Problems with the installati​on of LabVIEW 6.1 on Windows 2000!

Windows 2000 crashes while installing LabVIEW 6.1, and the computer is unusable after the installation!

This also happened to me. Hopefully you are attempting to run LabView on a dedicated computer. Ours had "issues" with some of the other software we were running. Here's what we did: We re-imaged the computer (backed up everything and re-loaded the OS). Computer has been up and running excellent ever since. There was a lot of useless software originally on it, we took it all off. If you are able, only run what you need on it. Also, we have found that LabVIEW 6 runs strangely on computers with less than 128 MB of RAM. Our project computer currently has 320 MB of RAM (and 40 GB HD) and it runs perfectly.
Hope this helps. If you have a specific error code, let me know. Otherwise, from what you have posted, I believe this is the answer.

Similar Messages

  • Does anyone have problems with the 7th generation nano not being recognized by windows?

    Just got my nano and although it worked the first time I plugged it in to my laptop, it now can not be recognized by Windows, it is completely dead and will not charge at all...anyone else having this issue?

    Hello Chloe
    Start with the first article below to go over some general hardware troubleshooting to get a charge on your iPod nano. If you get that to turn on and you cannot get it to show up on your computer, then the second article should sort you out.
    iPod nano (7th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS4433
    iPod not appearing in iTunes
    http://support.apple.com/kb/TS3716
    Regards,
    -Norm G.

  • Problem with the RunTimeVer​sion

    hi!
    I have changed some programms in RunTime Version with the LabView
    Application Builder , but I met a problem with the programm
    for the balance, that it can run well under LabView but it shows always
    0 under RunTime Version(wrong!), now I don't know what to do with it,
    could someone help me?
    Thanks!
    Le

    Le,
    Are you saying that the version displayed in the splash screen is "0"? If so, then that is very strange, and about the only thing I could think that could cause that problem would be a modification to a registry entry. Go to Start >> Run on your computer and type "regedit" (without the quotes). Navigate to HKEY_LOCAL_MACHINE >> Software >> National Instruments >> LabVIEW Run-Time and make sure that there isn't a folder there named "0" or that your "Current Version" isn't given as "0". If it is, then you should change it to the appropriate version number.
    If this wasn't your problem, or if the suggestion I gave doesn't fix it, please let me know, and if possible, attach a screen capture to your message so that I will see the problem you are describing.
    I hope t
    his suggestion helps. Thanks for your patience, and have a pleasant day.
    Sincerely,
    Darren Nattinger
    Applications Engineer
    National Instruments
    Darren Nattinger, CLA
    LabVIEW Artisan and Nugget Penman

  • Problem with the importing wizard

    Hei,
    I have a dll which I want to import to the Labview project. So, I decided ti use the import wizard, but when parsing the header file, Labview freezes. I am using a couple of structures (3) and a handle. I have also read that the wizard has problems when dealing with complex data. What would be best solution for adding it to the project? To in a way "unbundle" the struct and then create a many simple variables and then parsed to dll.  (This would be a pain)
    How to deal with the handle or will wizard easy understand that?
    I am really looking for a painless solution  
    thanks for the help

    Can you post the header file for the DLL?
    Through a process of trial and error you could determine which functions causes problems with the wizard (comment out half the functions, attempt to import, repeat) and then manually create the LabVIEW VIs for the troublesome ones. If there aren't too many functions, you could do it all by hand, which isn't that hard if you have some understanding of C (and if you don't, you'll undoubtedly have other problems when the wizard doesn't do the right thing).

  • Help In keithley 2400 VI!!(Problem with the data logging and graph plotting)

    Hi,need help badly=(.
    My program works fine when i run it,and tested it out with a simple diode.The expected start current steps up nicely to the stop current.The only problem is when it ends,i cannot get the data log and the graph,though i already have write code for it.Can someone help me see what's wrong with the code?I've attached the necessary file below,and i'm working with Labview 7.1.
    Thanks in advance!!!
    Attachments:
    24xx Swp-I Meas-V gpib.llb ‏687 KB

    Good morning,
    Without the instrument it might be hard for others to help
    troubleshoot the problem.  Was there a
    specific LabVIEW programming question you had, are you having problems with the
    instrument communication, are there errors? 
    I’d like to help, but could you provide some more specific information
    on what problems you are encountering, and maybe accompany that with a simple
    example which demonstrates the behavior? 
    In general we don’t we will be unable to open specific code and debug,
    but I’d be happy to help with specific questions. 
    I did notice, though, that in your logging VI you have at
    least one section of code which appears to not do anything.  It could be that a small section of code, or
    a wire was removed and the data is not being updated correctly (see pic below).  Is your file being opened properly?  Is the data being passed to the file
    properly?  What are some of the things
    you have examined so far?
    Sorry I could not provide the ‘fix’, but I’m confident that
    we can help.  Thanks for posting, and
    have a great day-
    Message Edited by Travis M. on 07-11-2006 08:51 AM
    Travis M
    LabVIEW R&D
    National Instruments
    Attachments:
    untitled.JPG ‏88 KB

  • Problem with the wifi acquisition

    hello all,
      Actually this problem is just screwing me from so many days.I have one wireless adapter(serial to wifi adapter) and using that adapter i had designed one wifi amplifier which will sense biosignals and transmit wirelessly...Ok.Now i started writing an application in labview (receiver ) so that whatever data wifi amplifier is sending i should receive and store in a file.For that purpose i am using TCP/IP vis of labview.But the problem is with the connection.Actually my labview program is configured as server and it waits for some client to connect whereas wifi amplifier is by default it is in client mode.Can anybody please tell where the problem is and please post any VI for the connection?
    Thanks and regards,
    srikrishna.

    Hi muks,
       Thank you very much for your reply...Actually in my application, i am not using any WLS carrier and NI C series modules.Just i have a wifi amplifier(we need to run some ATI commands for communication).I want to connect using normal TCP\IP vis.Can you please tell me how to do this?

  • I just order 8 calendars from iPhoto and they came to me fine. Now I need to order two more but when I go thru the process I get a message  saying:unable to assemble calendar. There is a probleme with the photo with the file name"(Null)"   more........ .

    Would someone be able to explain to me the following issue with Iphoto?
    I ordered 8 same calendars for my soccer team and received them fine. Although a couple of pictures on it are a little off (out of focus). I need to order two more of the same calendars but when I go thru the process ireceive an error message saying:
    "Unable to to assemble  calendar" There is a problem with the photo with the file name "(Null)" The full resolution version of this photo either cannot be located or is corrupt. Please replace this photo or delete it from your calendar.
    How can  I fine this "corrupt" photo? How did it go thru with the first batch of calendars but won't go thru now?
    Thank you for your help.   

    Apply the two fixes below in order as needed:
    Fix #1
    Launch iPhoto with the Command+Option keys held down and rebuild the library.
    Since only one option can be run at a time start
    with Option #4 and then #1 as needed.
    Fix #2
    Using iPhoto Library Manager  to Rebuild Your iPhoto Library
    1 - download iPhoto Library Manager and launch.
    2 - click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
    3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option.
    4 - In the next  window name the new library and select the location you want it to be placed.
    5 - Click on the Create button.
    Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments.  However, books, calendars, cards and slideshows will be lost. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
    OT

  • I can not upgrade to quicktime 7.7.3 for windows vista.  Error message says there is a problem with the program installer.  Any clue as to how to get around this.

    I can not download quicktime 7.7.3 for windows vista.  The error message says that there is a problem with the windows installer.  Any clues?

    The error message says that there is a problem with the windows installer.
    What's the precise text of the message, please? (There's a few different ones I can think of that you might be getting.)

  • I have a problem with the sync between iTunes and ipad2. I can not see the files in iPad. Help me please.

    I have a problem with the sync between iTunes and ipad2. I can not see the files in iPad. Help me please.

    Cannot see what files ? Music (synced music should appear in the iPod app), films/TV shows (Videos app), documents ... ?

  • Is anyone having a problem with the new iPad (Gen. 3) not staying connected to the charger? It seems to ALWAYS get jiggled loose and no longer be charging. My iPad 1 has no issue but I can't browse Internet w/o new iPad unplugging. Horrible!

    I notice that my new IPad (3rd generation) will not stay connected to the power cord at all, I'm not exagerating, if I plug it in and browse the Internet without fail it will become unplugged and I will have to push the plug back in (Ba-beep). Ive actually grown to despise that sound when you plug your iPhone or iPad in because it reminds me of how much money I spent on something that PHYSICALLY will not charge while I'm using it.
    I know the problem with it holding a charge while in use, I get it, the screen is amazing and it takes a lot to run the display, however, it is unacceptable to me that I can't even keep the thing plugged in while I'm using it. I can not even leave it on my Cal King bed overnight because I will wake up in the morning to find that the plug has been jiggled loose in a corner, so it's still attached but not making a connection thus not being charged. 
    I love the 4GLTE from Verizon and I love the iPad, but I'm actually using my 1st generation IPad while I am at home so I can leave my new $900 iPad on a table to charge free of incident so I can use the 4G while I'm away from wifi during the day. I have been getting more upset about this because I can not even use the Griffin extended cord to charge the iPad and be far from the plug because only the original apple sync/charge cord will have a better shot at staying in. Absolutely none of my non apple cables will stay in the iPad 3 while having it in my hands.
    The plug is at an angle, unlike the first iPad, not sure about the iPad 2. Please let me know if they have same issue.
    If anyone else is having this problem with the Gen 3 iPad please let me know because I'm tempted to do something about it with apple and I'm hoping that I just for some reason have a bad cable receiver or something and maybe I can get a replacement and enjoy the iPad as I had expected to. There is no reason why I should be even using my first iPad and I have friends that want to buy it but I am not selling it because I'm unable to sell it because I can't handle the new iPad while it's plugged in, that is ridiculous if it's a common issue so please let me know!

    Thanks for the swift reply, I have been looking online and a loose plug seems to be somewhat of an issue with many, I hope mine is actually a problem and not what others are experiencing. It's taken me this long to even reach out for the simple fact I HATE being a complainer but this is just horrible.
    Do you have an iPad 3 as well? And is yours not experiencing any issues close to mine?
    Thanks again!

  • Having Problems With The Neo2 ? Read This!!!!

    Hi,
    i just bought a neo2 motherboard, with a p4 2,6 HT and 512 mb Kingston hyper ram ( 2 peaces of 256, else it won't use the dual bandwith :D)
    In the beginning everything seemed fine, until i got some sudden reboots and other vague stuff. I read it could be the SB audigy messing things up. I removed the card and windows Xp pro runs fine now. no more sudden reboots or explorer not resonding crashes.
    But, i still had problems with games crashing. I got reboots. After i set the "automatic reboot after crash" to false, i got blue screens or lock-ups in my games.
    I wondered what it could be. Then i started to put my videocard ( a radeon 9700 pro 128 mb) in agp 4x mode instead of agp 8x! Now my games run without crashes, but benchmarks are not that high. 4780 marks with 3dmark 2003.
    I think i will send msi and Ati a mail concerning this problem. I don't know if it is PSU related. Maybe the videocard demands a little more power in agp 8x mode.
    Well, having probs with you're NEO2 ??
    remove the sb Audigy and turn the agp back to 4 using smartgart ( it's located in you're display settings screen ).
    First i tought it was a PSU related problem, because i swapped my 350 Watt enermax with a Q-tec 400 watt psu. The 400 watt PSU died while i was gaming. Maybe the enermax is the better PSU :D So, it could still be a PSU related problem. Maybe the agp 8x settings demands a lot more from you're psu. Anyway, i'll receive a 550 watt Antec PSU soon, so i can check this out....
    Btw. I cant run the motherboard in anything better than "slow" mode. In all other modes Xp won't boot. I haven't tryed it since the AGP is at 4X, but i don't think it will matter.
    Regards,
    Welcome to the real world NEO :D

    Ok.....
    i raised the memory voltage setting in the bios from 2.65 to 2.8 and the agp voltage from 1.5 to 1.7
    Everything seems fine, but games crash back to the desktop now without an error message or the either lockup.
    Whatever i do, i can't make the mobo crash in anything but games!
    Btw. the following message caught my attention, when i ran f1 2002 with directx 8.1. Since i have directx 9, i haven't seen it anymore. Maybe because the ati-drivers are made for directx 9....
    // Watchdog Event Log File
    LogType: Watchdog
    Created: 2003-10-04 02:02:53
    TimeZone: -60 - West-Europa (standaardtijd)
    WindowsVersion: XP
    EventType: 0xEA - Thread Stuck in Device Driver
    // The driver for the display device got stuck in an infinite loop. This
    // usually indicates a problem with the device itself or with the device
    // driver programming the hardware incorrectly. Please check with your
    // display device vendor for any driver updates.
    ShutdownCount: 9
    Shutdown: 0
    EaRecovery: 1
    EventCount: 2
    BreakCount: 2
    BugcheckTriggered: 1
    DebuggerNotPresent: 1
    DriverName: ati2dvag
    EventFlag: 1
    DeviceClass: Display
    DeviceDescription: RADEON 9700 PRO
    HardwareID: PCI\VEN_1002&DEV_4E44&SUBSYS_00021002&REV_00
    Manufacturer: ATI Technologies Inc.
    DriverFixedFileInfo: FEEF04BD 00010000 0006000E 000A18EA 0006000E 000A18EA 0000003F 00000008 00040004 00000003 00000004 00000000 00000000
    DriverCompanyName: ATI Technologies Inc.
    DriverFileDescription: ATI Radeon WindowsNT Display Driver
    DriverFileVersion: 6.14.10.6378
    DriverInternalName: ati2dvag.dll
    DriverLegalCopyright: Copyright (C) 1998-2002 ATI Technologies Inc.
    DriverOriginalFilename: ati2dvag.dll
    DriverProductName: ATI Radeon Family
    DriverProductVersion: 5.2.3790.2
    I wish i had another videocard to test. My radeon 9700 pro is getting suspicious...
    Regards,
    The real world

  • Is anyone having problems with the battery heating up and draining the power?  Mine has been doing this for about 2 months now.

    Is anyone having problems with the battery heating up and draining the power?  Mine has been doing this for about 2 months now.

    This is a major problem with Lollipop, but yo said it started 2 months ago.   Several people have fixed problem by removing FaceBook And Face book messenger and then re loading the apps again.   You might want to clear your cache before reloading.  Not sure this is your problem, but worth a try.  Good Luck

  • I have upgraded Apple Aperture from version 2 to version 3 and I'm having a problem with the "Highlights and Shadows" adjustment. According to the user's manual, I should have access to an advanced disclosure triangle which would allow me to adjust mid co

    I have upgraded Apple Aperture from version 2 to version 3 and I'm having a problem with the "Highlights and Shadows" adjustment. According to the user's manual, I should have access to an advanced disclosure triangle which would allow me to adjust mid contrast, colour, radius, high tonal width and low tonal width.
    If anyone has any suggestions as to how to access this advanced section, I'd be most grateful.

    Hi David-
    The advanced adjustments in the Highlights & Shadows tool were combined into the "Mid Contrast" slider in Aperture 3.3 and later. If you have any images in your library that were processed in a version of Aperture before 3.3, there will be an Upgrade button in the Highlights & Shadows tool in the upper right, and the controls you asked about under the Advanced section. Clicking the Upgrade button will re-render the photo using the new version of Highlights & Shadows, and the Advanced section will be replaced with the new Mid Contrast slider. With the new version from 3.3 you probably don't need the Advanced slider, but if you want to use the older version you can download it from this page:
    http://www.apertureexpert.com/tips/2012/6/12/reclaim-the-legacy-highlights-shado ws-adjustment-in-aperture.html

  • HT4864 I am getting a triangle with an exclamation point next to my inbox...it says: There may be a problem with the mail server or network. Verify the settings for account "MobileMe" or try again.  The server returned the error: Mail was unable to log in

    I can send but cannot recieve email
    This is the messege I am gewtting:
    There may be a problem with the mail server or network. Verify the settings for account “MobileMe” or try again.
    The server returned the error: Mail was unable to log in to the IMAP server “p02-imap.mail.me.com” using “Password” authentication. Verify that your account settings are correct.
    The server returned the error: Service temporarily unavailable

    Also if I go to system preferences accounts and re-enter the password it fixes the glitch sometimes.

  • Problems with the O2 blackberry data package on my Curve 3G.

    I have already informed O2 about this but they claim that I should be used the blackberry support services, but nothing there helps me!
    I got my Blackberry Curve 3G on September 9th this year and I put on the Blackberry Data Package bolt-on onto my phone on September 16th. I then received a text to say they've taken £5 from my credit and it will be up and running in the next 24 hours. Its now September 19th and my BBM is not working at all and I am extremely upset with the services and behaviour I have received from both O2 and Blackberry.
    Is there any way you can help? If this fails, I shall be forced to go back to the shop from where I got my Blackberry from and ask for their help.
    Many thanks, Jade.

    Can a bubble whistle Problems with the O2 blackberry data package on my Curve 3G.? The seat matures in your oar. The lad ices the pursuing method inside a resident. A judge spins against the vendor! The rose wows the hello. 
    filipina heart

Maybe you are looking for

  • Control stmt CASE vs IF - Which is better

    Hi, I'm in the process of retrieving data from a table that has millions of rows. Now I need to count the numbers of rows where a particular field,TR_STATUS is either 'A','G' or 'K'. I have three different variables to hold the count on the rows with

  • Oracle 11g new insatllation - perl.exe issues

    Hi all, I have recently installed oracle 11g. It was running fine for a few days and then i get errors like 'TNS:listener does not currently know of service requested in connect descriptor'. I checked this out and the reason i get these errors is bec

  • How do you sort columns?

    i dont think i saw sorting columns in the doc. anyone can point me? thanks

  • Seem to have lost my required field option in Business Catalyst

    Hi there, I have set up a business catalyst form and formatted it but in the process have lost the required field functionality http://aom002.businesscatalyst.com/registration_copy.htm The form should not be able to be able to be submitted if the ter

  • Login window only shows "Other..." account listed

    For some reason when my wife reboot her iBook running 10.3.9 the login window came up and only showed the "Other..." account listed. Her account and mine are both not visible. Nothing was changed before rebooting and we cannot login using Other even