Problems with User Tracker getting info on Unrouted Network

I have two networks that I need UT info for, but both of the interfaces are not routed.  My thought was to configure an interface on each of these networks on a Cat 3750 and add a third interface into my management network to all Cisco Works to poll the switch for UT info.  I did this, but when I look at the ARP on the 3750 it isn't being populted.  I did a broadcast ping on both networks and I still don't see the ARP being populated.  Any ideas if this will work and if not suggestions on how to pull the UT info on these nonrouted networks?
Thanks,
Adam

The 3750 would probably need to act as the default gateway for hosts on these networks so that it learns the ARP entries.  What you can do is change the hosts to use the 3750, then have the 3750 redirect the hosts to the actual default gateway.  An alternative would be to use something like the Embedded Event Manager to periodically ping sweep the connected subnets to keep the ARP cache populated.

Similar Messages

  • Problem with user tracking in cisco prime Lms

    i attach my senario pic ,
    i use snmp v3 for my switch ,,
    discover -- ok
    synchronization  ---- ok
    net config and config edit ----- ok
    but my problem is
    report / inventory / user tracking / quick report ---------------------------------------- i take this notification for all report : no end hosts found
    i install UTU but this program can not found any record too .
    please help me

    NMS servers access the Bridge-MIB data from devices, to get the MAC/CAM table. Because MAC-address or CAM table is maintained on device/VLAN basis, so query needs to be made per VLAN based.
    In snmp v1/v2c SNMP Community String Indexing is used. Where vlan is polled by adding VLAN number after community string after @ sign. Example to see all the mac-address table from VLAN 1, if the community is test123, device would be polled like :
    snmpwalk -v2c -c test123@1  10.10.10.1
    The syntax is [community string]@[instance number].
    For snmp v3 this is not an option, as it cant use SNMP community string indexing. So all the MAC/CAM table needs to made snmp v3 context aware, which exposes BRIDGE-MIB data to SNMP v3.
    You must use contexts to get per-VLAN data from the BRIDGE-MIB with SNMPv3.Not all the IOS switches support this. In general, if the device supports the "show snmp context" command, contexts will work. If not, an upgrade is needed. However, some switches (e.g. 2950 series) will never support SNMPv3 contexts. You must use v1/v2c with these switches.
    Very simply, you need to add the context to the SNMP group to allow your users to poll the given context. For example, to allow users to poll the BRIDGE-MIB for context vlan-6, you would add something like:
    snmp-server group v3group v3 auth context vlan-6 read
    You should add all those exact name after context which you see in output of show snmp context.
    Also, about UTU, it is just a small utility tool to access the LMS User Tracking DB externally to show the UT data, so unless LMS has UT data in its DB, UTU won't a difference either.
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • Problem with user tracking Cisco Prime lms 4.2

    Hi
    When I use the User tracking utility, it dont find the usernames, I dont kwow if I have to use the tool UTlite33.exe un all end host or not, please helpme.

    Hi Andres,
    Check this ::
    Understanding UTLite
    UTLite is a utility that allows you to collect user names from Primary Domain Controllers, Active Directory, and Novell servers.
    To do this you need to install UTLite in the Windows Primary Domain  Controllers and in the Novell servers. You can also install UTLite in an  Active Directory server.
    UTLite sends traps to LMS whenever a user logs in or logs out. UTLite  traps are processed by LMS at the rate of 150 traps per second, with a  default buffer size of 76800.
    Follow the below link and it should help:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.0/user/guide/admin/appendixcli.html#wp1032284
    Thanks-
    Afroz
    [Do rate the useful posts]

  • After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

    After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

    1. Download the iOS 5.0.1: http://www.tobias-hartmann.net/2011/11/download-ios-5-0-1-veroffentlicht-direkte -downloadlinks/
    2. open itunes,Click in iTunes while holding down the Shift key (on Windows) or Alt key (Mac) to restore and firmware

  • Has anyone had a problem with Draft Emails getting sent with Mac OS 10.8.2? It just happened to me and sent a few drafts out to a potential employer I planned on sending out torrow.

    Has anyone had a problem with Draft Emails getting sent with Mac OS 10.8.2? It just happened to me and sent a few drafts out to a potential employer I planned on sending out tomorrow.

    Hi, one question & one suggestion...
    What possible things are connected at home but not at the store, inlude every cable, etc.
    One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
    PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
    Reboot, test again.
    If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or some USB or Firewire device, or 3rd party add-on, Check System Preferences>Accounts>Login Items window to see if it or something relevant is listed.
    Check the System Preferences>Other Row, for 3rd party Pref Panes.
    Also look in these if they exist, some are invisible...
    /private/var/run/StartupItems
    /Library/StartupItems
    /System/Library/StartupItems
    /System/Library/LaunchDaemons
    /Library/LaunchDaemons

  • Problem with user-defined functions in XQuery String

    hello
    i've a problem with user-defined functions in XQuery String
    details are here (the code is not Human-readable via forum's embedded editor ?? strange)
    http://docs.google.com/Doc?id=ddqwddsr_21c96d9x
    thanks !!

    See
    michaels>  select xmlquery('declare function local:test_function($namecmp as xs:string?, $inputtype as xs:string?) as xs:string?      
                        return {$inputtype}
                     local:test_function("1","2")' returning content) o from dual
    Error at line 5
    ORA-19114: error during parsing the XQuery expression:
    LPX-00801: XQuery syntax error at '{'
    3                       return {$inputtype}
    -                              ^
    michaels>  select xmlquery('declare function local:test_function($namecmp as xs:string?, $inputtype as xs:string?) as xs:string?      
                        $inputtype
                     local:test_function("1","2")' returning content) o from dual
    O   
    2   
    1 row selected.

  • Problem with users disabling ARD client service

    I've got a problem and i'm not quite sure of the work around. I'm a PC guy by nature and can't quite figure this out.
    I'm having a problem with users disabling the ARD service from the sharing menu. Unfortunately users need to have admin privleges to do their work so I can't simply give them a standard account.
    I've hidden the ARD user account i created from the login window through Netinfo, but I need to find a way to stop users from shutting the ard service down.
    They don't seem to understand that the company requires that it be on the computer. Now, I'm the one who is set as the admin for ARD in the building, however we really just use it to rollout drivers, install packages, and its a lifesaver for remotely fixing problems with programs. The company didn't really buy it to spy on the employee's.
    Is there any way to hide the service from an admin level account? Or keep them from shutting it down?
    BTW, this would have to be done on multiple machines running both panther and tiger.
    Any help would be appreciated as I'm not quite sure where to start.

    First, as a matter of policy, let them know this service is active, and needs to remain active. If they disobey this instruction and turn it off, you have a human resources issue, not a technical issue.
    Second, there are very few enterprise users that need admin access to their machines. Oh, they ALL think they do, and there will be howling when non-admin status is first imposed, but we have 350 users in a publishing environment with less that 20 setup as admins. Those users are almost all superusers who assist others in a technical role.
    We have far fewer software problems like this and with ARD, IT can install/ authorize installation of software remotely should a user need that. It simply does not dramatically impact our users to have non-admin access. On the other hand, we recognize that a FEW users will need more access, and grant that on a case-by-case basis.

  • Problem with user mapping

    Hello,
    We got a problem with user-mapping to a SAP system.
    We create a SAp system, and an alias to this system.
    We add a user mapping for the administrator (user, not group). Check for connector is OK.
    Now, we make the same user-mapping for a group.
    if the user also belongs to the group "administrator" this mapping works, otherwise this fail with a message <b>"com.sapportals.portal.ivs.cg.SystemNotFoundException: Got null system object for alias R3HR".
    </b>After checking, there is no user-mapping for the "administrator" group, nor for the roles that belong to that group, nor for the user.
    So, it seem that the alias is only visible for an admin.
    does any one got an idea ? we are on SP14, Linux.
    regards
    Guillaume PATRY

    HI Guillaume,
    The user mapping is available for both Admin as well as end users.
    Open your system from System Administration>System Configuration>System Landscape.
    In the property editor,in dropdown for property category,
    select the logon method as UID?password and User Mapping type to admin/user.
    Then you can create a Group,map the system alias for this group and add users to this group.
    Also,in the property editor for the system,from dropdown for display,select permissions , and add the group to asssigned permissions as READ ONLY and select the checkbox for ENDUSER.
    Hope,this resolves your problem.
    Regards,
    Siddhartha

  • Does anyone have problems with iPhone 5 getting hot?

    Does anyone have problems with iPhone 5 getting hot? I just bought a new iPhone 5 &amp; it's gotten hot twice. Once when I was on FaceTime for 30 min it got hot about 15 min into the call. &amp; once when I was downloading some apps.

    http://support.apple.com/kb/HT2101?viewlocale=en_US
    It is normal for it to get warm when it's being used, especially if it is hot outside. It can even get uncomfortably warm. As long as it is not causing you physical harm (as in giving you burns) or displaying a temperature warning, then it's normal behavior. It's like taking your laptop outside and using it. Except the laptop will probably burn you.

  • Problem with user number

    Goodmorning, I have a problem with user number of my smartphone Blackberry Curve 8900: when I call a numer of my adress book, on the right,  appears a user number, that I don't know. Why dont'appears mine? I don't have buy this smartphone personally, but I had it (used) through the smartphone's owner...I think that the user number that appears on my display is his. How I can do to remove it?
    Waiting for an answer, thank you.

    Hello scricciolina90
    Welcome To Support Forums
    On or Curve 8900 from the Home screen > click Options > Click Advanced Settings > SIM Card > Highlight the phone number > Press the Menu key and click Edit SIM Phone Number > Check that field or Enter you Mobile number in that field .
    Good luck.
    Click " Like " if you want to Thank someone.
    If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

  • TS3694 good evening i have an problem with my iphone 4 the wif and network cant on now if i tray is showing iTunes i tray to reload the ios is showing an error -1 can you help me

    good evening i have an problem with my iphone 4 the wif and network cant on now if i tray is showing iTunes i tray to reload the ios is showing an error -1 can you help me

    No problem, glad to help!
    Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

  • Problems with audio tracks

    Happily pressing on with my first project when problems arose with audio tracks. Suddenly - when I added video clips I got sound on A2 but nothing showing on A1 (and sound only from right hand speaker). Clips are okay as sound is on both sides when played in Viewer and Canvas just can't add them both to timeline. It was okay up until the point I did my first audio fades within a clip (using the 'elastic bands'). Now I can't even insert a clip with both tracks ahead of that point. A1 just won't accept anything.
    Now when I add a clip I only get audio on A3!!!!
    Voiceovers all went onto A6 and are okay but is it normal for them to hide down there?
    I am sure this is finger trouble on my part as I am so new to FCE but can anyone tell me how to recover?
    Thanks,
    Tom.

    Sounds to me like the audio targeting is amiss somewhere.
    In the audio tracks you will notice a1 & A1: meaning audio track 1 and the audio will go to that track when edited. To get stereo, two tracks will be used eg. a2 & A2. Having A1 and A2 is FCEs default setting with a1 & a2 selected. This setting will place stereo audio into these default tracks. If, for example, you want the tracks to be edited to A5 & A6 then you move the a1 to a5 and a2 to A6 (click and drag). This is called track targeting for obvious reasons, untill you change it, all new edited tracks go to tracks 5 & 6.
    Click on a1 twice, did you notice it move and seperate from A1, this is a de-selected state (a gap between a1 & A1). When a clip is edited to A1 in this state it means no audio will be added to that track. Most likely you have an unlinked audio track. I hope this brief bit of info helps you figure out what audio ends up where in the Timeline.
    Regarding recovery, you could try the AutoSave Vault. Go back to a date and time that is before things went wrong and open that project.
    Al

  • Problems with User profile Application not available

    Hi
    Have a 2 tier SP 2010, with SQL server and a single SharePoint2010 server. We have a problem with the User profile Application service.
    The main problem is that we cannot go to "Edit" under Manage User Profiles. If we want to edit a user, we just get an error:
    "Microsoft.Office.Server.UserProfiles.UserProfileApplicationNotAvailableException: No User Profile Application available to service the request. Contact your farm administrator."
    When rebooting the server, we get the following in event viewer: Warning: ASP.NET 2.0.50727.0
    Event code: 3005 
    Event message: An unhandled exception has occurred. 
    Event time: 2/5/2015 12:25:25 PM 
    Event time (UTC): 2/5/2015 11:25:25 AM 
    Event ID: 84d104331476453b88c60a37d7a0b8fe 
    Event sequence: 9 
    Event occurrence: 1 
    Event detail code: 0 
    Application information: 
        Application domain: /LM/W3SVC/1212406818/ROOT-1-130676090755160256 
        Trust level: WSS_Minimal 
        Application Virtual Path: / 
        Application Path: C:\inetpub\wwwroot\wss\VirtualDirectories\14877\ 
        Machine name: SPMACHINE 
    Process information: 
        Process ID: 4668 
        Process name: w3wp.exe 
        Account name: domain\spfarm 
    Exception information: 
        Exception type: UserProfileApplicationNotAvailableException 
        Exception message: No User Profile Application available to service the request. Contact your farm administrator. 
    Request information: 
        Request URL: http://sp2010:2010/_layouts/ProfMngr.aspx?ID=51982fe8-4886-4ebd-ad68-f5934656e54d&IsDlg=1 
        Request path: /_layouts/ProfMngr.aspx 
        User host address: ::1 
        User: domain\spfarm 
        Is authenticated: True 
        Authentication Type: NTLM 
        Thread account name: domain\spfarm
    Thread information: 
        Thread ID: 15 
        Thread account name: domain\spfarm 
        Is impersonating: False 
        Stack trace:    at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.ProfileAdminPage.get_CurrentApplication()
       at Microsoft.SharePoint.Portal.UserProfiles.AdminUI.ProfileAdminPage.get_CurrentApplicationProxy()
       at Microsoft.SharePoint.Portal.WebControls.ProfileQueryUsers._FillSubtypeCollection()
       at Microsoft.SharePoint.Portal.WebControls.ProfileQueryUsers..ctor()
       at ASP._layouts_profmngr_aspx.__BuildControlProfileQuery()
       at ASP._layouts_profmngr_aspx.__BuildControl__control6(Control __ctrl)
       at ASP._admin_admin_master.__BuildControlPlaceHolderMain()
       at ASP._admin_admin_master.__BuildControl__control21()
       at ASP._admin_admin_master.__BuildControl__control2()
       at ASP._admin_admin_master.__BuildControlTree(_admin_admin_master __ctrl)
       at System.Web.UI.MasterPage.CreateMaster(TemplateControl owner, HttpContext context, VirtualPath masterPageFile, IDictionary contentTemplateCollection)
       at System.Web.UI.Page.get_Master()
       at System.Web.UI.Page.ApplyMasterPage()
       at System.Web.UI.Page.PerformPreInit()
       at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)

    Hi Thomas,
    Based on the error message, I recommend to verify the things below:
    Please make sure that User Profile Service is started in Central Administration.
    Please make sure Forefront Identity Manager Service and Forefront Identity Manager Synchronization Service are started in services.msc.
    Change the schedule for the "Timer Service Recycle" job to run during off peak hours, when a small amount of timer jobs are running.
    Check ULS log for more detailed error message.  For SharePoint 2010, by default, ULS log is at C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\LOGS.
    Thanks,
    Victoria
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Victoria Xia
    TechNet Community Support

  • Field Guide 8 - Configuring the Database but problems with user id

    Iam just running into problem after problem with Chapter 8 dataproviders when I'am about 2/3 of the way through.
    I'am now trying to configure the "Login Data Structure" Page 363. After adding the derbyclient.jar file. Then opening DerbyLogin.java and thereafter clicking "Run" as instructed in the book I get this error.
    Error on url jdbc:derby://localhost:21527/sample
    ERROR: SQLException: Connection authorization failure occurred. Reason: userid invalid.
    org.apache.derby.client.am.SqlException: Connection authorization failure occurred. Reason: userid invalid.
    at org.apache.derby.client.net.NetConnection.mapSecchkcd(Unknown Source)
    at org.apache.derby.client.net.NetConnection.securityCheckComplete(Unknown Source)
    at org.apache.derby.client.net.NetConnectionReply.parseSECCHKRM(Unknown Source)
    at org.apache.derby.client.net.NetConnectionReply.parseSECCHKreply(Unknown Source)
    at org.apache.derby.client.net.NetConnectionReply.readSecurityCheck(Unknown Source)
    at org.apache.derby.client.net.NetConnection.readSecurityCheckAndAccessRdb(Unknown Source)
    at org.apache.derby.client.net.NetConnection.flowSecurityCheckAndAccessRdb(Unknown Source)
    at org.apache.derby.client.net.NetConnection.flowUSRIDONLconnect(Unknown Source)
    at org.apache.derby.client.net.NetConnection.flowConnect(Unknown Source)
    at org.apache.derby.client.net.NetConnection.<init>(Unknown Source)
    at org.apache.derby.jdbc.ClientDriver.connect(Unknown Source)
    at java.sql.DriverManager.getConnection(DriverManager.java:525)
    at java.sql.DriverManager.getConnection(DriverManager.java:193)
    at asg.databuild.DerbyLoginDB.createLoginDatabase(DerbyLoginDB.java:52)
    at asg.databuild.DerbyLoginDB.<init>(DerbyLoginDB.java:38)
    at asg.databuild.DerbyLoginDB.main(DerbyLoginDB.java:25)
    BUILD SUCCESSFUL (total time: 5 seconds)
    It's telling me that user ID is invalid. I have no idea what my db user id is or how I can check it with the bundled database as there is no documentation I have found about that. Nor do I even know what I have to do to properly configure this app to properly work with the bundled database as the field guide says absolutely nothing about this!Message was edited by:
    tutorials

    Found a solution to this problem for anyone else having the same problem please go to thread: http://forum.sun.com/jive/thread.jspa?forumID=123&threadID=99634

  • EP + BW: Problems with user mapping in the portal

    Hi,
    I'm trying to connect the portal with the BW by using the report RSPOR_SETUP which is a step-by-step guide. The steps #1 - #11 seems to be ok but my problem is the 12th step, the user mapping/allocation maintenance in the portal.
    There is an error emerging (in BW): System failure during call of function module RSWR_RFC_SERVICE_TEST (System failure indicates normally an authentication problem between ABAP and Java)
    Another error is emerging by testing the connection in the portal. (System administration u2013 system configuration u2013 system landscape u2013 connection test: the first connection, the SAP Web-AS connection is ok but the second, connection test for connector, is not working.
    Especially the connection to the backend system with the defined connector is not working. The output is: u201CConnection failure. Check that single sign on is correct configured.
    On step 12 of the step-by-step guide I have to select a user in the portal, relate him to a system alias und maintain his technical username and password for the BW. I think here is the problem. Iu2019m able to select and save a system alias for the user, but Iu2019m not able to save his technical username and password. There is another error emerging (in the portal): u201CVerification of user mapping data for system SAP_BW failed, check credentials for errorsu201D, so Iu2019m not able to save the username and password.
    I think thats the my problem. the log file confirms that: "Did not find any existing logon data for principal...." & "No user mapping data available for principal...."
    I hope my problem description is understandable.
    Any ideas how I can solve the credentials problem to save the username and the password?
    Thanks in advance.
    Tan
    Edited by: Tan Yildiz on Jul 22, 2009 1:26 PM

    I could deploy some of the usage types, but there is an error regarding the BI-REPPLAN package. I think it's one of the very last errors that stands between me and a working EP - BI connection. There is a problem with the version. Could you check the log details, to find out more?
    Thank you.
    <!LOGHEADER[START]/>
    <!HELP[Manual modification of the header may cause parsing problem!]/>
    <!LOGGINGVERSION[1.5.3.7185 - 630]/>
    <!NAME[D:\usr\sap\BIP\JC02\SDM\program\log\sdmcl20090806164716.log]/>
    <!PATTERN[sdmcl20090806164716.log]/>
    <!FORMATTER[com.sap.tc.logging.TraceFormatter(%24d %s: %m)]/>
    <!ENCODING[UTF8]/>
    <!LOGHEADER[END]/>
    Aug 6, 2009 6:47:16 PM   Info: -
    Starting validation -
    Aug 6, 2009 6:47:16 PM   Info: Prerequisite error handling strategy: OnPrerequisiteErrorSkipDepending
    Aug 6, 2009 6:47:16 PM   Info: Update strategy: UpdateLowerOrChangedVersions
    Aug 6, 2009 6:47:16 PM   Info: Starting deployment prerequisites:
    Aug 6, 2009 6:47:18 PM   Info: Loading selected archives...
    Aug 6, 2009 6:47:18 PM   Info: Loading archive 'D:\usr\sap\BIP\JC02\SDM\program\temp\BIREPPLAN04_0-10005889.SCA'
    Aug 6, 2009 6:47:21 PM   Info: Selected archives successfully loaded.
    Aug 6, 2009 6:47:21 PM   Error: Unresolved dependencies found for the following SDAs:
    1.: development component 'bi/plan/helpers/table2'/'sap.com'/'MAIN_NW701P03_C'/'2846642'/'0'
    dependency:
           name:     'bi/alv/common'
         vendor:     'sap.com'
    There is no component either in SDM repository or in Deployment batch that resolves the dependency.
    dependency:
           name:     'bi/alv/ui'
         vendor:     'sap.com'
    There is no component either in SDM repository or in Deployment batch that resolves the dependency.
    Deployment will be aborted.
    Aug 6, 2009 6:47:21 PM   Error: No Software Component Archive (SCA) or Software Delivery Archive (SDA) selected. Select at least one.
    Deployment will be aborted.
    Aug 6, 2009 6:47:21 PM   Error: Prerequisites were aborted.
    Aug 6, 2009 6:47:22 PM   Error: Error while creating deployment actions. No Software Component Archive (SCA) or Software Delivery Archive (SDA) selected. Select at least one.
    Deployment will be aborted.
    Aug 6, 2009 6:47:23 PM   Info: -
    Ending validation -

Maybe you are looking for