Problems with N91(GSM) multimedia/music key

the multimedia key pressing which can be entered directly to the NOW PLAYING option of the music player is not working properly in my set.whenever i press that key a message is shown on the screen..."ITEM NO LONGER AVAILABLE.RESTORING DEFAULT MULTIMEDIA KEY SETTINGS"...i can't find the solution of the problem.can anyone help me???

well it is refresing for the past 10 minutes, for 100+ mb of data does it suppose to take this long? still going on though ...
Currently owns : Nokia N91 / Sony Ericsson P910i / Imate Jasjam

Similar Messages

Ovi maps problems with Nokia 5800 xpress music

Since Ovi updated the maps I've had trouble using it. I have version 40 firmware which was installed by Vodafone when my device expired. Despite the update, Ovi maps just crashes the phone when I try to use it. The screen goes blank and I get all coloured lines flashing down one side and the phone reluctantly restarts. Any advice please?

I am having exactly the same problem with my 5800 xpress music having updated to version 40.0.005.235.10 and installed the new version of OVI maps and the software Own Voice.
I have also tried reinstalling the sotware, restoring my phone to factory settings and resetting my phone by pressing the green, red and camera button whilst powering up. The problem persists. I will be making a call and within a few seconds of the call being connected the phone switches off and back on again. I also get the the coloured lines flasing on the screen.
Please Nokia Support, help us out.

Problem with childs nodes and automatic key mapping in a Data Object

Hi experts!
I'm doing the service order tutorial from the mobile help at [this link|http://help.sap.com/saphelp_nwmobile71/helpdata/en/21/9b5b924c3b434fba4767731794b029/frameset.htm] and I have a problem...
In the topic "Modeling the Equipment Data Object", says you have to mark the "Automatic Key Mapping" checkbox. So when I had to create a third child node ( the location node ) the system raised an exception with the message "Deselect automatic key mapping flag for more than two-level nodes". I'm trying deselecting the flag and creating the location node, but when I want mark again the automatic key mapping flag, this is disabled.
What can I do to solve this and create the three child nodes with the flag marked? It's a configuration thing?
Any help it's very welcome. Thanks in advance.
Best regards,
Simon.

The thing is: Its not allowed to use automatic keymapping if you have more than two levels. This is why the message showed up, and this is why its been disabled.
What automatic keymapping does: Figures out automatically which child node belongs to which parent (by guessing from the field name and type, which fields in the child correspond to which key fields of the parent).
On three levels, this becomes more complicated => Its disabled.
How to do keymapping yourself instead of having the DOE do it automatically: Do 'Explicit keymapping' from each child to its parent. Explicit keymapping is done by clicking on the corresponding menu button in the child node. Here you need to associate child node fields (they need not be key fields of the child, but they are allowed to be that as well) to each of its parent nodes key fields (so that each child can be associated to its parent).
Cheers

Having a problem with creating/using a primary key on a view

I have a problem with a primary key on a view
I created the view and primary key as follows:
CREATE OR REPLACE FORCE VIEW "MDD"."ROCK_LU" ("DESCRIPTION",
UNIQUE ("DESCRIPTION") RELY DISABLE,
CONSTRAINT "ROCK_LU_PK" PRIMARY KEY ("DESCRIPTION") RELY DISABLE) AS
SELECT DESCRIPTION
FROM MRMC_LU
WHERE ROCK = 'T';
The view with the primary key appears to have been created as there were no error messages. (The above was from the sql tab in sql developer.)
When I try to create the foreign key on my mdd_hr table - I get an error
/* hr_name - foreign key */
ALTER TABLE mdd_hr add CONSTRAINT hr_name_fk FOREIGN KEY (hr_name) REFERENCES rock_lu(description);
Error report:
SQL Error: ORA-02270: no matching unique or primary key for this column-list.
When I lookup the index in sql developer, rock_lu_pk is not there.
All my other foreign keys work - but I don't understand what I am doing wrong with this one. Please help.
glenn
Background - as to why I want to use a view as a lookup table.
The MRMC_LU table that the view is created from is structured like:
DESCRIPTION - MINERAL - ROCK - MODIFIER - COMMODITY
ANHYDRITE - T - T - T
APLITE - T - - T
GRAPHITE - T - - - T
GREYWACKE - - T
DESCRIPTION is a list of all names of minerals, rocks, modifiers and commodities. T is entered in each valid field. Often a description name is used for both a mineral and a rock or a mineral and a commodity or any other combination. Because this database is just starting up, it was more efficient to create one table that could be updated (and thereby automatically update the MINERAL_LU, ROCK_LU, MODIFIER_LY, COMMODITY_LU views) rather than create and maintain four separate but similar tables. A primary key cannot be generated for the MRMC_LU table as there are nulls in each column
except DESCRIPTION.
Perhaps there is a smarter way to do this?

http://download-uk.oracle.com/docs/cd/B10501_01/server.920/a96540/statements_85a.htm#2065512
You can specify constraints on views and object views. You define the constraint at the view level using the out_of_line_constraint clause. You define the constraint as part of column or attribute specification using the inline_constraint clause after the appropriate alias.
Oracle does not enforce view constraints. However, operations on views are subject to the integrity constraints defined on the underlying base tables. This means that you can enforce constraints on views through constraints on base tables.
Restrictions on View Constraints
View constraints are a subset of table constraints and are subject to the following restrictions:
You can specify only unique, primary key, and foreign key constraints on views. However, you can define the view using the WITH CHECK OPTION clause, which is equivalent to specifying a check constraint for the view.
Because view constraints are not enforced directly, you cannot specify INITIALLY DEFERRED or DEFERRABLE.
View constraints are supported only in DISABLE NOVALIDATE mode. You must specify the keywords DISABLE NOVALIDATE when you declare the view constraint, and you cannot specify any other mode.
You cannot specify the using_index_clause, the exceptions_clause clause, or the ON DELETE clause of the references_clause.
You cannot define view constraints on attributes of an object column.
Rgds.

Problem with type conversion and primary key during row fetch

[Note, this error occurs in Oracle XE, APEX 2.1.0.00.39]
I have been having a problem with Automatic Row Fetch:
ORA-01460: unimplemented or unreasonable conversion requested
So in an effort to resolve this, I created a PL/SQL process with the query below and was able to isolate the same error. The problem seems to come from one of the primary keys being a "number" type (APP_ID). The error occurs on the line:
where u.app_id=:P5_APP_ID
I have tried the following variations on this line in an effort to resolve this, but all generate the same error:
1) where to_char(u.app_id) = :P5_APP_ID
2) where u.app_id = to_number(:P5_APP_ID)
3) where to_char(u.app_id) = to_char(:P5_APP_ID)
I've also tried the laternate syntax "&__." and "#__#", but these don't function in the Source field and show up as syntax errors.
Any suggestions are welcome.
begin
for r in (
select app_name, apptype, appcreator, appurl
from application_users u, application_info i
where u.app_id=:P5_APP_ID
and i.app_id=u.app_id
and u.username=:P5_USERNAME)
loop
begin
:P5_APP_NAME := r.app_name;
:P5_APPURL := r.appurl;
exception
when others then
raise_application_error(-20000,'In Loop Failure',true);
end;
end loop;
exception
when others then
raise_application_error(-20000,'Out of Loop Failure',true);
end;
Thanks in advance,
Barney

I found a prior post referencing a similar issue and it was solved by using the "v(__)" syntax. This did resolve my issue, however, I have a quick follow-on which I'm hoping someone can answer quickly...
Since the "v(__)" syntax won't work for the Automatic Row Fetch (at least to the best of my knowledge), I have to do a manual process. However, the manual query as shown above doesn't actually populate any of the form values through the bind variables. They all remain at their cached values from prior data entry on the form.
Is using the bind variables for assignment incorrect, or is there something that must be done to get the updates to show up in the form (ordering of processes, etc.).
My manual process is running in the Load: Before Header state so I would have expected it to update all of the fields.
Thanks in advance,
Barney

Problems with ViaVoice under Leopard, especially key mapping problems

ViaVoice's behavior has changed considerably under Leopard. First I will discuss the key mapping problem, since I'm eagerly looking for an answer to this problem. At the end of this post, I will voice some of the other problems I've experienced for those who may be interested. The key mapping problem may be specific to the fact that I use a foreign keyboard with a US version of ViaVoice.
INTRO:
I have used ViaVoice on my Mac for years, more or less without problems (ViaVoice's bugginess is notorious).
Those who know ViaVoice will know that one has two general options for dictation. One can dictate into ViaVoice's so-called SpeakPad, which allows special formatting, editing and dictation error correction within the dictated text, or one can dictate into "external" software such as Microsoft Word, in which case ViaVoice just sends a string of characters to that software. SpeakPad appears to make strong use of the operating system's built-in functionality for character formatting, document formatting, etc.
*MY PROBLEM*
I have a German keyboard on my PowerBook, yet dictate in US English. When I dictated into SpeakPad under Tiger, all characters appeared correctly. However, when I dictated into Microsoft Word using Tiger, I had to switch the keyboard mapping from German to US to get all characters (that means including the characters that are located at different positions on a German keyboard than they are on a US keyboard such as y, z, apostrophes and parentheses) to appear correctly.
Under Leopard, things have changed. Now it doesn't matter whether I dictate into SpeakPad or Word; the results are the same and many characters do not appear correctly.
If set to a German keyboard, y and z appear as expected. To name a few irregularities:
"(" appears as ")"
")" appears as "="
apostrophes appear as "#" and
";" appears as ","
If set to a US keyboard, y and z are interchanged. "(" and ")" appear as expected. Apostrophes appear as "\" and ";" appears as ","
By comparison, if typed (as opposed to dictated, as in the examples above) "correctly" (i.e. based on the letters printed on the keyboard) on a German keyboard set to imitate a US keyboard:
y and z are interchanged
apostrophes appear as "|"
"(" appears as "*"
")" appears as "(" and
";" appears as the symbol for "less than"
Since I don't have a US keyboard, I can't say how it would behave if set to imitate a German keyboard, i.e. if there's a correlation to the results I get when I dictate.
Since I was previously able to dictate correctly into SpeakPad by setting the keyboard to "German" and into Word by setting the keyboard to "US," I presume that this is a problem in Leopard, not ViaVoice.
*OTHER PROBLEMS WITH VIAVOICE UNDER LEOPARD*
In addition to the aforementioned key mapping problems (that may be specific to those of us with foreign keyboards), ViaVoice appears to have lost considerable functionality in Leopard. I cannot access SpeakPad's Preferences and the correction window. Moreover, the traffic-light like window buttons have disappeared from the VoiceCenter (although they work if you click where they should be). SetupAssistent appears to function.
I've written to Nuance about these problems, but have little hope that they will invest the time in producing a patch since they haven't released any updates since 2003.

Thrums1,
I've never had to "register" ViaVoice after updating the system. I thus suspect you haven't fully followed my above, three-step advice (particularly step 3).
1) Reinstall ViaVoice from CD.
2) Update to the latest version (using the patch downloadable from Nuance's website).
3) Replace the “temp” and “users” folders (in the "ViaVoice" folder at the upper level of your home directory) by a previous copy thereof. When I say previous copy, I mean a copy from when ViaVoice was still working properly, e.g. a copy from when it was running under Tiger.
As I said, I've gotten ViaVoice to survive several system updates by following the above steps. To my knowledge, the last step is critical since it saves you from having to reconfigure ViaVoice under the new operating system (in this case Leopard). I suspect that ViaVoice is crashing on your system because it's trying to start some module of the SetUpAssistant that is incompatible with Leopard (as many are). If you instead use old copies of the "temp" and "users" folders (from the previous system), then ViaVoice doesn't have to go through the initial "registration" process; ViaVoice doesn't need the SetUpAssistant; and all is (more or less) fine.
Good luck!
BTW, to my knowledge, Dictate only runs on Intel Macs. It thus won't run on a G4 iBook, just as it won't run on my PowerBook G4.

Intermittent problem with cross dissolve and chroma key

It seems that in 1 out of 10 videos I produce in Final Cut Pro there is a problem with the cross dissolve effect and chroma key. What happens is that during the cross dissolve, clip A fades out with a green tint and clip B fades in with a green tint.
Today I am working with two videos that I captured using the same work flow on the same day. One project exhibits the tint while the second project does not. If I import the problematic footage into the good project the tint problem follows the footage. In the good footage, the cross dissolve produces a result that does not have a green tint. If I re-capture the "bad" footage the results are the same.
Has anyone else experienced this and does anyone have an idea how to resolve this problem?
Thank you.
Dual G5 Mac OS X (10.4.6)

In my project, both clips are source clips with Chroma, Color Smoothing and Matte Choker applied. A dissolve from non-chroma clip to chroma clip works fine. Only problem is with two chroma clips. In my dissolve, the error appears as red fringing in the area between the two masks.< </div>
You're using creative shorthand that doesn't help. "Chroma clip" means the clip to which you have applied all of these effects? What masks? Where are you getting the masks?
To understand what's going on with all them itty bitty pixels in a stack of interactive effects, do me a favor: render out a short piece, say 10 seconds of each of your chromaclips as separate movies over transparency using the Animation codec. Reimport them and put them over a solid colored Dissolve between them using different types of dissolves. Post back and tell us (me) what's going on.
I still consider this to be a bug -- nesting adds more steps to the workflow than if this bug did not exist. < </div>
It's not a bug. Your pixels are running down a pathway. It's a question of building the correct pathway and having the correct pixel wranglers with the right kinds of cattle prods.
bogiesan

Hi i ve a problem with nokia 3230 multimedia messa...

i am using nokia 3230 phone & having a problem with my phone's mms whenever i open messages and then click on mms nothing opens. i dont know why the phone behaving so, i downloaded mms settings from my networks website but it still not working please help me.

Sounds like a software problem do a hard reset . Turn your phone off now befor u turn your phone back on press and hold the star key ,,,the number 3 key and the green call key ... Now keep all of them held down while u turn the phone on keep them down untill your phone has totaly booted up . Now put all settings in your phone again as a hard reset wipes all data off ur phone .... Now it should qork ..... Good luck

Problems with changes in iOS5 Music app on iPad

With iOS 5, massive changes have been made to the Music app that makes it virtually unusable for listening to podcasts. Weirdly, these changes were not made on the iPhone version, which still works fine.
My problems are these:
1.     Music App no longer shows which episodes of a podcast have been fully played, partially played, or not played.
2.     The 30-second re-play button is gone.
3.     The 1X - 2X - ½X playback speed button is gone.
These items aren't very important for playing music, but they're pretty critical for listening to podcasts. As I said, these features are still on the iPhone version of iOS5. It's like somebody decided that no one listens to podcasts on the iPad so they took them out. If that's true, then it's just me that's screwed.
Am I missing something? Is there a way to bring these features back? I've tried Apple Care and they didn't have a clue. And before someone suggests it, yes, I have submitted a comment to the feedback web page at Apple.
Thanks,
Rolando

I am with you.   4 out of 5 people in the office not longer are able to open email attachments(PDFs, jpgs, Office Docs) after upgrading to iOS 5 on iPhones or iPads. It seems to be from only from emails not from a Mac, iPhone or iPad. If you forward the message to youself from an Apple product, you will be able to open the attachment.
If called Apple support and they were not able to help after an 50 Mins. I'm going to re-install iOS to see if if works.

Problem with the Ipod Touch Music Player

Hi, I recently got an iPod touch 3g (8 gig) around christmas, and its been a truly great buy and worked flawlessly. However just recently I started having issues with the iPod's music player.
Ever since last night, I noticed that when I use the music player, and try to move 'FORWARD' a song (IE the double forward arrow button) the arrow would stay white like I was pressing it, NOT move forward a song, the screen would be unresponsive as the current song played, and then after 2-3 seconds the music player would crash and go back to the home screen.
I know it was a crash because when I went back to the music player, it was reset back to the 'Shuffle' option with the list of songs below it (usually, it leaves off on the last song you were listening to.)
I also noticed, that even if I just listened to a song completely without hitting forward, it would STILL freeze up and crash to home screen once the song was finished, even if I DIDN'T press anything.
But apparently the double back arrow (rewind/back) works without crashing it.
So my question is: what can I do to fix this? I already tried restarting my iPod (by holding the top and home buttons for 10 seconds) and it did not solve this. I always keep my iPod charged up, and I can't think of ANYTHING I did yesterday or recently at all to cause this problem....I generally only use the iPod touch for music or internet browsing.
any help appreciated..
-Ben
Message was edited by: Eep25

33 replies, no posts

I HAVE PROBLEM WITH ITUNES cant download music with itunes to iphone 5 16gb ,,waiting for changes to be applied''

I HAVE PROBLEM with itunes i want to download music to iphone 5 16gb from itunes WHERE is writting ,,waiting for changes to be applied'' if you help me i will very content

so i went back to the apple store and the only solution was to trade in your phone for a new one because there was a faulty conector in the microport. hopefully you have a waranty and your stuff backed up!

G530 - problems with the "easy program access" key

I have a 3000 G530 (model 4151) laptop, and so far I haven't really had any problems with it. Although recently, something happened with a little touch-sensitive button above my keyboard, in the upper right, next to the volume controls. I guess what it does is you can set it so that whenever you press it, it will just open up the program or document that you set it to. I'm not sure how this happened, but recently it started acting like I was repeatedly pressing it over and over. The setup window for the key opened about twice a second. I restarted my computer, and tried pressing the key. I set it to open a document I had (just to test it), and now it just opens up that document whenever I press it. Occassionally it will randomly open the document over and over, even when my hands were nowhere near it. Anyone know how I can fix this?

Did a little workaround... and all things went like a candy :)
I simply had to enter in the web.xml
<servlet-mapping>
<servlet-name>Index</servlet-name>
<url-pattern><path>/Index</url-pattern>
</servlet-mapping>
IDE is trully beautiful, many new features (will definately try CVS)...
But with my 1Gb RAM its hard game, previous Jdeveloper version used much less memory :(

Messaging problem with N91

hi,
i am using an n91 phone for the past 7 months. But since 3 or 4 months i am facing a problem with the messaging feature. After i send a message the phone gets hang, displaying " sending message" for more than one minute.Then the message is sent and delivered. At this time i cant do anything with the phone,the phone is completely hang.Then I approached a near by nokia service center and they fixed the problem by formatting the phone. But after 3 or 4 weeks the problem came back agn and now i have to wait more than one minute after i send a message. How can i permenantly fix this problem?

Install the SMS accelerator found in the link below, it should fix it permanently.
http://www.nokia.co.uk/A4222054

[Solved] Strange problem with my '/home/evert/Music' folder

Good evening everybody,
I'm having since a few weeks some very strange problems with one directory on my hard disk: '/home/evert/Music/'.
The problem is that this directory excists, with all it's subfolders. But i can't see a single file (mostly mp3's) in that folder or subfolders.
Some more background information to make sure i'm not doing something wrong :
http://pastebin.be/4419 : the log file of a 'mpd --create-db' command. This clearly shows that mpd fills his database with the music. And even more, i'm able to play all that music.
evert@localhost ~/Music $ du --max-depth=1 -h -c | tail -n 1
15G total
So this folder really excists and is filled with a lot of music files normally .
evert@localhost ~/Music/Metallica/loaded $ ls -a
Strange ? In this folder really was music acording to the mpd --create-db log file ?!
drwxr-xr-x 161 evert users 8192 2007-08-10 17:57 Music
As user i'm having all rights to this folder, so that isn't the fault.
Even when trying to see the files, neither konq in su mode or MC works.
Anybody who knows something more about this problem or could help me a bith further pls ? I'm running XFS as filesystem on this partition.
Thanks in advance,
Evert
Last edited by evert_ (2007-08-13 19:23:36)

MrWeatherbee wrote:
shining wrote:You don't have anything in ~/Music/Metallica/loaded but you have stuff in ~/Music/Music/Metallica/loaded
It's really an awful mess, I would suggest you clean your music folders.
Shall he clean his room, too?
If his home is as messy as his $HOME, then yes, totally.

Problems with X-Fi Xtreme Music and Virtual Instrume

I am using Cakewalk's Sonar Home Studio 6?XL and MOTU Symphonic Instrument. I have some virtual instruments that are less detailed that seem to run great, but so far I can't play MOTU SI in stand alone mode without getting po
ps.
I can play it in Cakewalk, but I can not assign a MIDI file to it and have it play it without getting the same kind of pops I was getting in stand alone mode. I read an earlier post about problems with NVidia and that is the maker of my motherboard. I have not had any problems with the pops in instances where I am just playing audio from a CD or?by playing a wav. or mp3. I bought this card because of the the ASIO?2.0 compatibility, but I am starting to have my doubts on whether or not this card can handle what Creative claims. Anyone got any ideas? I appreciate any help I can get.

Have You forget? You are back in the 80's again! Use Creative Cr..s Mode Switcher and manually switch to Game Mode. And don't forget to manually switch to other Mode before launching any other applications. If You don't have Mode Switcher (Volume Panel) in system tray and obvoiusly don't have any system slowdowns and not experioncing high RAM usage that means You don't have Creative Bloatware installed. You can find it on X-Fi instllation CD.
Have fun and thank Creative marketing and programming crews for this! Message Edited by cryogenic on 06--2006 0:09 AM

Problems with N91(GSM) multimedia/music key

Similar Messages

Maybe you are looking for