Problems with SATA and 865-Neo Series 2
Hi All,
My configuration is as follow:
MS-6278, 1GB OCZ RAM, Enermax 465VE P/S, Ti42008x, Seagate 250 and 320 SATA Perpendicular drives - no raid setup.
Okay - So I have 2 SATA drives and 2 PATA CDROMS in the computer.
Everything has been working fine until last night.
What happens now is that when I boot up the computer, the post screen comes up, all drives are detected and I get a single beep. Then the computer sits there. I watch the HDD light, and after the first initial seek and detect - the HDD never moves again.
I also tried booting off a CD by hitting F11 during the boot up tests. I get the option to select a CD drive, and select it, nothing happens. Stuck at post screen.
No power outages, no weird behavior up until I soft rebooted the machine. Since then I can't get past the BIOS.
I did do a factory BIOS reset and then I was able to boot using the Windows XP CD, but couldn't find the drives in recovery mode (since the SATA driver hadn't been loaded).
I tried leaving the working settings alone and disconnected the power to the SATA driver, and still could not boot off the CDROM with SATA setup.
Any help, ideas? Is my motherboard dead or something?
Thanks in advance!
CPU - Intel 2.8 Hyperthreading.
Really weird.
So I took your suggestion and downloaded Seagate tools. Then I reset the BIOS so that I could boot from the CD. Of course, my SATA drives were not found. So I went back and activated the SATA in the BIOS. This time, I put left the Seagate disk in and tried F11. Bingo - I was able to run the CD. Then I ran the File System and Quick Disk checks. The File system test said that both of my drives had files errors. The util said I needed to fix the files using the Windows disk.
Then I quit. I have three CD drives - so I left the Seagate disk in, and put in knoppix and windows. I attempted to boot of the Windows disk and got a cannot book NTLOADER error, then it went to the hard drives and started booting up the OS!
I rebooted once, no problems!
i am running Scandisk now on the boot drive - no errors on 1, 2, 3/5 stages - stage 4 in progress now.
I will keep you posted.
Similar Messages
-
Problems with 9600XT and k8t Neo 2
I have a problem with my 9600XT and my board...
Sometimes the board indicates grafic-card failure at post (8 beeps in a row).
After som trying it will work and windows will start. Games work just fine!
I should say that when i installed the new board my old 9600XT didnt work (8 beeps) And i had it replaced, and after getting the new 9600XT (RMA-return) it have worked just fine until a few days ago...
MSI k8t neo 2
Sapphire 9600XT
AMD 64 3500+
Q-TEC 550w (possible problem?)
Bios: 3.30
I also have a problem with the data execution (dont know it in english). explorer.exe is shutting down sometimes due to the data execution protection. No viruses according to nod32...Maybe you should your memory module in DIMM2 (the other green one), if it's in DIMM1 right now. Or you could try another module, if possible.
Here are the beep codes:
Quote
Beep codes for AMIBIOS (American Megatrends, Inc.):
Boot Block Beep Codes
Number of Beeps; Description:
1 ; Insert diskette in floppy drive A:
2 ; ‘AMIBOOT.ROM’ file not found in root directory of diskette in A:
3 ; Base Memory error
4 ; Flash Programming successful
5 ; Floppy read error
6 ; Keyboard controller BAT command failed
7 ; No Flash EPROM detected
8 ; Floppy controller failure
9 ; Boot Block BIOS checksum error
10 ; Flash Erase error
11 ; Flash Program error
12 ; ‘AMIBOOT.ROM’ file size error
13 ; BIOS ROM image mismatch (file layout does not match image present in flash device)
POST BIOS Beep Codes
Number of Beeps; Description:
1 ; Memory refresh timer error.
2 ; Parity error in base memory (first 64KB block)
3 ; Base memory read/write test error
4 ; Motherboard timer not operational
5 ; Processor error
6 ; 8042 Gate A20 test error (cannot switch to protected mode)
7 ; General exception error (processor exception interrupt error)
8 ; Display memory error (system video adapter)
9 ; AMIBIOS ROM checksum error
10 ; CMOS shutdown register read/write error
11 ; Cache memory test failed
Seems to me it's a POST bios beep code...keep trying with the Radeon 9600XT card installed.
-
My MacBook Pro 17" early 2011(built March) and my new OCZ sata III 6G are not working together, when is Apple going to admit there is a problem with the Intel's 6 Series Chipset. In System Information it says "Link Speed: 6 Gigabit" which is sata III and in my MacBook Pro it does not work.
Now MacBook Pro 17" early 2011 built May onward do not have this problem it was fixed in the Intel's 6 Series Chipset. (So there is a problem). Cam I have my MacBook Pro fixed please.After biting the bullet and ordering more RAM, my computer now is working a ton better. So that must have been the main issue. With 8 GB RAM, I can now even run Parallels fluidly (better than my work PC!) where before simple things like logging in to my MBP after reboot could take forever.
The place I went to had several other people getting RAM upgrades at the same time as me, so between this and other comments I've seen in discussions here and elsewhere on the Internets, I take it to mean that either Apple should bump up the base RAM on its new machines, and/or stop charging so much for additional RAM.
I refused to believe a Pro machine bought with Lion installed would come with too little RAM for light to medium usage, but it was apparently the case. I'll mark this as a correct answer and hope some other poor soul will come across this thread and be helped by it. -
Problem with writing and reading using serialization
I am having a problem with writing and reading an object that has another object in it. The purpose of the class is to write a order that has multiple items in it. And there will be several orders. This is for an IB project, where one of the requirements is to utilize a hierarchical composite data structure. That is, it is "one that contains more than one element and at least one of the elements is a composite data structure. Examples are, an array or linked list of records, a record that has one field that is another record, or an array". The code is shown below:
The error produced is
java.lang.NullPointerException
at SamsonRubberIndustries.CustomerOrderDetails.createCustOrdDetailsScreen(CustomerOrderDetails.java:150)
at SamsonRubberIndustries.CustomerOrderDetails$1.run(CustomerOrderDetails.java:78)
at java.awt.event.InvocationEvent.dispatch(Unknown Source)
at java.awt.EventQueue.dispatchEvent(Unknown Source)
at java.awt.EventDispatchThread.pumpOneEventForFilters(Unknown Source)
at java.awt.EventDispatchThread.pumpEventsForFilter(Unknown Source)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(Unknown Source)
at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
at java.awt.EventDispatchThread.run(Unknown Source)
public class CustOrdObject implements Serializable {
public int CustID;
public int CustOrderID;
public Object OrderDate;
public InnerCustOrdObject[] innerCustOrdObj;
public float GrandTotal;
public int MaxItems;
public CustOrdObject() {}
public CustOrdObject(InnerCustOrdObject[] innerCustOrdObj,
int CustID, int CustOrderID, Object OrderDate,
float GrandTotal, int innerarrlength, int innerarrpos, int MaxItems) {
this.CustID = CustID;
this.CustOrderID = CustOrderID;
this.OrderDate = OrderDate;
this.GrandTotal = GrandTotal;
this.MaxItems = MaxItems;
this.innerCustOrdObj = new InnerCustOrdObject[MaxItems];
public InnerCustOrdObject[] getInnerCustOrdObj() {
return innerCustOrdObj;
public void setInnerCustOrdObj(InnerCustOrdObject[] innerCustOrdObj) {
this.innerCustOrdObj = innerCustOrdObj;
public int getCustID() {
return CustID;
public void setCustID(int custID) {
CustID = custID;
public int getCustOrderID() {
return CustOrderID;
public void setCustOrderID(int custOrderID) {
CustOrderID = custOrderID;
public Object getOrderDate() {
return OrderDate;
public void setOrderDate(Object orderDate) {
OrderDate = orderDate;
public void setGrandTotal(float grandTotal) {
GrandTotal = grandTotal;
public float getGrandTotal() {
return GrandTotal;
public int getMaxItems() {
return MaxItems;
public void setMaxItems(int maxItems) {
MaxItems = maxItems;
public class InnerCustOrdObject implements Serializable{
public int ItemNumber;
public float UnitPrice;
public int QuantityRequired;
public float TotalPrice;
public InnerCustOrdObject() {}
public InnerCustOrdObject(int ItemNumber, float
UnitPrice, int QuantityRequired, float TotalPrice){
this.ItemNumber = ItemNumber;
this.UnitPrice = UnitPrice;
this.QuantityRequired = QuantityRequired;
this.TotalPrice = TotalPrice;
public int getItemNumber() {
return ItemNumber;
public void setItemNumber(int itemNumber) {
ItemNumber = itemNumber;
public int getQuantityRequired() {
return QuantityRequired;
public void setQuantityRequired(int quantityRequired) {
QuantityRequired = quantityRequired;
public float getTotalPrice() {
return TotalPrice;
public void setTotalPrice(float totalPrice) {
TotalPrice = totalPrice;
public float getUnitPrice() {
return UnitPrice;
public void setUnitPrice(float unitPrice) {
UnitPrice = unitPrice;
import java.awt.*;
import java.awt.event.*;
import java.io.*;
import java.text.SimpleDateFormat;
import java.util.Date;
import javax.swing.*;
import javax.swing.table.DefaultTableCellRenderer;
import javax.swing.table.DefaultTableModel;
public class CustomerOrderDetails extends CommonFeatures{
//TODO
private static int MAX_ORDERS = 200;
private static int MAX_ORDERITEMS = 100;
private static int MaxRecord;
private static int CurrentRecord = 1;
private static int currentItem;
private static int MaxItems;
private static boolean FileExists, recFileExists;
private static CustOrdObject[] orderDetails = new CustOrdObject[MAX_ORDERS];
private static InnerCustOrdObject[] innerCustOrdObj = new InnerCustOrdObject[MAX_ORDERITEMS];
private static File OrderDetailsFile = new File("CustOrdDetails.dat");
private static File OrdRecordNumStore = new File("OrdRecordNumStore.txt");
private static PrintWriter writeFile;
private static BufferedReader readFile;
private static ObjectOutputStream objOut;
private static ObjectInputStream objIn;
//Set format for date
SimpleDateFormat simpleDF = new SimpleDateFormat("dd MM yyyy");
//--<BEGINNING>--Declaring Interface Variables------------------------------------------//
private JPanel innertoppanel, innercenterpanel, innerbottompanel, innerrightpanel, innerleftpanel;
private JLabel CustIDLbl, CustOrderIDLbl, OrderedDateLbl, GrandTotLbl, ItemNumberLbl,UnitPriceLbl, QuantityReqLbl, TotPriceLbl;
private JTextField CustIDTxt, CustOrderIDTxt, OrderedDateTxt, GrandTotTxt, ItemNumberTxt, UnitPriceTxt, QuantityReqTxt, TotPriceTxt;
private JButton addrecordbtn, savebtn, externalprevbtn, externalnextbtn, internalprevbtn, internalnextbtn, gotorecordbtn, additemreqbtn;
//--<END>--Declaring Interface Variables------------------------------------------------//
public static void main(String[] args) {
final CustomerOrderDetails COD = new CustomerOrderDetails();
java.awt.EventQueue.invokeLater(new Runnable() {
public void run() {
try {
UIManager.setLookAndFeel("com.sun.java.swing.plaf.windows.WindowsLookAndFeel");
COD.createCustOrdDetailsScreen();
} catch (Exception eb) {
eb.printStackTrace();
//--<BEGINNING>--Creating CustomerOrderDetails Screen---------------------------------------//
public JFrame createCustOrdDetailsScreen() {
createDefaultFrame();
mainframe.setSize(800,500);
createContainerPanel();
containerpanel.add(createCustOrdDetailsTitle(), BorderLayout.NORTH);
containerpanel.add(createCustOrdDetailsMainPanel(), BorderLayout.CENTER);
//containerpanel.add(createCustOrdDetailsLeftNavButtons(), BorderLayout.WEST);
//containerpanel.add(createCustOrdDetailsRightNavButtons(), BorderLayout.EAST);
containerpanel.add(createCustOrdDetailsButtons(), BorderLayout.SOUTH);
mainframe.setContentPane(containerpanel);
mainframe.setLocationRelativeTo(null);
mainframe.setVisible(true);
//--<BEGINNING>--Checks to see whether CRecordNumberStore file exists-------------------------------//
if (OrdRecordNumStore.exists() == true) {
recFileExists = true;
}else {
recFileExists = false;
if (recFileExists == true) {
MaxRecord = readRecordNumber();
CurrentRecord = MaxRecord;
//readOrder();
//readInnerOrderRecord(CurrentRecord);
System.out.println("Current Record " +CurrentRecord);
System.out.println("Max Record " +MaxRecord);
}else{
MaxRecord = 1;
writeRecordNumber(MaxRecord);
CustOrderIDTxt.setText(""+MaxRecord);
System.out.println("Current Record " +CurrentRecord);
System.out.println("Max Record " +MaxRecord);
//--<END>--Checks to see whether CRecordNumberStore file exists--------------------------------------//
if(readOrder() != null){
orderDetails = (CustOrdObject[]) readOrder();
innerCustOrdObj = orderDetails[CurrentRecord].getInnerCustOrdObj();
MaxItems = orderDetails[CurrentRecord].getMaxItems();
if(CurrentRecord > 1 && CurrentRecord < MaxRecord){
externalnextbtn.setEnabled(true);
externalprevbtn.setEnabled(true);
if(CurrentRecord >= MaxRecord){
externalnextbtn.setEnabled(false);
getFieldText(CurrentRecord-1);
}else{
orderDetails[CurrentRecord] = new CustOrdObject();
currentItem = 1;
return mainframe;
//--<END>--Creating CustomerOrderDetails Screen---------------------------------------------//
public JPanel createCustOrdDetailsTitle(){
createTitlePanel();
titlepanel.setBackground(TxtfontColor);
label.setText("- Customer Order Details -");
labelpanel.setBackground(TxtfontColor);
label.setForeground(Color.white);
createbuttonpanel();
buttonpanel.setBackground(TxtfontColor) ;
buttonpanel.add(createReturnToMainMenuButton());
titlepanel.add(labelpanel, BorderLayout.WEST);
titlepanel.add(buttonpanel, BorderLayout.EAST);
return titlepanel;
public JPanel createCustOrdDetailsMainPanel(){
createmainpanel();
mainpanel.setBackground(TxtfontColor);
mainpanel.setLayout(new BorderLayout());
mainpanel.setBorder(BorderFactory.createTitledBorder(""));
mainpanel.add(createInnerTopPanel(), BorderLayout.NORTH);
mainpanel.add(createInnerCenterPanel(), BorderLayout.CENTER);
mainpanel.add(createInnerBottomPanel(), BorderLayout.SOUTH);
mainpanel.add(createInnerRightPanel(), BorderLayout.EAST);
mainpanel.add(createInnerLeftPanel(), BorderLayout.WEST);
return mainpanel;
public JPanel createInnerTopPanel(){
innertoppanel = new JPanel(new GridBagLayout());
innertoppanel.setBackground(TxtfontColor);
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
//Setting Font Type and Size
Font font = new Font("Arial", Font.BOLD, 11);
CustIDLbl = new JLabel("Customer ID");
CustIDLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
CustIDLbl.setFont(font);
CustIDLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 1;
innertoppanel.add(CustIDLbl, GBC);
CustIDTxt = new JTextField(20);
CustIDTxt.setEditable(true);
GBC.gridx = 2;
GBC.gridy = 1;
innertoppanel.add(CustIDTxt, GBC);
GBC.gridx = 3;
GBC.gridy = 1;
innertoppanel.add(Box.createHorizontalStrut(220), GBC);
OrderedDateLbl = new JLabel("Order Date");
OrderedDateLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
OrderedDateLbl.setFont(font);
OrderedDateLbl.setForeground(LblfontColor);
GBC.gridx = 4;
GBC.gridy = 1;
innertoppanel.add(OrderedDateLbl, GBC);
//Get today's date
Date todaydate = new Date();
OrderedDateTxt = new JTextField(simpleDF.format(todaydate), 20);
OrderedDateTxt.setHorizontalAlignment(JTextField.CENTER);
OrderedDateTxt.setEditable(false);
GBC.gridx = 5;
GBC.gridy = 1;
innertoppanel.add(OrderedDateTxt, GBC);
CustOrderIDLbl = new JLabel("Customer Order ID");
CustOrderIDLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
CustOrderIDLbl.setFont(font);
CustOrderIDLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 2;
innertoppanel.add(CustOrderIDLbl, GBC);
CustOrderIDTxt = new JTextField(20);
CustOrderIDTxt.setEditable(false);
GBC.gridx = 2;
GBC.gridy = 2;
innertoppanel.add(CustOrderIDTxt, GBC);
return innertoppanel;
public JPanel createInnerCenterPanel(){
innercenterpanel = new JPanel(new GridBagLayout());
innercenterpanel.setBackground(TxtfontColor);
innercenterpanel.setBorder(BorderFactory.createLoweredBevelBorder());
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
//Setting Font Type and Size
Font font = new Font("Arial", Font.BOLD, 11);
ItemNumberLbl = new JLabel("Item Number");
ItemNumberLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
ItemNumberLbl.setFont(font);
ItemNumberLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 1;
innercenterpanel.add(ItemNumberLbl, GBC);
ItemNumberTxt = new JTextField(20);
GBC.gridx = 2;
GBC.gridy = 1;
innercenterpanel.add(ItemNumberTxt, GBC);
UnitPriceLbl = new JLabel("Unit Price");
UnitPriceLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
UnitPriceLbl.setFont(font);
UnitPriceLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 2;
innercenterpanel.add(UnitPriceLbl, GBC);
UnitPriceTxt = new JTextField(20);
//UnitPriceTxt.setEditable(false);
GBC.gridx = 2;
GBC.gridy = 2;
innercenterpanel.add(UnitPriceTxt, GBC);
QuantityReqLbl = new JLabel("Quantity Required");
QuantityReqLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
QuantityReqLbl.setFont(font);
QuantityReqLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 3;
innercenterpanel.add(QuantityReqLbl, GBC);
QuantityReqTxt = new JTextField(20);
//QuantityReqTxt.setEditable(false);
GBC.gridx = 2;
GBC.gridy = 3;
innercenterpanel.add(QuantityReqTxt, GBC);
TotPriceLbl = new JLabel("Total Price");
TotPriceLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
TotPriceLbl.setFont(font);
TotPriceLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 4;
innercenterpanel.add(TotPriceLbl, GBC);
TotPriceTxt = new JTextField(20);
//TotPriceTxt.setEditable(false);
GBC.gridx = 2;
GBC.gridy = 4;
innercenterpanel.add(TotPriceTxt, GBC);
return innercenterpanel;
public JPanel createInnerBottomPanel(){
innerbottompanel = new JPanel(new FlowLayout(FlowLayout.RIGHT));
innerbottompanel.setBackground(TxtfontColor);
//Setting Font Type and Size
Font font = new Font("Arial", Font.BOLD, 11);
GrandTotLbl = new JLabel("Grand Total");
GrandTotLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
GrandTotLbl.setFont(font);
GrandTotLbl.setForeground(LblfontColor);
innerbottompanel.add(GrandTotLbl);
innerbottompanel.add(Box.createHorizontalStrut(30));
GrandTotTxt = new JTextField(20);
innerbottompanel.add(GrandTotTxt);
return innerbottompanel;
public JPanel createInnerRightPanel(){
innerrightpanel = new JPanel(new FlowLayout(FlowLayout.CENTER));
innerrightpanel.setBackground(TxtfontColor);
innerrightpanel.setLayout(new BoxLayout(navrightpanel, BoxLayout.Y_AXIS));
innerrightpanel.setBorder(BorderFactory.createLoweredBevelBorder());
innerrightpanel.setLayout(new GridBagLayout());
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
internalnextbtn = new JButton(createNextButtonIcon());
GBC.gridx = 1;
GBC.gridy = 1;
internalnextbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
//getInnerFieldText(currentItem);
internalprevbtn.setEnabled(true);
if(currentItem < MaxItems){
++CurrentRecord;
//readOrder();
//readInnerOrderRecord(CurrentRecord);
setInnerFieldText(currentItem);
System.out.println(CurrentRecord);//Checking RECORD_NUM
if(currentItem == MaxItems){
internalnextbtn.setEnabled(false);
innerrightpanel.add(internalnextbtn, GBC);
return innerrightpanel;
public JPanel createInnerLeftPanel(){
innerleftpanel = new JPanel(new FlowLayout(FlowLayout.CENTER));
innerleftpanel.setBackground(TxtfontColor);
innerleftpanel.setBorder(BorderFactory.createLoweredBevelBorder());
innerleftpanel.setForeground(Color.BLACK);
innerleftpanel.setLayout(new GridBagLayout());
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
internalprevbtn = new JButton(createPreviousButtonIcon());
GBC.gridx = 1;
GBC.gridy = 1;
internalprevbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
//getInnerFieldText(currentItem);
internalnextbtn.setEnabled(true);
if(currentItem == 1){
internalprevbtn.setEnabled(false);
if(currentItem > 0){
--currentItem;
//readOrder();
setInnerFieldText(currentItem);
innerleftpanel.add(internalprevbtn, GBC);
return innerleftpanel;
public JPanel createCustOrdDetailsButtons(){
createbuttonpanel();
buttonpanel.setBackground(TxtfontColor);
externalprevbtn = new JButton(createPreviousButtonIcon());
externalprevbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
getFieldText(CurrentRecord);
externalnextbtn.setEnabled(true);
if(CurrentRecord == 1){
externalprevbtn.setEnabled(false);
if(CurrentRecord > 0){
--CurrentRecord;
setFieldText(CurrentRecord);
System.out.println(CurrentRecord);//Checking RECORD_NUM
buttonpanel.add(externalprevbtn);
addrecordbtn = new JButton("Add Record", createAddButtonIcon());
addrecordbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
try{
MaxRecord = readRecordNumber();
MaxRecord++;
writeRecordNumber(MaxRecord);
//--<BEGINNING>--Clear Fields-------------------------------------------------------//
CustIDTxt.setText("");
CustOrderIDTxt.setText(""+MaxRecord);
//Get today's date
Date todaydate = new Date();
OrderedDateTxt.setText(""+simpleDF.format(todaydate));
ItemNumberTxt.setText("");
UnitPriceTxt.setText("");
QuantityReqTxt.setText("");
TotPriceTxt.setText("");
GrandTotTxt.setText("");
//--<END>--Clear Fields-------------------------------------------------------------//
externalnextbtn.setEnabled(false);
externalprevbtn.setEnabled(true);
System.out.println(MaxRecord);
} catch(Exception ec){ec.printStackTrace();}
buttonpanel.add(addrecordbtn);
savebtn = new JButton("Save Data", createSaveButtonIcon());
savebtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
setFieldText(CurrentRecord);
writeOrder();
writeRecordNumber(MaxRecord);
System.out.println(CurrentRecord);
System.out.println(MaxRecord);
buttonpanel.add(savebtn);
java.net.URL imageURL_AddRowIcon = CommonFeatures.class.getResource("Icons/edit_add.png");
ImageIcon AddRowIcon = new ImageIcon(imageURL_AddRowIcon);
additemreqbtn = new JButton("Add Item", AddRowIcon);
additemreqbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
try{
//--<BEGINNING>--Clear Fields-------------------------------------------------------//
ItemNumberTxt.setText("");
UnitPriceTxt.setText("");
QuantityReqTxt.setText("");
TotPriceTxt.setText("");
//--<END>--Clear Fields-------------------------------------------------------------//
//CurrentRecord = MaxRecord;
currentItem++;
setInnerFieldText(currentItem);
internalnextbtn.setEnabled(false);
internalprevbtn.setEnabled(true);
System.out.println(MaxRecord);
} catch(Exception ec){ec.printStackTrace();}
buttonpanel.add(additemreqbtn);
externalnextbtn = new JButton(createNextButtonIcon());
externalnextbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
getFieldText(CurrentRecord);
externalprevbtn.setEnabled(true);
if(CurrentRecord < MaxRecord){
++CurrentRecord;
setFieldText(CurrentRecord);
System.out.println(CurrentRecord);//Checking RECORD_NUM
if(CurrentRecord == MaxRecord){
externalnextbtn.setEnabled(false);
buttonpanel.add(externalnextbtn);
return buttonpanel;
//TODO
public void setFieldText(int orderID){//TODO
orderDetails[orderID].setCustID(Integer.parseInt(CustIDTxt.getText()));
orderDetails[orderID].setCustOrderID(Integer.parseInt(CustOrderIDTxt.getText()));
orderDetails[orderID].setOrderDate(OrderedDateTxt.getText());
orderDetails[orderID].setInnerCustOrdObj(innerCustOrdObj);
orderDetails[orderID].setMaxItems(MaxItems);
setInnerFieldText(currentItem);
orderDetails[orderID].setGrandTotal(Float.parseFloat(GrandTotTxt.getText()));
public void setInnerFieldText(int currentItem){//TODO
innerCustOrdObj[currentItem] = new InnerCustOrdObject();
innerCustOrdObj[currentItem].setItemNumber(Integer.parseInt(ItemNumberTxt.getText()));
innerCustOrdObj[currentItem].setUnitPrice(Float.parseFloat(UnitPriceTxt.getText()));
innerCustOrdObj[currentItem].setQuantityRequired(Integer.parseInt(QuantityReqTxt.getText()));
innerCustOrdObj[currentItem].setTotalPrice(Float.parseFloat(TotPriceTxt.getText()));
public void getFieldText(int orderID){
CustIDTxt.setText(Integer.toString(orderDetails[orderID].getCustID()));
CustOrderIDTxt.setText(Integer.toString(orderDetails[orderID].getCustOrderID()));
OrderedDateTxt.setText(""+orderDetails[orderID].getOrderDate());
currentItem = orderDetails[orderID].getMaxItems();
System.err.println("currentItem" + currentItem);
getInnerFieldText(currentItem);
GrandTotTxt.setText(Float.toString(orderDetails[orderID].getGrandTotal()));
public void getInnerFieldText(int currentItem){
ItemNumberTxt.setText(Integer.toString(innerCustOrdObj[currentItem].getItemNumber()));
UnitPriceTxt.setText(Float.toString(innerCustOrdObj[currentItem].getUnitPrice()));
QuantityReqTxt.setText(Integer.toString(innerCustOrdObj[currentItem].getQuantityRequired()));
TotPriceTxt.setText(Float.toString(innerCustOrdObj[currentItem].getTotalPrice()));
public void writeOrder(){//TODO
try {
objOut = new ObjectOutputStream(new FileOutputStream(OrderDetailsFile));
objOut.writeObject(orderDetails);
System.out.println("WORKING!");
objOut.flush();
objOut.close();
} catch (IOException e) {
e.printStackTrace();
public Object readOrder(){
Object temporaryObj;
try{
objIn = new ObjectInputStream(new FileInputStream(OrderDetailsFile));
temporaryObj = objIn.readObject();
CustOrdObject[] blah = (CustOrdObject[]) temporaryObj;
System.out.println("Outer: "+blah[1].getCustID());
InnerCustOrdObject[] whee = blah[1].getInnerCustOrdObj();
System.out.println("Inner: "+whee[1].getItemNumber());
objIn.close();
System.out.println("Read Worky!");
return temporaryObj;
}catch(Exception e){
e.printStackTrace();
System.out.println("Read No Worky!");
return null;
public void writeRecordNumber(int MaxRecord){
try{
objOut = new ObjectOutputStream(new FileOutputStream(OrdRecordNumStore));
objOut.writeObject(MaxRecord);
System.out.println("WORKING!");
objOut.flush();
objOut.close();
}catch(Exception e){e.printStackTrace();}
public int readRecordNumber() {
try {
objIn = new ObjectInputStream(new FileInputStream(OrdRecordNumStore));
int temporaryObj = Integer.parseInt(objIn.readObject().toString());
objIn.close();
System.out.println("Read Number Worky!");
return temporaryObj;
} catch (Exception e) {
e.printStackTrace();
System.out.println("Read Number No Worky!");
return -1;
}Message was edited by:
Kilik07
Message was edited by:
Kilik07ok i got reading to work to a certain extent... but the prob is i cnt seem to save my innerCustOrdObj proprly...when ever i look for a record using the gotorecordbtn, the outerobject, which is the orderDetails, seems to change but the innerCustOrdObj remains the same... heres the new code..
public class CustomerOrderDetails extends CommonFeatures{
//TODO
private static int MAX_ORDERS = 200;
private static int MAX_ORDERITEMS = 100;
private static int MaxRecord;
private static int CurrentRecord = 1;
private static int currentItem;
private static int MaxItems = 1;
private static boolean FileExists, recFileExists;
private static boolean RecordExists;
private static CustOrdObject[] orderDetails = new CustOrdObject[MAX_ORDERS];
private static InnerCustOrdObject[] innerCustOrdObj = new InnerCustOrdObject[MAX_ORDERITEMS];
private static File OrderDetailsFile = new File("CustOrdDetails.ser");
private static File OrdRecordNumStore = new File("OrdRecordNumStore.txt");
private static PrintWriter writeFile;
private static BufferedReader readFile;
private static ObjectOutputStream objOut;
private static ObjectInputStream objIn;
//Set format for date
SimpleDateFormat simpleDF = new SimpleDateFormat("dd MM yyyy");
//--<BEGINNING>--Declaring Interface Variables------------------------------------------//
private JPanel innertoppanel, innercenterpanel, innerbottompanel, innerrightpanel, innerleftpanel;
private JLabel CustIDLbl, CustOrderIDLbl, OrderedDateLbl, GrandTotLbl, ItemNumberLbl,UnitPriceLbl, QuantityReqLbl, TotPriceLbl;
private JTextField CustIDTxt, CustOrderIDTxt, OrderedDateTxt, GrandTotTxt, ItemNumberTxt, UnitPriceTxt, QuantityReqTxt, TotPriceTxt;
private JButton addrecordbtn, savebtn, externalprevbtn, externalnextbtn, internalprevbtn, internalnextbtn, gotorecordbtn, additemreqbtn;
//--<END>--Declaring Interface Variables------------------------------------------------//
public static void main(String[] args) {
final CustomerOrderDetails COD = new CustomerOrderDetails();
java.awt.EventQueue.invokeLater(new Runnable() {
public void run() {
try {
UIManager.setLookAndFeel("com.sun.java.swing.plaf.windows.WindowsLookAndFeel");
COD.createCustOrdDetailsScreen();
} catch (Exception eb) {
eb.printStackTrace();
//--<BEGINNING>--Creating CustomerOrderDetails Screen---------------------------------------//
public JFrame createCustOrdDetailsScreen() {
createDefaultFrame();
mainframe.setSize(800,500);
createContainerPanel();
containerpanel.add(createCustOrdDetailsTitle(), BorderLayout.NORTH);
containerpanel.add(createCustOrdDetailsMainPanel(), BorderLayout.CENTER);
//containerpanel.add(createCustOrdDetailsLeftNavButtons(), BorderLayout.WEST);
//containerpanel.add(createCustOrdDetailsRightNavButtons(), BorderLayout.EAST);
containerpanel.add(createCustOrdDetailsButtons(), BorderLayout.SOUTH);
mainframe.setContentPane(containerpanel);
mainframe.setLocationRelativeTo(null);
mainframe.setVisible(true);
//--<BEGINNING>--Checks to see whether CRecordNumberStore file exists-------------------------------//
if (OrdRecordNumStore.exists() == true) {
recFileExists = true;
}else {
recFileExists = false;
if (recFileExists == true) {
MaxRecord = readRecordNumber();
CurrentRecord = MaxRecord;
//readOrder();
//readInnerOrderRecord(CurrentRecord);
System.out.println("Current Record " +CurrentRecord);
System.out.println("Max Record " +MaxRecord);
}else{
MaxRecord = 1;
writeRecordNumber(MaxRecord);
CustOrderIDTxt.setText(""+MaxRecord);
System.out.println("Current Record " +CurrentRecord);
System.out.println("Max Record " +MaxRecord);
//--<END>--Checks to see whether CRecordNumberStore file exists--------------------------------------//
if(readOrder() != null){
orderDetails = (CustOrdObject[]) readOrder();
//CurrentRecord--;
//System.out.println("Current Rec Here"+CurrentRecord);
if(orderDetails[CurrentRecord] == null){
System.err.println("CustomerOrderObj 1 is null !!");
}else{
System.err.println("CustomerOrderObj 1 is not null !!");
if(orderDetails[CurrentRecord].getInnerCustOrdObj() == null){
System.err.println("InnerCustomerOrderObj is null !!");
}else{
System.err.println("InnerCustomerOrderObj is not null !!");
innerCustOrdObj = orderDetails[CurrentRecord].getInnerCustOrdObj();
MaxItems = orderDetails[CurrentRecord].getMaxItems();
if(CurrentRecord > 1 && CurrentRecord < MaxRecord){
externalnextbtn.setEnabled(true);
externalprevbtn.setEnabled(true);
if(CurrentRecord >= MaxRecord){
externalnextbtn.setEnabled(false);
getFieldText(CurrentRecord);
getInnerFieldText(MaxItems);
}else{
orderDetails[CurrentRecord] = new CustOrdObject();
currentItem = 1;
return mainframe;
//--<END>--Creating CustomerOrderDetails Screen---------------------------------------------//
public JPanel createCustOrdDetailsTitle(){
createTitlePanel();
titlepanel.setBackground(TxtfontColor);
label.setText("- Customer Order Details -");
labelpanel.setBackground(TxtfontColor);
label.setForeground(Color.white);
createbuttonpanel();
buttonpanel.setBackground(TxtfontColor) ;
buttonpanel.add(createReturnToMainMenuButton());
titlepanel.add(labelpanel, BorderLayout.WEST);
titlepanel.add(buttonpanel, BorderLayout.EAST);
return titlepanel;
public JPanel createCustOrdDetailsMainPanel(){
createmainpanel();
mainpanel.setBackground(TxtfontColor);
mainpanel.setLayout(new BorderLayout());
mainpanel.setBorder(BorderFactory.createTitledBorder(""));
mainpanel.add(createInnerTopPanel(), BorderLayout.NORTH);
mainpanel.add(createInnerCenterPanel(), BorderLayout.CENTER);
mainpanel.add(createInnerBottomPanel(), BorderLayout.SOUTH);
mainpanel.add(createInnerRightPanel(), BorderLayout.EAST);
mainpanel.add(createInnerLeftPanel(), BorderLayout.WEST);
return mainpanel;
public JPanel createInnerTopPanel(){
innertoppanel = new JPanel(new GridBagLayout());
innertoppanel.setBackground(TxtfontColor);
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
//Setting Font Type and Size
Font font = new Font("Arial", Font.BOLD, 11);
CustIDLbl = new JLabel("Customer ID");
CustIDLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
CustIDLbl.setFont(font);
CustIDLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 1;
innertoppanel.add(CustIDLbl, GBC);
CustIDTxt = new JTextField(20);
CustIDTxt.setEditable(true);
GBC.gridx = 2;
GBC.gridy = 1;
innertoppanel.add(CustIDTxt, GBC);
GBC.gridx = 3;
GBC.gridy = 1;
innertoppanel.add(Box.createHorizontalStrut(220), GBC);
OrderedDateLbl = new JLabel("Order Date");
OrderedDateLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
OrderedDateLbl.setFont(font);
OrderedDateLbl.setForeground(LblfontColor);
GBC.gridx = 4;
GBC.gridy = 1;
innertoppanel.add(OrderedDateLbl, GBC);
//Get today's date
Date todaydate = new Date();
OrderedDateTxt = new JTextField(simpleDF.format(todaydate), 20);
OrderedDateTxt.setHorizontalAlignment(JTextField.CENTER);
OrderedDateTxt.setEditable(false);
GBC.gridx = 5;
GBC.gridy = 1;
innertoppanel.add(OrderedDateTxt, GBC);
CustOrderIDLbl = new JLabel("Customer Order ID");
CustOrderIDLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
CustOrderIDLbl.setFont(font);
CustOrderIDLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 2;
innertoppanel.add(CustOrderIDLbl, GBC);
CustOrderIDTxt = new JTextField(20);
//CustOrderIDTxt.setEditable(false);
GBC.gridx = 2;
GBC.gridy = 2;
innertoppanel.add(CustOrderIDTxt, GBC);
return innertoppanel;
public JPanel createInnerCenterPanel(){
innercenterpanel = new JPanel(new GridBagLayout());
innercenterpanel.setBackground(TxtfontColor);
innercenterpanel.setBorder(BorderFactory.createLoweredBevelBorder());
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
//Setting Font Type and Size
Font font = new Font("Arial", Font.BOLD, 11);
ItemNumberLbl = new JLabel("Item Number");
ItemNumberLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
ItemNumberLbl.setFont(font);
ItemNumberLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 1;
innercenterpanel.add(ItemNumberLbl, GBC);
ItemNumberTxt = new JTextField(20);
GBC.gridx = 2;
GBC.gridy = 1;
innercenterpanel.add(ItemNumberTxt, GBC);
UnitPriceLbl = new JLabel("Unit Price");
UnitPriceLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
UnitPriceLbl.setFont(font);
UnitPriceLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 2;
innercenterpanel.add(UnitPriceLbl, GBC);
UnitPriceTxt = new JTextField(20);
//UnitPriceTxt.setEditable(false);
GBC.gridx = 2;
GBC.gridy = 2;
innercenterpanel.add(UnitPriceTxt, GBC);
QuantityReqLbl = new JLabel("Quantity Required");
QuantityReqLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
QuantityReqLbl.setFont(font);
QuantityReqLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 3;
innercenterpanel.add(QuantityReqLbl, GBC);
QuantityReqTxt = new JTextField(20);
//QuantityReqTxt.setEditable(false);
GBC.gridx = 2;
GBC.gridy = 3;
innercenterpanel.add(QuantityReqTxt, GBC);
TotPriceLbl = new JLabel("Total Price");
TotPriceLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
TotPriceLbl.setFont(font);
TotPriceLbl.setForeground(LblfontColor);
GBC.gridx = 1;
GBC.gridy = 4;
innercenterpanel.add(TotPriceLbl, GBC);
TotPriceTxt = new JTextField(20);
TotPriceTxt.setEditable(false);
TotPriceTxt.addFocusListener(new FocusAdapter(){
public void focusGained(FocusEvent evt){
TotPriceTxt.setText(""+Integer.parseInt(UnitPriceTxt.getText())*Integer.parseInt(QuantityReqTxt.getText()));
GBC.gridx = 2;
GBC.gridy = 4;
innercenterpanel.add(TotPriceTxt, GBC);
return innercenterpanel;
public JPanel createInnerBottomPanel(){
innerbottompanel = new JPanel(new FlowLayout(FlowLayout.RIGHT));
innerbottompanel.setBackground(TxtfontColor);
//Setting Font Type and Size
Font font = new Font("Arial", Font.BOLD, 11);
GrandTotLbl = new JLabel("Grand Total");
GrandTotLbl.setBorder(BorderFactory.createEmptyBorder(10,10,10,10));
GrandTotLbl.setFont(font);
GrandTotLbl.setForeground(LblfontColor);
innerbottompanel.add(GrandTotLbl);
innerbottompanel.add(Box.createHorizontalStrut(30));
GrandTotTxt = new JTextField(20);
innerbottompanel.add(GrandTotTxt);
return innerbottompanel;
public JPanel createInnerRightPanel(){
innerrightpanel = new JPanel(new FlowLayout(FlowLayout.CENTER));
innerrightpanel.setBackground(TxtfontColor);
innerrightpanel.setLayout(new BoxLayout(navrightpanel, BoxLayout.Y_AXIS));
innerrightpanel.setBorder(BorderFactory.createLoweredBevelBorder());
innerrightpanel.setLayout(new GridBagLayout());
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
internalnextbtn = new JButton(createNextButtonIcon());
GBC.gridx = 1;
GBC.gridy = 1;
internalnextbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
getInnerFieldText(currentItem);
internalprevbtn.setEnabled(true);
if(currentItem < MaxItems){
++currentItem;
orderDetails[CurrentRecord].getInnerCustOrdObj();
setInnerFieldText(currentItem);
System.out.println("Current Item" + currentItem);
if(currentItem == MaxItems){
internalnextbtn.setEnabled(false);
innerrightpanel.add(internalnextbtn, GBC);
return innerrightpanel;
public JPanel createInnerLeftPanel(){
innerleftpanel = new JPanel(new FlowLayout(FlowLayout.CENTER));
innerleftpanel.setBackground(TxtfontColor);
innerleftpanel.setBorder(BorderFactory.createLoweredBevelBorder());
innerleftpanel.setForeground(Color.BLACK);
innerleftpanel.setLayout(new GridBagLayout());
GridBagConstraints GBC = new GridBagConstraints();
GBC.fill = GridBagConstraints.HORIZONTAL;
internalprevbtn = new JButton(createPreviousButtonIcon());
GBC.gridx = 1;
GBC.gridy = 1;
internalprevbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
getInnerFieldText(currentItem);
internalnextbtn.setEnabled(true);
if(currentItem == 1){
internalprevbtn.setEnabled(false);
if(currentItem > 0){
--currentItem;
orderDetails[CurrentRecord].getInnerCustOrdObj();
setInnerFieldText(currentItem);
System.out.println("Current Item" + currentItem);
innerleftpanel.add(internalprevbtn, GBC);
return innerleftpanel;
public JPanel createCustOrdDetailsButtons(){
createbuttonpanel();
buttonpanel.setBackground(TxtfontColor);
externalprevbtn = new JButton(createPreviousButtonIcon());
externalprevbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
getFieldText(CurrentRecord);
externalnextbtn.setEnabled(true);
if(CurrentRecord == 1){
externalprevbtn.setEnabled(false);
if(CurrentRecord > 0){
--CurrentRecord;
setFieldText(CurrentRecord);
System.out.println("Current Record " + CurrentRecord);//Checking RECORD_NUM
buttonpanel.add(externalprevbtn);
addrecordbtn = new JButton("Add Record", createAddButtonIcon());
addrecordbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
try{
MaxRecord = readRecordNumber();
MaxRecord++;
CurrentRecord = MaxRecord;
orderDetails[CurrentRecord] = new CustOrdObject();
writeRecordNumber(MaxRecord);
MaxItems = 1;
innerCustOrdObj[MaxItems] = new InnerCustOrdObject();
//--<BEGINNING>--Clear Fields-------------------------------------------------------//
CustIDTxt.setText("");
CustOrderIDTxt.setText(""+MaxRecord);
//Get today's date
Date todaydate = new Date();
OrderedDateTxt.setText(""+simpleDF.format(todaydate));
ItemNumberTxt.setText("");
UnitPriceTxt.setText("");
QuantityReqTxt.setText("");
TotPriceTxt.setText("");
GrandTotTxt.setText("");
//--<END>--Clear Fields-------------------------------------------------------------//
externalnextbtn.setEnabled(false);
externalprevbtn.setEnabled(true);
System.out.println(MaxRecord);
} catch(Exception ec){ec.printStackTrace();}
buttonpanel.add(addrecordbtn);
savebtn = new JButton("Save Data", createSaveButtonIcon());
savebtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
setFieldText(CurrentRecord);
setInnerFieldText(MaxItems);
writeOrder();
writeRecordNumber(MaxRecord);
System.out.println(CurrentRecord);
System.out.println(MaxRecord);
buttonpanel.add(savebtn);
java.net.URL imageURL_AddRowIcon = CommonFeatures.class.getResource("Icons/edit_add.png");
ImageIcon AddRowIcon = new ImageIcon(imageURL_AddRowIcon);
additemreqbtn = new JButton("Add Item", AddRowIcon);
additemreqbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
try{
//--<BEGINNING>--Clear Fields-------------------------------------------------------//
ItemNumberTxt.setText("");
UnitPriceTxt.setText("");
QuantityReqTxt.setText("");
TotPriceTxt.setText("");
//--<END>--Clear Fields-------------------------------------------------------------//
//CurrentRecord = MaxRecord;
MaxItems++;
innerCustOrdObj[MaxItems] = new InnerCustOrdObject();
System.out.println("Max Items "+MaxItems);
currentItem = MaxItems;
orderDetails[CurrentRecord].setMaxItems(MaxItems);
///setInnerFieldText(currentItem);
internalnextbtn.setEnabled(false);
internalprevbtn.setEnabled(true);
} catch(Exception ec){ec.printStackTrace();}
buttonpanel.add(additemreqbtn);
externalnextbtn = new JButton(createNextButtonIcon());
externalnextbtn.addActionListener(new ActionListener(){
public void actionPerformed(ActionEvent evt){
getFieldText(CurrentRecord);
externalprevbtn.setEnabled(true);
if(CurrentRecord < MaxRecord){
++CurrentRecord;
setFieldText(CurrentRecord);
System.out.println(CurrentRecord);//Checking RECORD_NUM
if(CurrentRecord == MaxRecord){
externalnextbtn.setEnabled(false);
buttonpanel.add(externalnextbtn);
gotorecordbtn = new JButton("Go To Record", createGotoButtonIcon());
gotorecordbtn.addActionListener(new ActionListener() {
public void actionPerformed(ActionEvent evt){
* The text from the GotorecordTxt textfield will be taken and assigned
* to a temporary integer variable called Find.
int Find = Integer.parseInt(CustOrderIDTxt.getText());
for(int j=1; j <= MaxRecord; j++){
* Using a for loop, each record can be read using the readCustRecord
* method.
getFieldText(j);
* An if condition is utilized to check whether the temporary stored variable, Find,
* matches a field in a record. If this record is found, then using the RecordExists
* which was declared at the top, either a true or false statement can be assigned
* If the record exists, then a true statement will be assigned, if not a false
* statement will be assigned.
if(orderDetails[j].getCustOrderID() == Find){
RecordExists = true;
break;
}else{
RecordExists = false;
if(RecordExists == false){
* If the RecordExists is assigned a false statement, then a message will be
* displayed to show that the record does not exist.
JOptionPane.showMessageDialog(null, "Record Does Not Exist!", "Error Message", JOptionPane.ERROR_MESSAGE, createErrorIcon());
}else{
getFieldText(Find);
buttonpanel.add(gotorecordbtn);
return buttonpanel;
//TODO
public void setFieldText(int orderID){//TODO
orderDetails[orderID].setCustID(Integer.parseInt(CustIDTxt.getText()));
orderDetails[orderID].setCustOrderID(Integer.parseInt(CustOrderIDTxt.getText()));
orderDetails[orderID].setOrderDate(OrderedDateTxt.getText());
orderDetails[orderID].setInnerCustOrdObj(innerCustOrdObj);
orderDetails[orderID].setMaxItems(MaxItems);
setInnerFieldText(currentItem);
orderDetails[orderID].setGrandTotal(Float.parseFloat(GrandTotTxt.getText()));
public void setInnerFieldText(int currentItem){//TODO
innerCustOrdObj[currentItem] = new InnerCustOrdObject();
innerCustOrdObj[currentItem].setMaxItems(MaxItems);
innerCustOrdObj[currentItem].setItemNumber(Integer.parseInt(ItemNumberTxt.getText()));
innerCustOrdObj[currentItem].setUnitPrice(Float.parseFloat(UnitPriceTxt.getText()));
innerCustOrdObj[currentItem].setQuantityRequired(Integer.parseInt(QuantityReqTxt.getText()));
innerCustOrdObj[currentItem].setTotalPrice(Float.parseFloat(TotPriceTxt.getText()));
public void getFieldText(int orderID){
CustIDTxt.setText(Integer.toString(orderDetails[orderID].getCustID()));
CustOrderIDTxt.setText(Integer.toString(orderDetails[orderID].getCustOrderID()));
OrderedDateTxt.setText(""+orderDetails[orderID].getOrderDate());
currentItem = orderDetails[orderID].getMaxItems();
orderDetails[orderID].getInnerCustOrdObj();
System.err.println("currentItem" + currentItem);
//getInnerFieldText(currentItem);
GrandTotTxt.setText(Float.toString(orderDetails[orderID].getGrandTotal()));
public void getInnerFieldText(int currentItem){
ItemNumberTxt.setText(Integer.toString(innerCustOrdObj[currentItem].getItemNumber()));
UnitPriceTxt.setText(Float.toString(innerCustOrdObj[currentItem].getUnitPrice()));
QuantityReqTxt.setText(Integer.toString(innerCustOrdObj[currentItem].getQuantityRequired()));
TotPriceTxt.setText(Float.toString(innerCustOrdObj[currentItem].getTotalPrice()));
public void writeOrder(){//TODO
try {
objOut = new ObjectOutputStream(new FileOutputStream(OrderDetailsFile));
objOut.writeObject(orderDetails);
System.out.println("WORKING!");
objOut.flush();
objOut.close();
} catch (IOException e) {
e.printStackTrace();
public Object readOrder(){
Object temporaryObj;
try{
objIn = new ObjectInputStream(new FileInputStream(OrderDetailsFile));
temporaryObj = objIn.readObject();
CustOrdObject[] blah = (CustOrdObject[]) temporaryObj;
/* System.out.println("Outer: "+blah[1].getCustID());
InnerCustOrdObject[] whee = blah[1].getInnerCustOrdObj();
System.out.println("Inner: "+whee[1].getItemNumber());*/
objIn.close();
System.out.println("Read Worky!");
return temporaryObj;
}catch(Exception e){
e.printStackTrace();
System.out.println("Read No Worky!");
return null;
public void writeRecordNumber(int MaxRecord){
try{
objOut = new ObjectOutputStream(new FileOutputStream(OrdRecordNumStore));
objOut.writeObject(MaxRecord);
System.out.println("WORKING!");
objOut.flush();
objOut.close();
}catch(Exception e){e.printStackTrace();}
public int readRecordNumber() {
try {
objIn = new ObjectInputStream(new FileInputStream(OrdRecordNumStore));
int temporaryObj = Integer.parseInt(objIn.readObject().toString());
objIn.close();
System.out.println("Read Number Worky!");
return temporaryObj;
} catch (Exception e) {
e.printStackTrace();
System.out.println("Read Number No Worky!");
return -1;
}Message was edited by:
Kilik07 -
problem with vista and 5. i install my old audigy 2 zs exp pro with DTT2500 speaker
In my new pc.
i install vista 64 and SBAX_PCDRV_LB_2_8_000 driver from creative site.
when i go to control panel/sound and test the 5. surrund ' iget only the two front speaker.
why is that?
i try to play a song from vista folder "Distance" and i get all 5 +sub to play.
do i miss something?
is the test worg and with another test i can get all spedajer to work or the driver is not good?
thanks for all you help
last update...
i can get 4 speaker when i use the fourpoint mode on the desktop theather 5. dtt2500 digital,
but in movie mode i get only 2 front speaker.
i use the digital out from the sound blaster.
Message Edited by raflevi on 05-4-2009 02:38 [email protected]My apologies about not explaining further about disabling SPDIF passthrough. See the steps below to enable DDL encoding.
***Before proceeding please make sure that you've purchased, installed and activated the DDL pack***
. Open Creative Audio Console, go to the Decoder tab to disable driver level encoding and enable SPDIF passthrough (this is done by selecting SPDIF passthrough or any similar option that enable the use of an external decoder) instead of using the built-in decoders.
2. Open up your playback devices window (right click on the speaker icon on the taskbar and select playback devices) and set analog speakers (not SPDIF) as your default device. This is VERY IMPORTANT step, or else you get the "the device is busy" error when enbaling DDL encoding.
3. In the Audio Console, select the Encoder tab and enable DLL encoding.
Note:
When DDL encoding is enabled, it makes exclusi've use of your SPDIF connection so, no passthrough is possible. The default output format when using DDL encoding is 48KHz/6 bits. If you make use of any AC3 audio filters (such as ac3filter/others included in codec packs/media player softwares) when DLL encoding is enabled, then please change their output device to analog speakers instead of SPDIF.
To use back SPDIF passthrough (when playing back media with a pre-encoded audio source), open up Audio Console and disable DDL encoding and in the Playback Devices window change the default device to SPDIF. If you make use of any AC3 audio filters (such as ac3filter/others included in codec packs/media player softwares) then please change their output device back to SPDIF. You may also wish to change back your output format to 92KHz/24 bits (right click on SPDIF and select properties -> Advanced tab).
raflevi wrote:
when you said to install ddl? pack you mean the "[url="http://buy.soundblaster.com/_creativelabsstore/cgi-bin/pd.cgi?page=product_detail&category=Software&pid=F 2222SR6PAKH5DGY6SD">Dolby Digital Li've Pack - SB Audigy Series[/url] "?
thanks again for all your help.
i wanted to use the 5. function mostly for games
Yes... also please see the link in my previous post.
Hope this answers your questions. -
Problem with sqlldr and commit
Hi,
i have a problem with sqlldr and commit.
I have a simple table with one colum [ col_id number(6) not null ]. The column "col_id" is primary key in the table. I have one file with 100.000 records ( number from 0 to 99.999 ).
I want load the file in the table with sqlldr ( sql*loader ) but i want commit only if all records are loaded. If one record is discarded i want discarded all record of file.
The proble is that in coventional path the commit is on 64 row but if i want the same records of file isn't possible and in direct path sqlldr disable primary key :(
There are a solutions?
Thanks
I'm for the bad EnglishThis is my table:
DROP TABLE TEST_SQLLOADER;
CREATE TABLE TEST_SQLLOADER
( COL_ID NUMBER NOT NULL,
CONSTRAINT TEST_SQLLOADER_PK PRIMARY KEY (COL_ID)
This is my ctlfile ( test_sql_loader.ctl )
OPTIONS
DIRECT=false
,DISCARDMAX=1
,ERRORS=0
,ROWS=100000
load data
infile './test_sql_loader.csv'
append
into table TEST_SQLLOADER
fields terminated by "," optionally enclosed by '"'
( col_id )
test_sql_loader.csv
0
1
2
3
99999
i run sqlloader
sqlldr xxx/yyy@orcl control=test_sql_loader.ctl log=test_sql_loader.log
output on the screen
Commit point reached - logical record count 92256
Commit point reached - logical record count 93248
Commit point reached - logical record count 94240
Commit point reached - logical record count 95232
Commit point reached - logical record count 96224
Commit point reached - logical record count 97216
Commit point reached - logical record count 98208
Commit point reached - logical record count 99200
Commit point reached - logical record count 100000
Logfile
SQL*Loader: Release 11.2.0.1.0 - Production on Sat Oct 3 14:50:17 2009
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
Control File: test_sql_loader.ctl
Data File: ./test_sql_loader.csv
Bad File: test_sql_loader.bad
Discard File: none specified
(Allow all discards)
Number to load: ALL
Number to skip: 0
Errors allowed: 0
Bind array: 100000 rows, maximum of 256000 bytes
Continuation: none specified
Path used: Conventional
Table TEST_SQLLOADER, loaded from every logical record.
Insert option in effect for this table: APPEND
Column Name Position Len Term Encl Datatype
COL_ID FIRST * , O(") CHARACTER
value used for ROWS parameter changed from 100000 to 992
Table TEST_SQLLOADER:
100000 Rows successfully loaded.
0 Rows not loaded due to data errors.
0 Rows not loaded because all WHEN clauses were failed.
0 Rows not loaded because all fields were null.
Space allocated for bind array: 255936 bytes(992 rows)
Read buffer bytes: 1048576
Total logical records skipped: 0
Total logical records read: 100000
Total logical records rejected: 0
Total logical records discarded: 0
Run began on Sat Oct 03 14:50:17 2009
Run ended on Sat Oct 03 14:50:18 2009
Elapsed time was: 00:00:01.09
CPU time was: 00:00:00.06
The commit is on 992 row
if i have error on 993 record i have commit on first 992 row :(
Edited by: inter1908 on 3-ott-2009 15.00 -
Problem with JFrame and busy/wait Cursor
Hi -- I'm trying to set a JFrame's cursor to be the busy cursor,
for the duration of some operation (usually just a few seconds).
I can get it to work in some situations, but not others.
Timing does seem to be an issue.
There are thousands of posts on the BugParade, but
in general Sun indicates this is not a bug. I just need
a work-around.
I've written a test program below to demonstrate the problem.
I have the problem on Solaris, running with both J2SE 1.3 and 1.4.
I have not tested on Windows yet.
When you run the following code, three JFrames will be opened,
each with the same 5 buttons. The first "F1" listens to its own
buttons, and works fine. The other two (F2 and F3) listen
to each other's buttons.
The "BUSY" button simply sets the cursor on its listener
to the busy cursor. The "DONE" button sets it to the
default cursor. These work fine.
The "SLEEP" button sets the cursor, sleeps for 3 seconds,
and sets it back. This does not work.
The "INVOKE LATER" button does the same thing,
except is uses invokeLater to sleep and set the
cursor back. This also does not work.
The "DELAY" button sleeps for 3 seconds (giving you
time to move the mouse into the other (listerner's)
window, and then it behaves just like the "SLEEP"
button. This works.
Any ideas would be appreciated, thanks.
-J
import java.awt.BorderLayout;
import java.awt.Cursor;
import java.awt.event.ActionEvent;
import java.awt.event.ActionListener;
import javax.swing.JButton;
import javax.swing.JFrame;
import javax.swing.JPanel;
import javax.swing.SwingUtilities;
public class BusyFrameTest implements ActionListener
private static Cursor busy = Cursor.getPredefinedCursor (Cursor.WAIT_CURSOR);
private static Cursor done = Cursor.getDefaultCursor();
JFrame frame;
JButton[] buttons;
public BusyFrameTest (String title)
frame = new JFrame (title);
buttons = new JButton[5];
buttons[0] = new JButton ("BUSY");
buttons[1] = new JButton ("DONE");
buttons[2] = new JButton ("SLEEP");
buttons[3] = new JButton ("INVOKE LATER");
buttons[4] = new JButton ("DELAY");
JPanel buttonPanel = new JPanel();
for (int i = 0; i < buttons.length; i++)
buttonPanel.add (buttons);
frame.getContentPane().add (buttonPanel);
frame.pack();
frame.setVisible (true);
public void addListeners (ActionListener listener)
for (int i = 0; i < buttons.length; i++)
buttons[i].addActionListener (listener);
public void actionPerformed (ActionEvent e)
System.out.print (frame.getTitle() + ": " + e.getActionCommand());
if (e.getActionCommand().equals ("BUSY"))
frame.setCursor (busy);
else if (e.getActionCommand().equals ("DONE"))
frame.setCursor (done);
else if (e.getActionCommand().equals ("SLEEP"))
frame.setCursor (busy);
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.print (" finished");
else if (e.getActionCommand().equals ("INVOKE LATER"))
frame.setCursor (busy);
SwingUtilities.invokeLater (thread);
else if (e.getActionCommand().equals ("DELAY"))
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (busy);
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.print (" finished");
System.out.println();
Runnable thread = new Runnable()
public void run()
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.println (" finished");
public static void main (String[] args)
BusyFrameTest f1 = new BusyFrameTest ("F1");
f1.addListeners (f1);
BusyFrameTest f2 = new BusyFrameTest ("F2");
BusyFrameTest f3 = new BusyFrameTest ("F3");
f2.addListeners (f3); // 2 listens to 3
f3.addListeners (f2); // 3 listens to 2I've had the same problems with cursors and repaints in a swing application, and I was thinking of if I could use invokeLater, but I never got that far with it.
I still believe you would need a thread for the time consuming task, and that invokeLater is something you only need to use in a thread different from the event thread. -
Problem with installing and running some applications or drivers
When installing and installing some items, towards the end of the installation I get this message:
/System/Library/Extensions/comcy_driver_USBDevice.kext
*was installed improperly and cannot be used. Please try reinstalling it or contact product's vendor for update*
The end result is that some things do not seem to work properly, such as my HP printer. Would anybody have any ideas on how to fix this problem?Thank you for your response. Originally, I had a problem with Airport and ended up reinstalling Snow Leopard. Since then, when downloading upgrades etc, such as HP printer drivers, iTunes etc., towards the end of the download when its running the script, I get this message: /System/Library/Extensions/comcy_driver_USBDevice.kext
+was installed improperly and cannot be used. Please try reinstalling it or contact product's vendor for update+
Sometimes, the download hangs and is unable to complete. The main problem I've encountered so far with an application is when I use the printer to scan an image via Preview, it's blank: there's nothing there. -
Problems with outlook and address book contacts: my outlook contacts had around 3,000 entries. Outlook duplicated entries and have now 340,000. I reinstalled microsoft office and, thus, outlook, and reinstalled mac OS X system and applications. While I managed to delete outlook contacts so that I can re-sync with my blackberry, the contacts at Mac Address Book were not deleted and still have over 340,000 entries. I do not mind deleting all contacts since I have back up, but I have not been able to delete them. Also, when I go at Address Book and try to delete or merge duplicated entries, the system takes forever and never ends because of such large amount of entries. Worse, when I do so I run out of RAM memory.
My Macbook pro is just 2 months old.
What should I do? Is there a way to delete my Mac Address Book without having the problem above?
Many thanks
Regiszlatan24 wrote:
For solving out troubles connected with corrupted or lost address book you may use address book recovery. It owns various features such as restoring wab files, it working under any Windows OS. The utility has modern and easy to use interface due to almost every experienced users.
If it is a windows problem it's not going to run on the OP's MacBook Pro -
Problems with Safari and Firefox (HTTP?)
Problems with Safari and Firefox (HTTP?)
On a laptop G4, 10.5.8 and Safari 5.02 I experience the following:
On the account of my oldest daughter everything works fine, i.e. wireless internet works and no problems with mail or safari.
On the same laptop, on the account of my other daughter, the wireless is OK, she can mail etc. But safari nor firefox works. It says: can’t find server (whatever site) and in the activity window it looks if safari tries to open files (in the safari preferences-folder) in stead of http. Same applies to Firefox, so maybe it has more to do with HTTP in general?
What goes wrong? What to do? I tried the following on the host terminal (tips from Apple)
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false
and
defaults delete com.apple.safari WebKitDNSPrefetchingEnabled
but that did not help,
NanneI'm still wondering why it happens now at this moment in time...
PC does seem to be a bit odd & inconsistent, the few times I've tested with it, at least so far as we content filtering goes; and if I remember rightly, you're not the first to report previously ok settings suddenly preventing some or all internet until pc is switched off altogether.
It may work when re-enabled -
Haven't been able to use pages for a while. Keep getting following message. Have tried reinstalling iWork, but no luck. Same problems with Keynote and Numbers/
Have you moved Pages from its installed location? Or just dragged a copy to your current system?
It can't find some of its resources apparently.
Peter -
Problem with DMGs and error: "No Mountable File Systems"
Problem with DMGs and error: "No Mountable File Systems"
The files are not corrupt. The problem is occurring with all DMGs that are apparently formatted in MS-DOS FAT16. No the file will not mount with Disk utility or any other disk mounter programs I have found.
This is now the second time this occurred and now effects my MBP and my iMac. First time i spent days with Apple support and the only solution was ultimately back up the data, reformat the HD, start over from scratch and reload everything. That lasted about a month before the problem resurfaced and is now an issue on both iMac and MBP.
I tried to identify all the programs I installed immediately before the error, as I am convinced it is the result of a software conflict.
Recent programs includes:
1) upgrading from Parallels 5.5 to 6.0 on both machines.
2) using an HP secure II usb drive and setting up a secure disk.
3) installing new itunes 10
4) new update to Flip For Mac.
The files affected are downloaded dmgs, including personal brain and google earth, both which are formatted in FAT16.
Any help or thoughts? Apple has now spent hours trying and they say i now have to reformat and wipe and start over. That is unacceptable and based on pasted experience the problem is likely to repeat itself. having to wipe and rebuild a HD ever month is not an solution. i need to fid the root problem.
In the meantime, anyone got a real solution on how to extract the data for a DMG using a different method?
Message was edited by: remaiaWhere you able to find the solution, i am having the same problem, all was fine till i install some programs only same one i saw did we both did was flip4mac i uninstalled it but the problem is still there, i also restored and erased the hardrive but im not up to doing that all over again. If you found anything out let me know i would greatly appreciate it
-
Problem with Send and Receive Emal In SAP System
Hi gurus!
I have a following quote:
Dear !
I have a problem with send and receive email in SAP system following :
I want to test send and receive email in local network at my company. I
had two server
Server 1 : I setup Exchange Mail Server 2007 with domain controller is
fes.com
Server 2 : I setup SAP ERP ECC 6.0
On Server 1 : I created 2 account ( u1Afes.com and u2Afes.com ) and then I tested send and receive email between u1 and u2 in local network through Microsoft Outlook 2007 -> OK
and then
On Server 2: I had configured send and receive email on SAP system
through tcode SBWP, SCOT and SOST as Note 455140 - "Configuration of
e-mail, fax, paging or SMS using SMTP"
for example :
I logged in SAP system with user Basis01 (with email u1Afes.com ) -> then,using tcode SBWP -> new message -> send to u2Afes.com with Internet Mail type and then status message with green light -> sending ok
and then I have used Microsoft Outlook 2007, I logged with account u2 ->check email -> Ok. I saw message which send from u1
Finally, My problem is how can receive mail in SAP system without using Microsoft Outlook
For example:
Login system SAP with Basis01 account (with u1Afes.com ) -> tcode SBWP ->New Message -> send to u2Afes.com
and then
Login system SAP with Basis02 account (with u2Afes.com ) -> tcode ??? ->
To receive email from Basis01 (with u1Afes.com )
Please help me now
Thanks
I replace "@" with "A" because of banning email of this forum.
This quote is about sending email in local network. And we can't receive any email from the outside email address. Addition if I wanna send email to internal email in Internet (we've just tried with email address in local network) What should I config in SAP and Exchange ?
By the way, Is SAP Server IP added to Relay Agent for sending or receiving mail ?
Regards
An NLP
Edited by: An NLP on Apr 6, 2010 7:03 PMHi,
This problem is a classic problem of mail routing via Exchange. Exchange like most mail servers use the domain part of the email address as a means to route mails. So I will make an assumption that your main company mail addrss is "User @ fes.com".
So when you send a mail to the "User @ fes.com mail" address the mail is delivered to your Outlook mail address as this is the default route for company.
(Q) So how do you get your Exchange server to relay the mail into the sending SAP system?
(A) The easiest way would be to setup and unique mail domain for your SAP system. I always recommend "user @ client.sid.company.com" which in your case would be "u1 @ 100.PRD.fes.com". You can then instruct Exchange to send any emails addressed to 100.PRD.fes.com domain to your SAP system. Also using this format of address you can configure multiple mail connections into multiple SAP systems.
(A) Another answer would be to enter the "Full" email address (LOcal and Domain part of address) into the routing rule for Exchange e.g. "U1 @ fes.com" so that all emails addressed to this user will be delivered into SAP. However this method requires a lot of Admin as you will have to update Exchange with ALL email address that need to receive emails. Also if your corporate mail address is "U1 @ fes.com" then all mails will be forwarded to SAP.
I would definitely NOT recommend this method but the decision is up to you.
P.S. The IP address of the SAP system is entered into the mail header of the email. This is standard practice in SMTP relay. You can suppress this header in Exchange
Hope this helps
Michael -
Problem with Speaker and Headset in Windows Vista
Hi, I just got my Macbook Pro 13" and having problem with speaker and headset when working with Windows Vista (I have installed the driver from bootcamp). The sound very weak if I play music from Itunes or youtube even the volume already full and if i put my headset the sound not coming out. Is there anyone can help me to solve this problem?
Regards,EdwinWhen you post about Windows / Boot Camp, in Mac Pro (workstation) forum where others with a MacBOOK would be more likely to have same hardware configuration, and you won't find Windows drivers on Apple downloads. More like at
http://www.guru3d.com or other sites, or go to RealTek (if that is the type of audio you have). -
Problem with trigger and entity in JHeadsart, JBO-25019
Hi to all,
I am using JDeveloper 10.1.2 and developing an application using ADF Business Components and JheadStart 10.1.2.27
I have a problem with trigger and entity in JHeadsart
I have 3 entity and 3 views
DsitTelephoneView based on DsitTelephone entity based on DSIT_TELEPHONE database table.
TelUoView based on TelUo entity based on TEL_UO database table.
NewAnnuaireView based on NewAnnuaire entity based on NEW_ANNUAIRE database view.
I am using JHS to create :
A JHS table-form based on DsitTelephoneView
A JHS table based on TelUoView
A JHS table based on NewAnnuaireView
LIB_POSTE is a :
DSIT_TELEPHONE column
TEL_UO column
NEW_ANNUAIRE column
NEW_ANNUAIRE database view is built from DSIT_TELEPHONE database table.
Lib_poste is an updatable attribut in TelUo entity, DsitTelephone entity, NewAnnuaire entity.
Lib_poste is upadated in JHS table based on TelUoView
I added a trigger on my database shema « IAN » to upadate LIB_POSTE in DSIT_TELEPHONE database table :
CREATE OR REPLACES TRIGGER “IAN”.TEL_UO_UPDATE_LIB_POSTE
AFTER INSERT OR UPDATE OFF lib_poste ONE IAN.TEL_UO
FOR EACH ROW
BEGIN
UPDATE DSIT_TELEPHONE T
SET t.lib_poste = :new.lib_poste
WHERE t.id_tel = :new.id_tel;
END;
When I change the lib_poste with the application :
- the lib_poste in DSIT_TELEPHONE database table is correctly updated by trigger.
- but in JHS table-form based on DsitTelephoneView the lib_poste is not updated. If I do a quicksearch it is updated.
- in JHS table based on NewAnnuaireView the lib_poste is not updated. if I do a quicksearch, I have an error:
oracle.jbo.RowAlreadyDeletedException: JBO-25019: The row of entity of the key oracle.jbo. Key [null 25588] is not found in NewAnnuaire.
25588 is the primary key off row in NEW_ANNUAIRE whose lib_poste was updated by the trigger.
It is as if it had lost the bond with the row in the entity.
Could you help me please ?
Regards
LaurentThe following example should help.
SQL> create sequence workorders_seq
2 start with 1
3 increment by 1
4 nocycle
5 nocache;
Sequence created.
SQL> create table workorders(workorder_id number,
2 description varchar2(30),
3 created_date date default sysdate);
Table created.
SQL> CREATE OR REPLACE TRIGGER TIMESTAMP_CREATED
2 BEFORE INSERT ON workorders
3 FOR EACH ROW
4 BEGIN
5 SELECT workorders_seq.nextval
6 INTO :new.workorder_id
7 FROM dual;
8 END;
9 /
Trigger created.
SQL> ALTER SESSION SET NLS_DATE_FORMAT = 'DD-MON-YYYY HH24:MI:SS';
Session altered.
SQL> insert into workorders(description) values('test1');
1 row created.
SQL> insert into workorders(description) values('test2');
1 row created.
SQL> select * from workorders;
WORKORDER_ID DESCRIPTION CREATED_DATE
1 test1 30-NOV-2004 15:30:34
2 test2 30-NOV-2004 15:30:42
2 rows selected.
Maybe you are looking for
-
CFOP de Importação e não informado dados da DI
Ola! Há mudanças no processo de entrada de documentos de importação para NF-e de layout XML 3.10? A NF-es nós emitidas desde 3.10 obter o erro Rejeicao: 525 CFOP de Importação e não informado dados da DI. Cholen
-
Need a good Photo Gallery Extension
Setting up a photo gallery with hundreds of shots. Would like an extension that give more choices for Dreamweaver CS3. Would like to create pop-ups from thumbnails from a folder of photos in a batch medthod without having to do each individually.
-
Add-dayTimeDuration-to-dateTime
Hi, Could you please tell me why the second assignment is not working? I have no errors but the variable var2 is empty. <variable name="var1" type="xsd:dateTime"/> <variable name="var2" type="xsd:dateTime"/> <copy> <from expression="xp20:current-date
-
Airport Problems after Security Update 2007-004
Ever since I've installed Security Update 2007-004 my Airport connection has been dropping about every 15 to 30 minutes. Sometimes Airport will stay connected but will stop working until I renew my DHCP lease (I get the same IP though). When it drops
-
Opentype Feature Bug in InDesign CS6 until CC14.2
Hi, my name is Sami Mandelbaum and I am doing a Hebrew font with a simple opentype feature (final position) Hebrew has 5 letters that changed format when they are the last letter of the word (in the left, hebrew is a RTL language) I am doing the the