /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/network/admin/tnsnames.ora: No such file or directory
/bin/chown: cannot access `/usr/lib/oracle/xe/app/oracle/product/10.2.0/server/network/admin/tnsnames.ora': No such file or directory
sed: can't read /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/scripts/postDBCreation.sql: No such file or directory
/bin/chown: cannot access `/usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/scripts/postDBCreation.sql': No such file or directory
sed: can't read /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/scripts/DatabaseHomePage.sh: No such file or directory
/bin/chown: cannot access `/usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/scripts/DatabaseHomePage.sh': No such file or directory
sed: can't read /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/scripts/readonlinehelp.sh: No such file or directory
/bin/chown: cannot access `/usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/scripts/readonlinehelp.sh': No such file or directory
Configuring Database...grep: /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/log/*.log: No such file or directory
Done
/bin/chmod: cannot access `/usr/lib/oracle/xe/oradata/XE': No such file or directory
/bin/chmod: cannot access `/usr/lib/oracle/xe/oradata/XE': No such file or directory
Starting Oracle Database 10g Express Edition Instance...Done
Installation Completed Successfully.
To access the Database Home Page go to "http://127.0.0.1:8081/apex"
The files exists to the path who is looking for them and tell me they don't exist
can you help me please with this problem?
Thanks
Message was edited by:
user652409

hi,
i've reinstalled the database and now it give's me just the last 3 error messages,and i don't now what to do :
Configuring Database...grep: /usr/lib/oracle/xe/app/oracle/product/10.2.0/server/config/log/*.log: No such file or directory
Done
/bin/chmod: cannot access `/usr/lib/oracle/xe/oradata/XE': No such file or directory
/bin/chmod: cannot access `/usr/lib/oracle/xe/oradata/XE': No such file or directory
this files or directories doesn't exists...
Please help
Teero

Problem with charset ISO-8859 with dinamic action

Hello
I migrated my application that was Apex 3.2, and now Apex is 4.2.3, but a have a problem when I'm use Dynamic Action with ISO-8859.
When I used a filter "ação" in dinamic action filter mounted by the apex presents 'aÃ § Ã £ o.'
If I force use of PlsqlNLSLanguage = BRAZILIAN PORTUGUESE_BRAZIL.UTF8 in Dads, works correct.
Please, Help me! I need to keep ISO-8859!
Thanks

Using another example to illustrate the problem… I
found an apparent solution using "encodeURI".
It sees:
quote:
BEFORE:
function SaveMsg()
if (document.sender.message == "" )
return false;
var mensagem=document.sender.message.value;
ds2.setURL('responsexml.asp?action=add'&msg='+mensagem);
ds2.loadData();
document.sender.message.value="";
document.sender.message.focus();
When the entrance of the changeable "mensagem" was
“João” was recorded in archive XML as
“Joo” ...
input: "João"
output: "Joo"
quote:
AFTER:
function SaveMsg()
if (document.sender.message == "" )
return false;
var mensagem=encodeURI(document.sender.message.value);
ds2.setURL('responsexml.asp?action=add'&msg='+mensagem);
ds2.loadData();
document.sender.message.value="";
document.sender.message.focus();
Now ...
input: "João"
output: "João"
This would be a good solution? I will not have problems,
right? Some opinion/suggestion on this solution?

Problems with DLed ISO of Audigy 2 Installation

Similar Messages

Maybe you are looking for