Problems with Fingerprint Reader on Touchsmart TX2-1274NR Notebook and Windows 7 Ultimate (64-bit)

I have just upgraded my tx2-1274nr to windows 7 ultimate (64-bit) [my university released the upgrade a week early] and I followed the directions provided by technical support and downloaded/installed all the updated drivers and software. Everything works great (actually better than great) except for two problems.
The fingerprint reader does not work. It shows up in the device manager, but when I try to register a fingerprint, Windows says no reader found.
This problem is not really effecting the performance, but it states on the device stage that I am missing a driver for the keyboard filters? I am not sure if this is important.
Any assistance would be greatly appreciated. I am really loving the new system, especially the multi-touch (installed the drivers from N-trig)!!
Thanks

Hi,
dclane wrote:
The fingerprint reader does not work. It shows up in the device manager, but when I try to register a fingerprint, Windows says no reader found.
Check this and this thread. You need Authentec TrueSuite.
dclane wrote:This problem is not really effecting the performance, but it states on the device stage that I am missing a driver for the keyboard filters? I am not sure if this is important.
If You have any version of Quick Lunch Buttos installed uninstall them and install this here which is provided by HP for Win7.
Message Edited by Daniel_Potyrala on 10-16-2009 12:35 AM
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

Similar Messages

Problem with Win 7 x64, WWAN or WiFi card and Windows XP Mode

I have a T500 with switchable graphics (2056-4RU) with a clean install of Windows 7 Pro x64 with the AT&T WWAN card.
With all the Win7 RTM drivers and Access Connections for Win7, I had a problem that the WWAN card (Ericson F3507g, purchased from Lenovo and working flawlessly under Vista 32-bit) would not initialize. Support told me to uninstall the Win 7 versions of the Power Manager Drivers, WWAN card driver and Access Connections and replace them with the Vista counterparts, which restored the functionality of my WWAN card. Based on the speed with which the support tech came up with the suggested fix, I suspect I am not the only one with the disappearing WWAN card problem.
Now I have found that starting the Windows XP Mode virtual machine kills the WiFi functionality (Intel WiFi Link 5100 AGN) until I disable and re-enable the WiFi adapter in Device Manager and then restart the system. (I have not problems with XP Mode and with the Win7 drivers / Access Connections opening Windows XP Mode did not cause the problem with the WiFi.) Opening Windows XP Mode causes no problem with the wired network adapter on my system).
Thus it appears that I can have functionality of the WWAN and WiFi adapters with XP Mode using the Released Win 7 versions and functionality of Windows XP Mode together OR I can have WWAN but not WiFi functionality with XP Mode using the Vista drivers that support suggested. However, it seems that I cannot have WWAN, WiFi and XP Mode concurrently.
I reproduced the above XP mode / WWAN problem / WiFi problems on a T500 with Win7 x64 owned by another family member.
Does anyone (particularly anyone from Lenovo) have fix for this?
Thanks.

for the sim card, try this:
http://jack.ukleja.com/update-ericsson-f3507g-mobile-broadband-on-windows-7-with-lenovo-thinkpad/com...
I have another operator and I finally gave up. apparently it's also no that easy to install the SIM card, if the plastic thing that helps to remove the SIM card is not the right position, it will overlap the SIM Card chip.
can't help for the WIFI. I had the problems too with access connection and decided to remove it. I use Seven's network manager, which does an equally good job.
Since I have the switch to turn off the wireless, I don't really need access connection anyway.
Finally, something that I learns while struggling with the bluetooth driver: the order in which power manager, access connection and the different drivers are installed DOES affect their effectiveness. I forgot the details but I remember 2 things:
always read the TXT file that is available on the driver page on the lenovo web site and install power manager and access connection last.
Good luck

Very big problem with professional Color Managed Display in PS CC and CS6 win7 64 bits

How to reproduce this problem:
- Photoshop CS6/CC
- Win 7 Ultimate 64 bits English with all the updates.
- ATI 7870 / HD 550 and early graphics cards.
- Dell U3014, CINTIQ 21UX (in the 7870), 2 samsung 2232 in the 5500 (all on, or one at the time)
- Spyder 3/4 Elite, Eyeone Display 2, DispCal (argyll), ColorEyes 1.60
After the calibration and profile process with everyone of this Display profling tools (lets supose that is all right), open a image with more saturated colors (with Adobe 1998 RGB color space) in CS6 or CC, and hit the "F" key to toggle screens.
You will see that the saturated colors will change (will become even more saturated) in the nest two screen modes, and color come back to the "normal" if hit F one more time.
Seems like the photoshop get rid of calibration luts in the 2 F screens modes and come back to normal when the image are in the initial screen mode.
ps: the loaders startups of each display calibration, was choosed one of the time when I restart the PC ( so, there are no multi loaders trying to put your luts at same time)
- PS CS6 / CC and WINDOWS are totally up to date
- The driver of display cards, are the latest AND the windows certificated
- There are no other software installed on the PC that try to handle the display card or even diferents CMS.
- In fact the Windows is a fresh install
- This happen in RGB and CMYK images.
This is very frustating..:(

Dear Lundberg, in fact I'm wrong about this happen in RGB images, only happen in CMYK (whatever CMYK)
If you have an up to date Win 7 64bit, PS CS6 or CC, and calibrate your display with any colorimeter spectrophotometer and their respective softwares. Download an image like this flowers:
http://hdw.eweb4.com/out/663221.html
Before, be sure to set in PS, this color settings attachad :
Open this file, convert to CMYK and hit the F key to toggle between screen modes.
If you have a calibrated display with, let me say, Eyeone and Coloreyes, and the videoLuts loader is on, when you hit the "F" key, the colors on the CMYK image, will become way more saturated/heavy/dense, so Hit the F key until the screen mode is "normal" the color come back to the normal too.
I test this behavior in 8 machines so far, and in all this machines, the change in the colors are very noticiable, to reach a point that I cant be used in color professional works.
I hope that now I could express my self good enough.
Regards.

Problem With Macbook Air 5,1 Graphic Card Driver For Windows 7 - 64 bit

Hello everyone,
I have a macbook air 5,1 , ver 2012-2013
I Installed Windows 7 64bits Ultimate on my macbook, and i downloaded the latest boot camp and i installed it too!
After finish Installing Boot Camp, everything looks fine until it finshes and then i restarted my mac,
Then i found out that my Graphic Card is not working!!,
I Reformated the System 10 times and i tried diffirent versions for example (32 bits) and (home premium) - (Enterprise)
And Still the problem is the same..
It is working perfectly with MAC OSX but on windows it doesn't
I Searched a lot for drivers for intel hd 4000 in intel's website and i downloaded it, but the system is failing when i tried to install a driver from out side boot camp
so i reformat it!,
and now i am working on it without graphic card
Please help!!? any suggestion i would be thankfull <3

Thanks for sharing your tip RatioCynic! That's what this forum is all about!
Happy printing!
Thanks!
Tara
**Although I am an HP employee, I am speaking for myself and not for HP.

HT6114 Is anyone else having problems with connecting to projectors on the OS X and windows partitions after this update?

I am using the thunderbolt port with an adapter for hdmi connecting to a 42" RCA tv from my mid 2012 MacBook Pro 15". I have confirmed that the adapter and the hdmi cable are perfectly fine. I can only connect to a projector on the OS X 10.92 if I keep the displays separate. As soon as I try to use the mirror feature I lose the visual feed. Sound will still go through however.
On my Windows 7 partition the OS can't even detect it is connected to an external display.

Hi there Chinsteig,
You may find the troubleshooting steps in the article below helpful.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
-Griff W.

Problem with Radio Button using JDeveloper 10.1.2 and Windows 2008

When adding Radio Buttons ("Yes and "No") to a swing application and putting them under a button group. Selecting "Yes" the "No" choice diappears

JDev 10.1.2 is quite old, and was never certified for Windows 2008.
No need to post multiple threads - same question as {thread:id=2271522}

IS IT EVEN POSSIBLE TO UPGRADE TOUCHSMART TX2 1274nr TO WINDOWS 7??? Many issues!

Please...any expert have advice on upgrading the Touchsmart TX2-1274nr model from Vista Home Premium to Windows 7 Home Premium using the HP upgrade kit?
I have had several HP help chats since I bought this touchsmart model, and I've only had it for a little over a week and a half. And, it seems the HPOP chat does not allow me to type my sentences out fully...always cuts me off and chops up my sentences. Plus, it seems the agents that "help me" never seem to understand ANYTHING I am asking. This is quite frustrating, irritating and perplexing.
I tried for the first time to upgrade yesterday, and I did not understand the compatibility report. First, it says to update the "KEYBOARD FILTER" prior to upgrade. I searched the computer and nothing comed up, so I have no idea WHAT EXACTLY this is so I can update the driver. Secondly, it recommends uninstalling 11 programs...6 of which are games (which is fine). However, it recommends uninstalling the ATI INSTALLER MANAGER and ATI CONTROL CENTER. This is another VERY CONFUSING and VAGUE recommendation. This is because only the ATI INSTALLER MANAGER is listed in Programs & Features list. When you try to uninstall, it becomes confusing as to does one remove ALL ATI COMPONENTS...and, if not, how do you removed just the CCC and the INSTALLER MANAGER. I managed to get the CCC uninstalled, by performing and "custom" uninstal of the ATI INSTALLER MANAGER in the Prgrams & Features list, but the INSTALLER MANAGER still remains on the computer.
These problems proved for me confusing. So, I go yet again to HP Help chat and the "tech" was NOT HELPFUL. A little sarcastic & vague and just kept saying follow the onscreen instructions. The instructions have me confused, which is why I was asking so WINDOWS 7 INSTALLED CORRECTLY.
So, I went to another forum and asked for help. I was advised that the Keyboard Filter most likely meant it was referencting the N-Trig DuoSense Digitizer, and I was provided the link to the manufacturer's site to download the Windows 7 compatible drivers. HOWEVER, I could not find out why the compatibility report kept telling me to update the "Keyboard Filter" prior to upgrading.
So, I ended up removing all on the compatibility report suggested removals prior to upgrading EXCEPT the KEYBOARD FILTER DRIVER UPDATE & the ATI INSTALLER MANAGER.
I performed the full UPGRADE anyway.
Sure enough, when all was said and done, after the "UPGRADE" it seemed my system was running noticably SLOWER THAN when it had Vista. Secondly, I LOST MY TOUCHSCREEN ability. So, I went back to the link the 3rd party forum person recommended for the N-Trip DuoSense Digitizer Windows 7 drivers...and the touchscreen function returned. However, I KEPT LOSING MY INTERNET CONNECTION. Well, my wifi apeared to show a full wireless connection to our home network, but I would open up internet explorer and it would load my home page. I was able to maybe retain my internet explorer connection for a miunute or 2, and then no matter what website I enetered or link I clicked...NOTHING. It would just keep indicating it was loading but minutes would pass and nothing would happen. Plus, the windows system in general seem to be running slower.
So, I am highly irritated & upset over this. And all my searching and researching on HP site and others seem to not giver SPECIFIC AND CLEAR ANSWERS to any of these issues. WHY????? Am I the only one to have ALL THESE ISSUES? This morning, I ended up performing a F11 Windows recovery back to Vista Home Premium. What should I do?
Please, if anyone has had similar problems, sound off. Moreover...PLEASE if you have updated your Touchsmart TX2-1274nr SUCCESSFULLY....PLEASE...PLEASE...ADVISE me as to how I may accomplish the same!
I thank any advice/suggestions any of you may have in advance. Kindly, Jimmyb30ohio

I have the TX2 1012NR and its can upgrade just fine! Here is a few recommendations "only if u have the HP Upgrade program disks"
If you have them you can install a clean copy and delete everything... Do not use the use me first disk included because it prompts you to install an older BIOS.... Just use the windows 7 upgrade disk and start the process. The clean install clears your entire drive but does not void your warranty! When you use the use me first disk after the install it actually loads everything else needed to get you up in running. The touchscreen driver and the HP Mediasmart programs will have to be downloaded from the HP support site. Once again its recommended that if there were any programs installed delete them do not try to update them! This causes issues and countless errors. Specifically with touchscreen drivers etc uninstall them before installing the ones from HP support. I found this was not the easy way to do it but the best way... I also recommend that when doing any sort of BIOS update that you remove your Battery and leave it connected to a power cord only! Last but not least if you really mess up and its under warranty... Send it to HP they will set it back up to factory defaults under Windows Vista with the more up to date BIOS installed. I hope my information helps! Sure you might loose some programs but in the end your computer runs faster and smoother because all the programs installed are made for Windows 7.... Also they did release the Touch Pack for download from the Microsoft website here is a link telling more about the features and benefits and how to get it as it is a totally free download...
http://windowsteamblog.com/windows/b/windows7/archive/2009/05/27/introducing-the-microsoft-touch-pac...
Microsoft Link for download:
http://www.microsoft.com/downloads/details.aspx?FamilyID=b152fadd-82e4-4ddb-a46a-aebe49944428&displa...

Problem with fingerprint setting

Hey, i bought an iphone 5s yesterday. I set up the fingerprint yesterday and it worked fine. But after that i faced some problem with the system so i reset the wholephone and edit and deleted my original fingerprint. but after that, my phone cant reenter the fingerprint. it can't read any fingerprint and the name is changed to touch id. what should i do with it?

Hello annteoeena,
Congratulations on your iPhone 5s, and thank you for the details of the issue you are experiencing when using Touch ID. I recommend following the steps below for an issue like the one you described:
Troubleshooting Touch ID
Verify that you are using the latest version of iOS.
Ensure that your fingers and the Home button are clean and dry.*
Note: Cover the Home button completely. Don't tap too quickly, don't press down hard, and don't move your finger while Touch ID is scanning.
Tap Settings > General > Passcode & Fingerprint > Fingerprints and verify:
Passcode Unlock or iTunes & App Store is enabled.
One or more fingerprints have been enrolled.
If one finger isn't working, tap Edit in Settings > General > Passcode & Fingerprint > Fingerprints > Edit to delete and then reenroll the finger.
If that finger still isn't working, try enrolling a different finger.
If you are unable to enroll any of your fingers, take your iPhone 5s to an Apple Retail Store, Apple Authorized Service Provider, or contact AppleCare for further assistance.
Find the full article here:
iPhone 5s: Using Touch ID
http://support.apple.com/kb/HT5883
Thank you for using Apple Support Communities.
Best,
Sheila M.

Problem with fingerprint on HP Pro x2 612 g1

hi
i'm having problem with fingerprint on my HP Pro x2 612 g1.. i've installed all of the drivers which i have downloaded using your site and i can see fingerprint option but there is no add button under it.. i'm using windows 8.1 pro 64bit
need your help..
thanks

Here are the direct links to the fingerprint drivers:
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=7268930&swItemId=ob_138590_1&swEnvOid=415...
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=7268930&swItemId=ob_134806_1&swEnvOid=415...
Let me know if that helps.
-Chris
I work for HP.
Support Forums are now on your mobile phone: http://m.hp.com/supportforum

Problem with Adobe Reader not being able to run with Maverick 10.9.2?

problem with Adobe Reader not being able to run with Maverick 10.9.2?

Have you updated your version of Adobe Reader?

Problem with Adobe Reader and IE

I'm using Vista Home Premium and IE9 with the latest Reader available. Starting yesterday, I cannot read PDF files on the web. This is a new problem. I tried to download newer versions of IE and the Reader, but both tell me I've got the newest versions I can use.
I have no problem with Firefox. Just IE. I prefer using IE. Can someone guide me -- without using technical language. Many thanks!!

Thanks for your input. I opened the standalone Adobe Reader X, clicked Edit, Preferences, Security, Advanced Preferences. Then clicked each of the 3 tabs on top, but nothing looked like "Protected Mode."
Then I went back and clicked Security (Enhanced) and unchecked Enable Enhanced Security. Tested this change, but I still get the gray screen and messages: "A problem has caused IE to close." "A problem with this website has caused IE to close and re-open the tab." I then went back and re-checked Enable Enhanced Security.
I should mention that I have used this particular website for about 10 years and never had a problem. But I now have the same problem with any online PDF that I try to open using IE.
Can you think of anything else? If not, here's my plan of attack. Please let me know if you think it will work.
1) Copy over all my favorite sites from IE to Firefox. (I've already started doing that.)
2) Uninstall IE and re-install it.
3) If I still have a problem, uninstall Adobe Reader and re-install it.
Do you think this will do the job if all else fails?
Many, many thanks for the time you have put into this.

Problem with adobe reader, commenting

one of our authors is using adobe reader x 11,1, and I send him a pdf (enabled commenting and measuring), but for some reason the commenting-fields does not show on his screen?
should I save the pdf in another way?

What do you mean by "commenting fields" exactly? By “commenting filds” I mean the tools in top of the page – delete, highlight etc. When I send the pdf, I save it as “file - save as - reader extended pdf – enable commenting and measuring”, otherwise the commenting tools normally don’t appear by the author.
Are they existing comments? no, it is the text in his pdf-book he needs to correct
Is he able to access the commenting tools? no
You can try sending a non-enabled version since Reader 11 can add comments to a non-enabled document. will try that J
Fra: George Johnson [email protected]
Sendt: 6. november 2012 16:16
Til: Forlagene Idag & Nordan
Emne: problem with adobe reader, commenting
Re: problem with adobe reader, commenting
created by George Johnson <http://forums.adobe.com/people/George_Johnson> in Creating, Editing & Exporting PDFs - View the full discussion <http://forums.adobe.com/message/4826849#4826849

Continued problems with Adobe Reader 9.3.1

Adobe Reader stops at the half-way mark in the progress block when loading a form to print. Cannot get this fixed. Does anyone out there have a fix for this. Is Adobe even recognizing that there is a problem with this. Error message keeps telling me that there is a problem with Adobe Reader, exit and try again.

I haven't been able to print any .pdf files since I downloaded 9.3.
My message says Internet Explorer has closed it down because of data executable files. I've changed my DEF settings to allow
Adobe Reader but it still doesn't work. I never had any problems before with newer versions.

Having problem with adobe reader

Hi,
I have a problem with adobe reader in my cell phone E71 model recently.I could open any pdf files till yesterday,but now without any reason the adobe reader icon in the office folder does not open.I wanna know what should I do.

Might be some problem with adobe reader. You may Google another pdf app called pdf plus. Install it and see if the problem is solved or not.
Nokia C7

Problems with flash reader, flash reader

problems with flash reader, flash reader

flash reader is an App for iPhone, iPad and iPod. Do you mean Flash Player?
And, what is the problem?

Problems with Fingerprint Reader on Touchsmart TX2-1274NR Notebook and Windows 7 Ultimate (64-bit)

Similar Messages

Maybe you are looking for