Problems With Office Network

At my office they just expanded to take over the second half of our building and put doors in, etc. This got me moved to nice, big, quiet office in the new section.
Naturally, someone ran the ethernet cables over to the new offices. Now I can no longer connect to the other Mac in the old office. On my Mac nothing from the old side of the building shows up in Network in the Finder. The other Mac cannot see me but still can see all the other computers on that side.
I can find computers hooked up on this side but not the other. If I put in the other Mac's IP address I can connect, but this is a hassle because we can't use static addresses, so I have to go look up his address from time to time. But he cannot connect to me using my IP address.
With the move I did notice that my router address changed completely so that all the IP addresses on this side of the building are very different from the other side. I don't know enough about networks to know why this is so, I should still be on the same network as the rest the office, only one router into the building as far as I know.
The weird part is that I can connect to the other Mac using the IP address, so that means my computer can see his, even though he can't see me and our Macs don't show up in the Network in Finder.
What's going on and is there a simple way to get one of us to show up in the Finder Network so I don't have to keep getting his IP address.

Looks like you may have to open certain ports that might be required by WECM.
Couldn't really find too much, but from what I did manage to find, it looks like 2948 is the port you need to forward to your laptop.
Before you do that though, are you on the latest firmware for the E4200?
Just to ensure that there isn't anything else that may be the problem, it's always recommended to be at the latest firmware. Also, before forwarding the port, you could try adjusting the MTU a little as well. Reduce it to around 1472 bytes, and keep going down to around 1365 bytes by decreasing the value by 20 bytes each time. It may well just be an MTU issue rather than the ports. In either case, please do post back if your issue is resolved with any of the above suggestions.

Similar Messages

Ios6.0.1 = Problem with office network desktop computers

Hi,
We have a few iPhones connected onto our office computer network via a WIFI router.
While those iPhones were running IOS 5, we had no issues.
Now, since IOS 6 - and even IOS 6.0.1 is running on those iPhones, I have 2 iPhones causing network issues to DESKTOP COMPUTERS when connected to the office network through WIFI.
Basically, when those iPhones are connected to our network via WIFI, always the same 2 desktop computers then have network connectivity issues.
Those computers have the following IP address:
Computer A: 192.168.1.92
Computer B: 192.168.1.103
When let's say iPhone A is connected to the WIFI router, then Computer A starts to have network issue - ping does not work anymore - or only randomly - user cannot printed - computer cannot connect to Windows Shares anymore.
I have found about that by changing the IP address of the computer the problem was then solved.
I have then check the IP address used by the iPhone A ... it is not the original one used by the Computer A ... It is a different IP address provided by our DHCP server ... so the problem is not there (?).
I then ran an nmap request on 192.168.1.92 while Computer A had issue ...and found on that the MAC ADDRESS reported was not the one of Computer A - but the one of iPhone A !!!
So, when iPhone A connects to the network via WIFI - it seems to confuse the switches despites not having the same IP address ...
If I ask my collegue to switch the WIFI off on his iPhone, then the problem disappear straight away ... No more issue with the computer and its IP address 192.168.1.92 ... and nmap then reports the correct computer MAC ADDRESS.
The same problem happens with Computer B and iPhone B ...
We have RESET NETWORK settings on both iPhones but this did now solved the issue.
Can someone help out ?
Thanks & regards
GL

I'd say the scope of your dhcp server is probably overlapping your fixed ip addresses on your desktops
Could be due to the lease time the reason your not seeing the ip addresses on the devices you expect
Could also be a rouge dhcp server somewhere

Time Machine and "might be a problem with your network"

Hi! My Power Mac is from 2008, and I'm in the middle of replacing my hard drive. Here's a summary of what I've gone through, including various trouble shooting...
OK, the hard drive dies (all of which I wrote about in an earlier thread and, I think, not very relevant for this thread). While waiting to buy my replacement, I created an external bootable drive, hooked up via FW800. I created a new User Account, and then I used the Migration Assistant to bring in all the user settings, files, etc, from my Time Machine. It took many hours and and during the stage when it was transferring files, it gave me the prompt: "There might be a problem with your network. The other Mac is not responding. Make sure that all of your network devices are connected and turned on. Also, make sure that your Ethernet cables are still connected properly to your computer and to the network, or if using AirPort, that the base station is in range and turned on." After clicking "Continue" got me nowhere, I clicked Cancel, and it was a very incomplete migration [no apps, no files]. I didn't sweat this since this external drive is a temporary solution anyway.
Tonight I came home with the new internal drive, installed it, installed Leopard, and began the Setup Assistant. I got the same prompt as last night. NOTE: This time with Setup Assistant; last night was with Migration Assistant.
I notice from reviewing the boards that this Time Machine glitch seemed to happen a few years ago, in Leopard, and maybe hasn't happened since. But I haven't read a thread with a solution. (Maybe I missed it?)
A few things come to mind:
1. Could there be an issue with the fact that the computer is only 10.5 and many of the files/apps may have been installed when I was running 10.5.8? I'm just tossing that out there. For instance, what if I set up an initial User account, then updated the software to 10.5 and THEN used Migration Assistant to bring in the older account?
2. Soon, since I'm reinstalling Leopard, I'll get the prompt to use Setup Assistant, and this time I'll just select account settings and apps. I'll bring in the files manually, later. Since the progress window seems to get hung up during the file-transferring stage, maybe I'll have better luck if I skip that.
If anyone has any suggestions, man, I'd be way grateful!
Thanks!

"try trashing the timemachine.plist in your original user's Library>Preferences."
I didn't even get to that step. Here's what happened.
I went back to my original Admin account (the one I restored via Setup Assistant, from my Time Machine backup), and ran Migration Assistant again. I selected Applications only and when it gave me a prompt about the account name already existing. So, I created a new account name (TEMP 1, I called it).
All of my applications were restored.
Next, I tried it with all the files and folders. It didn't give me the duplicate name prompt this time. It copied all my flles and folders over.
Was it perfect? Well, a lot of the apps need some fresh registration and some upgrading, but I suppose that's to be expected. Or is it?
While I feel like this problem is in my rear-view mirror, I'm still interested in your suggestons for a Time Machine altenative.
Thanks again for your advice!

I cant connect with my imessage and facetime in my iphone; i already upload de i os 7.02 but the message still have it; it said that they have problem with the network; i reset the network and doesnt work

I cant connect with my imessage and facetime in my iphone; i already upload de i os 7.02 but the message still have it; it said that they have problem with the network; i reset the network and doesnt work

Hello, Toro Silva.
Thank you for visiting Apple Support Communities.
The steps in the section labeled Unable to activate FaceTime or iMessage with phone number and Apple ID after waiting 24 hours (iPhone only) of the article below, should help resolve the issue. Make sure to create a current backup prior to processing these steps.
iOS: Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/ts4268
Cheers,
Jason H

I have problems with office for mac screen resolution, specially with excel

I have problems with office for mac screen resolution, specially with excel ?

For starters, make sure to Check for Updates on any of the Help menus, and make sure the product has all the latest patches. MS did come out with a patch addressing the display issues on Retina Macs. Latest patchlevel is 14.3.2.
We are talking about Office:Mac 2011, right?

Is there problems with the network/signal in TA3 Taunton area

Is there problems with the network/signal in the TA3 Taunton area I have not had a signal all day and then to make contact with one of my children regarding school pick up.

Unfortunately so. Spoke to EE today and the service may take up to 72 hours to get back to normal - which is unbelievable given how much we use our phones for day to day life! As they cannot do anything for us, to thank us for our patience they are asking us to monitor when the service resumes and get back to them (no doubt on their £ per min line) and let them know and they’ll credit us for the down time. Just Brilliant!!

After installed mavericks i cannot sign in to my facetime and i messages. i tried it 100 times, but it is showing couldn't sign in check your network and try again. there is no problem with my network. if anyone knows the solution please help me .

After installed mavericks i cannot sign in to my facetime and i messages. i tried it 100 times, but it is showing couldn't sign in check your network and try again. there is no problem with my network. if anyone knows the solution please help me .

Hi,
What version of the OS did you upgrade from ?
Anything before OS X 10.8.2 may have an issue if the Logic/Mother board has been replaced and the Serial Number not "flashed" back to it.
In the Apple Icon menu use the About this Mac item.
In the new panel click twice on the line that tells you the current OS level
It will change to the Build number (and alternative count to the OS versions) and then the Serial Number.
If it is missing you need to get it replaced.
(It is supposed to be done on Repair or Refurbishment).
An Apple Store or Apple Authorised Service Provider as the best choices.
There are apps you can download (They are Mac Model specific) but needs careful typing as it is a once only trip.
8:56 pm Sunday; November 24, 2013
 iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad
Message was edited by: Ralph Johns (UK)

When i try to order prints i get an error message saying there is a problem with my network and my network is working

when i try to order prints i get an error message saying there is a problem with my network and my network is working. How can i solve this problem?

Try a different media. I have good luck using Maxell discs.

The problem with the network card.

The problem with the network card.
My laptop HP Pavilion dv7-1260ew network connection breaks .
NIC is to blame .
On that card could replace the old Intel 5100 to work with the network as a standard N.

Pawełek wrote:
The problem with the network card.
My laptop HP Pavilion dv7-1260ew network connection breaks .
NIC is to blame .
On that card could replace the old Intel 5100 to work with the network as a standard N.
This confusing which one are you asking about?
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

Report generation toolkit problem with office 2000 and office XP

Hello, I am having a problem with running my vi after it is compiled with application builder. The dev machine is an XP box and the targer is windows 2000. I included _Excel Dynamic VIs.vi and _Word Dynamic VIs.vi from the office 2000 section of the install cd (for the report toolkit) in the compile but did not include those files for XP. When I run the application on the target machine (2000), the reporting functions call Excel just fine and the program does not come up with any errors. The program however, is not loading the approprate template and inserting the approprate data. Did I leave some neccessary files out of the compile? Thanks in advance!
Greg
Gregory Osenbach, CLA
Fluke

Hi Acer,
The recommended procedure in your case is to install Microsoft Office 2000 on the development machine and then reinstall the LabVIEW Report Generation Toolkit. When the toolkit is installed, it will check for the current version of Office and install the corresponding VIs to support it. The VIs include different ActiveX calls according to the version of Office. Therefore it is not enough to change the support manually without having the correct version of Office installed first.
However, I would recommend that you just try to run your executable on a machine that has Office 2000 installed. The difference in the ActiveX API for Office XP and 2000 is not that significant, so your application might work perfectly on an Office 2000 machine. If you try to run the executable on a machine with Office 97 installed I'm willing to bet my right arm that you will experience errors.
Good luck Acer!
- Philip Courtois, Thinkbot Solutions

Problems with Office 2011 for mac after upgrading to Mountain Lion

Office 2011 for mac worked fine with Lion on my MacBook Air. I had been having some problems with my computer freezing and crashing, so the folks at the Genius Bar wiped my computer clean and installed Mountain Lion for me.
I have full backups (Time Machine) from before the wipe on my external hard drive, but I was told not to restore from the backup, that I should drag and drop files instead. I was also told to re-install any program for which I had the disk. I reinstalled Office 2011 via the disk.
Two major problems followed:
1.     I lost all my old emails (I use Mail). Even rebuilding the library or trying to restore them from Time Machine don't get them back.
2.     Word and Excel don't seem to recognize me anymore. I can pull up and modify an old document or workbook, but I cannot "save" my changes. I have to hit "save as." That's a pain, but there's a worse problem.
I have no trouble saving these "save as" versions to my desktop or to my Documents file. But I cannot save them anywhere else — even to the folder where I found the original document. I get a message that I don't have the necessary permissions to access or modify the folders. I'm asked to authenticate, and I do, but that doesn't seem to do anything.
I tried Get Info on the workbooks and documents, and I'm clearly granted Read and Write permission.
I've done a permissions repair via Disk Utility. There were some things to repair, but it didn't solve my problem.
I know I can move all documents to an external hard drive and then recreate all the folders, saving all the documents and workbooks "as" but it seems a huge amount of work. Can anybody suggest an easier route or how to get my email history?

You may need to rebuild permissions on your user account. To do this,boot to your Recovery partition (holding down the Command and R keys while booting) and open Terminal from the Utilities menu. In Terminal, type: 'resetpassword' (without the 's) and select the admin user. You are not going to reset your password. Click on the icon for your Macs hard drive at the top. From the drop down below it select the user account which is having issues. At the bottom of the window, you'll see an area labeled Restore Home Directory Permissions and ACLs. Click the reset button there. The process takes a few minutes. When complete, restart.
http://osxdaily.com/2011/11/15/repair-user-permissions-in-mac-os-x-lion/

Is anyone else having problems with Office for Mac and Lion?

Since installing Lion 10.7.1 on a macbook pro 2.53 Ghz 4GB 1067 MHz DDR3 I have had no end of problems. Both Excel and Word hang, crash and saving an Excel file is a pain. A 12mb spread sheet just took 4 minutes to save! I have MS Office for Mac 2011 version 14.1.3.
Another problem that may not be related to Office is that opening Finder is so slow and most of the time it takes a minute to display folders in Desktop or Documents.
Any suggestions would be welcome .. I regret installing Lion .. I had no problems with Snow Leopard!

botro wrote:
I'm unable to install the MS Office 14.1.3 update - I keep getting "Installation Failure"
I have not found a solution on this board or Microsoft community
This thread had some things to try.

Problems with office after upgrade to ERP 6.0

After upgrade from R3 46c to ERP 6.0 , we installed sap gui 710 with patch 14 and in many frontends a new version of Microsoft Office 2003 SP3.
In many PCs now we have a problem with macros and templates from PA20 transacction with Documents Management.
We try to execute a Wor for a personnel number with infotype 910 and I have the nex messages when Windows open the Word 2003.
"Al abrir este domento, se ejecutará el comando SQL siguiente:
SELECT * FROM C:/DOCUMEN1andreaCONFIG1TempDatasource_tab.SAP
Los datos de la base de datos se colocarán en el documento. ¿Desea continuar?"
If you select "Si", appear another message ~SAP(BA6580C1-BE84.... es un documento principal de combinación. Word no puede encontrar el origen de datos"
When, word document is dsplayed, we only see name of variable and they are not reeplaced by its value.

Sorry, but the note is in Spain (I guess), can you please translate?
We have the same issue on our productive HR system - but not on the development system, what makes it curious.
When we try to start contracts in word we get the same message
"Opening this will run the following SQL command
SELECT * FROM C:\.....Datasource_tab.SAP
How can we avoid this message?
Thanks in advance!

Problem with wifi network.

I've had my macbook pro for a little under a month and have had no problems with it up until this weekend. The problem is this; whenever I try to log onto a wifi network, the computer says that I'm connected but when I go to open Safari it says that I'm not connected to the internet. I've run a network diagnostic and it says that nothing appears to be wrong with the connection. Usually if I turn off my wifi and turn it back on I can get my connection to work but it usually takes a few tries. I've had the same issue both at my house and my parents' so the issue seems to be with my computer versus with a specific wifi network...any suggestions?

System Preferences > Network > WiFi/Airport > ( Assist me ) ...
... only this time, choose Set up again from scratch, including a new Location and answer the questions to set everything up again.

Problem with carrier network

I have a problem with mi iPhone 5s 64 Gb, time to time The carrier network still looking for network and some times it tooks until 2 minutes to find the net, im compare with friends to understand if this is a general problem with the carrier servíce but 1) some of them have the same phone without a problem using the same carrier, and 2) the must funny thing is that im working with the carrier company, so im really angry with this, i want to change my phone, i have images with the problem because this is really too much.
Are you going to help me? Or do i need to change mi phone!!!!!!!

This is just annoying!
Same thing in Germany! Updated my Iphone 6 (128gb) to Ios 8.0.1 late in the evening. Couldn´t restore it because of the traffic on Apple´s Server.
Now I´m sitting at work with my Ipod (lol) and just mentioned that even the Artwork of Movies or Music is lost. Just grey boxes.
This is not Apple anymore!!!
Is this the "just one more thing"?! --> Next time I will think twice before buying some stuff of apple!!

Problems With Office Network

Similar Messages

Maybe you are looking for