Problems with my iLuv radio adapter

i have a iPod touch and i got a iLuv radio adapter but my ipod wont play music through it. it connects to it and charges while connected but the songs wont play. anyone had this problem and know a fix?

Try changeing the wireless channel width on the router to (20MHZ only ).. and standard channel to 1 , 6 or 11 (Oberve the connectivity on each channel for some time)
Check if there is any other interference devices (2.4GHZ)
And the last thing you can try is disabling the firewall on the router
Go to the setup page of the router - Unchecked the box which says Filter Anonymous Internet Requests under the security tab..

Similar Messages

Having problem with appletv iTunes Radio. Music stops, get spinning wheel, never restarts.

Having problem with appletv iTunes Radio. Music stops, get spinning wheel, never restarts. If I switch to another station it plays immediately, but it too sometimes stops for the same reason. Wait for 10 minutes for it to restart, then switch stations again. I've tested my download speed when it happens it's fine.

What was the connection speed when you tested
Make sure DNS is set to automatic
Reboot ATV and router
If on wifi try ethernet

Problems with the FM Radio after USB connection

I've been searching around for anyone else having this issue and I though I would ask before I sent my N97 phone in for repair.
Does anyone have or seen a problem with the FM radio loosing all its frequencies after it has been plugged into the USB charger? Everytime my phone is charged, my radio plays nothing by static. The radio stations are still there, but nothing but static can be heard. I have to reboot my phone to get it working. Since I listen to the radio everyday (the reason I got this phone and my n95) I am constantly rebooting this bloody thing.
Also, I have a problem rebooting my phone. Sometimes it just won't enable the buttons after the phone has been locked. The side toggle switch doesn't work, and when I touch the screen it says to unlock it. So I'm forced to remove the battery to reboot it. It doesn't happen all the time, happens about 30% of the time.
Please if anyone can help? I really don't want to send my phone in for repair.

Hello,
Try to remove the n97 battery and keep the "on" button pressed for a few seconds. Then reinsert the battery and turn the phone on. That should get rid of all the accumulated static electricity on the phone. As for your other problem, the only thing I can think of is reinstalling your current firmware and resetting your phone.

Problems with Wireless Router and Adapter

I tried posting this in the wireless adapter forum but nobody responded :-(
I'm using a WRT54G Router btw, and the firmware is v2.02.7, Feb. 27, 2004.
Hi everyone,
I have a Linksys Wireless G Router and several computers that I try to connect with. One of them is a computer running Windows XP and using a Linksys Wireless USB B Adapter (WUSB11). Another is a laptop running Mandriva Linux using a Linksys Instant Wireless Network PC Card (WPC11). Another one is running Windows Vista and using a Linksys Wireless N card. I also have a laptop running Windows XP using a Linksys Wireless-G Notebook Adapter (WPC54G). I also have another PC running Windows XP and uses a Linksys Wireless USB Adapter WUSB54G. Finally, I have two macintosh laptops running OSX and with airport devices installed.
Anyway, I have problems with my internet connection frequently being interrupted and even sometimes I won't have a connection at all for hours. This occurs with my Linux laptop, the PC with the Wireless B Adapter, and the laptop using the Wireless G Notebook Adapter. In addition to this, the macintosh laptops have internet even more infrequently. However, I seem to never have a problem with the Windows Vista desktop or the Windows XP desktop that has the Wireless G adapter. I try repairing the connection and often it does not work. I have also tried resetting the router and the cable modem. I'm not sure what else I can do. I even bought a Wireless N router and had little success with that. We even went as far as moving the wireless router upstairs into our living room, thinking that the signal was somehow suffering from interference or that distance was a factor. Anyway, sorry for the long post but I could really use some help!
Thanks.

Hi… logon to wireless N router’s setup page, open I.E. an in the address bar type 192.168.1.1 it would ask for username and password, put "admin" as a paassword (default password) without any username...linksys setup pops up, click on on wireless tab and and try changing radio band to wide 40MHz, wide channel to 9 and wireless standard channel to 1 or 11, go to advanced wireless settings reduce beacon interval to 50, fragmentation and RTS threshold to 2304, change N Transmission rate to 270 MBps…also try upgrading latest firmware on router, check whether it makes any difference or not and let me know.

Problem with XML SQL JDBC adapter

Hello All.
I have quite strange problem with my PI.
Whole scenario is SOAP -> JDBC, asynchronous. Everything works fine on DEV server. After transporting objects (using CTS) to QA env I'm getting this error:
JDBC Message processing failed, due to Error processing request in sax parser:
No 'action' attribute found in XML document
(attribute "action" missing or wrong XML structure)
But document seems to be correct. I've compared it to DEV server documents - they are identical. What could be wrong??
Document looks like this:
<ns2:BIPMessage xmlns:ns2="http://mynamespace.com/xi/sn"
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<synchSlLok>
 <STATEMENTNAME>
 <SYNCH_SL_LOK ACTION="INSERT">
 <TABLE>SYNCH_SL_LOK</TABLE>
 <ACCESS>
 <ID_TRANS>22050</ID_TRANS>
 <ID_LOK>1234</ID_LOK>
 <ID_CBK>1000050911</ID_CBK>
 <NR_LOK>1234</NR_LOK>
 <OPIS_LOK>12312312312312</OPIS_LOK>
 <TYP>D</TYP>
 <OPERACJA>U</OPERACJA>
 </ACCESS>
 </SYNCH_SL_LOK>
 </STATEMENTNAME>
</synchSlLok>
</ns2:BIPMessage>
TIA
Best Regads
Maciej

Hi,
i was also facing the same error few days back in a JDBC -RFC-JDBC Synchronous scenario. In that scenario, i was using 2 modules in JDBC sender module tab. It was working fine. later i change polling interval and then i started getting same error. it happened coz of sequence of Module got changed somehow.
So please check in Receiver JDBC adapter and SOAP sender adapter CC if anything is changed. If this scenario is working in DEV as it is then it should work after transport.
Else have a look here
Re: attribute "action" missing or wrong XML structure
JDBC - No 'action' attribute found in XML document - error
Regards
Aashish Sinha
Edited by: Aashish Sinha on Mar 15, 2011 10:42 AM

Problem with SP 15 (File-Adapter etc.)

Hallo,
has anybody face to problems with sp 15? It may be a problem with the file-adapter. Whats yours experiences with sp 15?
Thanks in advance,
Frank

Hi Frank,
I am not sure about the issues with SP15, but Michal's Frequently Asked Questions blog talks about what to do if your adapters are not shown after an upgrade to some SP. Just check it out,
/people/michal.krawczyk2/blog/2005/06/28/xipi-faq-frequently-asked-questions
Question 3 under Adapters,
I can't see my adapters in the adater monitoring after the import of a new SP
a) try reimporting "SAP Basis software component"
b) take a look at the XI installation guide on how to do it: "Importing the XI Content for Software Component Version SAP Basis 6.40"
Regards,
Bhavesh

Problem with stream from radio

Sorry for my english, I wanted to posted on my local forum but it have problem with server and doesn`t work
So on windows all channel this radio work good but on arch the main channel can`t running
I suppose it`s depend of my iptables setting, I did all setting by this how to http://wiki.archlinux.org/index.php/Sim … wall_HOWTO
from part " Setting up a single machine"
This is adress radio channel with I have problem http://87.118.100.10:7000, in audacious I have only info "prebuffering" and nothing else
vic can run this channel but stream is very dashed. It`s very strange because on windows all work good
I tryed cut iptables in rc.conf in sector daemon and reboot but it was similar
I sent this adress to my friend who use too arch and he had got the same problem
Do you have idea why i have this problem
Second time I`m sorry for my english but please help me
Last edited by yellowfox (2007-02-16 12:21:01)

Your english is much better than my american, so maybe we can communicate somehow.
I don't use iptables since I have a router handling that for me.
Trying http://87.118.100.10:7000/ with xmms, vlc, amarok and mplayer resulted in not much. VLC did give very choppy playback, while xmms got in a buffering/prebuffering loop.
Using amarok or mplayer to open http://87.118.100.10:7000/listen.pls resulted in good music. Wish I could understand the lyrics but I could listen to it.
Opening http://87.118.100.10:7000 in firefox leads to a Shoutcast Admin control panel where the link Listen results in a playlist file.
It also tells me that they are stream aac sound, so, maybe the right plugin or a recompile after installing faad will make your chosen program work.
Good luck and have fun

I am having problems with Apple tv radio. It cuts out after a few minutes this appears to have happened after update to IOS 8

I Am having problems with the radio on the Apple TV cutting out after a few minutes. This has started to happen after software update to Ios8. Has anyone else had this problem and are Apple looking into fixing it?

I am having the same problem also Thought it was my network and reset everything including Apple TV but still the problem is there . I assume now it is down to iOS 8 prior to that was perfect

Problems with NI-488 cPCI adapter under QNX.

Hi Michael,
The problems that I am having with the NI 488 cPCI adapter are random, so
it is
very difficult to nail down where the problem lies. Sometimes the adapter
fails
the initialization sequence in the nitn_presence_check routine at various
points in the 4 tests that the driver performs. Other times, if the adapter
initialization passes, the driver will loop in the nitn_wrtPIO with the
message
"waiting, isr3=0x4c" or "waiting, isr3=0x00". I have added a loop count to
the
routine so that it exits after 100 loops, but it still affects the driver
performance. I have had a similar problem with the nitn_wrt1byte routine.
I have been told that the driver works under Windows and Linux, but it
doesn't
work under QNX, and I have no idea why not, as I don't have any chip-level
documentation on the adapter. I will appreciate any help that you can give.
Thanks, Hugh.

Hi bearhug,
This post was a little confusing. Was it started in another thread and moved over to a new one accidentally? Since it appears that you have had some previous correspondence, I looked into the type of issue you are experiencing and it looks like Michael, one of our Applications Engineers, has an in-work service request related to it. If that is your service request, I would encourage you to contact him directly by calling 1-866-275-6964 and entering the service request number there. Please let me know if there has been some miscommunication.
Best regards,
Matt J
Matt J.

Problem with Variable Substitution Receiver Adapter

Hi,
I need to use a dynamic filename so I'm using the variable substitution in my receiver adapter. BUT, the filename can't appear in the file. So i used this blog in reference --> Solution to the problem encountered using Variable Substitution with XI-SP12
The PROBLEM is I still get and extra blank line in the file. How can I eliminate this extra line?
Thanks in advance.
Using XI 7.0

Hi Gaurav,
Data Type:
Lines
Line
Config
FileName
XML - example:
<?xml version="1.0" encoding="utf-8"?>
<nr1:MT_TP_TipoCambio_Detalle_ECC_Req xmlns:nr1="urn:erplatam/tipocambio:tp:ecc">
<Lines>
<Line>USDSOL0000000000003.10000013-09-200813-09-2008V</Line>
</Lines>
<Lines>
<Line>USDSOL0000000000002.50000014-09-200814-09-2008V</Line>
</Lines>
<Config>
<FileName>SIGMA_TCSAP_F081031.DAT.TXT</FileName>
</Config>
</nr1:MT_TP_TipoCambio_Detalle_ECC_Req>
Output - File, has 3 lines should have only 2:
USDSOL0000000000003.10000013-09-200813-09-2008V
USDSOL0000000000002.50000014-09-200814-09-2008V
FCC parameters:
RecordSet Structure: Lines,Config
Lines.fieldSeparator 'nl'
Lines.endSeparator 'nl'
Config.fieldSeparator 'nl'
Config.endSeparator 'nl'
Thanks in advance!

Problem with audio and vga adapter in presentations

this is an odd problem. I potted a presentation that contained a qt movie. The video plays with sound just fine via the vga adapter until you plug in an external speaker system or earphone. the sound stops.
if you play a video outside keynote or play the video with out the video vga adapter or just unplug from the audio jack it works fine. am I missing something or is this a bug. For the life of me I can not figure out what the VGA in keynote has to do with audio.
John

Dr. John, this might be a little simple of an answer, but is the video jack pushed all the way in?
I had the same issue with my ipad playing a movie over a sound system and projecting it also, and discovered that the Apple issue iPad cover comes very close to interfering with the audio output jack, and that my plug into that jack wasn't all of the way in.
After that it's worked fine.

Problem With Receiver Communication (File Adapter)

Hi,
My SAP XI Version is 3.0 with Service Pack 7,I have a strange problem,
I have a flat file coming from Unix system,I need to convert this into XML and put a copy in the Archive mode and send the XML file,getting it converted into flat file format send it to the receiver.Here I have to do the content Conversion,So,I have done content conversion while configuring Sender and Receiver Communication Channel.
I am using NFS as Transport Proctocol.So, everthing was fine when i run the scenario,after activating.The Sender communication Channel is Archiving the files.But I am unable to see any file with receiver communication channel.
So,for this I have checked up with Adapter monitoring in Runtime Workbench. In my File Adapter My Sender as well as Receiver Communication Channels are in Green.They are mentioning that Sender Communction is sucessful and
RECEIVER COMMUNICATION IS Sucessful but no messages processed.
Can any one suggest what to do now.Everything is fine with Content conversion and Unix System.But my receiver is not receiving any messages.
Should any OSS notice or patch work needs to be applied.
Thank You,
KishoreJ.

Hi Kishore,
I Guess you should first see if the file is being picked......for that do the following.
While configuring your Sender File Adapter, let the mode be DELETE. This way, we will know if the file is being picked by the File adapter. The file will be deleted and you can be sure that it has been picked up.
Next, look into the RWB--> FILE ADAPTER and see the log of the file adapter
and also, you can see the flow of your message in the integration engine in SXMB_MONI.
Ans still if your message is not showing up in SXMB_MONI, please do as explained below.
Increase logging and trace level in:
SXMB_ADM -> Integration Engine Configuration -> Specific Configuration
Also create entries as follows in it:
LOGGING = 1
LOGGING_SYNC = 1
TRACE_LEVEL = 3
TRACE_LEVEL_PROPAGATION = 1
Also refer XI: I cannot see some of my messages in the SXMB_MONI
Regards,
Abhy

Problem With Seeing Message in Adapter Engine

Hello Everyone,
We are facing a strange problem while running an Integration Process, BPM in PI. In the process, we are trying to read a .CSV File and convert it into a .XML File via FCC. The .CSV file is placed in the XI box itself, under a certain directory. We have configured the process such that whenever the .CSV file is read, its attributes are set to 'read only'. After configuring the process, the required XML file did not show up. So we checked that whether the .CSV file was read and it showed up attributes of 'read only'.We cross checked
 -First by going to SXMB_MONI; here it said 'No messages available for selection'
 -Then by examining the 'channel monitoring' in AE; where we found both the sender and receiver channel are showing green. The sender channel first shows up that 'Processing started' and then 'Processing Completed Successfully'. The receiver channel does not show up any messages.
 -we checked for the XML messages that are in the Adapter in IDX5; it shows 'no messages selected'.
 -We anticipated that it may be a cache problem and cleared all the caches; but when we tried to clear the Adapter Framework Cache, it popped up an authorization error and the problem persisted.
We are using NW2004s with SP6 at the ABAP and BASIS stack and SP 9 at the Java Stack. Also, all the required connections made in SM59 are in order.
Now, What can be the problem? Is it the difference in SP level that is causing the problem? Or is it something else? What have we missed? Guys, please help us solve this problem.
Need Help. Pleae Reply. Points will be awarded.
Thanking in anticipation.
Amitabha

Hi Shabarish,
1.Document name is indeed the name of message type in our case.
2. We did not use delete mode; but once the file was read- we manually changed its attributes from 'RA' to 'A'..and it became 'RA' again after 2 seconds; which is our polling interval.
3. And we have discovered that the file is being read properly..because we can see the XML payload of it and it contains the correct data.But still it does neither show up in SXMB_MONI..nor in IDX5.
Can you please tell us what are the necessary roles for the User PIAFUSER? We suspect that somewhere's an authorization error we are getting; because the AF cache refresh attempt shows "Forbidden" and we are getting an error in Tcode SXI_SHOW_MESSAGE as:
AE_DETAILS_GET_ERROR: no_adapter_engine_found: Unable to find Adapter Engine:; Stack trace shows:Error while reading access data (URL, user, password) for the Adapter Engine

Audio problem with firewire to thunderbolt adapter

I am running four channels of audio from a Yamaha Motif synthesizer into a new iMac using the firewire to thunderbolt adapter and recording to Logic. I get very loud distortion. I unplug the same cord and remove the adapter and run the same audio into my 2011 MacBook Pro and record the audio with no distortion. I can run MIDI into the iMac using the adapter with no problem. What gives?

The iMac has three USB and three Thunderbolt. The Yamaha has Firewire out which carries 16 channels of audio. It works great with my MacBook Pro, but the Thunderbolt Converter seems to mess it up. It's fru
strating having bought a brand new iMac and not being able to use it to record. Now when I try to record a single channel of piano, Logic starts blinking on and off, alternating with whatever window is behind it. This is doubly frustrating.

Problem with Sender JMS J2EE adapter...

I have configured the sender JMS J2EE adpater. I am getting this error at Adapter monitoring:
Sender channel. Details: Last Exception during send at Fri May 25 09:44:18 CEST 2007: Error converting Message: 'java.lang.Exception: ERROR consistency check in recordset structure validation (line no. 1: missing structure(s) in last recordset'.
I am using recordset structure as Header,1,Item,99999. and also i am ignoring the recordsetName...i tried confiuring the File adapter using same parameters as in JMS adapter it is not giving any error at Adapter Monitoring.
Also i configured File adapter by putting in their the parameters of J2EE JMS adapter in Module tab, it too worked...
so What is exactly this error, if anyone can please tell me...

Hi,
Check some links for FCC
Introduction to simple(File-XI-File)scenario and complete walk through for starters(Part1)
Introduction to simple (File-XI-File)scenario and complete walk through for starters(Part2)
File Receiver with Content Conversion
Content Conversion (Pattern/Random content in input file)
NAB the TAB (File Adapter)
Introduction to simple(File-XI-File)scenario and complete walk through for starters(Part1)
Introduction to simple (File-XI-File)scenario and complete walk through for starters(Part2)
How to send a flat file with various field lengths and variable substructures to XI 3.0
Content Conversion (Pattern/Random content in input file)
NAB the TAB (File Adapter)
File Content Conversion for Unequal Number of Columns
Content Conversion ( The Key Field Problem )
The specified item was not found.
File Receiver with Content Conversion
http://help.sap.com/saphelp_nw04/helpdata/en/d2/bab440c97f3716e10000000a155106/content.htm
Regards,
Phani

Problems with my iLuv radio adapter

Similar Messages

Maybe you are looking for