Problems with the setup of my new Z10

Hello.
Can anyone help me? I just got my new Z10 and I cannot get past the agreement menu, it keeps sending me back to the 'wi-fi connections' menu. I am connected to my mobile network, I have tried connecting to my home network, but the same thing happens (it forwards to the agreement menu, waits a while and then goes back to the wi-fi menu). I cannot turn off my wi-fi connections.
Please help.
Nici

Well, I'm glad to hear it has worked out now!
I only asked about the previous device as I wanted to make sure you were previously subscribed to BlackBerry data services.
Thanks!
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Similar Messages

Problems with the setup of my new AE

Hi to all. I have an Airport Express since a long time, that works properly. I got a new one, to extend my signal to other area of my house. The first time I connected the new AE (802.11n)to configure it, the Airport Utility recognized the devise but I got an error message that prompt me to repeat the previous steps. After this, the new devise can't be recognized to be configured. I have restarted the AE without luck. What I am doing wrong?

Hi - am having same problem. The Airport Utility sees the base station, but clicking Manual Setup or Continue sends it into a long search (for the config file I believe) and it then puts up error message "An error occured while reading the configuration file..."
All I can do is RESCAN.
Thought I had it sorted... Restarted both AX and iMac (G5) and got through the whole manual setup. Now it is saying "Your AX doesn't have a valid IP address... Make sure..."
I must say Apple isn't making it easy with this.

I have a problem with the WiFi on my new 4th gen 32g Itouch.

I have a problem with the WiFi on my new 4th gen 32g Itouch. It is showing the bars and the wifi connection is showing that it is on but I can't get onto any of my apps that use the internet. Any suggestions as to what might be the problem? Thanks!

- Do other devices successfully connct to the same network?
- Does the iPod successfully connect to other networks?
Try :
- Reset:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Powering off and then back on your router.
- Resetting network settings: Setings>General>Reset>Reset Network Settings
- The troubleshooting here:
iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections

Problem with the AF of my new 18-135mm EFS IS STM lens

Hello,
The lens came with the EOS Rebel T5i bundle.
The auto focus is working incorrectly, focusing closer than the detected area. This is happening when I use the viewfinder. When a picture is taken using the “direct view” (LCD display) it focus correctly.
I didn’t use the camera a lot since I bought it, now looking the first pictures I see that this problem is happening since I bought it.
I changed the zoom lens with another Canon camera and then my new Rebel T5i works fine and the same problem happens with the other camera, therefore I’m sure that the problem is in the lens and not in the camera body.
The out of focus is more noticeable when I'm taking pictures in 18mm position to an object farther than 2 meters but it is happening in any zoom position. It is clear when I compare the same picture taken with the viewfinder with one taken with the LCD Display.
I updated the body firmware and the problem continues.
Is it possible to update the lens firmaware? I couldn’t find them in the canon webpage.
I will go into an important trip next week, therefore I will not have time to send the camera to repair.
Any idea?
Thanks!

You may want to rent a lens for your trip and get this lens to service.
You'll want to be sure it really is a problem with the lens (it sounds like it is from your description). Test the lens against a "flat" target (such as a wall). You can hang something on the wall with high-contrast (newspaper works great) and put the camera on a tripod. The idea is that (a) the camera is definitely not moving, (b) the focus target is definitely not moving, and (c) the target is flat and there are no distracting objects in the field of view so it's not possible for the focus system to decide to lock focus on anything OTHER than your intended target.
Next... deliberately turn the focus ring to put the camera out of focus (so that the camera HAS to move the focus). This is mildly tricky with an STM lens since there's no mechanical link from the focus ring to the lens -- it's electronic. The lens only accepts focus input when focus is active (e.g. half-press the shutter button, etc. to wake it up.) I run focus all the way in and test several times, then run focus all the way out and test several times (that way it has to move focus in both directions.)
If the lens is consistently focusing closer, then it will need service.
Tim Campbell
5D II, 5D III, 60Da

Problems with the creation of a new domain using JCAPS6

Hello again,
I created a new domain, in addition to default domain1, with JCaps 6, following the steps in this link:
http://blogs.sun.com/polyblog/entry/creating_a_new_caps_6
I arrived to the step 4 of the procedure "install runtime installation" and I adapted install.xml file also (not only the install.properties), with the correct values concerning domainName and port.
When I run the ant-command then, I always get the following error:
C:\JavaCAPS6\appserver\bin>asant -f C:\JavaCAPS6\appserver\addons\caps\install.xml
Buildfile: C:\JavaCAPS6\appserver\addons\caps\install.xml
install:
install:
[sun-appserv-admin] Executing: list-lifecycle-modules port 19048 host localhost passwordfile "C:\JavaCAPS6\appserver\addons\caps\install.properties" user admin server
BUILD FAILED
C:\JavaCAPS6\appserver\addons\caps\install.xml:86: The following error occurred while executing this line:
C:\JavaCAPS6\appserver\addons\caps\applicationVerifier\server-init.xml:41: An exception occurred while running the command. The exception message is: CLI137 Command list-lifecycle-modules failed..
Total time: 1 seconds
How can i do to solve this problem?
Thanx
Edited by: fabrigas84 on Sep 3, 2009 8:36 AM

Hai!
Raise a message in sap support portal.
Regards,
Thanga Raj.K

Problems with the location on facebook blackberry z10

hi ,
my blackberry z10 facebook application doesn't show my location when i update a status or a check-in
i will be pleased if you could help me to solve this issue

This is a known problem with Internet Explorer 11, which Microsoft has been aware of since October 18 when they released their latest "untested" browser. The pages can't recognize the browser, so they don't recognize any of the plugins, like Flash Player. So far, Microsoft has made NO indication that they have any plan to fix it soon.
Microsoft's recommendation is to use Compatibility View for affected pages, and "pretend" you're using an different browser. Trouble with that is it has seen limited success at best, and you have to individually enable it for EVERY page that has problems.
I'm not big on "pretending" so I recommend actually using another browser.
Firefox (from Mozilla)
Opera (from Opera)
Safari (from Apple)
Chrome (from Google)
ANY of those will work where IE11 won't, with the Flash Player Plug-in (For all other browsers), and Chrome doesn't even need that because it has its own Flash Player plugin built in.

Problems with the Setup Wizard for WRT54GC

Hi…
I just bought a WRT54GC router and while trying to install it I had some problems.
I opened the Setup Wizard on the CD to install the router.
When I reach step 6 the internet connection is being checked with the following result: “Unable to detect the internet connection. Please check your cable connections”.
I’ve checked all the cables and everything is okay – I’m also able to access the internet which shows me that all cables are correctly connected.
So why do I get this message?
What do I have to do?
The problem is that I’m not able to continue the Setup Wizard further than step 6.
Thanks!

well..if you have an internet connection through the router and the CD setup shows “Unable to detect the internet connection. Please check your cable connections”. I would recommend you to neglect it....discard the CD and configure the router manually
you can access the router from the wired computer using http://192.168.1.1 .. the default password is admin

Problems with the setup of Adobe Digital Edition...Help!

I just purchased an ebook, and I had followed all the steps towards viewing it. When I went to the setup screen for the digital edition, I put in my newly setup ID and password, selected "authorize computer", and pressed the activate button. When I did this, this messege popped up "Error communicating with AdobeID server. Please try again later", followed by the code:
E_AUTH_ADOBEID_COMMUNICATIONS http://adeactivate.adobe.com/adept/SignInDirect
If someone could help me out with this, that would be greatly appreciated!
Thank you.

Crystal,
I've seen a couple of reports of this lately, all from the U.K. But that's the only pattern so far...
Please open a Digital Editions 1.5 Technical Support case, please use the contact links at http://www.adobe.com/support/digitaleditions.
Also reply back to this thread with your location please..
Regards,
Bentley Wolfe
Senior Support Engineer, Flash/Flash Player/Digital Editions
Adobe

Hi I just purchased a WVC54GCA wireless video camera I am having a problem with the setup software

I just purchased this wireless video camera and I am trying to set up the wireless key. I have put in the SSID and then the option of WEP (128 bit) or 26 character key. I then try to input the 26 character key and the text box can't take that number so I am supposed to click next and enter the key on the next page..... only it is at the last page where you would save the settings and I don't see anywhere to edit it. I know I get a bit hurried is there something I am missing?? I would appreciate any assistance you can offer. Thanks a ton

If you are trying to configure your Camera using the Setup disk, you can exit from the setup and configure all the settings on your Camera Manually.Follow the Instruction below to Configure your Camera manually..
1. Connect your Camera to a computer, click on the Start button >>> Settings >>> Control Panel >>> Network Connections - Right click on the icon for Local area connection and go to properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Select 'Use the following IP address'- Provide IP Address - 192.168.1.5, Subnet Mask - 255.255.255.0...Click on Ok button to Save and Click on "Close" on main Properties window...
2. Now open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.115.
Use admin for both Username & Password in lower case...It should open your Camera set-up...
3. Once you get to the set-up page you can follow this link to change the Camera Settings...While changing the Camera settings you have to make sure that the Wireless Settings(SSID/Network Name and WEP/WPA Key) are identical on both the devices(router and camera)...Also make sure to change the camera's default IP to match your network and Gateway Address should be your router's address...ex. Camera's IP Address : 192.168.1.115(assuming your router's default address is 192.168.1.1), Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1.
4. After configuring the Camera you should disconnect it from the Computer and go into Local Area Connection TCP/IP Properties and set it back to Obtain IP Address Automatically...Disconnect the Camera from the computer and power cycle both the devices(Camera and Router)...Your camera should be configured...
In case if you don't get the Camera set-up just leave it connected to your computer and reset it for 30 seconds...
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your Camera, wait for 30 seconds and re-connect the power cable...Follow Step 2, Step 3 & Step 4...
Click Here and follow the instructions to configure the camera with the Wireless Settings.

Problem with the creation of a new user

Hi!
II want to create new user in the database but i have this message: this entry already exists in the following tables (CUMI).
This user doesn't exists and we haven't deleted users.
When I am going to see in the table OUSR I have 19 users
But when I am going to see the table CUMI, it recognises an user code 20!
when I use the orange arrow near the user code 20, nothing happens.
SAP 2005 A PL 46
How can i do?
Thank you
Séverine

Hai!
Raise a message in sap support portal.
Regards,
Thanga Raj.K

I am having email problems with the new Lion. stmp, imap, etc. I have looked up google info and It is confusing when it comes to TS, SSL also, please explain how to set it up so my email goes out and comes in securely. Help

I am having email problems with the new Mountain Lion. stmp, imap, etc. I have looked up google info and It is confusing when it comes to TS, SSL also, please explain how to set it up so my email goes out and comes in securely. Help
Incoming Mail (IMAP) Server - requires SSL:
imap.gmail.com
Use SSL: Yes
Port: 993
Outgoing Mail (SMTP) Server - requires TLS:
smtp.gmail.com (use authentication)
Use Authentication: Yes
Use STARTTLS: Yes (some clients call this SSL)
Port: 465 or 587
Account Name:
your full email address (including @gmail.com) Google Apps users, please enter username@your_domain.com
Email Address:
your full Gmail email address ([email protected]) Google Apps users, please enter username@your_domain.com
Password:
your Gmail password
The Quick Answer
Follow the instructions below to set up IMAP1 access in most email clients.
Google Apps users, please follow the default instructions unless otherwise noted, replacing 'your_domain.com' with your actual domain2 name.
this is all greek to me. WHAT IS STARTTLS? On the first page of Apple set up there is a TLS certificate and it is marked NONE- should I change it to the long APPLE CERT option? The next page under ADVANCED: THERE IS A BOX SSL MARKED. Then IMAP Path Prefix - I put stmp.gmail.com.. is that right? Port 993 can use this one? as 456 doesn't work and 587 said it wasn't safe. Under AUTHENTICATION I used PASSWORD. Should I have used external client cert TLS?
Please help me set this up securely. Thanks

Apple - Support - Mail Setup Assistant

I keep geting this message when trying to udate to Itunes 10.5.1 "There is a problem with the Windows Installer package. A program run as part odf the setup did not finish as expected . Contact your support prersonel or package vender"

I keep getting this message when trying to upgrade to Itunes 10.5.1
Driving me nuts trying to upgrade. What can I do to correct this?
"There is a problem with the Windows Installer package.
A program run as part odf the setup did not finish as expected .
Contact your support prersonel or package vender"

Yes, I had found a similar solution also. I'm running XP Pro, SP3. I went Control Panels/ Add-Remove programmes/apple software update/ change/ repair. Then run the 10.5 exe.
While the programme updated from version 8 of iTunes, my new iTunes is now a mess. Not all of my music was in the same folder previously but it all showed up on iTunes. Now many albums have been left out, some have only a few tracks and some have two copies of some tracks as well as having other tracks missing. I haven't begun to work on that.

Is Anyone Having Problems with the newer version of Firefox?

I still have my older Mac OsXv10.4 Tiger software. I wasn't exactly happy with Safari browser as it would block many sites and were considered incompatible so I downloaded the free Firefox browser (the 2.0 version) of which I STILL have. I'm aware that there is a much newer version and would like to download that, but I've heard a lot of people saying they have been having severe problems with it, but then they have PCs and not Macs.
So my question is for you Mac users that use Firefox, have you had major problems with the newer version? I'm real hesitant to download if I'm going to have the same problem PC users are having...like constantly crashing. Also would my old Tiger software be compatible? I don't want to upgrade to Leopard.

Yes. I had problems with Firefox 3.5. The primary problem was very slow or never-ending loading of certain websites (particularly secure sites and sites with many features). I also have had similar, but not as bad, problems with Safari 4. I never had these problems with Safari 2 or Firefox 2. It just seems that with each update, the problems increased for me. I have read the Safari and Firefox forums and tried many fixes with little improvement. I have come to the conclusion that there is some kind of compatibility problem between the latest versions of Safari and Firefox and Shockwave Flash and/or Javascript and OS 10.4, particularly on PPC Macs. I expect there are many who will disagree and I cannot argue or prove the point. This is just my opinion. And I recognize that my problems could be caused by my setup and not by the browsers. By the way, I do not use any add-ons with any of my browsers. Anyway, I got tired of dealing with it and installed the latest version of Camino about 2 weeks ago. I also did a clean install of Firefox 3.0.13. Camino is working out great for me. It is simple and it works. No problems at all. So currently I am using Camino as my primary browser and Firefox 3.0.13 as my backup. I hope this helps.

Start-up problem with the Z10

Can you assist us in a Start-up problem with the Z10's.
I have read a lot of complains with the Z10 starting-up and then got stuck at 98% completion. No further response after that!
For any further information please check the "BlackBerry Support Forum" on this same site.
Please respond or tel me who i can contact in this regard?
Thank you
Kobus69
Subject Title and beginning of post edited to reflect new topic.

Hi
Please find the link given below might help you to fix your issue.
Resolve Boot Device not Found Error Message
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Is anyone having a problem with the new iPad (Gen. 3) not staying connected to the charger? It seems to ALWAYS get jiggled loose and no longer be charging. My iPad 1 has no issue but I can't browse Internet w/o new iPad unplugging. Horrible!

I notice that my new IPad (3rd generation) will not stay connected to the power cord at all, I'm not exagerating, if I plug it in and browse the Internet without fail it will become unplugged and I will have to push the plug back in (Ba-beep). Ive actually grown to despise that sound when you plug your iPhone or iPad in because it reminds me of how much money I spent on something that PHYSICALLY will not charge while I'm using it.
I know the problem with it holding a charge while in use, I get it, the screen is amazing and it takes a lot to run the display, however, it is unacceptable to me that I can't even keep the thing plugged in while I'm using it. I can not even leave it on my Cal King bed overnight because I will wake up in the morning to find that the plug has been jiggled loose in a corner, so it's still attached but not making a connection thus not being charged.
I love the 4GLTE from Verizon and I love the iPad, but I'm actually using my 1st generation IPad while I am at home so I can leave my new $900 iPad on a table to charge free of incident so I can use the 4G while I'm away from wifi during the day. I have been getting more upset about this because I can not even use the Griffin extended cord to charge the iPad and be far from the plug because only the original apple sync/charge cord will have a better shot at staying in. Absolutely none of my non apple cables will stay in the iPad 3 while having it in my hands.
The plug is at an angle, unlike the first iPad, not sure about the iPad 2. Please let me know if they have same issue.
If anyone else is having this problem with the Gen 3 iPad please let me know because I'm tempted to do something about it with apple and I'm hoping that I just for some reason have a bad cable receiver or something and maybe I can get a replacement and enjoy the iPad as I had expected to. There is no reason why I should be even using my first iPad and I have friends that want to buy it but I am not selling it because I'm unable to sell it because I can't handle the new iPad while it's plugged in, that is ridiculous if it's a common issue so please let me know!

Thanks for the swift reply, I have been looking online and a loose plug seems to be somewhat of an issue with many, I hope mine is actually a problem and not what others are experiencing. It's taken me this long to even reach out for the simple fact I HATE being a complainer but this is just horrible.
Do you have an iPad 3 as well? And is yours not experiencing any issues close to mine?
Thanks again!

Problems with the setup of my new Z10

Similar Messages

Maybe you are looking for