Problems with WEP Security?

If you are having difficulty making a wireless connection to your home network, check whether you are using the WEP security method with Shared Key authentication. These HP wireless printers do not support this security method, which is the least secure of the methods available. If you are unable to connect for this reason, the printer will indicate that the problem may be caused by MAC address filtering, which is misleading. To correct this problem, configure your wireless router to use one of the following supported security methods, all of which are superior to WEP/Shared:
·  WEP key encryption using either Auto or Open authentication
·  WPA
·  WPA2
Changing your router configuration from WEP/Shared to either WEP/Auto or WEP/Open while using the same WEP key, will allow most other wireless devices on your network to connect without your having to change their configurations. However, you might take this opportunity to update your security to WPA or WPA2 which are both far more secure than WEP. If you change your security type from WEP to WPA or WPA2, you will need to reconfigure all other wireless devices that connect to your network with the new settings.
After changing your router's security method, before attempting to connect your HP printer wirelessly, we recommend that you either restore network defaults from the printer’s control panel or turn the printer power off and then on again.
For help with your specific printer visit HP Customer Care: www.hp.com/go/customercare
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

change the router to use WPA. worked for me

Similar Messages

10.4.7 wireless connect problem with wep security

I can no longer connect either my powerbook or powermac to either of my wireless access points if wep security is used. One router runs wpa, the other has to run wep because that's all the print server can do. To pin this down, I found that both computers can connect to an access point configured wpa. And both can connect if security disabled. But neither can connect with access point setup with wep. System preferences says connected to the internet, but it's not. Before 10.4.7 I could connect with no problems. Have two PCs running XP that continue to access wireless router using wep security. Anybody having this problem? And any suggestions??
Thanks

Assuming you have 3rd party wireless routers, have you checked the router manufacturer's website to see if a firmware update is available for the router models targeted at OS X users?
I'm using WPA2 personal with my AEBS at Home and my girlfriend uses WEP with her AEBS at her house and I've had no problems connecting to her wireless network and accessing the internet with 10.4.7.
She also uses WEP with a 3rd party wireless router at her condo on the coast and I've had no problems connecting there either.

There is a problem with the security certificate of the proxy server. Error code 18 and 38.

Hi All,
After several hours and a short night of sleep I'm out of ideas and hopefully someone here can help me trying to solve this one. First of all the situation:
Exchange 2013 on a remote location with a CA-certificate.
Outlook 2010 and 2013 on different locations, locally installed and on RDS.
When I open Outlook on my laptop all is fine, no errors, good sync, no problem. But when I open Outlook on our Remote Desktop Servers with Outlook 2013 I'm getting errors like "There is a problem with the security certificate of the proxy server. The
name on the security certificate is invalid or does not match the name of the site. Outlook is unable to connect to this server. (Error code 18)". Opening Outlook 2010 the message is the same, but the error code now is 38.
After this Outlook opens and is working, there's one more error though. After a while an security warning pops up with the message: "Information you exchange with this site cannot be viewed or changed by others. However, there is a problem with the
site's security certificate. * The security certificate was issued by a company you have not chosen to trust. View the certificate to determine whether you want to trust the certifying authority. * The security certificate is valid. * The name on the security
certificate is invalid or does not match the name of the site."
Strangest thing is, it is the certificate of my RDS! It isn't my valid en officially bought certificate from my mailserver. What's going on? I'm out of options, what I've tried so far (in random order):
- restarting mailserver and AD;
- restarting switches;
- restarting routers;
- restarting RDS, AD and all other servers;
- bypassed proxyserver for RDS;
- created a new profile;
- checked recently installed updates;
- checked certificate on mailserver;
- checked RDS on a different location, working fine.
Nothing helped, what can I do next? Please advice.
Regards.

Found a thread that solves half my problem (https://social.technet.microsoft.com/Forums/office/en-US/70d18244-889a-4d95-ac3f-e234672a82b2/there-is-a-problem-with-the-proxy-servers-security-certificate-error-when-starting-outlook?forum=exchangesvrclients).
The first message can be suppressed by adding this to the Exchange config:
set-outlookprovider -Identity EXCH -CertprincipalName msstd:webmail.domain.tld
set-outlookprovider -Identity EXPR -CertprincipalName msstd:webmail.domain.tld
Giving the command get-outlookprovider, gives me empty information regarding the certprinipalname. Filled
this and after recreating the profile or deleting the ost-file I still have the second alert with the local certificate of my RDS.
Not completely where I want to be, any help regarding the second alert is greatly appreciated!

There is a problem with this connection's security certificate The remote computer cannot be authenticated due to problems with its security certificate. Security certificate problems might indicate an attempt to fool you or intercept any data you send

Hi,
I have this Windows 2008 R2 on which I installed remoteapp some years ago.
Now the certificate expired and I get the message
"There is a problem with this connection's security certificate
The remote computer cannot be authenticated due to problems with its security certificate.
Security certificate problems might indicate an attempt to fool you or intercept any data you send to the remote computer."
How should I renew the certificate? I already went to certification store and tried to renew certificate with same key but then it says "the request contains nor certificate template information".
Please advise.
J.
J.
Jan Hoedt

Does the computer account have Enroll permission to the certificate template?
From the Server running your CA, run mmc, click File then Add/Remove Snap-in...
Add Certificate Templates and click OK.
Find the certificate template, then right click and select properties. On my CA its call ed RemoteDesktopComputers but might be called something different depending on what what template your certificate is based on.
On the security tab, click Oblect types, check Computers then OK. Enter the Computername and click OK. Then give your computer account Enroll permisssion.
HTH,
JB

Hi all, I'm still having problems with my security questions as they were not the ones I answered. Now I'm confused

Still having problems with my security questions as they were not the ones I answered and now I'm confused.

Howdy Paul,
If you are having an issue with your Apple ID security questions, you can reset them using the steps in this article -
If you forgot the answers to your Apple ID security questions - Apple Support
Thanks for using Apple Support Communities.
Best,
Brett L

Hi i have a problem with my security question verify email address

hi,
i have a problem with my security question verify email address

If Manage your Apple ID primary, rescue, alternate, and notification email addresses does not help, you can contact the Apple ID Security site from http://support.apple.com/kb/HT5699 or call the AppleCare support number from http://support.apple.com/kb/HE57 and ask to speak with the Account Security Team.

I have problem with the security question i forgot it some body tell me they will show down of the question forgot the answering but nothing show help me plz thanks

I have problem with the security question i forgot it some body tell me they will show down of the question forgot the answering but nothing show help me plz thanks

The reset link will only show if you have a rescue email address (which is not the same thing as an alternate email address) set up on your account : http://support.apple.com/kb/HT5312
If you don't have a rescue email address (you won't be able to add one until you can answer 2 of your questions) then you will need to contact iTunes Support / Apple to get the questions reset.
Contacting Apple about account security : http://support.apple.com/kb/HT5699
When they've been reset (and if you don't already have a rescue email address) you can then use the steps half-way down this page to add a rescue email address for potential future use : http://support.apple.com/kb/HT5312

I have problem with the security question which i forgot the answer how can i change it as i already have apple id and password

I have problem with the security question which i forgot the answer how can i change it as i already have apple id and password

You may reset the password on your account by opening https://iforgot.apple.com/ in Safari and entering your Apple ID (your email address, which the moderators should have removed earlier).
You won't be able to set the password to your email address, or a recently-used password (if I remember correctly).
Once you change your password, you should update your password on your iOS device in Settings > iTunes & App Store, then tapping the "Apple ID: <username>" cell at the top to re-enter your password. (Your iOS device may prompt you for the new password before getting to Settings as well.)
Hope that helps. If you have a different issue, please post a follow-up message.

I have problem with the security questions and i dont know the answer. How i change the questions ?

I have problem with the security questions and i dont know the answer. How i change the questions ?

See Here... ask to speak with the Account Security Team...
Apple ID: Contacting Apple for help with Apple ID account security
Or Here > Apple Support iTunes Store Contact

I am having problems with my security questions. I cannot Get them reset. What do I do?

I am having problems with my security questions.
I cannot get them reset. How can I fix this?

Hi Tiffanyweir,
You need to contact iTunes Support to get them reset:
ACCOUNT SECURITY CONTACT NUMBERS
Cheers,
GB

Problem connecting to internet with WEP security on

Just got new iBOOK today. Wireless network in house, with two PCs and Powerbook set up - all working okay.
New iBOOK works using airport when WEP security disabled.
Have added the iBOOK's MAC address to the network and enabled WEP 64 bit security.
Try to connect, type in password, but error message appears.
Believe it may be a security problem on the iBOOK somewhere - but where?

Just got new iBOOK today. Wireless network in house,
with two PCs and Powerbook set up - all working
okay.
New iBOOK works using airport when WEP security
disabled.
Have added the iBOOK's MAC address to the network and
enabled WEP 64 bit security.
Try to connect, type in password, but error message
appears.
Believe it may be a security problem on the iBOOK
somewhere - but where?
Should have said it is a netgear DG834G
ibook G4 Mac OS X (10.4.3) Netgear Router DG834G

Netcfg problem with wep shared key

hello guys,
I would like to connect to a wireless device with netcfg. The device has a WEP encryption with shared key authentication. I'm able to connect using the gnome nm-applet, but with netcfg i keep getting the "Wireless association failed" error.
My config file for netcfg:
CONNECTION="wireless"
DESCRIPTION="A simple WEP encrypted wireless connection"
INTERFACE="wlan0"
SECURITY="wep"
ESSID="[essid]"
KEY="s:[password]"
IP="dhcp"
May the problem lie in the shared key authentication? I tried
IWCONFIG="enc restricted"
but it still doesn't work. I have an intel 3945 wireless card.
Any help is appreciated,
thanks.

what puzzles me is that
1) i'm able to connect to the same device if I set the open authentication,
2) I'm able to connect if I set the WPA protection, and
3) I'm even able to connect (with WEP and shared key authentication) using gnome nm-applet.
The only problem I have is with netcfg and iwconfig, so i'm asking if iwconfig has a specific problem with shared authentication and if there is a way to handle it.

Problem with socket security

Hi,
I'm trying to make socket connection from within air application, but no way. I'm browsing google for almost 2 days, follow all possible solutions, but avidently I dont understund somthing cause I'm not able to do anything.
Every time sandbox security violation..... I need make some simple socket data exchange between my air, and OS. I do not have any web server and no any other kind of network ability. I write down stupid socket server, which is waiting for policy request, and for my other requests (it function 100%, tested with Telnet, so no way to have problem on my socket server side).
The strange thing is that my application do not produce any request for socket policy file, neither at 843 port (for default), neither at my custom location with namual
Security.loadPolicyFile("xmlsocket://ip:port"); call
This is my primitive code:
<?xml version="1.0" encoding="utf-8"?>
<mx:WindowedApplication xmlns:mx="http://www.adobe.com/2006/mxml"
    layout="vertical">
    <mx:Script>
        <![CDATA[
            private var s:XMLSocket = null;
            private function test():void{
                Security.loadPolicyFile("xmlsocket://127.0.0.1:25013");
                if(!s){
                    s = new XMLSocket();
                    s.addEventListener(DataEvent.DATA, onData);
                    s.addEventListener(Event.ACTIVATE, onActivate);
                    s.addEventListener(Event.CONNECT, onConnect);
                    s.addEventListener(Event.DEACTIVATE, onDeactivate);
                    s.addEventListener(IOErrorEvent.IO_ERROR, onError);
                    s.addEventListener(SecurityErrorEvent.SECURITY_ERROR, onSecurity);
                s.connect("127.0.0.1", 25013);
            private function onActivate(e:Event):void{
                debug.text += "Activated\r";
            private function onConnect(e:Event):void{
                debug.text += "Connected\r";
                var o:XML = <request cmd="10"/>;
                s.send(o);
            private function onDeactivate(e:Event):void{
                debug.text += "Deactivated\r";
            private function onError(e:IOErrorEvent):void{
                debug.text += e.text + "\r";
            private function onSecurity(e:SecurityErrorEvent):void{
                debug.text += e.text + "\r";
            private function onData(e:DataEvent):void{
                debug.text += e.data;
                s.close();
        ]]>
    </mx:Script>
    <mx:Button label="Test" click="test()"/>
    <mx:TextArea id="debug" width="100%" height="100%"/>
</mx:WindowedApplication>
Any help will be apresciated.
Ladislav.

Hi,
It pass some time but if i remember well, my problem was that i did
not terminate stream output form my server vs air application, and it
returns this security error.
When I send '\0' at the end of my message it work correctly. Yes the
server was my own written socket server (c++ using boost libraries).
Laco.
Sorry late response I'm on hollydays
Staney G ha scritto:
So, how did you walk around the problem? Did you have a control on how server responds?
My test case failed similarly. However, the target server is a public web service.
Will appreciate your answers!
>

I have problem with Ultra Secure Memory Key Login Software (as non admin) hdlSrv.exe

I have problem with a memory key lenovo 1g. Here is a Company and the Users can't be Admin. So We have a big problem. I download "KeySafe II and MyKey in Non-Admin Mode" but its not run. I found in Lenovo pag, i installed as said in the instructions but i repeat I return to be normal user and couldn't use it in mode User! I trying and i saw that the service hdlsrv be on and run! but i can't. So ¿are there an archive that i can use and can use it this pendrive in Non-Admin mode?
We have SO Wxp
KeyLock : Ultra Secure Memory Key Login Software 1.0.3.6
Fru 45j5923
Lenovo 1g
Please!!! help Mee!!
thank u!

Jan 2, 2008 11:49:35 AM org.apache.coyote.http11.Http11Protocol init
INFO: Initializing Coyote HTTP/1.1 on http-8080
Jan 2, 2008 11:49:35 AM org.apache.catalina.startup.Catalina load
INFO: Initialization processed in 734 ms
Jan 2, 2008 11:49:35 AM org.apache.catalina.core.StandardService start
INFO: Starting service Catalina
Jan 2, 2008 11:49:35 AM org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/5.5.9
Jan 2, 2008 11:49:35 AM org.apache.catalina.realm.JDBCRealm start
SEVERE: Exception opening database connection
java.sql.SQLException: oracle.jdbc.driver.OracleDriver
     at org.apache.catalina.realm.JDBCRealm.open(JDBCRealm.java:684)
     at org.apache.catalina.realm.JDBCRealm.start(JDBCRealm.java:758)
     at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1004)
     at org.apache.catalina.core.StandardEngine.start(StandardEngine.java:442)
     at org.apache.catalina.core.StandardService.start(StandardService.java:450)
     at org.apache.catalina.core.StandardServer.start(StandardServer.java:683)
     at org.apache.catalina.startup.Catalina.start(Catalina.java:537)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:271)
     at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:409)
Jan 2, 2008 11:49:35 AM org.apache.catalina.core.StandardHost start
INFO: XML validation disabled
Jan 2, 2008 11:49:36 AM org.apache.catalina.core.StandardContext resourcesStart

Image loading problem with weblogic security page

I developed an j2ee application on tomcat server. After successful working in tomcat I migrated to weblogic server.
So problem is the application is working properly with out security in weblogic. Later security is added to the application, then the back ground images are not loading in .jsp pages. Please suggest me what i have to follow to display back ground images in the .jsp pages. I was unable to find solution.
Thanks
Ananda

Hi,
There is a BADI (TRIP_IMP_EXP) that can help you to restrict trip amount by set delimit date.
Use RESTRICT_TRAVEL_RANGE method ot do this.
BR, Jurijs

Problems with WEP Security?

Similar Messages

Maybe you are looking for