Problems with Smart Wireless Headset Pro after upgrading my Xperia Sola to ICS

Just want to let the community, and Sony, know that since I "upgraded" my Xperia Sola to ICS, the Text to Speech on my Smart Wireless Headset Pro is not functioning. It used to work just fine when I had Gingerbread on my phone, but when I upgraded to ICS, the Text to Speech voice is not output on the headset, but on the phone, on the call speaker... Hope this bug gets fixed soon.
Maybe someone already knows of a solution?
Thanks in advance.

There is a new update available for the Smart Wireless headset pro, MW1 (0.1.C.0.3).
Which software version are you running your MW1 on?
If you don't have the latest I suggest that you use SUS to update your software.
http://www.sonymobile.com/gb/tools/update-service/
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Similar Messages

Has anyone been having problems with bluetooth in Macbook PRO after upgrading to Mavericks?

Hello,
Ever since I upgrade my 13inch (early 2011) Macbook PRO to OS X Mavericks I have been experiencing problems with bluetooth connectivity. Suddenly my Magic Mouse stops working and I cannot connect it back. Also I try turning off the bluetooth function but is not possible. The only workaround I have found is to restart the system.
I appreciate any help.

Look in the More Like This box to the right of your post.

Smart Wireless Headset pro won't start

Hi,
I have a Smart Wireless Headset pro, yestarday it powered it self off while I was listening to music, since then I can't power it on.
I've tryed to charge it, to hold down the power for few seconds.
Nothing works, it dead now.
Any one have an idia how to fix it?

Try these steps.
1 Make sure the headset is turned off.
2 Press and hold the power key for 15 seconds.
3. If nothing happens, put the charger in headset and do it again.
4. Hold the key until Factory reset? appears on the headset display.
3 Press the Next key or the Previous key to
select , then press the Select key.
If the problem still remains it sounds like it needs to be examined and fixed at an repair center. Contact your local support team for more info.
http://www.sonymobile.com/global-en/support/contact-us/contact-info/
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Smart Wireless Headset Pro connection to laptop

Good afternoon all,
I'm trying to connect my wireless headset to my business laptop...
But when connecting, windows (vista) wants to have drivers for the headset.
Now my question is: Where to get these drivers? Or is this even possible what I want?
Thanks!

There are no special drivers for Smart Wireless Headset pro, it uses standard Bluetooth drivers. Check that your Bluetooth stack is using the latest firmware version.
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Problem with connecting to free wifi after upgrading to Windows 8.1 from Windows 8

Hi
I had problems with connecting to free Wifi after upgrading my PC(Notebook) to Windows 8.1 from Windows 8. As I travel a lot within europe, I am used to being able to connect to Free Wifi(those that dont need a key or password to enter) but soon after downloading
Windows 8.1 I almost never was able to do this. I'd always get «LIMITED» even though the signal was strong.This was so fustrating,so much so that I reset my PC to clear it of Windows 8.1 and am now back to Windows 8.This is a shame because I was really liking
using Windows 8.1 and if not for this problem(which is a big one) I'd still be using it. If I download Windows 8.1 again from the Windows store what is the probability that I'll have the same problems?
Thanks Portozzygirl

More often than not when a device isn't working it is because the driver has become corrupted. Re-installing a fresh copy should help
http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isnt-working-properly?SignedIn=1
http://captaindbg.com/how-to-update-drivers-on-windows-7/ (works on win 8 too)
Wanikiya and Dyami--Team Zigzag

Hello, I have a problem with my mac book pro after running the battery dead on a game. The display has shrunk leaving two black margins on either side. What to do ?

Hello, I have a problem with my mac book pro after running the battery dead on a game. The display has shrunk leaving two black margins on either side. What to do ?

Go to System Preferences>Displays and set the resolution to "Best for this computer" (or something to that effect).
Clinton

Problem with WCS Audit status missmatch after upgrade

We had problem with wcs Audit status missmatch after upgrade to 7.0.164.3 WLC : 6.0.188.0.
how I can fix the problem?

Hi,
Try pinging the WCS from the WLC and vice versa and then try again to refresh config from controllers.. then follow the below if its still not happening..
Please forwrd the trace level logs from the WCS (Specifically WCS0.0.TXT logs) while recreating the issue!!
Regards
Surendra

Are you having problems with the Lacie external drive after upgrading to the new operating system

Are you having problems with the Lacie external drive after upgrading to OS X Mavericks?

See here for everyone discussing the issue you are having:
https://discussions.apple.com/thread/5475136?tstart=0

Problems with result area in workbooks after upgrade to BW 3.5

Hi,
we are experiencing some problems with our <b>workbooks</b> after the upgrade to BW 3.5. When refreshing all queries in a workbook (that was there before 3.5) without selecting a specific query we get the message <b>'Result area</b> cannot be found, specify a new one'. After selecting, the message appears again in an infinite loop.
Has anybody had similar problems and has found a solution for this?
Thanks,
EMS

Hi,
I am having that message, always if I delete a Sheet which contains an embeded query.
Even the sheet is deleted, the SAPBEX has information of all the embeded queries, and tries to find the Result area to put the data.
To find out if this is your case as well,
select an empty cell in a Sheet and continue like that, until all the embeded queries are been displayed.
Regards
Vasso
Message was edited by: VASSILIKI SIAGRI

I have problems with my Mac Book Pro after I upgraded it

I upgraded my Mac Book Pro from MAC OS X 10.9 to Yosemite version a week ago, and now it doesn´t start

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Problem with scanning in Photoshop CS6 after upgrading to Mountain Lion

After upgrading to latest version of Mountain Lion i've got a problem with scanning directly into Photoshop CS6.
on the previous Lion version when I wanted to scan something, i just opened Photoshop -> File -> Import -> images from device
then a new window opened up the ImageCapture app where I could choose the device I wanted to use, and then I selected the scanner (Canon CanoScan 8400F) and I could scan directly into photoshop.
Now with Mountain Lion when I do the exact same thing, it opens a window, but it's impossible to select any device, as the new window is just a plain white window, with 2 buttons on top to rotate something that isn't there. (text is in dutch, cause I'm from the Netherlands)
hope someone can help me out.
I can scan with the use of the ImageCapture app without problems and then save that picture and open it in Photoshop, but it has worked before, so am I doing something wrong? or is this just a little bug
thnx in advance for the help

I’m having the same problem with my Epson Perfection 3200 Photo scanner and Adobe Photoshop CS6. It does the initial overview scan then I get the same blank window as BigNoud shows above. I've done a Software Update and have also updated OSX to 10.8.1.
I know for the Epson you can get a Mountain Lion compatible scan software from SilverFast for about $35.00 as an upgrade here.
I haven't gone that route yet as I don't want to give up any more money for my Apple/Adobe experience.
Any help would be appreciated.

Problem with ADF Security / SQL Authenticator after upgrade to 11.1.1.6

Hi,
We have an ADF application built with JDeveloper 11.1.1.2 that's been in production for a couple of years. Now we are in the process of upgrading to 11.1.1.6 so I have upgraded WLS and ADF in a test environment and re-deployed the application there. The application uses users and groups from database using SQL Authenticator configured in WLS. This worked fine in the old version but now after the upgrade we can't log in with credentials from the database. I can log in if I add a user to the default authenticator. We didn't touch any of the authenticator settings or security realm configurations during the upgrade. Both authenticators are marked as SUFFICIENT, as they have always been.
Has something changed in the way SQL Authenticator is used since 11.1.1.2? What could be the problem?
Regards,
Joonas

Answering myself here: after recreating the SQL Authenticator and the ADF Security configuration logins are working again. Don't know where the problem was though.

I have problems with the wi-fi connection after upgrading my iPhone to iOS 5- why?

Since upgrading the software on my iPhone 4 to iOS5, I have had all sorts of wi-fi connection problems.
The wireless router I have always used is now usually not detected by my iPhone. It still works on my MacBook and iPad, but not on my iPhone. When it is detected, the connection lasts for a few minutes before cutting out. The signal is also very low.
I have tried the following:
-Restarting the router
-Restarting my iPhone
-Resetting my network settings
-Restoring to factory defaults
-Forgetting the network
-Rejoining the network
-Setting up the connection manually
-Turning off location services on my iPhone (I read in another thread this would help)
I am running out of ideas and I have tried researching this. I found many people with the same problem but no solution for my problem yet.
Does anyone have any ideas, or know whether Apple is planning on fixing this anytime soon? It's a huge disappointment.

I tried this! Somebody suggested it in another thread. It did not work, sadly.

Problems with Camera Raw 6.7 after upgrading to OS 10.8

I've been using Photoshop CS 5 with Camera Raw 6.7 on my MacBook Pro with no issues until I recently upgraded to OS 10.8. Now my Canon CR2 files (shot with a Canon G15) won't open. Does anyone know of a solution or work-around for this problem?

thanks for the prompt response...i appreciate it. according to the link you listed, that's correct. the strange thing is that prior to the upgrad to mac os 10.8.4, photoshop CS5 was working just fine and i was able to open my canon raw files with my current camera raw plug-in version 6.7 which adobe has indicated is the last camera raw update they'll be offering for cs 5
so it's clearly an issue related to the "upgrade" of the os. seems like every solution creates 6 new problems...further evidence for the notion that if it ain't broke don't fix it! thanks again.

Problem with PO text in ME22 after upgrade

Hi,
I face an issue in Purchase Order Text. We have recently done the upgrade from SAP 4.6 C to SAP ECC 6.0. Before upgrade, the users were entering required texts in ME22 transaction for each item and select the check button available. All the text types ticked here are carried forward and printed on the Delivery output.
After upgrade, this tick is removed from all the existing documents and also for the new POu2019s users select this button and save it. But, when they come back and see it in change mode ME22, the tick is not available. Because of this issue, these texts are not printed in delivery outputs now.
I have checked this problem in SAP. No relevant notes are available. Has anyone faced this issue before? Can you please throw some light on the same?
Thanks and Regards
Vijayakrishna

Hi
Please, see these notes
Note 751441 - Consulting: Settings for texts from purchase order
Note 53593 - Q&A - Delivery text from stock transfer order
Note 417883 - Texts from purchase order
and related notes. They talk about how to copy text from PO to delivery (for instance, in SC, STO and so on). It's related with some customizing steps in VOTXN and some VOFM subroutines that perhaps they are lost after the upgrade.
I hope this help you
Regards
Eduardo
Edited by: E_Hinojosa on Aug 24, 2011 10:22 AM

Problems with Smart Wireless Headset Pro after upgrading my Xperia Sola to ICS

Similar Messages

Maybe you are looking for