Problems with Ethernet controller and PCI device driver on Satellite L30-10X

Hellow!
Sorry for my bad English, I'm from Russia.
Just few days ago I bought Satellite L30-10X with W Vista on board. My opinion, that this OS does't very good on this computer, so I install W XP.
I have some problems with drivers. At first, I dont know what model I have:PSL30 or PSL33? I download all drivers for both models. But, after installation, computer doen't find drivers for Ethernet controller and PCI device...

Hi
Satellite L30-10X belongs to the PSL33E series. This number can be found on the label placed on the bottom of the unit!
You have to choose this number from the driver download form to get the compatible XP drivers.
I dont know why you are not able to install the LAN driver. Ive got the same notebook with Vista and Ive installed the XP and all drivers run fine.
I assume you have installed the drivers in wrong order. Please take the look in the Toshiba installation instruction txt file. In this order you have to install the driver! Its important.
I think you should install the XP again to ensure the clean registry and then download and install the compatible XP drivers like mentioned in the installation instruction file.
Good luck

Similar Messages

Network controller and pci device driver missing for Toshiba Sattelite c55t b5109

After resetting windows 8.1, I only my ethernet works and I cant turn my wifi. I looked in the device manger, and under "unknown devices" are listed Network Controller and PCI Device with yellow alerts near them. I know that these are related to the wireless card, but everytime I try to update them they say that there is no driver for them.
These are their hardware id's:
Network Controller:
PCI\VEN_168C&DEV_0036&SUBSYS_083211AD&REV_01
PCI\VEN_168C&DEV_0036&SUBSYS_083211AD
PCI\VEN_168C&DEV_0036&CC_028000
PCI\VEN_168C&DEV_0036&CC_0280
PCI Device:
PCI\VEN_10EC&DEV_5229&SUBSYS_F91B1179&REV_01
PCI\VEN_10EC&DEV_5229&SUBSYS_F91B1179
PCI\VEN_10EC&DEV_5229&CC_FF0000
PCI\VEN_10EC&DEV_5229&CC_FF00
PLEASE HELP!!!!

search your laptop for the Toshiba application installer, open it and use it to install your Wireles lan driver.
The application installer is easier than guessing which one you need from your support page.
OR
Your support page is here - http://support.toshiba.com/support/modelHome?freeText=1200008391
You can select the drivers tab then down the page on the left hand side select Windows 8.1 64 bit to narrow down the drivers for your operating system. Then also select Wifi and the available drivers will be displayed.
If you are getting a corrupted system after a reset your hard drive may be failing or your recovery partition may have been corrupted . Create your recovery media if you have not done so already.
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

HP 14-d017AU: Issues with Webcam, Network, Ethernet, VGA and PCI Device drivers

I downgraded my new HP 14-d017AU to Windows 7, 64-bit. Since then I have not been able to find drivers for Webcam, Network, Ethernet, VGA and PCI Device. The Hardware IDs are as follows: Ethernet Controller: PCI\VEN_10EC&DEV_8136&SUBSYS_2191103C&REV_07Network Controller: PCI\VEN_168C&DEV_0036&SUBSYS_217F103C&REV_01PCI Device: PCI\VEN_10EC&DEV_5229&SUBSYS_2191103C&REV_01Universal Serial Bus (USB) Controller: PCI\VEN_1022&DEV_7814&SUBSYS_2191103C&REV_01Standard VGA Graphics Adapter: PCI\VEN_1002&DEV_9834&SUBSYS_2191103C&REV_00I will be grateful for your assistance.

Hi: See if this works... Graphics: Install and reboot. http://support.amd.com/en-us/download/mobile?os=Windows%207%20-%2064 USB 3: Install both of these and reboot. http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_137148_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133037_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken Wireless: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswItem%253Dob_128686_1&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken PCI dev: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133237_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken Ethernet Controller: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133348_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken Webcam: (won't work until the graphics driver is properly installed). http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131219-1&cc=us&dlc=en&lc=en&os=4158&product=6825117&sw_lang=

Need right Win7 display driver for Satellite L30-10X

Hello,
I just reinstalled Windows 7 in my girlfriends Satellite L30-10x and I cant get the gpu to work, it seems like a driver problem, but even in device manager I cant even see the ati graphic card, all it says is standard VGA graphic card as if windows cant find it.
I know that Toshiba dont support windows 7 for this model, but before it was working perfect.
Please help me, I dont know what to do.
Thanks in advance
Miles

Hi
The notebook is really old so I dont think you will find Win 7 drivers on the Toshiba driver page.
The GPU seems to be ATi Radeon Xpress 200 (RC410MD)
It seems the ATI does not provide the Win 7 drivers for this GPU. But I found a solution:
1. open the control panel -> appearance and personalization -> display -> screen resolution
2. click on the advanced settings tab -> adapter tab -> properties -> drivers tab
3. click update driver -> search automatically
4. Windows 7 will find and install a driver for your ATI mobility xpress 200
5. restart computer when prompted

Missing Drivers for USB Controllers (2), SM Bus Controller, and PCI Device

Just got this laptop from my grandparents, and they whiped the OS off if it and did a reinstall with windows 7 64 bit. When it reinstalled it was missing many of the drives, most of which I've been able to find, but I still have four left that I can't find anywhere. Device: Hardware ID PC Device: PCI\VEN_10EC&DEV_5209&SUBSYS_1805103C&REV_01
PCI\VEN_10EC&DEV_5209&SUBSYS_1805103C
PCI\VEN_10EC&DEV_5209&CC_FF0000
PCI\VEN_10EC&DEV_5209&CC_FF00 SM Bus Controller: PCI\VEN_1022&DEV_780B&SUBSYS_358B103C&REV_13
PCI\VEN_1022&DEV_780B&SUBSYS_358B103C
PCI\VEN_1022&DEV_780B&CC_0C0500
PCI\VEN_1022&DEV_780B&CC_0C05 Universal Serial Bus (USB) Controller: PCI\VEN_1022&DEV_7812&SUBSYS_358B103C&REV_03
PCI\VEN_1022&DEV_7812&SUBSYS_358B103C
PCI\VEN_1022&DEV_7812&CC_0C0330
PCI\VEN_1022&DEV_7812&CC_0C03 Universal Serial Bus (USB) Controller: PCI\VEN_1022&DEV_7812&SUBSYS_358B103C&REV_03
PCI\VEN_1022&DEV_7812&SUBSYS_358B103C
PCI\VEN_1022&DEV_7812&CC_0C0330
PCI\VEN_1022&DEV_7812&CC_0C03 I have tried uninstalling the devices and rebooting the laptop, and updating the drivers using this site (suggested for someone else having the same issue) http://support.amd.com/en-us/download. When I looked on hp's site there is no driver that I saw for any of these.

Are you using drivers from your Support page? The AMD graphics driver usually has sm bus and usb drivers. The PCI device is Realtek Card Reader, also in the list. You can also order Recovery Media which reinstalls Windows and all drivers & software. http://support.hp.com/us-en/drivers/selfservice/HP-Pavilion-dv6-6c00-Entertainment-Notebook-PC-series/5191856/model/5210864#Z7_3054ICK0KGTE30AQO5O3KA30R1 Too bad your grandparents didn't use HP Recovery Manager installed on the laptop to reinstall Windows. That would have prevented this.

Having problems with front row (and the opticle drive)

I bought my macbook three days ago, and I'm already having problems. First off, I transfered music from my user profile on my old iMac G5 to the macbook via data DVD. My music collection had some purchaces from the itunes store, so I had to go through the authorization thing, and I can now play them just fine in the iTunes library, but the problem is, if I try to use the front row program to play my purchaced music, I get the message saying that I have to authorize it first. What the ****? Does anybody else have this problem? Also, like many other macbook users, I'm having problems with the opticle drive, such as getting cds to be recognized and other things of that nature.

I noticed that this problem started after I tried to use a software to unlock my drive's region...
I believe this is the problem. The VLC Media Player will usually play DVDs from other regions without changing the settings on your optical drive. You may need to reset your optical drive's firmware back to the original setting, make sure you have the region set for the one you'd prefer to use the most and then use VLC to play the other DVDs.
-Doug
P.S. After two years in the Front Row forum, I'm not sure I've ever heard of anyone playing HDDVD_TS folders with Front Row. I'm not saying it won't work, but I'm not sure it's really supported either. I do have DVD Studio Pro myself, but I'll have friends or family staying with me for nearly the next month, so my evenings and weekends will be a bit full to try making one up for testing...

Problems with time machine and external hard drive

Hi all
In 2009 with my imac I bought a WD external hard drive which the computer says is 148GB formatted. I recall that the hard drive contained folders with files for the running of the hard drive when I bought it - and after it had been plugged in to a mac and used as a time machine, it no longer worked on windows computers.
Now I have used 195 GB on my computer's internal hard drive and wish to stop using the external hard drive as a time machine and instead use it for swapping files between computers and the like.
How can I wipe the time machine back ups and start using it as per usual again? do i need to obtain the WD files from somewhere?
thanks in advance
Nick

Hi Nick,
Avoid the WD files completely, not needed & often a problem.
You need to erase the Drive, & to use it on both Format it MS-DOS/FAT32, on the Mac or PC, but will have a 4 GB filesize limit, as well as other limitations.
One option not mentioned yet is MacDrive for your PCs... allows them to Read/Write & Format HFS+, so no need to reformat it...
http://www.mediafour.com/products/macdrive/

Problems with iMac G5 and LaCie external drives

I have an early iMac G5 (without iSight), running OS 10.5.2. I've had a 250GB LaCie external hard drive for about a year now, and it worked fine up until a couple weeks ago, when I got this message:
Disk Repair
The disk "External HD" was not repairable by this computer. It is being made available to you with limited functionality. You must back up your data and reformat the disk as soon as possible."
I was unable to save anything to the drive after this, including altering files already on the drive. Long story short, I bought another LaCie drive, because I needed more space anyway. I got the 500 GB model, moved everything onto it, erased the old drive, and then I had two working drives. I've since only been using the new drive, but just a few days later, I got the same message again, and am having the same problem, but this time for the new drive. I'm not a computer-savvy person, so I have no idea what could be causing this. This happened not long after updating to OS 10.5 from 10.4 - I'm not sure if this could be related. Can anyone help?

One thing to look out for is the power source. If you have a huge octopus of power cords plugged into one outlet, the drive may not be getting enough power to operate properly. That would explain why the same thing happened on two separate drives, both recently. You may have added something new to the +power strip+ that is overtaxing the available power draw.
Someone I know had this issue. It never occurred to him or me to consider this possibility. His external drive was regularly getting disk directory errors. I initially thought the drive was going bad, but once we distributed the power cords to two power strips connected to different outlets, the problem did not recur.
Your problem may be something else, but it sounded too familiar to not mention my experience with the power cord octopus monster.

[Vista x64] Microphone problems with X-Fi and 2.15 drive

Hi guys,?I'm having a problem with the 2.5 drivers on my X-Fi Platinum card, under Vista x64. It seems the microphone inputs (both on the card and on the breakout box) have problems, any recordings stutter and pop rapidly, making any recordings (or voice chat)?quite useless. This issue doesn't occur with the 2.3 drivers. Is there any known solution to this problem yet?My system: e6600 CPU, Asus P5W-DH motherboard (975X chipset), 4GB RAM, 8800GTX, X-Fi Platinum. Thanks.

hey Darkman,
since I never had this problem with installing this software, I cant really tell whats wrong, but you dont need it anyway to use the x-fi.
but you may want to try one thing, since it crashes at 27% something may still be in use, so check your task manager and close everything that has CT in its name. then try reinstalling again. If that still doesnt work, try to empty your temp folder, its located in documents and settings/user you are/local settings/temp
if that still doesnt work, try maybe something stupid, wait a bit longer than usual and keep the install window in the front to watch the process, maybe your pc is just a bit slowed down by other software so it may take longer than normal

Problems with itunes 10 and external hard drive

Hi
I was recently forced to change the internal hard drive on my G5 Tower, and the external hard drive where I keep my music library.
The new external drive had all my music files copied to it. I reloaded my itunes library files (that I had backed up from old computer) into my music folder and I named the new external drive as the media folder in Itunes preferences. The first time I used itunes it asked me if I wanted it to locate all files to which I pressed OK. itunes quickly found the majority of files and I cleaned up / organized the small mess left behind.
Trouble is a few problems have occurred. Firstly, itunes seems slow – there’s a sluggish pause flicking between tracks – where as before it used to snap into response. Occasionally I’m asked to locate files which I thought was a task it had already done - and every now and again when I check the external hard drive music library I find files have been moved from there album locations to ‘untitled’ folders, etc. I can only assume itunes is doing this. I’ve also noticed I can’t remove the external hard drive from the desktop without closing itunes first which never happened before.
This is getting somewhat frustrating. Can anybody advise?
Much appreciated.
K

Hi Nick,
Avoid the WD files completely, not needed & often a problem.
You need to erase the Drive, & to use it on both Format it MS-DOS/FAT32, on the Mac or PC, but will have a 4 GB filesize limit, as well as other limitations.
One option not mentioned yet is MacDrive for your PCs... allows them to Read/Write & Format HFS+, so no need to reformat it...
http://www.mediafour.com/products/macdrive/

Problem with LocationAPI (JSR179) and Siemens device

In my Midlet i used the following code:
class loc extends Midlet{
public void startApp()
          Form f=new Form("Waiting...");
          f.append("Finding for location...");
          f.addCommand(cOK);
          f.setCommandListener(this);
          Display.getDisplay(this).setCurrent(f);
          try{
               Criteria c=new Criteria();
               c.setHorizontalAccuracy(1000);
               c.setVerticalAccuracy(1000);
               c.setPreferredPowerConsumption(Criteria.POWER_USAGE_LOW);
               LocationProvider lp=LocationProvider.getInstance(c);
               f.append(found(lp)+" location provider");
               Location loc=lp.getLocation(60);
               f.append(found(loc)+"location");
               QualifiedCoordinates qc=loc.getQualifiedCoordinates();
               f.append("Alt: "+qc.getAltitude());
               f.append("Lat: "+qc.getLatitude());
               f.append("Long: "+qc.getLongitude());
          }catch(Exception e)
               f.append("Exception: "+e);
          try{Thread.sleep(5000);}catch(Exception e){}
Everything works on WTK emulator (form shows Alt:0 Lat:0 Long:0).
But when I try this on my Siemens S65, the location provider always is null.
I've tried to play with location permissions and criteria, but always the same result is.
What did i wrong? Could anyone help me?
Thanks

Maybe your cell phone provider doesn't support the location functions...
jc

Problem with Time Capsule and wireless devices

Hi, I have a 1TB Time Capsuele 4th Gen. and it has been working since I got it, with only a few problems that were quickly resolved. However, it recently stopped allowing internet access to wireless devices. My home computer is connected on airport and actually does have internet access. However, my iPhone and MacBook, although they are recognizing the network and trying to connect, are being denied internet access. I have restarted everything multiple time, changed wireless details (network name and password) and nothing has worked. Anyone know how to fix this?

Start with a full factory reset and redo the setup again.. the full factory is important.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
No luck then it is faulty.. but it is gen3 or earlier.. all Gen4 TC were available with 2 or 3TB drives.. there is no 1TB Gen4. That makes it Gen3 and over 3 years old.

Raid problem with 845 PE and 2 SATA drive

have a big problem, I have bought an mainboard MSI 845PE MAX 3 SR, and I have installed 2 Hard drive Maxtor SATA 80GB in Combination Raid 0. When I install the operating system, Windows XP professional, after I have pushed F6 and insert the floppy, the installation continues but after 3 minute when the system install the FAST TRAK driver, I have a message " The driver is not certified for windows XP " if I click on OK or NO, the system stopped ...
please help me fast
ths
sorry for my bad english

Solved, it turned out to be a setting in BIOS that I overlooked, drive is now in use.

A215-S4747 Unable to Locate and Install PCI Device Driver

This is a Toshiba Satellite A215-S4747 32-bit AMD processor running Windows Vista Home Premium.
I have repeatedly tried to locate the PCI driver by using the discs that accompanied the PC, locating the correct driver on Toshiba Support, and though the device manufacturer is "unknown". I have attempted to write and get a response from the chipset manufacturer - but they claim their is no way for them to know and to contact Toshiba.
So, how do you solve this problem? (PC troubleshooting responses):
PCI Device - failed
OHCI Compliant IEEE 1394 Host Controller - failed
Went to locate: C:\DRVSTEMP - does not exist.
My devices:
Satellite A215-S4747 32-bit AMD processor, Vista Home Premium
Satellite P72-A7200 Intel Core I7 4700MQ CPU @ 2.4GHz, Windows 8.1

Satellite A215-S4747 Specifications
Satellite A215-S4747 Support Page
Let's try this driver and see if resolves the problem. Download this file, double click to install, reboot after installation and test:
TI Card Reader Driver
If this doesn't work, click on 'Start' -> type in: system info -> click on 'System Information' -> in the left-hand pane click on 'Components' -> in the left-hand pane click on 'Problem Devices' -> in the right-hand pane, under the 'PNP Device ID' column, give us the 4 digit VEN number, and the 4 digit DEV number. Like in the below example: VEN_8086 and DEV_4232.
Let us know what happens or give us the above numbers.
Mike

Problem With PSE-2 and New 1.5 TB Drive

Hi all. First of all, I've been using my registered PSE-2 for several years with no problem. AMD Athalon 7750 dual core at 2.7 Ghz, 2.0 G Memory. WD 1.5 TB primary and WD 500 GB secondary drive.Win XP SP3. I recently had a drive fail and installed a new freshly formatted WD 1.5 TB as my boot drive. Fresh install of WinXP and updates. Now when I install Elements, it appears to install fine. The problem comes when I attempt to start it the first time I get "Could not initialize Photoshop Elements because the scratch discs are full". Then Elements closes, thus not allowing me to do anything with the internal configuration of the program. I have tried unistalling and installing to the 500 GB drive, but still get the same error. I have increased my page file memory Does anyone know of a problem with installing Elements on a large drive or can anyone offer a possible solution to what I am seeing? Thanks in advance for suggestions...
JohnR.

I think Barbara meant photoshop 7, which was out a little before pse2.
If you hold down the Alt+Ctrl keys just after you start pse2, a dialog
should appear allowing you to choose the scratch disk (keep holding
the keys until the dialog appears)
If you have a recovery partition on your hard drive, try choosing this for
the scratch disk and then exit pse2. Then restart pse2 and from
Preferences>Plug-ins and Scratch Disks choose your regular hard drive for the scratch disk.
Newer versions of pse, at least newer than 3 or 4 don't seem to have this problem.
MTSTUNER

Problems with Ethernet controller and PCI device driver on Satellite L30-10X

Similar Messages

Maybe you are looking for