Problems with nouveau and KMS

Hi guys,
tl;dr: Want to have a GUI, tried to get it on my own, got stuck at
(EE) [drm] KMS not enabled
(though it should be enabled) and no GUI
It would be nice if someone little bit more expirienced could help (and perhaps explain) a little bit...
So here's the long version (In case I messed things up without noticing):
I installed arch on an old machine. After first reboot screen hung at
root: clean, 53232/1310720 files, 906718/5242880 blocks
Got past that installing proprietary nvidia drivers (nvidia-304xx for the GeForce 7500 LE).
Testing X failed. Got X working with nouveau driver.
Rebooted and again hung at
root: clean, 53232/1310720 files, 906718/5242880 blocks
(So proprietary: terminal, but no X - nouveau: No terminal, but X)
Tried autologin and start X at login: Same result.
According to the wiki, KMS
is required by the Nouveau driver
and according to http://nouveau.freedesktop.org/wiki/KernelModeSetting/
KMS is on by default
But according to
/var/log/Xorg.0.log
(EE) [drm] KMS not enabled
Did some more reading (especially http://nouveau.freedesktop.org/wiki/TroubleShooting/ was helpful) but found no useful information (eg. on how to enable KMS), so I decided to ask for help...
Here's the full Xorg.0.log (What else would be useful?):
[ 26.378]
X.Org X Server 1.15.0
Release Date: 2013-12-27
[ 26.378] X Protocol Version 11, Revision 0
[ 26.378] Build Operating System: Linux 3.12.5-1-ARCH x86_64
[ 26.378] Current Operating System: Linux plaything 3.12.9-1-ARCH #1 SMP PREEMPT Sun Jan 26 09:01:37 CET 2014 x86_64
[ 26.378] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=a37b4e97-dcfd-40be-a0eb-9307e545ff61 rw quiet
[ 26.378] Build Date: 09 January 2014 08:47:24AM
[ 26.379]
[ 26.379] Current version of pixman: 0.32.4
[ 26.379] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 26.379] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 26.379] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Jan 30 23:02:22 2014
[ 26.421] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 26.437] (==) No Layout section. Using the first Screen section.
[ 26.437] (==) No screen section available. Using defaults.
[ 26.437] (**) |-->Screen "Default Screen Section" (0)
[ 26.437] (**) | |-->Monitor "<default monitor>"
[ 26.446] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 26.446] (**) | |-->Device "n"
[ 26.446] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 26.446] (==) Automatically adding devices
[ 26.446] (==) Automatically enabling devices
[ 26.446] (==) Automatically adding GPU devices
[ 26.466] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 26.466] Entry deleted from font path.
[ 26.466] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 26.466] Entry deleted from font path.
[ 26.466] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 26.466] Entry deleted from font path.
[ 26.466] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 26.467] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 26.467] Entry deleted from font path.
[ 26.467] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 26.467] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 26.467] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 26.467] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 26.467] (II) Loader magic: 0x804c80
[ 26.467] (II) Module ABI versions:
[ 26.467] X.Org ANSI C Emulation: 0.4
[ 26.467] X.Org Video Driver: 15.0
[ 26.467] X.Org XInput driver : 20.0
[ 26.467] X.Org Server Extension : 8.0
[ 26.470] (--) PCI:*(0:2:0:0) 10de:01dd:174b:2510 rev 161, Mem @ 0xdc000000/16777216, 0xc0000000/268435456, 0xdd000000/16777216, BIOS @ 0x????????/131072
[ 26.471] (II) Open ACPI successful (/var/run/acpid.socket)
[ 26.472] Initializing built-in extension Generic Event Extension
[ 26.472] Initializing built-in extension SHAPE
[ 26.472] Initializing built-in extension MIT-SHM
[ 26.472] Initializing built-in extension XInputExtension
[ 26.472] Initializing built-in extension XTEST
[ 26.472] Initializing built-in extension BIG-REQUESTS
[ 26.472] Initializing built-in extension SYNC
[ 26.472] Initializing built-in extension XKEYBOARD
[ 26.472] Initializing built-in extension XC-MISC
[ 26.472] Initializing built-in extension SECURITY
[ 26.472] Initializing built-in extension XINERAMA
[ 26.472] Initializing built-in extension XFIXES
[ 26.472] Initializing built-in extension RENDER
[ 26.472] Initializing built-in extension RANDR
[ 26.472] Initializing built-in extension COMPOSITE
[ 26.472] Initializing built-in extension DAMAGE
[ 26.472] Initializing built-in extension MIT-SCREEN-SAVER
[ 26.472] Initializing built-in extension DOUBLE-BUFFER
[ 26.472] Initializing built-in extension RECORD
[ 26.472] Initializing built-in extension DPMS
[ 26.472] Initializing built-in extension Present
[ 26.472] Initializing built-in extension DRI3
[ 26.472] Initializing built-in extension X-Resource
[ 26.472] Initializing built-in extension XVideo
[ 26.472] Initializing built-in extension XVideo-MotionCompensation
[ 26.472] Initializing built-in extension XFree86-VidModeExtension
[ 26.472] Initializing built-in extension XFree86-DGA
[ 26.472] Initializing built-in extension XFree86-DRI
[ 26.472] Initializing built-in extension DRI2
[ 26.472] (II) LoadModule: "glx"
[ 26.482] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 26.719] (II) Module glx: vendor="X.Org Foundation"
[ 26.719] compiled for 1.15.0, module version = 1.0.0
[ 26.719] ABI class: X.Org Server Extension, version 8.0
[ 26.719] (==) AIGLX enabled
[ 26.719] Loading extension GLX
[ 26.719] (II) LoadModule: "nouveau"
[ 26.720] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 26.781] (II) Module nouveau: vendor="X.Org Foundation"
[ 26.781] compiled for 1.15.0, module version = 1.0.10
[ 26.781] Module class: X.Org Video Driver
[ 26.781] ABI class: X.Org Video Driver, version 15.0
[ 26.781] (II) NOUVEAU driver
[ 26.782] (II) NOUVEAU driver for NVIDIA chipset families :
[ 26.782] RIVA TNT (NV04)
[ 26.782] RIVA TNT2 (NV05)
[ 26.782] GeForce 256 (NV10)
[ 26.782] GeForce 2 (NV11, NV15)
[ 26.782] GeForce 4MX (NV17, NV18)
[ 26.782] GeForce 3 (NV20)
[ 26.782] GeForce 4Ti (NV25, NV28)
[ 26.782] GeForce FX (NV3x)
[ 26.782] GeForce 6 (NV4x)
[ 26.782] GeForce 7 (G7x)
[ 26.782] GeForce 8 (G8x)
[ 26.782] GeForce GTX 200 (NVA0)
[ 26.782] GeForce GTX 400 (NVC0)
[ 26.782] (++) using VT number 1
[ 26.783] (EE) [drm] KMS not enabled
[ 26.783] (EE) No devices detected.
[ 26.783] (EE)
Fatal server error:
[ 26.783] (EE) no screens found(EE)
[ 26.783] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 26.783] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 26.783] (EE)

First thanks for answering
Checked dmesg but it does not mention KMS (dmesg | grep KMS returns nothing)
and I was not able to find a virtualisation option in my BIOS.
Also I didn't find something similar looking over dmesg...
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.12.9-1-ARCH (tobias@T-POWA-LX) (gcc version 4.8.2 20131219 (prerelease) (GCC) ) #1 SMP PREEMPT Sun Jan 26 09:01:37 CET 2014
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=a37b4e97-dcfd-40be-a0eb-9307e545ff61 rw quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000005fedffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000005fee0000-0x000000005fee2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000005fee3000-0x000000005feeffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000005fef0000-0x000000005fefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Packard Bell BV IMEDIA MC 9745/Cuba MS-7301, BIOS W7301VP2.027 10/27/2006
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP bridge at 00:00:00
[ 0.000000] Aperture from AGP @ d0000000 old size 32 MB
[ 0.000000] Aperture from AGP @ d0000000 size 128 MB (APSIZE f20)
[ 0.000000] e820: last_pfn = 0x5fee0 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CDFFF write-protect
[ 0.000000] CE000-EFFFF uncachable
[ 0.000000] F0000-F7FFF write-through
[ 0.000000] F8000-F8FFF uncachable
[ 0.000000] F9000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 040000000 mask FE0000000 write-back
[ 0.000000] 2 base 0D0000000 mask FF8000000 write-combining
[ 0.000000] 3 base 05FF00000 mask FFFF00000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [mem 0x000f46e0-0x000f46ef] mapped at [ffff8800000f46e0]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b32000, 0x01b32fff] PGTABLE
[ 0.000000] BRK [0x01b33000, 0x01b33fff] PGTABLE
[ 0.000000] BRK [0x01b34000, 0x01b34fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x5fc00000-0x5fdfffff]
[ 0.000000] [mem 0x5fc00000-0x5fdfffff] page 2M
[ 0.000000] BRK [0x01b35000, 0x01b35fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x5c000000-0x5fbfffff]
[ 0.000000] [mem 0x5c000000-0x5fbfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x5bffffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x5bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x5fe00000-0x5fedffff]
[ 0.000000] [mem 0x5fe00000-0x5fedffff] page 4k
[ 0.000000] BRK [0x01b36000, 0x01b36fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x37a02000-0x37cf8fff]
[ 0.000000] ACPI: RSDP 00000000000f8ae0 00014 (v00 PacBel)
[ 0.000000] ACPI: RSDT 000000005fee3040 0003C (v01 PacBel PackBell 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP 000000005fee30c0 00074 (v01 PacBel PackBell 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT 000000005fee3180 06523 (v01 PACBEL AWRDACPI 00001000 MSFT 0100000E)
[ 0.000000] ACPI: FACS 000000005fee0000 00040
[ 0.000000] ACPI: SLIC 000000005fee9800 00176 (v01 PacBel PackBell 42302E31 AWRD 00000000)
[ 0.000000] ACPI: MCFG 000000005fee99c0 0003C (v01 PacBel PackBell 42302E31 AWRD 00000000)
[ 0.000000] ACPI: APIC 000000005fee9700 00090 (v01 PacBel PackBell 42302E31 AWRD 00000000)
[ 0.000000] ACPI: SSDT 000000005fee9a40 0015C (v01 PmRef Cpu0Ist 00003000 INTL 20040311)
[ 0.000000] ACPI: SSDT 000000005fee9ed0 002F1 (v01 PmRef CpuPm 00003000 INTL 20040311)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000005fedffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x5fedffff]
[ 0.000000] NODE_DATA [mem 0x5fedb000-0x5fedffff]
[ 0.000000] [ffffea0000000000-ffffea00017fffff] PMD -> [ffff88005de00000-ffff88005f5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x5fedffff]
[ 0.000000] On node 0 totalpages: 392830
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 6076 pages used for memmap
[ 0.000000] DMA32 zone: 388832 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfecc0000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 5, version 3, address 0xfecc0000, GSI 24-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 64
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] e820: [mem 0x5ff00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88005fc00000 s86464 r8192 d24128 u524288
[ 0.000000] pcpu-alloc: s86464 r8192 d24128 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 386669
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=a37b4e97-dcfd-40be-a0eb-9307e545ff61 rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] AGP bridge at 00:00:00
[ 0.000000] Aperture from AGP @ d0000000 old size 32 MB
[ 0.000000] Aperture from AGP @ d0000000 size 128 MB (APSIZE f20)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 1531400K/1571320K available (5119K kernel code, 807K rwdata, 1628K rodata, 1144K init, 1288K bss, 39920K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:8448 nr_irqs:1024 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 6291456 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2792.957 MHz processor
[ 0.006674] Calibrating delay loop (skipped), value calculated using timer frequency.. 5588.66 BogoMIPS (lpj=9309856)
[ 0.011289] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.012344] Mount-cache hash table entries: 256
[ 0.012786] Initializing cgroup subsys memory
[ 0.012820] Initializing cgroup subsys devices
[ 0.012825] Initializing cgroup subsys freezer
[ 0.012829] Initializing cgroup subsys net_cls
[ 0.012833] Initializing cgroup subsys blkio
[ 0.012883] CPU: Physical Processor ID: 0
[ 0.012887] CPU: Processor Core ID: 0
[ 0.012891] mce: CPU supports 4 MCE banks
[ 0.012913] CPU0: Thermal monitoring enabled (TM1)
[ 0.012928] Last level iTLB entries: 4KB 128, 2MB 128, 4MB 128
Last level dTLB entries: 4KB 64, 2MB 0, 4MB 64
tlb_flushall_shift: 6
[ 0.013032] Freeing SMP alternatives memory: 20K (ffffffff819e9000 - ffffffff819ee000)
[ 0.014523] ACPI: Core revision 20130725
[ 0.020923] ACPI: All ACPI Tables successfully acquired
[ 0.021923] ftrace: allocating 20320 entries in 80 pages
[ 0.030837] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.066011] smpboot: CPU0: Intel(R) Pentium(R) D CPU 2.80GHz (fam: 0f, model: 06, stepping: 04)
[ 0.066666] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[ 0.066666] ... version: 0
[ 0.066666] ... bit width: 40
[ 0.066666] ... generic registers: 18
[ 0.066666] ... value mask: 000000ffffffffff
[ 0.066666] ... max period: 0000007fffffffff
[ 0.066666] ... fixed-purpose events: 0
[ 0.066666] ... event mask: 000000000003ffff
[ 0.083426] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.090131] smpboot: Booting Node 0, Processors # 1 OK
[ 0.103307] Brought up 2 CPUs
[ 0.103313] smpboot: Total of 2 processors activated (11176.32 BogoMIPS)
[ 0.105254] devtmpfs: initialized
[ 0.109408] PM: Registering ACPI NVS region [mem 0x5fee0000-0x5fee2fff] (12288 bytes)
[ 0.110866] RTC time: 8:14:47, date: 02/01/14
[ 0.110947] NET: Registered protocol family 16
[ 0.111163] cpuidle: using governor ladder
[ 0.111167] cpuidle: using governor menu
[ 0.111208] ACPI: bus type PCI registered
[ 0.111213] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.111319] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.111324] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.135738] PCI: Using configuration type 1 for base access
[ 0.135903] mtrr: your CPUs had inconsistent fixed MTRR settings
[ 0.135906] mtrr: your CPUs had inconsistent variable MTRR settings
[ 0.135908] mtrr: probably your BIOS does not setup all CPUs.
[ 0.135909] mtrr: corrected configuration.
[ 0.136817] bio: create slab <bio-0> at 0
[ 0.136843] ACPI: Added _OSI(Module Device)
[ 0.136843] ACPI: Added _OSI(Processor Device)
[ 0.136843] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.136843] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.138901] ACPI: EC: Look up EC in DSDT
[ 0.147446] ACPI: SSDT 000000005fee9e40 00087 (v01 PmRef Cpu1Ist 00003000 INTL 20040311)
[ 0.147946] ACPI: Dynamic OEM Table Load:
[ 0.147951] ACPI: SSDT (null) 00087 (v01 PmRef Cpu1Ist 00003000 INTL 20040311)
[ 0.148273] ACPI: Interpreter enabled
[ 0.148286] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130725/hwxface-571)
[ 0.148294] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130725/hwxface-571)
[ 0.148318] ACPI: (supports S0 S3 S4 S5)
[ 0.148322] ACPI: Using IOAPIC for interrupt routing
[ 0.148365] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.148649] ACPI: No dock devices found.
[ 0.160204] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.160216] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.160220] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.160356] acpi PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.160362] acpi PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.160367] acpi PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.160371] acpi PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.160375] acpi PNP0A08:00: host bridge window [mem 0x5ff00000-0xfebfffff] (ignored)
[ 0.160379] PCI: root bus 00: using default resources
[ 0.160821] PCI host bridge to bus 0000:00
[ 0.160829] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.161397] pci 0000:00:00.2: [1106:2327] type 00 class 0x060000
[ 0.161635] pci 0000:00:00.3: [1106:3327] type 00 class 0x060000
[ 0.161871] pci 0000:00:00.4: [1106:4327] type 00 class 0x060000
[ 0.162115] pci 0000:00:00.5: [1106:5327] type 00 class 0x080020
[ 0.162387] pci 0000:00:00.6: [1106:6327] type 00 class 0x060000
[ 0.162628] pci 0000:00:00.7: [1106:7327] type 00 class 0x060000
[ 0.162869] pci 0000:00:01.0: [1106:b999] type 01 class 0x060400
[ 0.163124] pci 0000:00:02.0: [1106:a327] type 01 class 0x060400
[ 0.163236] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 0.163399] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 0.163475] pci 0000:00:03.0: [1106:c327] type 01 class 0x060400
[ 0.163602] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.163765] pci 0000:00:03.0: System wakeup disabled by ACPI
[ 0.163857] pci 0000:00:08.0: [1106:3044] type 00 class 0x0c0010
[ 0.163883] pci 0000:00:08.0: reg 0x10: [mem 0xdffff000-0xdffff7ff]
[ 0.163897] pci 0000:00:08.0: reg 0x14: [io 0xfc00-0xfc7f]
[ 0.163988] pci 0000:00:08.0: supports D2
[ 0.163992] pci 0000:00:08.0: PME# supported from D2 D3hot D3cold
[ 0.164200] pci 0000:00:0a.0: [13f6:0111] type 00 class 0x040100
[ 0.164226] pci 0000:00:0a.0: reg 0x10: [io 0xf800-0xf8ff]
[ 0.164326] pci 0000:00:0a.0: supports D1 D2
[ 0.164520] pci 0000:00:0f.0: [1106:0591] type 00 class 0x01018f
[ 0.164545] pci 0000:00:0f.0: reg 0x10: [io 0xf400-0xf407]
[ 0.164560] pci 0000:00:0f.0: reg 0x14: [io 0xf000-0xf003]
[ 0.164574] pci 0000:00:0f.0: reg 0x18: [io 0xec00-0xec07]
[ 0.164587] pci 0000:00:0f.0: reg 0x1c: [io 0xe800-0xe803]
[ 0.164601] pci 0000:00:0f.0: reg 0x20: [io 0xe400-0xe40f]
[ 0.164615] pci 0000:00:0f.0: reg 0x24: [io 0xe000-0xe0ff]
[ 0.164857] pci 0000:00:0f.1: [1106:0571] type 00 class 0x01018a
[ 0.164923] pci 0000:00:0f.1: reg 0x20: [io 0xdc00-0xdc0f]
[ 0.165186] pci 0000:00:10.0: [1106:3038] type 00 class 0x0c0300
[ 0.165250] pci 0000:00:10.0: reg 0x20: [io 0xd800-0xd81f]
[ 0.165308] pci 0000:00:10.0: supports D1 D2
[ 0.165311] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.165456] pci 0000:00:10.0: System wakeup disabled by ACPI
[ 0.165531] pci 0000:00:10.1: [1106:3038] type 00 class 0x0c0300
[ 0.165596] pci 0000:00:10.1: reg 0x20: [io 0xd400-0xd41f]
[ 0.165653] pci 0000:00:10.1: supports D1 D2
[ 0.165656] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.165803] pci 0000:00:10.1: System wakeup disabled by ACPI
[ 0.165873] pci 0000:00:10.2: [1106:3038] type 00 class 0x0c0300
[ 0.165937] pci 0000:00:10.2: reg 0x20: [io 0xd000-0xd01f]
[ 0.165995] pci 0000:00:10.2: supports D1 D2
[ 0.165998] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.166146] pci 0000:00:10.2: System wakeup disabled by ACPI
[ 0.166218] pci 0000:00:10.3: [1106:3038] type 00 class 0x0c0300
[ 0.166282] pci 0000:00:10.3: reg 0x20: [io 0xcc00-0xcc1f]
[ 0.166339] pci 0000:00:10.3: supports D1 D2
[ 0.166343] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.166497] pci 0000:00:10.3: System wakeup disabled by ACPI
[ 0.166567] pci 0000:00:10.4: [1106:3104] type 00 class 0x0c0320
[ 0.166592] pci 0000:00:10.4: reg 0x10: [mem 0xdfffe000-0xdfffe0ff]
[ 0.166691] pci 0000:00:10.4: supports D1 D2
[ 0.166695] pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.166839] pci 0000:00:10.4: System wakeup disabled by ACPI
[ 0.166918] pci 0000:00:11.0: [1106:3337] type 00 class 0x060100
[ 0.167234] pci 0000:00:11.7: [1106:287e] type 00 class 0x060000
[ 0.167490] pci 0000:00:12.0: [1106:3065] type 00 class 0x020000
[ 0.167515] pci 0000:00:12.0: reg 0x10: [io 0xc800-0xc8ff]
[ 0.167529] pci 0000:00:12.0: reg 0x14: [mem 0xdfffd000-0xdfffd0ff]
[ 0.168244] pci 0000:00:01.0: bridge window [io 0xa000-0xafff]
[ 0.168251] pci 0000:00:01.0: bridge window [mem 0xdfd00000-0xdfdfffff]
[ 0.168257] pci 0000:00:01.0: bridge window [mem 0xdfc00000-0xdfcfffff pref]
[ 0.168528] pci 0000:02:00.0: [10de:01dd] type 00 class 0x030000
[ 0.168547] pci 0000:02:00.0: reg 0x10: [mem 0xdc000000-0xdcffffff]
[ 0.168565] pci 0000:02:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.168583] pci 0000:02:00.0: reg 0x1c: [mem 0xdd000000-0xddffffff 64bit]
[ 0.168606] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 0.168753] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.168767] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.168773] pci 0000:00:02.0: bridge window [io 0x9000-0x9fff]
[ 0.168779] pci 0000:00:02.0: bridge window [mem 0xdc000000-0xdeffffff]
[ 0.168788] pci 0000:00:02.0: bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.169037] pci 0000:00:03.0: PCI bridge to [bus 03]
[ 0.169045] pci 0000:00:03.0: bridge window [io 0xb000-0xbfff]
[ 0.169052] pci 0000:00:03.0: bridge window [mem 0xdfb00000-0xdfbfffff]
[ 0.169062] pci 0000:00:03.0: bridge window [mem 0xdfe00000-0xdfefffff 64bit pref]
[ 0.169210] pci 0000:04:01.0: [1106:3288] type 00 class 0x040300
[ 0.169234] pci 0000:04:01.0: reg 0x10: [mem 0xdfafc000-0xdfafffff 64bit]
[ 0.169331] pci 0000:04:01.0: PME# supported from D0 D3hot D3cold
[ 0.169374] pci 0000:04:01.0: System wakeup disabled by ACPI
[ 0.169432] pci 0000:04:01.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.169487] pci 0000:00:13.0: PCI bridge to [bus 04]
[ 0.169493] pci 0000:00:13.0: bridge window [io 0x8000-0x8fff]
[ 0.169499] pci 0000:00:13.0: bridge window [mem 0xdfa00000-0xdfafffff]
[ 0.169508] pci 0000:00:13.0: bridge window [mem 0xdf900000-0xdf9fffff 64bit pref]
[ 0.170765] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
[ 0.170957] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
[ 0.171149] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
[ 0.171343] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5
[ 0.171497] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[ 0.171661] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0
[ 0.171808] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[ 0.171970] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *5
[ 0.172930] ACPI: Enabled 1 GPEs in block 10 to 1F
[ 0.172944] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.173038] Found 1 acpi root devices
[ 0.173158] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.173158] vgaarb: loaded
[ 0.173158] vgaarb: bridge control possible 0000:02:00.0
[ 0.173158] PCI: Using ACPI for IRQ routing
[ 0.184737] PCI: pci_cache_line_size set to 64 bytes
[ 0.184836] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
[ 0.184839] e820: reserve RAM buffer [mem 0x5fee0000-0x5fffffff]
[ 0.185030] NetLabel: Initializing
[ 0.185034] NetLabel: domain hash size = 128
[ 0.185036] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.185059] NetLabel: unlabeled traffic allowed by default
[ 0.185120] Switched to clocksource refined-jiffies
[ 0.195680] pnp: PnP ACPI init
[ 0.195708] ACPI: bus type PNP registered
[ 0.195924] system 00:00: [io 0x0400-0x047f] has been reserved
[ 0.195930] system 00:00: [io 0x0500-0x050f] has been reserved
[ 0.195937] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.196555] system 00:01: [mem 0xf0001000-0xf0001fff] has been reserved
[ 0.196562] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.196653] system 00:02: [mem 0xf0002000-0xf0002fff] has been reserved
[ 0.196660] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.196995] system 00:03: [mem 0xf0000000-0xf0000fff] has been reserved
[ 0.197002] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.197450] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.197455] system 00:04: [io 0x0290-0x0297] has been reserved
[ 0.197459] system 00:04: [io 0x0880-0x088f] has been reserved
[ 0.197464] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.197486] pnp 00:05: [dma 4]
[ 0.197536] pnp 00:05: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.197617] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.197674] pnp 00:07: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.197741] pnp 00:08: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.198390] pnp 00:09: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.198508] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.198515] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.198791] system 00:0b: [mem 0x000ce200-0x000cffff] has been reserved
[ 0.198796] system 00:0b: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.198800] system 00:0b: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.198804] system 00:0b: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.198808] system 00:0b: [mem 0x5fee0000-0x5fefffff] could not be reserved
[ 0.198812] system 00:0b: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.198816] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.198820] system 00:0b: [mem 0x00100000-0x5fedffff] could not be reserved
[ 0.198824] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.198828] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.198832] system 00:0b: [mem 0xfff80000-0xfffeffff] has been reserved
[ 0.198837] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.198848] pnp: PnP ACPI: found 12 devices
[ 0.198850] ACPI: bus type PNP unregistered
[ 0.207458] Switched to clocksource acpi_pm
[ 0.207509] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.207515] pci 0000:00:01.0: bridge window [io 0xa000-0xafff]
[ 0.207523] pci 0000:00:01.0: bridge window [mem 0xdfd00000-0xdfdfffff]
[ 0.207530] pci 0000:00:01.0: bridge window [mem 0xdfc00000-0xdfcfffff pref]
[ 0.207544] pci 0000:02:00.0: BAR 6: assigned [mem 0xde000000-0xde01ffff pref]
[ 0.207548] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.207554] pci 0000:00:02.0: bridge window [io 0x9000-0x9fff]
[ 0.207561] pci 0000:00:02.0: bridge window [mem 0xdc000000-0xdeffffff]
[ 0.207567] pci 0000:00:02.0: bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.207577] pci 0000:00:03.0: PCI bridge to [bus 03]
[ 0.207582] pci 0000:00:03.0: bridge window [io 0xb000-0xbfff]
[ 0.207590] pci 0000:00:03.0: bridge window [mem 0xdfb00000-0xdfbfffff]
[ 0.207596] pci 0000:00:03.0: bridge window [mem 0xdfe00000-0xdfefffff 64bit pref]
[ 0.207606] pci 0000:00:13.0: PCI bridge to [bus 04]
[ 0.207611] pci 0000:00:13.0: bridge window [io 0x8000-0x8fff]
[ 0.207619] pci 0000:00:13.0: bridge window [mem 0xdfa00000-0xdfafffff]
[ 0.207625] pci 0000:00:13.0: bridge window [mem 0xdf900000-0xdf9fffff 64bit pref]
[ 0.207634] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.207638] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
[ 0.207642] pci_bus 0000:01: resource 0 [io 0xa000-0xafff]
[ 0.207645] pci_bus 0000:01: resource 1 [mem 0xdfd00000-0xdfdfffff]
[ 0.207648] pci_bus 0000:01: resource 2 [mem 0xdfc00000-0xdfcfffff pref]
[ 0.207652] pci_bus 0000:02: resource 0 [io 0x9000-0x9fff]
[ 0.207655] pci_bus 0000:02: resource 1 [mem 0xdc000000-0xdeffffff]
[ 0.207659] pci_bus 0000:02: resource 2 [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.207662] pci_bus 0000:03: resource 0 [io 0xb000-0xbfff]
[ 0.207666] pci_bus 0000:03: resource 1 [mem 0xdfb00000-0xdfbfffff]
[ 0.207669] pci_bus 0000:03: resource 2 [mem 0xdfe00000-0xdfefffff 64bit pref]
[ 0.207673] pci_bus 0000:04: resource 0 [io 0x8000-0x8fff]
[ 0.207676] pci_bus 0000:04: resource 1 [mem 0xdfa00000-0xdfafffff]
[ 0.207679] pci_bus 0000:04: resource 2 [mem 0xdf900000-0xdf9fffff 64bit pref]
[ 0.207741] NET: Registered protocol family 2
[ 0.208099] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.208319] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.208486] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.208581] TCP: reno registered
[ 0.208594] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.208624] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.208735] NET: Registered protocol family 1
[ 0.208786] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.209588] pci 0000:02:00.0: Boot video device
[ 0.209597] PCI: CLS 4 bytes, default 64
[ 0.209685] Unpacking initramfs...
[ 0.304628] Freeing initrd memory: 3036K (ffff880037a02000 - ffff880037cf9000)
[ 0.304834] Scanning for low memory corruption every 60 seconds
[ 0.305383] audit: initializing netlink socket (disabled)
[ 0.305409] type=2000 audit(1391242487.303:1): initialized
[ 0.322282] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.324824] zbud: loaded
[ 0.325131] VFS: Disk quotas dquot_6.5.2
[ 0.325218] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.325540] msgmni has been set to 2996
[ 0.326126] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.326203] io scheduler noop registered
[ 0.326208] io scheduler deadline registered
[ 0.326278] io scheduler cfq registered (default)
[ 0.326706] pcieport 0000:00:02.0: irq 64 for MSI/MSI-X
[ 0.326982] pcieport 0000:00:03.0: irq 65 for MSI/MSI-X
[ 0.327123] ioapic: probe of 0000:00:00.5 failed with error -22
[ 0.327140] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.327169] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.327258] vesafb: mode is 640x480x32, linelength=2560, pages=0
[ 0.327262] vesafb: scrolling: redraw
[ 0.327265] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.327408] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc90010400000, using 1216k, total 1216k
[ 0.343291] Console: switching to colour frame buffer device 80x30
[ 0.359018] fb0: VESA VGA frame buffer device
[ 0.359078] GHES: HEST is not enabled!
[ 0.359194] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.359929] Linux agpgart interface v0.103
[ 0.360069] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.360073] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.360253] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.360472] mousedev: PS/2 mouse device common for all mice
[ 0.360603] rtc_cmos 00:06: RTC can wake from S4
[ 0.360821] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 0.360856] rtc_cmos 00:06: alarms up to one year, y3k, 242 bytes nvram
[ 0.360973] drop_monitor: Initializing network drop monitor service
[ 0.361073] TCP: cubic registered
[ 0.361298] NET: Registered protocol family 10
[ 0.361617] NET: Registered protocol family 17
[ 0.361632] Key type dns_resolver registered
[ 0.362117] registered taskstats version 1
[ 0.362862] Magic number: 2:64:219
[ 0.362974] rtc_cmos 00:06: setting system clock to 2014-02-01 08:14:48 UTC (1391242488)
[ 0.363051] PM: Hibernation image not present or could not be loaded.
[ 0.364957] Freeing unused kernel memory: 1144K (ffffffff818cb000 - ffffffff819e9000)
[ 0.364962] Write protecting the kernel read-only data: 8192k
[ 0.369593] Freeing unused kernel memory: 1012K (ffff880001503000 - ffff880001600000)
[ 0.371463] Freeing unused kernel memory: 420K (ffff880001797000 - ffff880001800000)
[ 0.380885] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.386910] systemd-udevd[47]: starting version 208
[ 0.445525] SCSI subsystem initialized
[ 0.461329] ACPI: bus type USB registered
[ 0.461417] usbcore: registered new interface driver usbfs
[ 0.461440] usbcore: registered new interface driver hub
[ 0.462121] libata version 3.00 loaded.
[ 0.462864] usbcore: registered new device driver usb
[ 0.464698] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.465272] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.465512] ehci-pci: EHCI PCI platform driver
[ 0.526805] firewire_ohci 0000:00:08.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[ 0.526880] pata_via 0000:00:0f.1: version 0.3.4
[ 0.528738] scsi0 : pata_via
[ 0.528910] scsi1 : pata_via
[ 0.529015] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xdc00 irq 14
[ 0.529019] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xdc08 irq 15
[ 0.529056] sata_via 0000:00:0f.0: version 2.6
[ 0.529269] sata_via 0000:00:0f.0: routed to hard irq line 11
[ 0.530888] scsi2 : sata_via
[ 0.531015] scsi3 : sata_via
[ 0.531085] ata3: SATA max UDMA/133 cmd 0xf400 ctl 0xf000 bmdma 0xe400 irq 21
[ 0.531089] ata4: SATA max UDMA/133 cmd 0xec00 ctl 0xe800 bmdma 0xe408 irq 21
[ 0.531315] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 0.531328] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 0.531400] uhci_hcd 0000:00:10.0: irq 20, io base 0x0000d800
[ 0.531711] hub 1-0:1.0: USB hub found
[ 0.531726] hub 1-0:1.0: 2 ports detected
[ 0.532106] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 0.532117] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 0.532157] uhci_hcd 0000:00:10.1: irq 22, io base 0x0000d400
[ 0.532422] hub 2-0:1.0: USB hub found
[ 0.532437] hub 2-0:1.0: 2 ports detected
[ 0.532771] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 0.532785] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 0.532838] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d000
[ 0.533101] hub 3-0:1.0: USB hub found
[ 0.533115] hub 3-0:1.0: 2 ports detected
[ 0.533501] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 0.533511] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 0.533551] uhci_hcd 0000:00:10.3: irq 23, io base 0x0000cc00
[ 0.533809] hub 4-0:1.0: USB hub found
[ 0.533824] hub 4-0:1.0: 2 ports detected
[ 0.534774] ehci-pci 0000:00:10.4: EHCI Host Controller
[ 0.534784] ehci-pci 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 0.534832] ehci-pci 0000:00:10.4: irq 21, io mem 0xdfffe000
[ 0.543378] ehci-pci 0000:00:10.4: USB 2.0 started, EHCI 1.00
[ 0.543662] hub 5-0:1.0: USB hub found
[ 0.543678] hub 5-0:1.0: 8 ports detected
[ 0.566765] hub 1-0:1.0: USB hub found
[ 0.566782] hub 1-0:1.0: 2 ports detected
[ 0.590105] hub 2-0:1.0: USB hub found
[ 0.590121] hub 2-0:1.0: 2 ports detected
[ 0.613435] hub 3-0:1.0: USB hub found
[ 0.613452] hub 3-0:1.0: 2 ports detected
[ 0.636783] hub 4-0:1.0: USB hub found
[ 0.636802] hub 4-0:1.0: 2 ports detected
[ 0.733360] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.867324] ata2.00: ATAPI: PHILIPS DVD8801, NW02, max UDMA/33
[ 0.880533] ata2.00: configured for UDMA/33
[ 0.884513] scsi 1:0:0:0: CD-ROM PHILIPS DVD8801 NW02 PQ: 0 ANSI: 5
[ 0.938113] ata3.00: ATA-7: ST3250820AS, 3.AAD, max UDMA/133
[ 0.938119] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.004743] ata3.00: configured for UDMA/133
[ 1.004864] scsi 2:0:0:0: Direct-Access ATA ST3250820AS 3.AA PQ: 0 ANSI: 5
[ 1.026833] firewire_core 0000:00:08.0: created device fw0: GUID 0010dc00010d6a99, S400
[ 1.206692] ata4: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 1.238301] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 1.238309] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.238691] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.239015] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.239111] sd 2:0:0:0: [sda] Write Protect is off
[ 1.239117] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.239158] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.287635] sda: sda1 sda2 sda3 sda4 sda5
[ 1.288484] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.306711] tsc: Refined TSC clocksource calibration: 2793.000 MHz
[ 1.723377] usb 3-2: new full-speed USB device number 2 using uhci_hcd
[ 1.886359] usb-storage 3-2:1.0: USB Mass Storage device detected
[ 1.886541] scsi4 : usb-storage 3-2:1.0
[ 1.886673] usbcore: registered new interface driver usb-storage
[ 2.090192] EXT4-fs (sda3): mounting ext3 file system using the ext4 subsystem
[ 2.106588] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.110265] usb 4-1: new full-speed USB device number 2 using uhci_hcd
[ 2.306777] Switched to clocksource tsc
[ 2.891527] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 2.894524] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 2.897522] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 2.900490] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 2.902787] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 2.903423] systemd[1]: Set hostname to <plaything>.
[ 2.945523] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 2.950494] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[ 2.955519] sd 4:0:0:2: [sdd] Attached SCSI removable disk
[ 2.960568] sd 4:0:0:3: [sde] Attached SCSI removable disk
[ 3.591733] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 3.592144] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 3.592244] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.592267] systemd[1]: Starting Remote File Systems.
[ 3.592290] systemd[1]: Reached target Remote File Systems.
[ 3.592308] systemd[1]: Starting LVM2 metadata daemon socket.
[ 3.592374] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 3.592391] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 3.592444] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 3.592461] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 3.592497] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 3.592514] systemd[1]: Starting Delayed Shutdown Socket.
[ 3.592552] systemd[1]: Listening on Delayed Shutdown Socket.
[ 3.592576] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 3.592645] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 3.592662] systemd[1]: Starting Paths.
[ 3.592680] systemd[1]: Reached target Paths.
[ 3.592696] systemd[1]: Starting Encrypted Volumes.
[ 3.592715] systemd[1]: Reached target Encrypted Volumes.
[ 3.592763] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 3.592939] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.592965] systemd[1]: Starting udev Kernel Socket.
[ 3.593003] systemd[1]: Listening on udev Kernel Socket.
[ 3.593023] systemd[1]: Starting udev Control Socket.
[ 3.593063] systemd[1]: Listening on udev Control Socket.
[ 3.593084] systemd[1]: Starting Journal Socket.
[ 3.593166] systemd[1]: Listening on Journal Socket.
[ 3.615844] systemd[1]: Started Set Up Additional Binary Formats.
[ 3.615867] systemd[1]: Starting udev Coldplug all Devices...
[ 3.617490] systemd[1]: Starting Apply Kernel Variables...
[ 3.619270] systemd[1]: Started Load Kernel Modules.
[ 3.619320] systemd[1]: Starting Setup Virtual Console...
[ 3.620083] systemd[1]: Mounting Huge Pages File System...
[ 3.620744] systemd[1]: Mounted FUSE Control File System.
[ 3.655735] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 3.656418] systemd[1]: Mounting POSIX Message Queue File System...
[ 3.657491] systemd[1]: Mounting Debug File System...
[ 3.658329] systemd[1]: Starting Journal Service...
[ 3.659162] systemd[1]: Started Journal Service.
[ 4.168803] systemd-journald[115]: Vacuuming done, freed 0 bytes
[ 4.317710] EXT4-fs (sda3): re-mounted. Opts: data=ordered
[ 4.587408] systemd-udevd[138]: starting version 208
[ 5.127819] ACPI: Requesting acpi_cpufreq
[ 5.335569] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 5.335582] ACPI: Power Button [PWRB]
[ 5.335669] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 5.335678] ACPI: Sleep Button [SLPB]
[ 5.335779] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.335787] ACPI: Power Button [PWRF]
[ 5.568863] thermal LNXTHERM:00: registered as thermal_zone0
[ 5.568869] ACPI: Thermal Zone [THRM] (40 C)
[ 5.822184] agpgart: Detected VIA P4M890 chipset
[ 5.830806] agpgart-via 0000:00:00.0: AGP aperture is 128M @ 0xd0000000
[ 5.887988] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.546795] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 6.546838] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[ 6.551408] via-rhine 0000:00:12.0 eth0: VIA Rhine II at 0x1c800, 00:19:db:37:46:0d, IRQ 23
[ 6.552220] via-rhine 0000:00:12.0 eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1
[ 6.619182] microcode: CPU0 sig=0xf64, pf=0x4, revision=0x4
[ 6.620850] pci 0000:00:13.0: setting latency timer to 64
[ 6.621044] snd_hda_intel 0000:04:01.0: irq 66 for MSI/MSI-X
[ 6.621102] snd_hda_intel 0000:04:01.0: PCI: Disallowing DAC for device
[ 6.661358] ACPI Warning: 0x0000000000000500-0x0000000000000507 SystemIO conflicts with Region \SM06 1 (20130725/utaddress-251)
[ 6.661372] ACPI Warning: 0x0000000000000500-0x0000000000000507 SystemIO conflicts with Region \SM05 2 (20130725/utaddress-251)
[ 6.661379] ACPI Warning: 0x0000000000000500-0x0000000000000507 SystemIO conflicts with Region \SM04 3 (20130725/utaddress-251)
[ 6.661385] ACPI Warning: 0x0000000000000500-0x0000000000000507 SystemIO conflicts with Region \SM03 4 (20130725/utaddress-251)
[ 6.661391] ACPI Warning: 0x0000000000000500-0x0000000000000507 SystemIO conflicts with Region \SM02 5 (20130725/utaddress-251)
[ 6.661397] ACPI Warning: 0x0000000000000500-0x0000000000000507 SystemIO conflicts with Region \SM00 6 (20130725/utaddress-251)
[ 6.661404] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 6.795628] [drm] Initialized drm 1.1.0 20060810
[ 6.801263] hidraw: raw HID events driver (C) Jiri Kosina
[ 6.829208] usbcore: registered new interface driver usbhid
[ 6.829216] usbhid: USB HID core driver
[ 6.835393] microcode: CPU1 sig=0xf64, pf=0x4, revision=0x4
[ 6.860307] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 6.904649] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/input/input5
[ 6.932606] input: HDA VIA VT82xx Front Headphone as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input13
[ 6.932897] input: HDA VIA VT82xx Line Out Side as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input12
[ 6.933135] input: HDA VIA VT82xx Line Out CLFE as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input11
[ 6.933566] input: HDA VIA VT82xx Line Out Surround as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input10
[ 6.933804] input: HDA VIA VT82xx Line Out Front as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input9
[ 6.934030] input: HDA VIA VT82xx Line as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input8
[ 6.934277] input: HDA VIA VT82xx Front Mic as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input7
[ 6.934506] input: HDA VIA VT82xx Rear Mic as /devices/pci0000:00/0000:00:13.0/0000:04:01.0/sound/card0/input6
[ 6.952171] input: Tempest Habu Mouse as /devices/pci0000:00/0000:00:10.3/usb4/4-1/4-1:1.0/input/input14
[ 6.956646] hid-generic 0003:1532:0009.0001: input,hidraw0: USB HID v10.01 Mouse [Tempest Habu Mouse] on usb-0000:00:10.3-1/input0
[ 6.959162] input: Tempest Habu Mouse as /devices/pci0000:00/0000:00:10.3/usb4/4-1/4-1:1.1/input/input15
[ 6.959476] hid-generic 0003:1532:0009.0002: input,hidraw1: USB HID v10.01 Keyboard [Tempest Habu Mouse] on usb-0000:00:10.3-1/input1
[ 7.031600] wmi: Mapper loaded
[ 7.080209] systemd-udevd[144]: renamed network interface eth0 to enp0s18
[ 7.437383] Adding 2097148k swap on /swapfile. Priority:-1 extents:27 across:3813440k FS
[ 7.629458] checking generic (c0000000 130000) vs hw (c0000000 10000000)
[ 7.629466] fb: conflicting fb hw usage nouveaufb vs VESA VGA - removing generic driver
[ 7.629495] Console: switching to colour dummy device 80x25
[ 7.630443] [drm] hdmi device not found 2 0 1
[ 7.630619] nouveau [ DEVICE][0000:02:00.0] BOOT0 : 0x046d00a3
[ 7.630624] nouveau [ DEVICE][0000:02:00.0] Chipset: G72 (NV46)
[ 7.630628] nouveau [ DEVICE][0000:02:00.0] Family : NV40
[ 7.632676] nouveau [ VBIOS][0000:02:00.0] checking PRAMIN for image...
[ 7.716068] nouveau [ VBIOS][0000:02:00.0] ... appears to be valid
[ 7.716075] nouveau [ VBIOS][0000:02:00.0] using image from PRAMIN
[ 7.716221] nouveau [ VBIOS][0000:02:00.0] BIT signature found
[ 7.716227] nouveau [ VBIOS][0000:02:00.0] version 8a.66.51.c3.34
[ 7.716307] nouveau W[ VBIOS][0000:02:00.0] unknown i2c type 64
[ 7.716312] nouveau W[ VBIOS][0000:02:00.0] unknown i2c type 64
[ 7.716331] nouveau W[ VBIOS][0000:02:00.0] 0xd250[ ]: unknown bits in register 0x40600858
[ 7.716348] nouveau W[ VBIOS][0000:02:00.0] 0xd2b0[ ]: unknown bits in register 0x40101000
[ 7.716355] nouveau W[ VBIOS][0000:02:00.0] 0xd319[ ]: unknown bits in register 0x03594e04
[ 7.716362] nouveau W[ VBIOS][0000:02:00.0] 0xd3b4[ ]: unknown bits in register 0x40682608
[ 7.716367] nouveau W[ VBIOS][0000:02:00.0] 0xd3f0[ ]: unknown bits in register 0x40100220
[ 7.716373] nouveau E[ VBIOS][0000:02:00.0] 0xd510[ ]: unknown opcode 0x14
[ 7.716424] nouveau [ PFB][0000:02:00.0] RAM type: DDR2
[ 7.716428] nouveau [ PFB][0000:02:00.0] RAM size: 128 MiB
[ 7.716432] nouveau [ PFB][0000:02:00.0] ZCOMP: 0 tags
[ 7.733640] nouveau [ PTHERM][0000:02:00.0] FAN control: none / external
[ 7.733664] nouveau [ PTHERM][0000:02:00.0] fan management: disabled
[ 7.733670] nouveau [ PTHERM][0000:02:00.0] internal sensor: no
[ 7.753883] nouveau 0000:02:00.0: PCI: Disallowing DAC for device
[ 7.754021] [TTM] Zone kernel: Available graphics memory: 768516 kiB
[ 7.754025] [TTM] Initializing pool allocator
[ 7.754034] [TTM] Initializing DMA pool allocator
[ 7.754055] nouveau [ DRM] VRAM: 124 MiB
[ 7.754061] nouveau [ DRM] GART: 512 MiB
[ 7.754067] nouveau W[ DRM] DAC load detection comparison table version 9.5 not known
[ 7.754079] [TTM] Finalizing pool allocator
[ 7.754087] [TTM] Finalizing DMA pool allocator
[ 7.754150] [TTM] Zone kernel: Used memory at exit: 0 kiB
[ 8.676606] EXT4-fs (sda4): mounting ext3 file system using the ext4 subsystem
[ 8.678259] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: data=ordered
[ 8.794000] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: data=ordered
[ 9.118951] EXT4-fs (sda5): mounting ext3 file system using the ext4 subsystem
[ 9.173867] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: data=ordered
[ 9.243828] systemd-journald[115]: Received request to flush runtime journal from PID 1

Similar Messages

  • Problem with JFrame and busy/wait Cursor

    Hi -- I'm trying to set a JFrame's cursor to be the busy cursor,
    for the duration of some operation (usually just a few seconds).
    I can get it to work in some situations, but not others.
    Timing does seem to be an issue.
    There are thousands of posts on the BugParade, but
    in general Sun indicates this is not a bug. I just need
    a work-around.
    I've written a test program below to demonstrate the problem.
    I have the problem on Solaris, running with both J2SE 1.3 and 1.4.
    I have not tested on Windows yet.
    When you run the following code, three JFrames will be opened,
    each with the same 5 buttons. The first "F1" listens to its own
    buttons, and works fine. The other two (F2 and F3) listen
    to each other's buttons.
    The "BUSY" button simply sets the cursor on its listener
    to the busy cursor. The "DONE" button sets it to the
    default cursor. These work fine.
    The "SLEEP" button sets the cursor, sleeps for 3 seconds,
    and sets it back. This does not work.
    The "INVOKE LATER" button does the same thing,
    except is uses invokeLater to sleep and set the
    cursor back. This also does not work.
    The "DELAY" button sleeps for 3 seconds (giving you
    time to move the mouse into the other (listerner's)
    window, and then it behaves just like the "SLEEP"
    button. This works.
    Any ideas would be appreciated, thanks.
    -J
    import java.awt.BorderLayout;
    import java.awt.Cursor;
    import java.awt.event.ActionEvent;
    import java.awt.event.ActionListener;
    import javax.swing.JButton;
    import javax.swing.JFrame;
    import javax.swing.JPanel;
    import javax.swing.SwingUtilities;
    public class BusyFrameTest implements ActionListener
    private static Cursor busy = Cursor.getPredefinedCursor (Cursor.WAIT_CURSOR);
    private static Cursor done = Cursor.getDefaultCursor();
    JFrame frame;
    JButton[] buttons;
    public BusyFrameTest (String title)
    frame = new JFrame (title);
    buttons = new JButton[5];
    buttons[0] = new JButton ("BUSY");
    buttons[1] = new JButton ("DONE");
    buttons[2] = new JButton ("SLEEP");
    buttons[3] = new JButton ("INVOKE LATER");
    buttons[4] = new JButton ("DELAY");
    JPanel buttonPanel = new JPanel();
    for (int i = 0; i < buttons.length; i++)
    buttonPanel.add (buttons);
    frame.getContentPane().add (buttonPanel);
    frame.pack();
    frame.setVisible (true);
    public void addListeners (ActionListener listener)
    for (int i = 0; i < buttons.length; i++)
    buttons[i].addActionListener (listener);
    public void actionPerformed (ActionEvent e)
    System.out.print (frame.getTitle() + ": " + e.getActionCommand());
    if (e.getActionCommand().equals ("BUSY"))
    frame.setCursor (busy);
    else if (e.getActionCommand().equals ("DONE"))
    frame.setCursor (done);
    else if (e.getActionCommand().equals ("SLEEP"))
    frame.setCursor (busy);
    try { Thread.sleep (3000); } catch (Exception ex) { }
    frame.setCursor (done);
    System.out.print (" finished");
    else if (e.getActionCommand().equals ("INVOKE LATER"))
    frame.setCursor (busy);
    SwingUtilities.invokeLater (thread);
    else if (e.getActionCommand().equals ("DELAY"))
    try { Thread.sleep (3000); } catch (Exception ex) { }
    frame.setCursor (busy);
    try { Thread.sleep (3000); } catch (Exception ex) { }
    frame.setCursor (done);
    System.out.print (" finished");
    System.out.println();
    Runnable thread = new Runnable()
    public void run()
    try { Thread.sleep (3000); } catch (Exception ex) { }
    frame.setCursor (done);
    System.out.println (" finished");
    public static void main (String[] args)
    BusyFrameTest f1 = new BusyFrameTest ("F1");
    f1.addListeners (f1);
    BusyFrameTest f2 = new BusyFrameTest ("F2");
    BusyFrameTest f3 = new BusyFrameTest ("F3");
    f2.addListeners (f3); // 2 listens to 3
    f3.addListeners (f2); // 3 listens to 2

    I've had the same problems with cursors and repaints in a swing application, and I was thinking of if I could use invokeLater, but I never got that far with it.
    I still believe you would need a thread for the time consuming task, and that invokeLater is something you only need to use in a thread different from the event thread.

  • Problem with installing and running some applications or drivers

    When installing and installing some items, towards the end of the installation I get this message:
    /System/Library/Extensions/comcy_driver_USBDevice.kext
    *was installed improperly and cannot be used. Please try reinstalling it or contact product's vendor for update*
    The end result is that some things do not seem to work properly, such as my HP printer. Would anybody have any ideas on how to fix this problem?

    Thank you for your response. Originally, I had a problem with Airport and ended up reinstalling Snow Leopard. Since then, when downloading upgrades etc, such as HP printer drivers, iTunes etc., towards the end of the download when its running the script, I get this message: /System/Library/Extensions/comcy_driver_USBDevice.kext
    +was installed improperly and cannot be used. Please try reinstalling it or contact product's vendor for update+
    Sometimes, the download hangs and is unable to complete. The main problem I've encountered so far with an application is when I use the printer to scan an image via Preview, it's blank: there's nothing there.

  • Problems with outlook and address book contacts: my outlook contacts had around 3,000 entries. Outlook duplicated by itself and now outlook and address book have each over 340,000. What should I do?

    Problems with outlook and address book contacts: my outlook contacts had around 3,000 entries. Outlook duplicated entries and have now 340,000. I reinstalled microsoft office and, thus, outlook, and reinstalled mac OS X system and applications. While I managed to delete outlook contacts so that I can re-sync with my blackberry, the contacts at Mac Address Book were not deleted and still have over 340,000 entries. I do not mind deleting all contacts since I have back up, but I have not been able to delete them. Also, when I go at Address Book and try to delete or merge duplicated entries, the system takes forever and never ends because of such large amount of entries. Worse, when I do so I run out of RAM memory.
    My Macbook pro is just 2 months old.
    What should I do? Is there a way to delete my Mac Address Book without having the problem above?
    Many thanks
    Regis

    zlatan24 wrote:
    For solving out troubles connected with corrupted or lost address book you may use address book recovery. It owns various features such as restoring wab files, it working under any Windows OS. The utility has modern and easy to use interface due to almost every experienced users.
    If it is a windows problem it's not going to run on the OP's MacBook Pro

  • Problems with Safari and Firefox (HTTP?)

    Problems with Safari and Firefox (HTTP?)
    On a laptop G4, 10.5.8 and Safari 5.02 I experience the following:
    On the account of my oldest daughter everything works fine, i.e. wireless internet works and no problems with mail or safari.
    On the same laptop, on the account of my other daughter, the wireless is OK, she can mail etc. But safari nor firefox works. It says: can’t find server (whatever site) and in the activity window it looks if safari tries to open files (in the safari preferences-folder) in stead of http. Same applies to Firefox, so maybe it has more to do with HTTP in general?
    What goes wrong? What to do? I tried the following on the host terminal (tips from Apple)
    defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false
    and
    defaults delete com.apple.safari WebKitDNSPrefetchingEnabled
    but that did not help,
    Nanne

    I'm still wondering why it happens now at this moment in time...
    PC does seem to be a bit odd & inconsistent, the few times I've tested with it, at least so far as we content filtering goes; and if I remember rightly, you're not the first to report previously ok settings suddenly preventing some or all internet until pc is switched off altogether.
    It may work when re-enabled

  • Haven't been able to use pages for a while.  Keep getting following message.  Have tried reinstalling iWork, but no luck.  Same problems with Keynote and Numbers/Users/scottmcdonald/Desktop/Screen Shot 2012-03-14 at 9.39.52 PM.png

    Haven't been able to use pages for a while.  Keep getting following message.  Have tried reinstalling iWork, but no luck.  Same problems with Keynote and Numbers/

    Have you moved Pages from its installed location? Or just dragged a copy to your current system?
    It can't find some of its resources apparently.
    Peter

  • Problem with DMGs and error: "No Mountable File Systems"

    Problem with DMGs and error: "No Mountable File Systems"
    The files are not corrupt. The problem is occurring with all DMGs that are apparently formatted in MS-DOS FAT16. No the file will not mount with Disk utility or any other disk mounter programs I have found.
    This is now the second time this occurred and now effects my MBP and my iMac. First time i spent days with Apple support and the only solution was ultimately back up the data, reformat the HD, start over from scratch and reload everything. That lasted about a month before the problem resurfaced and is now an issue on both iMac and MBP.
    I tried to identify all the programs I installed immediately before the error, as I am convinced it is the result of a software conflict.
    Recent programs includes:
    1) upgrading from Parallels 5.5 to 6.0 on both machines.
    2) using an HP secure II usb drive and setting up a secure disk.
    3) installing new itunes 10
    4) new update to Flip For Mac.
    The files affected are downloaded dmgs, including personal brain and google earth, both which are formatted in FAT16.
    Any help or thoughts? Apple has now spent hours trying and they say i now have to reformat and wipe and start over. That is unacceptable and based on pasted experience the problem is likely to repeat itself. having to wipe and rebuild a HD ever month is not an solution. i need to fid the root problem.
    In the meantime, anyone got a real solution on how to extract the data for a DMG using a different method?
    Message was edited by: remaia

    Where you able to find the solution, i am having the same problem, all was fine till i install some programs only same one i saw did we both did was flip4mac i uninstalled it but the problem is still there, i also restored and erased the hardrive but im not up to doing that all over again. If you found anything out let me know i would greatly appreciate it

  • Problem with Send and Receive Emal In SAP System

    Hi gurus!
    I have a following quote:
    Dear !
    I have a problem with send and receive email in SAP system following :
    I want to test send and receive email in local network at my company. I
    had two server
    Server 1 : I setup Exchange Mail Server 2007 with domain controller is
    fes.com
    Server 2 : I setup SAP ERP ECC 6.0
    On Server 1 : I created 2 account ( u1Afes.com and u2Afes.com ) and then I tested send and receive email between u1 and u2 in local network through Microsoft Outlook 2007 -> OK
    and then
    On Server 2: I had configured send and receive email on SAP system
    through tcode SBWP, SCOT and SOST as Note 455140 - "Configuration of
    e-mail, fax, paging or SMS using SMTP"
    for example :
    I logged in SAP system with user Basis01 (with email u1Afes.com ) -> then,using tcode SBWP -> new message -> send to u2Afes.com with Internet Mail type and then status message with green light -> sending ok
    and then I have used Microsoft Outlook 2007, I logged with account u2 ->check email -> Ok. I saw message which send from u1
    Finally, My problem is how can receive mail in SAP system without using Microsoft Outlook
    For example:
    Login system SAP with Basis01 account (with  u1Afes.com ) -> tcode SBWP ->New Message -> send to u2Afes.com
    and then
    Login system SAP with Basis02 account (with u2Afes.com ) -> tcode ??? ->
    To receive email from Basis01 (with u1Afes.com )
    Please help me now
    Thanks
    I replace "@" with "A" because of banning email of this forum.
    This quote is about sending email in local network. And we can't receive any email from the outside email address. Addition if I wanna send email to internal email in Internet (we've just tried with email address in local network) What should I config in SAP and Exchange ?
    By the way, Is SAP Server IP added to Relay Agent for sending or receiving mail ?
    Regards
    An NLP
    Edited by: An NLP on Apr 6, 2010 7:03 PM

    Hi,
    This problem is a classic problem of mail routing via Exchange. Exchange like most mail servers use the domain part of the email address as a means to route mails. So I will make an assumption that your main company mail addrss is "User @ fes.com".
    So when you send a mail to the "User @ fes.com mail" address the mail is delivered to your Outlook mail address as this is the default route for company.
    (Q) So how do you get your Exchange server to relay the mail into the sending SAP system?
    (A) The easiest way would be to setup and unique mail domain for your SAP system. I always recommend "user @ client.sid.company.com" which in your case would be "u1 @ 100.PRD.fes.com". You can then instruct Exchange to send any emails addressed to 100.PRD.fes.com domain to your SAP system. Also using this format of address you can configure multiple mail connections into multiple SAP systems.
    (A) Another answer would be to enter the "Full" email address (LOcal and Domain part of address) into the routing rule for Exchange e.g. "U1 @ fes.com" so that all emails addressed to this user will be delivered into SAP. However this method requires a lot of Admin as you will have to update Exchange with ALL email address that need to receive emails. Also if your corporate mail address is "U1 @ fes.com" then all mails will be forwarded to SAP.
    I would definitely NOT recommend this method but the decision is up to you.
    P.S. The IP address of the SAP system is entered into the mail header of the email. This is standard practice in SMTP relay. You can suppress this header in Exchange
    Hope this helps
    Michael

  • Problem with Speaker and Headset in Windows Vista

    Hi, I just got my Macbook Pro 13" and having problem with speaker and headset when working with Windows Vista (I have installed the driver from bootcamp). The sound very weak if I play music from Itunes or youtube even the volume already full and if i put my headset the sound not coming out. Is there anyone can help me to solve this problem?
    Regards,Edwin

    When you post about Windows / Boot Camp, in Mac Pro (workstation) forum where others with a MacBOOK would be more likely to have same hardware configuration, and you won't find Windows drivers on Apple downloads. More like at
    http://www.guru3d.com or other sites, or go to RealTek (if that is the type of audio you have).

  • Problem with trigger and entity in JHeadsart, JBO-25019

    Hi to all,
    I am using JDeveloper 10.1.2 and developing an application using ADF Business Components and JheadStart 10.1.2.27
    I have a problem with trigger and entity in JHeadsart
    I have 3 entity and 3 views
    DsitTelephoneView based on DsitTelephone entity based on DSIT_TELEPHONE database table.
    TelUoView based on TelUo entity based on TEL_UO database table.
    NewAnnuaireView based on NewAnnuaire entity based on NEW_ANNUAIRE database view.
    I am using JHS to create :
    A JHS table-form based on DsitTelephoneView
    A JHS table based on TelUoView
    A JHS table based on NewAnnuaireView
    LIB_POSTE is a :
    DSIT_TELEPHONE column
    TEL_UO column
    NEW_ANNUAIRE column
    NEW_ANNUAIRE database view is built from DSIT_TELEPHONE database table.
    Lib_poste is an updatable attribut in TelUo entity, DsitTelephone entity, NewAnnuaire entity.
    Lib_poste is upadated in JHS table based on TelUoView
    I added a trigger on my database shema « IAN » to upadate LIB_POSTE in DSIT_TELEPHONE database table :
    CREATE OR REPLACES TRIGGER “IAN”.TEL_UO_UPDATE_LIB_POSTE
    AFTER INSERT OR UPDATE OFF lib_poste ONE IAN.TEL_UO
    FOR EACH ROW
    BEGIN
    UPDATE DSIT_TELEPHONE T
    SET t.lib_poste = :new.lib_poste
    WHERE t.id_tel = :new.id_tel;
    END;
    When I change the lib_poste with the application :
    - the lib_poste in DSIT_TELEPHONE database table is correctly updated by trigger.
    - but in JHS table-form based on DsitTelephoneView the lib_poste is not updated. If I do a quicksearch it is updated.
    - in JHS table based on NewAnnuaireView the lib_poste is not updated. if I do a quicksearch, I have an error:
    oracle.jbo.RowAlreadyDeletedException: JBO-25019: The row of entity of the key oracle.jbo. Key [null 25588] is not found in NewAnnuaire.
    25588 is the primary key off row in NEW_ANNUAIRE whose lib_poste was updated by the trigger.
    It is as if it had lost the bond with the row in the entity.
    Could you help me please ?
    Regards
    Laurent

    The following example should help.
    SQL> create sequence workorders_seq
      2  start with 1
      3  increment by 1
      4  nocycle
      5  nocache;
    Sequence created.
    SQL> create table workorders(workorder_id number,
      2  description varchar2(30),
      3   created_date date default sysdate);
    Table created.
    SQL> CREATE OR REPLACE TRIGGER TIMESTAMP_CREATED
      2  BEFORE INSERT ON workorders
      3  FOR EACH ROW
      4  BEGIN
      5  SELECT workorders_seq.nextval
      6    INTO :new.workorder_id
      7    FROM dual;
      8  END;
      9  /
    Trigger created.
    SQL> ALTER SESSION SET NLS_DATE_FORMAT = 'DD-MON-YYYY HH24:MI:SS';
    Session altered.
    SQL> insert into workorders(description) values('test1');
    1 row created.
    SQL> insert into workorders(description) values('test2');
    1 row created.
    SQL> select * from workorders;
    WORKORDER_ID DESCRIPTION                    CREATED_DATE
               1 test1                          30-NOV-2004 15:30:34
               2 test2                          30-NOV-2004 15:30:42
    2 rows selected.

  • Problem with ADS and LDAP

    Problem with ADS and LDAP
    I have installed Win2000 + sp1 and ADS on a computer. This computer is PDC.
    After connection via LDAP I cann't get any object ( users or goups etc. ).
    I try connect to ADS by java ( JNDI ).
    When I use another clients of LDAP ( eg. Maxware Directory Explorer) I have
    the same problem - no objects.
    Can anybody help me?
    Grzegorz Pszona
    my e-mail: [email protected]

    Thanks a lot.
    Softerra's browser is really good.
    Thanks
    Rashmi
    "Anant Kadiyala" <[email protected]> wrote:
    >
    I used Softerra's LDAP browser. The browser is free. There is also a
    java baded
    LDAP browser from Univ of Michigan. I found the Softerra browser to be
    more easier
    to use.
    -anant
    "rashmi" <[email protected]> wrote:
    Hi,
    Can you please let me know which exact ADS tool that you used to examine
    the
    DN. I have Active Directory Users and Computers, Sites and Servicesand
    Domain
    and Trusts installed on my machine but I am not able to figure out how
    to get
    the DN?
    Thanks
    Rashmi
    for Stephen Davies <[email protected]> wrote:
    Grzegorz,
    I have had WLS6.1 & ADS working ok using LDAP V2. Mind you it did take
    a
    fair bit of messing around to get it going. MS does have a few oddities,
    for example the Administrators DN might look something like this:
    cn=Administrator,cn=Users,dc=eglobal,dc=net
    One tool that I found invaluable came with the additional support tools
    for Windows 2000. The 'Active Directory Administration Tool' made it
    easy to list the directory contents and examine the DNs.
    Regards,
    Steve
    Stephen Davies
    Principal Consultant
    eGlobal Services Pty. Ltd.
    Sydney, Australia
    Ph. +61 2 9283 1033
    http://www.eglobal.net/

  • Problem with Rescue and Recovery after installing Norton Internet Security 2010

    Hi all.
    It's my first time in this forum.
    I have a problem, with Rescue and Recovery, after installing Norton Internet Security 2010 on my T43.
    The message I get it:
    "Rescue and Recovery is unable to back up the file 'C:\Documents and settings\all Users\Application Data\ Norton\ 00000082\00000109\000003c1\cltMLS1.bat' Because the file is either corrupted or being used by another application. Please close any application that could be using the file.
    I tried to close the Norton but I couldn't find how.
    Tanks
    Doron71

    Hi and welcome to the forum,
    the reason for this situation is, that the antivir files are protected from being modified.
    This is the reason, why this file cannot be backed up. I assume, that you would get much more such messages, as there are surelly multiple files files, that are protected like this.
    So the solution is to block folders from being archived. Please start RnR application and in the configuration set this folder as the excluded one.
    This will skip the backup of this file and will fix your situation.
    Please let me know, if you have covered this.
    Cheers

  • Problem with dreamweaver and Flash

    Hi, maybe someone can help me, i have any problem with
    dreamweaver and flash, i have a page and i have a menu and
    sub-menu, and the same page i have a category en flash 550 x 700 (
    photography and more... ) but when the menu to unfold
    the menu to see under flash and it cant see ( sorry my
    english is bad.... i hope you can understand me, and help me.. )
    i dont now why always flash ever stay up, or first, and
    another information under flash... this a problem... if you have
    menus...
    thanks.... have nice day.....

    This is a drawback of using flash or any other active
    content. By default, all active content including flash will
    display over every other content and thats why your menu stays
    under the flash movie. Some people make the flash background
    transparent to show content under the flash movie, but that will
    not work for menu items.
    I would suggest that you make the menu such that it does not
    overlap with the flash movie.

  • Problem with Preview and PSD files - random gray square

    Hi guys, hope you can help...
    I've got a problem with Preview and PSD files.
    If I open in Preview both an original jpg straight from my reflex and the photoshop version of the same picture, the psd file presents a gray square (of what it seems unrendered image) in a random area of the photo (sometimes in the center.). The square is quite big...
    If I zoom in or zoom out it disappears...if I scroll to another photo and then back to the psd, the square it's there again...sometimes in a different position.
    I've tried the same psd on my older iMac with leopard...and got no problem at all.
    I suspect it got something to do with my Ati...
    (this is the second iMac 27...the first went back for gray banding on the lcd screen and flickering and yellow tinge........)
    Thanks for your help.
    DAve.

    maybe I'm onto something...
    I've just found out that opening Preview in 32bit mode (instead of default 64bit) works flawlessly with any psd files. If I switch back to 64bit mode, Preview is much faster but the gray square comes back...
    It seems like the i7 is much faster than the Ati....
    Any more realistic ideas?

  • Problem with ECS and XSD

    Hi B2B Gurus,
    We are facing the problem with ECS and XSD files from past 2 weeks, Steps we followed
    1. Created a ECS file in document editor version 11g: 6.6.0
    2. ECS files consists only from ST and SE segments
    Ex: ST
    BCH
    CUR
    REF
    PER -- Exclude
    TAX -- Exclude
    SE
    3: Generated a XSD file from ECS file( File --> export---> Oracle B2B) in document ediotr
    4. We imported a ECS and XSD file in B2B console( documents---docdef-transaction set ECS file) and XSD File
    5. We tested one file from manually we face below error:
    Error Code B2B-51507
    Error Description Machine Info: (usmtnz-dinfap19.dev.emrsn.org) Description: Payload validation error.
    Error Level ERROR_LEVEL_COLLABORATION
    Error Severity ERROR
    Error Text
    and some times it shows Guideline load Error or simply Error
    Please help us to resolve this
    Regards

    Anuj,
    We are sending the EDI XML file from backend, then B2B will convert it into EDI file, How can we analyze EDI XML file with ECS file, B2B is not converting to EDI.
    1. Can we use 10g ECS file and XSD file in 11G
    2. I tried to import it, but it showing below error while doing testing
    App Message property     {MSG_ID=90422086, Sequencing=false, DOCTYPE_REVISION=5020, MSG_TYPE=1, FROM_PARTY=EMERSON, DOCTYPE_NAME=850, TO_PARTY=APLL, ATTACHMENT=}
    Direction     OUTBOUND
    State     MSG_ERROR
    Error Code     B2B-51507
    Error Text     Error Brief : The element does not include any significant data.
    Error Description     Error : The Element PER02 does not include any significant data characters. Segment PER is defined in the guideline at position 3600.{br}{br}This error was detected at:{br}{tab}Segment Count: 11{br}{tab}Element Count: 2{br}{tab}Characters: 5395 through 5397
    Created Date     06/20/2011 02:52 PM
    Modified Date     06/20/2011 02:52 PM
    Note: I used the same files in 10G its working fine.
    Regards
    Edited by: Francis on Jun 20, 2011 10:48 AM

Maybe you are looking for