Problems with Nforce4 install - audio/ethernet/raid

Just installed my Neo4 Platinum Nforce4 with XP Home SP2. I have a problem with the drivers. I went to the Nvidia site and download both the Unified Drivers and the standalone Kit for XP.
The unified driver set didn't seem to do anything at all, it seemed to quit half way through the install without giving me any finished message. A quick look in device manager and I saw about seven items with yellow warnings!
I then tried the standalone kit which worked better, however after the install I am still left with 3 items in device manager that are giving me warnings. Multimedia Audio Controller, Ethernet Controll & Serial ATA RAID controller. I have no audio at all, I just the BIOS is all is OK, as it is for everything else. In the sound section of control panel there is no audio hardware available.
Can anyone help please? I dunno what I could have done wrong. It's a fresh install.

I have now done eveything you've said. I installed the Nforce drivers off the CD, and then installed Realtek, Ethernet & RAID via Live update. I also tried to do the NVMixer & Nvidia Audio install install. I installed realtek from the add/remove software menu. I then went into add new hardware and did manual install, show all hardware, have disk. Then I browsed to the Nvidia Audio codec folder on my desktop that I download. I was given an option of two drivers "nvmcp" & "nvmpu". I picked the first and ended up choosed "Nvidia audio codec interface" which then installed. It then appeared in device manager. However, when I clicked the audio panel in control panel I still get no audio device installed? I then tried to install NVMixer and when I try to run the application I get this message:
"the application cannot start because it could not detect any NVIDIA Nforce hardware on your system...."
What am I doing wrong? When I did the driver install there were two things listed in each driver "nvidia audio codec interface" and also "nvidia audio processing unit", which should I be choosing? Even if I try and installed the "MVP audio processing unit" I'll get a code(10) device cannot start in device manager. This is kinda confusing.
I also wondered about the RAID controller software. The silicon image drivers that came on the MSI seem horrible, they installed Java too. Is there any way to disable this controller? In the BIOS I can only see one option to enable RAID and when this is enabled device mananger will show an error on an "unknown device". I assume this is the NVRaid? and speaking of NVraid which is mentioned in big fat type on the back of the MSI box, so far I've seen or heard none of it during this installtion?

Similar Messages

"there is a problem with your apple tv ethernet networking" but I am connecting wirelessly

So basically I can happily see all my movies etc on my TV via Apple TV but they appear to play but with no image. Sound is OK! Then the ATV decides something is wrong, reboots and says "there is a problem with your apple tv ethernet networking" but I am trying to connect over wifi.
I have original ATV
Thanks in advance
Daniel

You may have some software corruption or the unit may well be starting to fail.
Hold menu and down arrow for 6 secs to reboot the unit to the diagnostics/service menu from where you can reinstall the original shipping software (some have had issues updating beyond version 1.0 if that's what's on it) but first I'd try to run the diagnostics utility though it often passes this even if there are issues.
Always worth unpowering the AppleTV and letting it rest for a few minutes before restarting - this can sometimes reset thing that a powered reboot won't.

My sound is like echo and i can't solve the problem with realtek hd audio manager

HP G72 notebook
Windows 7 64 bit
Sound is like echo and can't solve problem with Realtek HD audio manager

It's a Qosmio X300-16M (windows 7 64bit)
I downloaded the last toshiba's sound driver (for win 7 64bit), but it's as if it doesn't contain MaxxAudio anymore... (but the file maxxaudio.dll is still in realtek directory)
It worked correctly after Windows 7 update, (that's why I tried to reinstall the audio drivers which were in the DVD... but it does not have resolved the problem.)
And all my system restore's points have been lost after a wrong bios update or something else (but this isn't a problem anymore)
Now, my computer works correctly, my only problem is that the MaxxAudio tab (from Waves Audio) in the realtek audio manager disappeared... (It just makes a better sound...)
And I just want to know if it's a curent problem or not... and if someone can fix it

[Solaris 10] Installation problem on nForce4 Ultra - SATA II - raid 0

hi,
Like I was read on HW web page, Solaris 10 should work fine with 'nForce4' (without 'Ultra'),
but on mine mainboard (nForce4 Ultra) instalator was unable to found my array.
I have ASUS A8N-E (nForce4 Ultra) with 2x 250GB Seagate on SATA II RAID 0.
Is it posible to install this OS on 'nForce4 Ultra' or maybe I am doing sth wrong ?

Hi, I have the similiar problems on Solaris 10 installation.
I have a Compaq SR1710 AMD Sempron™ + 1GB RAM. I am trying make it a mini workstation.
However, the installation was never able to throught.
It always stop or freeze on the "dos" screen after I select "interactive" installation.
The last error message I got was something "Skipped rtls01" something.
I am trying to install Solaris 9 now, so far on disc 2.
Very smooth. No problem..
hope someone can give me advise on how to install version 10 on the machine.
BTW, I checked teh HCL. It seems ok, given my machine is very basic.

Problem with keyboard and audio on Satellite L40

Hi everybody,
I just installed XP SP2 on my Satellite L40 (BTW thanx to all you that have helped me overcome the problems during this operation with your threads), but I have some problem with my keyboard. I have an azerty keyboard and after I installed xp, it worked as a qwerty, I repared it, now all my letters are working fine, but i have some problems with some symbols, such as @, !, _,if you understand me.
Could somebody help me???
I also have problems with my audio, in fact I have no audio at all, in control panel it says that no audio device is found.
I saw some threads that said that I should first install kb888111, and another likely thing, but i can't find the other one. I've downloaded the sound driver from the toshiba website; thanx for helping me in that field also.
bye

I have the same problem with sound...I have found hotfix kb888111 and I instaled that one...but when i wanted to start instaling sound driver a popup window say thet there is some error and can't continue with instaling sound driver...
I found hotfix kb888111 in this folder which i have downladed from toshiba site: english\sound driver\mshdqfe\win2k_xp\us\kb888111xps2....
i do not know what to do.....Does anybody else knows....

Problem with the IDT audio driver.

Hi
i got a problem with my audio driver yesterday. while watching a video the driver stopped working and it says that "no audio output installed". i tried reinstalling the idt software from hp website. but it is no help, in the middle of the installation process the computer is showing an error saying that the idt software is not compatible with the hardware detected.
I need my audio drivers as soon as possible as i have a presentation to do. Please help asap.!!

Hi
First uninstall the software from program and features.
Or, you can uninstall IDT Audio Driver from your computer by using the Add/Remove Program feature in the Window's Control Panel.
On the Start menu (for Windows 8, right-click the screen's bottom-left corner), click Control Panel, and then, under Programs, do one of the following:
Windows Vista/7/8: Click Uninstall a Program.
Windows XP: Click Add or Remove Programs.
When you find the program IDT Audio Driver, click it, and then do one of the following:
Windows Vista/7/8: Click Uninstall.
Windows XP: Click the Remove or Change/Remove tab (to the right of the program).
Follow the prompts. A progress bar shows you how long it will take to remove IDT Audio Driver.
Please try to install this software and see if this fixes your issue. In case this does not work try performing system restore to the date where unit was working fine.
http://h20564.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_130088_1
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

MSI Z87m problems with Realtek install

I cannot install Realtek drivers with this motherboard. Brand-new system with Windows 7. Intel I5 CPU, gigabyte gtx 780, 8 GB ram. All drivers updated, win 7 updated.
I have tried the drivers from the included disc and also direct from Realtek site. They will install but they will not work. Red Cross shows up on the volume icon anytime I try to open audio.
I have even tried reinstalling the OS twice. Makes no difference.
I tried installing the Realtek drivers from SafeBoot. I just get an error message.
Creative Sound Blaster cinema will also not work because the RealTek drivers don't work.
I have read a few other posts of people having this exact same problem with this motherboard and Realtek drivers.
The windows HD audio will work.
Right clicking on Realtek properties in device manager shows everything is working fine, even though it isn't.
I have also had problems when booting into the bios. If I try to change anything, like a fan setting, and then try to save and exit, the system freezes. I had to CMOS once already. Pc also freezes in the bios when trying to access the hardware Monitor option, requiring a reboot. The other options work fine.
I've written to MSI about this problem but I was hoping somebody might have an idea of what I could try before I take the system back to the store for them to check it and replace the motherboard, as I will then be without the PC for a week.

What xmad is trying to get as information is the 'complete' name of the mainboard. Z87m is not good enough. Also, more information about the other systems components including specifics of the RAM, brand, rated speed, and the PSU brand and description. For now, test with just a single RAM stick.

Problem with fibre channel card and raid system after upgrading to 10.4.7

Hello, I have a problem with our Xserve G4 DP. After the installation of 10.4.7 everything works fine exept our fibre channel card. This card is connected to a Hitachi Raid System which worked fine over a year. But after the update the volume was no longer mounted. I even reinstalled the server to 10.4.4 and no sign of our raid volume. Using the apple fibre channel utiltiy 2.0, I see that there is a connection - but still the raid volume is not mounted. When I restart the server the lights on the back of the card are shortly flickering and sending some packets to the raid system but that´s all. Has anybody an idea?
Greetings from Heidelberg
Klaus
Xserve G4 DP 1 GHz Mac OS X (10.4.6) Mac OSX Server 10.4.7

You could re-update, by downloading the 10.4.7 Combination Updater from Apple.

It's now over 6 weeks since I made the mistake of updating my iPad and I am furious and frustrated at the lack of a solution to the problem with ios 5 audio app missing lyrics

It’s now over 6 weeks since I made the mistake of updating my iPad and I am furious and frustrated at the lack of a solution to the problem with ios 5.
I recently updated to ios 5.1 but nothing has been done to rectify the audio app problems ie lyrics no longer shown,
I am extremely disappointed and angrywith those responsible for the iOS 5 update, in regard to the way it hasaffected the music app in my iPad.
I also own an iPhone 4, am an avid Apple fan, and up until now have beenextremely pleased with the devices, and have sung their praises to friends andassociates.
I am a professional musician, and purchased an iPad primarily to use with theperformance of my music.
The changes made to the music app affected my performances over the weekendextremely adversely – limiting my repertoire and causing confusion and delays.
I have spent many hours talking withApple helpline assistants (who, incidentally have been very good and have triedto help), and I have also spent a lot of time on this letter.
I greatly regret updating to iOS 5.
There are two major problems with the music app.
1. Lyrics no longer displayed
2. Layout, and appearance and consequently performance have seriouslyregressed.
I have a repertoire of around 500 song backing tracks, organised into about 20playlists, half of which featured lyrics / chords that I have spent monthsrecently entering into iTunes so that they could be used on my iPad.
These were working fine up until the update - now they are gone.
Previously, the app featured large icons for playlist, artists, songs etc. atbottom of page: Now there are small, grey, indistinct barely legible buttons.
Previously, when playlist icon was selected - all the playlists were listedclearly in order on the left hand side in black on white (as in iTunes).
Now they are scattered across the whole page in large squares (displayingnothing if there is no album art).
The identifying wording below eachsquare is now small, grey, indistinct & barely legible.
Previously, when a playlist was selected - the songs were displayed in adescending list in black & white: now they appear as small, grey indistinct & barely legible.
Previously, when a song was selected - it appeared filling the page, and withaudio controls clearly positioned at top of screen. One tap would bring uplyrics.
Now audio controls appear at top once again small, grey, indistinct &barely legible.
A small square representsalbum art which if tapped fills page. A further tap fails to bring up lyrics.
Don Wilson

Lyrics aren't supported in the Music app on iOS 5 on the iPad. These are user-to-user forums, they are not monitored by Apple (there are too many forums/threads/messages for that to happen). If you want to leave feedback for Apple then you can do so here : http://www.apple.com/feedback/ipad.html

Problems with image and audio in Premiere

Hi! I'm using Premiere Elements 9, but there's no synchronization with imagen and audio because the image is slower than audio and it's causing problems when I'm editing. Why can I do? It's there a poblem that can I fix in "Preferences" or is my laptop?
I hope your answer,

When you do post the PrE forum, this ARTICLE will give you tips on the types of info, that will be so useful. See you there!
Good luck,
Hunt

I'm having problems with the install of iTunes 10.7 it seems to be going well and then at the very end of the blue bar it doesnt seem to complete? All of my software is up to date and plenty of space on the mini?

I'm having problems installing iTunes 10.7. It seems to be going well and then at the last part of the blue bar it just doesn't complete. All software is up to date and there is plen of room on the mini? I have tried like 4 times and am ready to throw it out the window.

I noticed some problems with the Apple Support sites here the last day or so.
Try again using > Apple - iTunes - Download iTunes Now

Metalink SR category for problem with CRS install

HI
Can You please tell me , where I find in SR category to create request on metaling about problem with install/start crs :
I wont to create RAC env where host is ORACLE VM and clusterware is OCFS2 and wit Oracle Enterprise linux 5 , but after istal ai have problem with start crs (root.sh) and I don't know to find relevant category
[root@lin1 bin]# ./crsctl start cluster
CRS-2672: Attempting to start 'ora.gipcd' on 'lin1'
CRS-2672: Attempting to start 'ora.mdnsd' on 'lin1'
CRS-2676: Start of 'ora.mdnsd' on 'lin1' succeeded
CRS-2676: Start of 'ora.gipcd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.gpnpd' on 'lin1'
CRS-2676: Start of 'ora.gpnpd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssdmonitor' on 'lin1'
CRS-2676: Start of 'ora.cssdmonitor' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssd' on 'lin1'
CRS-2672: Attempting to start 'ora.diskmon' on 'lin1'
CRS-2676: Start of 'ora.diskmon' on 'lin1' succeeded
CRS-2674: Start of 'ora.cssd' on 'lin1' failed
CRS-679: Attempting to clean 'ora.cssd' on 'lin1'
CRS-2681: Clean of 'ora.cssd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssdmonitor' on 'lin1'
CRS-2676: Start of 'ora.cssdmonitor' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssd' on 'lin1'
CRS-2674: Start of 'ora.cssd' on 'lin1' failed
CRS-2679: Attempting to clean 'ora.cssd' on 'lin1'
CRS-2681: Clean of 'ora.cssd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.diskmon' on 'lin1'
CRS-2676: Start of 'ora.diskmon' on 'lin1' succeeded
CRS-2673: Attempting to stop 'ora.cssdmonitor' on 'lin1'
CRS-2677: Stop of 'ora.cssdmonitor' on 'lin1' succeeded
CRS-4000: Command Start failed, or completed with errors.
[root@lin1 bin]# ./crsctl check cluster
CRS-4535: Cannot communicate with Cluster Ready Services
CRS-4530: Communications failure contacting Cluster Synchronization Services daemon
CRS-4534: Cannot communicate with Event Manager
[root@lin1 bin]# ./crsctl check cluster -all
lin1:
CRS-4535: Cannot communicate with Cluster Ready Services
CRS-4530: Communications failure contacting Cluster Synchronization Services daemon
CRS-4534: Cannot communicate with Event Manager
Thank You Brano

HI
Can You please tell me , where I find in SR category to create request on metaling about problem with install/start crs :
I wont to create RAC env where host is ORACLE VM and clusterware is OCFS2 and wit Oracle Enterprise linux 5 , but after istal ai have problem with start crs (root.sh) and I don't know to find relevant category
[root@lin1 bin]# ./crsctl start cluster
CRS-2672: Attempting to start 'ora.gipcd' on 'lin1'
CRS-2672: Attempting to start 'ora.mdnsd' on 'lin1'
CRS-2676: Start of 'ora.mdnsd' on 'lin1' succeeded
CRS-2676: Start of 'ora.gipcd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.gpnpd' on 'lin1'
CRS-2676: Start of 'ora.gpnpd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssdmonitor' on 'lin1'
CRS-2676: Start of 'ora.cssdmonitor' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssd' on 'lin1'
CRS-2672: Attempting to start 'ora.diskmon' on 'lin1'
CRS-2676: Start of 'ora.diskmon' on 'lin1' succeeded
CRS-2674: Start of 'ora.cssd' on 'lin1' failed
CRS-679: Attempting to clean 'ora.cssd' on 'lin1'
CRS-2681: Clean of 'ora.cssd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssdmonitor' on 'lin1'
CRS-2676: Start of 'ora.cssdmonitor' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.cssd' on 'lin1'
CRS-2674: Start of 'ora.cssd' on 'lin1' failed
CRS-2679: Attempting to clean 'ora.cssd' on 'lin1'
CRS-2681: Clean of 'ora.cssd' on 'lin1' succeeded
CRS-2672: Attempting to start 'ora.diskmon' on 'lin1'
CRS-2676: Start of 'ora.diskmon' on 'lin1' succeeded
CRS-2673: Attempting to stop 'ora.cssdmonitor' on 'lin1'
CRS-2677: Stop of 'ora.cssdmonitor' on 'lin1' succeeded
CRS-4000: Command Start failed, or completed with errors.
[root@lin1 bin]# ./crsctl check cluster
CRS-4535: Cannot communicate with Cluster Ready Services
CRS-4530: Communications failure contacting Cluster Synchronization Services daemon
CRS-4534: Cannot communicate with Event Manager
[root@lin1 bin]# ./crsctl check cluster -all
lin1:
CRS-4535: Cannot communicate with Cluster Ready Services
CRS-4530: Communications failure contacting Cluster Synchronization Services daemon
CRS-4534: Cannot communicate with Event Manager
Thank You Brano

Problem with the instalation/launching of Itunes 7.1

first of all...I upgraded MSN 7.5 to live messenger (big mistake) and since I wasn't happy with it I tried to return to my old msn,so I made a restore system to 2 days before that,no problem here,but after that I tried to launch iTunes and it couldn't open, arguing it can't launch because there's a problem with my audio config
I tried to fix this with the guide in the site and it still doesn't work, I uninstalled and reinstalled both versions (7 and 7.1) and both have the same error,also my msn doesn't have any sounds so...maybe that **** crappy live messenger f*cked up some of my config but as much as I do I can't figure it out how to fix it.
anyone please help me here

it can't launch because there's a problem with my audio config
typically that's caused by a problem with your QuickTime. (iTunes uses QuickTime for video and audio playback.)
the following document may be of some help with that:
iTunes 7 for Windows: iTunes had detected an audio configuration problem

Problems with new instalation of Photoshop Elements 12

Windows 7
I have had continual problems with PE 9 with error messages to uninstall and reinstall Error 16.
So I thought buy version 12 that should do the trick BUT NO I uninstalled version 9 and installed 12 from disk on the 20th August.
Updated with Application Manager and all was well. Yesterday will not load and Error 16 as before. Tried run as administrator and was told I needed a newer version of Update Manager. Downloaded and installed version 8 still no joy and this then updated to Adobe Creative Cloud. The Application still will not open and I am getting fed up with Adobe applications, when they work their fine but I have no luck getting them to work long term.
Having bought this I am reluctant to move on and incur the cost of an alternative but I am fast running out of patience with Adobe
Any Hep Would Be Appreciated

Barbara B
Thanks for link. Worked through Windows Vista/7 settings got to Set permissions but no Adobe PCD folder. Uninstalled and reinstalled PE 12 software 5/9, PCD now there and application running OK as was the initial installation.
6/9 on start-up, Creative Cloud identified update for PE 12, Application Manager appeared and I run update, after, application running OK and Adobe PCD still there. Checked settings and permissions against link document permissions not as suggested but application working so made no changes.Will the application continue to work, that’s the next question, from previous experience with the initial installation and with PE 9, I have my doubts.
If the loss of Adobe PCD is the cause of the problem, what makes it disappear ?
Les

Problems with imported mono audio with stereo HD video FCE4

This is with Final Cut Express 4.
So here is what I am doing: I am recording video of my flight lessons inside my airplane with a mounted Panasonic HDC-TM90 HD camera. Since it is noisy inside the plane, I am using an Olympus VN-4100PC digital voice recorder to pick up the Air Traffic Control and Intercom within the airplane (between me and my instructor) which is 22 KHZ mono. I am doing this because I want the sound of the airplane and also the communication so everything works together and you get the best of both worlds (otherwise you would hear one or the other and that's pretty boring). Ok, enough with the intro.
Here is what I am having problems with -- when I get the video, stereo audio with the video and the mono audio all lined up in FCE in my timeline, it starts to get out of sync about 10 minutes or so into the film. And it gets worse as the film goes on. This is driving me nuts and I have NO idea out to fix it.
The only thing I can think of is that my Digital Voice Recorder is recording at a slightly faster speed than the camera's audio and this is why it gets out of whack.
Does anyone have any suggestions on how to fix this? Or at least give me an explanation why it is happening?
Thanks for any help!!

Thanks for the reply. I did this and it still doesn't seem to be matching up properly. Tell me if maybe I missed something.
1. I took the original .WAV file from my Digital Recorder and imported it into iTunes and then converted it into an .AIFF.
2. I took the .AIFF file and imported it into MPEG Streamclip and exported it as another .AIFF file that was Stereo and 48kHz.
Is there a step I missed?

Problems with Nforce4 install - audio/ethernet/raid

Similar Messages

Maybe you are looking for