Problems with WRT300n & WPC300n
Hi guys!
I have a problem. I am reviewing the two Linksys-thingys WRT300n & WPC300n for a pc-mag, and for the last 4 hours I have been all over the internet trying to get a clue...
First of all both items works (not well (low range/falls out once in a while), but there is a connection after all). My main prob is, that I cant get the WPC300n to go faster then 54 Mbps... In the Linksys-control it says Wide Channel: N/A... like this is just regular G-speed...?
I have tried to turn on all the encryptionfacilities but it doesnt help. All the drivers and firmware are the newest...
Any of you got a clue?
I'm having the same problem with the same equipment. I hope there is someone that can help us. PLEASE
Similar Messages
-
Encoding Problems with WRT300N V2
Hello guys,
i have following problem:
I have a WRT300n Router and it seems to have problems with WPA2 encoding. I have 2 different deviceses (a SMC Ethernet Bridge and a PS3) trying to connect to my Linksys wireless router. No chance in WPA2 mode but when I try in WEP-Mode, both devicec can connect to it.
Are there known encoding problems?
Any idea what i can do?It is able to use. But my router always drops the connection. WEP is no problem, but ... what about low security and Wirless N is not enabled ??
-
Media Extender Problem with WRT300N
I have the Linksys WRT300N wireless router. I am having problems using the wireless connection with my Xbox 360 and my PS3. The internet portions of the consoles works fine. Im running into problems when I try and use either one as a media extender. Both the PS3 and the Xbox 360 are using the wireless adapters. Ive made sure that my computer is set up for media sharing and that my Windows Firewall is configured correctly. Ive looked at the setting of the router but it seems pretty complex and I dont know what to change if anything to resolve the problem. Could anyone tell me what the setting should be on the router to enable media sharing?
I dont think that there is some settings on the router .... but you can follow this settings ....
Access router setup page ....
Please click on the tab "Application and gaming" and click on sub
tab "Port range forwarding"
1) On the first line in Application box type in "Xbox", in start box
type in 88, in end box type in 88, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
2) On the second line in Application box type in "Xbox", in start box
type in 3074, in end box type in 3074, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
3) Now save the settings
4) Once you return to the setup page, click on the tab "Administration"
and disable the UPNP and save the settings.
5) Now assign the given ip address on your xbox
ip address :- 192.168.1.20
subnet mask :- 255.255.255.0
default gateway :- 192.168.1.1
Please assign the dns address on the xbox
primary dns :- 4.2.2.2
secondary dns :- 192.168.1.1
6) Please try to test your xbox live. -
ok so I have a three story house and the modem is downstairs on the second floor then right there I have a Linksys WRT300N router and then that has four ports in the back for hardwire cables and I had comcamst (my isp) come and run a cable up to the third floor for my gaming pc because the wireless wasnt very good because I have thick walls. This worked great and then I got my ps3. I tried using wireless and it was slow so i now switch the cable between the two depending on what im using. I want to hardwire both of them so how would i do this? The problem I am having may have to do with the router but not sure. I have COD4 for PC and I always had problems with punkbuster and the servers kicking me. Now I have MW2 for the PS3 and I go to log on to online play but it just says "connecting to matchmaking server..." The servers are back online from what I hear, they came on this morning and plus this is not the same message people were getting for people who couldnt connect because of the server being taken down. If someone could help me hardwire both my PC and PS3 with my set up and help me with online issues I would be very happy thanks!
The cable you are using from the router to upstairs...Instead of that cable,Connect a switch to the router and connect your both the PS3 to the switch...it will work fine.
-
Hi, I'm having a lot of problems with the WTR54GS. Is there any way to use this on another router(ie cascading)? I've attempted to connect it to my existing cascaded router network to no avail. I have a small dead spot at home and also need a traveling access point. I figure this unit could pull double duty; it can fill in the dead spot when I am home and when I'm abroad, I can use it in a hotel room with my OQO. As I follow the on screen prompts, I notice a slight problem. It wants me to install the router between my modem and my computer. I all ready have a router installed there. Matter of fact, all of my equipment is made by Linksys, so I didn't think I'd have a problem. So far, nothing but problems. I attempted to install it on my second router with yet more problems.
What am I doing wrong?
Thanks.Hi Mickey Boy. I was hoping to solve two problems at once; the need for a traveling access point as well as solving the dead spot. I do know about the range expanders. My wireless network is secured. Saddly, the WTR54GS I've purchased is nonreturnable. I have to make do with what I have. Any help would be great. Thanks. The only thing I can really think of doing is cascading the router to my other one. However, I've tried numurous connections without any positive effect. I'm losing faith in Linksys. I've ordered a Dlink portable router for travel. A friend has it and it works perfectly. He brought it over today to show me how it works and I was thoroughly impressed. No matter the configuration, it worked without a hitch. Now I either need the Linksys WTR54GS as a cascaded access point or a glorified paperweight. If anyone has any idea how I can install this on to my existing WRT300N it would be awesome. Otherwise, I've wasted my money and I'll not hesitate to throw it out. Thanks!Message Edited by Raynentye on 05-07-200702:56 PM
-
I am trying to implement some kind of a server listening for requests. The listener part of the app, is a daemon thread that listens for connections and instantiates a handling daemon thread once it gets some. However, my problem is that i must be able to kill the listening thread at the user's will (say via a sto button). I have done this via the Sun's proposed way, by testing a boolean flag in the loop, which is set to false when i wish to kill the thread. The problem with this thing is the following...
Once the thread starts excecuting, it will test the flag, find it true and enter the loop. At some point it will LOCK on the server socket waiting for connection. Unless some client actually connects, it will keep on listening indefinatelly whithought ever bothering to check for the flag again (no matter how many times you set the damn thing to false).
My question is this: Is there any real, non-theoretical, applied way to stop thread in java safely?
Thank you in advance,
LeftyThis was one solution from the socket programming forum, have you tried this??
public Thread MyThread extends Thread{
boolean active = true;
public void run(){
ss.setSoTimeout(90);
while (active){
try{
serverSocket = ss.accept();
catch (SocketTimeoutException ste){
// do nothing
// interrupt thread
public void deactivate(){
active = false;
// you gotta sleep for a time longer than the
// accept() timeout to make sure that timeout is finished.
try{
sleep(91);
}catch (InterruptedException ie){
interrupt();
} -
Problem with Threads and a static variable
I have a problem with the code below. I am yet to make sure that I understand the problem. Correct me if I am wrong please.
Code functionality:
A timer calls SetState every second. It sets the state and sets boolean variable "changed" to true. Then notifies a main process thread to check if the state changed to send a message.
The problem as far I understand is:
Assume the timer Thread calls SetState twice before the main process Thread runs. As a result, "changed" is set to true twice. However, since the main process is blocked twice during the two calls to SetState, when it runs it would have the two SetState timer threads blocked on its synchronized body. It will pass the first one, send the message and set "changed" to false since it was true. Now, it will pass the second thread, but here is the problem, "changed" is already set to false. As a result, it won't send the message even though it is supposed to.
Would you please let me know if my understanding is correct? If so, what would you propose to resolve the problem? Should I call wait some other or should I notify in a different way?
Thanks,
B.D.
Code:
private static volatile boolean bChanged = false;
private static Thread objMainProcess;
protected static void Init(){
objMainProcess = new Thread() {
public void run() {
while( objMainProcess == Thread.currentThread() ) {
GetState();
objMainProcess.setDaemon( true );
objMainProcess.start();
public static void initStatusTimer(){
if(objTimer == null)
objTimer = new javax.swing.Timer( 1000, new java.awt.event.ActionListener(){
public void actionPerformed( java.awt.event.ActionEvent evt){
SetState();
private static void SetState(){
if( objMainProcess == null ) return;
synchronized( objMainProcess ) {
bChanged = true;
try{
objMainProcess.notify();
}catch( IllegalMonitorStateException e ) {}
private static boolean GetState() {
if( objMainProcess == null ) return false;
synchronized( objMainProcess ) {
if( bChanged) {
SendMessage();
bChanged = false;
return true;
try {
objMainProcess.wait();
}catch( InterruptedException e ) {}
return false;
}Thanks DrClap for your reply. Everything you said is right. It is not easy to make them alternate since SetState() could be called from different places where the state could be anything else but a status message. Like a GREETING message for example. It is a handshaking message but not a status message.
Again as you said, There is a reason I can't call sendMessage() inside setState().
The only way I was able to do it is by having a counter of the number of notifies that have been called. Every time notify() is called a counter is incremented. Now instead of just checking if "changed" flag is true, I also check if notify counter is greater than zero. If both true, I send the message. If "changed" flag is false, I check again if the notify counter is greater than zero, I send the message. This way it works, but it is kind of a patch than a good design fix. I am yet to find a good solution.
Thanks,
B.D. -
Problem with threads running javaw
Hi,
Having a problem with multi thread programming using client server sockets. The program works find when starting the the application in a console using java muti.java , but when using javaw multi.java the program doesnt die and have to kill it in the task manager. The program doesnt display any of my gui error messages either when the server disconnect the client. all works find in a console. any advice on this as I havent been able to understand why this is happening? any comment would be appreciated.
troy.troy,
Try and post a minimum code sample of your app which
does not work.
When using javaw, make sure you redirect the standard
error and standard output streams to file.
Graeme.Hi Graeme,
I dont understand what you mean by redirection to file? some of my code below.
The code works fine under a console, code is supposed to exit when the client (the other server )disconnects. the problem is that but the clientworker side of the code still works. which under console it doesnt.
public class Server{
ServerSocket aServerSocket;
Socket dianosticsSocket;
Socket nPortExpress;
ClientListener aClientListener;
LinkedList queue = new LinkedList();
int port = 0;
int clientPort = 0;
String clientName = null;
boolean serverAlive = true;
* Server constructor generates a server
* Socket and then starts a client threads.
* @param aPort socket port of local machine.
public Server(int aPort, String aClientName, int aClientPort){
port = aPort;
clientName = aClientName;
clientPort = aClientPort;
try{
// create a new thread
aServerSocket = new ServerSocket(port) ;
// connect to the nPortExpress
aClientListener = new ClientListener(InetAddress.getByName(clientName), clientPort, queue,this);
// aClientListener.setDaemon(true);
aClientListener.start();
// start a dianostic port
DiagnosticsServer aDiagnosticsServer = new DiagnosticsServer(port,queue,aClientListener);
// System.out.println("Server is running on port " + port + "...");
// System.out.println("Connect to nPort");
catch(Exception e)
// System.out.println("ERROR: Server port " + port + " not available");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Server port " + port + " not available", JOptionPane.ERROR_MESSAGE);
serverAlive = false;
System.exit(1);
while(serverAlive&&aClientListener.hostSocket.isConnected()){
try{
// connect the client
Socket aClient = aServerSocket.accept();
//System.out.println("open client connection");
//System.out.println("client local: "+ aClient.getLocalAddress().toString());
// System.out.println("client localport: "+ aClient.getLocalPort());
// System.out.println("client : "+ aClient.getInetAddress().toString());
// System.out.println("client port: "+ aClient.getLocalPort());
// make a new client thread
ClientWorker clientThread = new ClientWorker(aClient, queue, aClientListener, false);
// start thread
clientThread.start();
catch(Exception e)
//System.out.println("ERROR: Client connection failure");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Client connection failure", JOptionPane.ERROR_MESSAGE);
}// end while
} // end constructor Server
void serverExit(){
JOptionPane.showMessageDialog(null, "Server ","ERROR: nPort Failure", JOptionPane.ERROR_MESSAGE);
System.exit(1);
}// end class Server
*** connect to another server
public class ClientListener extends Thread{
InetAddress hostName;
int hostPort;
Socket hostSocket;
BufferedReader in;
PrintWriter out;
boolean loggedIn;
LinkedList queue; // reference to Server queue
Server serverRef; // reference to main server
* ClientListener connects to the host server.
* @param aHostName is the name of the host eg server name or IP address.
* @param aHostPort is a port number of the host.
* @param aLoginName is the users login name.
public ClientListener(InetAddress aHostName, int aHostPort,LinkedList aQueue,Server aServer) // reference to Server queue)
hostName = aHostName;
hostPort = aHostPort;
queue = aQueue;
serverRef = aServer;
// connect to the server
try{
hostSocket = new Socket(hostName, hostPort);
catch(IOException e){
//System.out.println("ERROR: Connection Host Failed");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Connection to nPort Failed", JOptionPane.ERROR_MESSAGE);
System.exit(0);
} // end constructor ClientListener
** multi client connection server
ClientWorker(Socket aSocket,LinkedList aQueue, ClientListener aClientListener, boolean diagnostics){
queue = aQueue;
addToQueue(this);
client = aSocket;
clientRef = aClientListener;
aDiagnostic = diagnostics;
} // end constructor ClientWorker
* run method is the main loop of the server program
* in change of handle new client connection as well
* as handle all messages and errors.
public void run(){
boolean alive = true;
String aSubString = "";
in = null;
out = null;
loginName = "";
loggedIn = false;
while (alive && client.isConnected()&& clientRef.hostSocket.isConnected()){
try{
in = new BufferedReader(new InputStreamReader(client.getInputStream()));
out = new PrintWriter(new OutputStreamWriter(client.getOutputStream()));
if(aDiagnostic){
out.println("WELCOME to diagnostics");
broadCastDia("Connect : diagnostics "+client.getInetAddress().toString());
out.flush();
else {
out.println("WELCOME to Troy's Server");
broadCastDia("Connect : client "+client.getInetAddress().toString());
out.flush();
String line;
while(((line = in.readLine())!= null)){
StringTokenizer aStringToken = new StringTokenizer(line, " ");
if(!aDiagnostic){
broadCastDia(line);
clientRef.sendMessage(line); // send mesage out to netExpress
out.println(line);
out.flush();
else{
if(line.equals("GETIPS"))
getIPs();
else{
clientRef.sendMessage(line); // send mesage out to netExpress
out.println(line);
out.flush();
} // end while
catch(Exception e){
// System.out.println("ERROR:Client Connection reset");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR:Client Connection reset", JOptionPane.ERROR_MESSAGE);
try{
if(aDiagnostic){
broadCastDia("Disconnect : diagnostics "+client.getInetAddress().toString());
out.flush();
else {
broadCastDia("Disconnect : client "+client.getInetAddress().toString());
out.flush();
// close the buffers and connection;
in.close();
out.close();
client.close();
// System.out.println("out");
// remove from list
removeThreadQueue(this);
alive = false;
catch(Exception e){
// System.out.println("ERROR: Client Connection reset failure");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Client Connection reset failure", JOptionPane.ERROR_MESSAGE);
}// end while
} // end method run
* method run - Generates io stream for communicating with the server and
* starts the client gui. Run also parses the input commands from the server.
public void run(){
boolean alive = true;
try{
// begin to life the gui
// aGuiClient = new ClientGui(hostName.getHostName(), hostPort, loginName, this);
// aGuiClient.show();
in = new BufferedReader(new InputStreamReader(hostSocket.getInputStream()));
out = new PrintWriter(new OutputStreamWriter(hostSocket.getOutputStream()));
while (alive && hostSocket.isConnected()){
String line;
while(((line = in.readLine())!= null)){
System.out.println(line);
broadCast(line);
} // end while
} // end while
catch(Exception e){
// System.out.println("ERRORa Connection to host reset");
JOptionPane.showMessageDialog(null, (e.toString()),"ERROR: Connection to nPort reset", JOptionPane.ERROR_MESSAGE);
try{
hostSocket.close();
}catch(Exception a){
JOptionPane.showMessageDialog(null, (a.toString()),"ERROR: Exception", JOptionPane.ERROR_MESSAGE);
alive = false;
System.exit(1);
} // end method run -
Problem with threads and camera.
Hi everybody!
I've a problem with taking snapshot.
I would like to display a loading screen after it take snapshot ( sometimes i
have to wait few seconds after i took snapshot. Propably photo is being taken in time where i have to wait).
I was trying to use threads but i didn't succeed.
I made this code:
display.setCurrent(perform);
new Thread(new Runnable(){
public void run() {
while((!performing.isShown()) && (backgroundCamera.isShown())){
Thread.yield();
notifyAll();
}).start();
new Thread(new Runnable(){
public void run() {
try {
this.wait();
} catch(Exception e) {
exceptionHandler(e);
photo = camera.snapshot();
display.setCurrent(displayPhoto);
}).start();This code is sometimes showing performing screen but sometimes no.
I don't know why. In my opinion performing.isShown() method isn't working correctly.
Does anyone have some idea how to use threads here?Hi,
I've finally managed to work this fine.
The code:
Object o = new Object();
display.setCurrent(perform);
new Thread(new Runnable(){
public void run() {
while(!performing.isShown()){
Thread.yield();
synchronized(o) {
o.notify();
}).start();
new Thread(new Runnable(){
public void run() {
try {
synchronized(o) {
o.wait(1);
} catch(Exception e) {
exceptionHandler(e);
photo = camera.snapshot();
display.setCurrent(displayPhoto);
}).start(); -
We have a problem where our application stops responding after a few days of usage. Things will for fine for a day or two, and then pretty quickly threads will start getting hung up, usually in places where they are allocating memory
We are running WebLogic 8.1 SP2 on Sun JDK 1.4.2_04 on Solaris 8 using the alternate threading model and the -server hotspot vm. We are running pretty much the same code that we had no problems with under WebLogic 6.1 SP4 and Sun JDK 1.3.1.
A thread dump usually shows that some or all of our execute threads are in the state "waiting for monitor entry" even though they are not currently waiting on any java locks. Here is a sample thread from the thread dump (we have ~120 threads so I don't want to post the full dump).
=============================================================================================
"ExecuteThread: '8' for queue: 'itgCrmWarExecutionQueue'" daemon prio=5 tid=0x005941d0 nid=0x2c waiting for monitor entry [c807f000..c807fc28]
at java.lang.String.substring(String.java:1446)
at java.lang.String.substring(String.java:1411)
at weblogic.servlet.internal.ServletRequestImpl.getRelativeUri(ServletRequestImpl.java:1872)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3492)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
=============================================================================================
String.java line 1446 for this jdk allocates a new String object, and all the other threads in this state also are creating new objects or arrays, etc.
We've done a pstack on this process when it's in this state, and the threads that are in the "waiting for monitor entry" that look like they're allocating memory are all waiting on the same lwp_mutex_lock with some allocation method that's calling into the native TwoGenerationCollectorPolicy.mem_allocate_work (see pstack output below for the same thread as in the thread dump above)
=============================================================================================
----------------- lwp# 44 / thread# 44 --------------------
ff31f364 lwp_mutex_lock (e3d70)
fee92384 __1cNObjectMonitorGenter26MpnGThread__v_ (5000, 525c, 5000, 50dc, 4800, 4af0) + 2d8
fee324d4 __1cSObjectSynchronizerKfast_enter6FnGHandle_pnJBasicLock_pnGThread__v_ (c807f65c, c807f7d4, 5941d0, 0, 35d654, fee328ec) + 68
fee32954 __1cQinstanceRefKlassZacquire_pending_list_lock6FpnJBasicLock__v_ (c807f7d4, ff170000, d4680000, 4491d4, fee1bc2c,
0) + 78
fee3167c __1cPVM_GC_OperationNdoit_prologue6M_i_ (c807f7bc, 4400, ff170000, 2d2b8, 4a6268, c807fa18) + 38
fee2e0b0 __1cIVMThreadHexecute6FpnMVM_Operation__v_ (c807f7bc, 963a8, 0, 0, 1, 0) + 90
fed2c2a4 __1cbCTwoGenerationCollectorPolicyRmem_allocate_work6MIii_pnIHeapWord__ (962c0, ff1c29ec, ff1c297c, ff131a26, 4800, 4998) + 160
fed22940 __1cNinstanceKlassRallocate_instance6MpnGThread__pnPinstanceOopDesc__ (ee009020, 5941d0, 15ca581, 3647f0, 4a6268, c807f8c8) + 180
fed34928 __1cLOptoRuntimeFnew_C6FpnMklassOopDesc_pnKJavaThread__v_ (ee009018, 5941d0, 0, 0, 0, 0) + 28
fa435a58 ???????? (ee009018, e86de, 15ca4de, 50dc, 5941d0, c807f9c8)
fb36f9a4 ???????? (0, d412ccd8, ee046c28, ff170000, 0, 0)
fad8b278 ???????? (ee046c28, d6000c90, ee046530, 8, db8e8450, c807f9e8)
fad62abc ???????? (d412ccd8, ee046530, d6000c90, ee3bfa38, 8, c807fa18)
fa4b3c38 ???????? (c807fb9c, 0, f2134700, fa415e50, 8, c807faa8)
fa40010c ???????? (c807fc28, c807fe90, a, ee9e1e20, 4, c807fb40)
fed5d48c __1cJJavaCallsLcall_helper6FpnJJavaValue_pnMmethodHandle_pnRJavaCallArguments_pnGThread__v_ (c807fe88, c807fcf0, c807fda8, 5941d0, 5941d0, c807fd00) + 27c
fee4b784 __1cJJavaCallsMcall_virtual6FpnJJavaValue_nLKlassHandle_nMsymbolHandle_4pnRJavaCallArguments_pnGThread__v_ (ff170000, 594778, c807fd9c, c807fd98, c807fda8, 5941d0) + 164
fee5e8dc __1cJJavaCallsMcall_virtual6FpnJJavaValue_nGHandle_nLKlassHandle_nMsymbolHandle_5pnGThread__v_ (c807fe88, c807fe84, c807fe7c, c807fe74, c807fe6c, 5941d0) + 6c
fee6fc74 __1cMthread_entry6FpnKJavaThread_pnGThread__v_ (5941d0, 5941d0, 838588, 594778, 306d10, fee69254) + 128
fee6927c __1cKJavaThreadDrun6M_v_ (5941d0, 2c, 40, 0, 40, 0) + 284
fee6575c _start (5941d0, fa1a1600, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Also when it's having this problem, the "VM Thread" is always using a lot of processor time. We did a couple of pstacks today while it was having this problem, and this thread was stuck in the ONMethodSweeper.sweep for over 15 minutes when we finally killed the server.
From the thread dump:
"VM Thread" prio=5 tid=0x000e2d20 nid=0x2 runnable
From the first pstack:
=============================================================================================
----------------- lwp# 2 / thread# 2 --------------------
fed40c04 __1cXvirtual_call_RelocationIparse_ic6FrpnICodeBlob_rpC5rppnHoopDesc_pi_nNRelocIterator__ (42a2f4, fa5fa46d, ffffffff, fc4ffcb8, 42a2f4, 42a324) + 124
fed46318 __1cKCompiledIC2t5B6MpnKRelocation__v_ (42a2f0, fc4ffd24, fc4ffd4c, e802, 0, 6) + 38
fed90c38 __1cHnmethodVcleanup_inline_caches6M_v_ (fa5f7f88, fa608940, 1, 0, fa400000, 6) + 1ac
fede18b4 __1cONMethodSweeperFsweep6F_v_ (2cf38, 0, ffffffff, ff1cf1fc, ff1c66e8, fede1d44) + 1b0
fede1e6c __1cUSafepointSynchronizeFbegin6F_v_ (2cf38, ff1ba138, 5000, 50dc, 5000, 525c) + 248
feef1fd4 __1cIVMThreadEloop6M_v_ (4400, 4000, 4324, 4000, 42b0, 3800) + 3d4
feef1ae4 __1cIVMThreadDrun6M_v_ (e2d20, 2, 40, 0, 40, 0) + 8c
fee6575c _start (e2d20, ff270200, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Second pstack
=============================================================================================
----------------- lwp# 2 / thread# 2 --------------------
fed41180 __1cXvirtual_call_RelocationIparse_ic6FrpnICodeBlob_rpC5rppnHoopDesc_pi_nNRelocIterator__ (0, ff1b9664, ffffffff, fc4ffcb8, a6f2cc, fc4ffbd0) + 6a0
fed46318 __1cKCompiledIC2t5B6MpnKRelocation__v_ (a6f2c8, fc4ffd24, fc4ffd4c, e802, 0, 6) + 38
fed90c38 __1cHnmethodVcleanup_inline_caches6M_v_ (faded4c8, fadf2c80, 1, 0, fa400000, 6) + 1ac
fede18b4 __1cONMethodSweeperFsweep6F_v_ (2cf38, 0, ffffffff, ff1cf1fc, ff1c66e8, fede1d44) + 1b0
fede1e6c __1cUSafepointSynchronizeFbegin6F_v_ (2cf38, ff1ba138, 5000, 50dc, 5000, 525c) + 248
feef1fd4 __1cIVMThreadEloop6M_v_ (4400, 4000, 4324, 4000, 42b0, 3800) + 3d4
feef1ae4 __1cIVMThreadDrun6M_v_ (e2d20, 2, 40, 0, 40, 0) + 8c
fee6575c _start (e2d20, ff270200, 0, 0, 0, 0) + 134
ff3758c0 lwpstart (0, 0, 0, 0, 0, 0)
=============================================================================================
Has anyone ever seen anything like this? I'm trying to figure out if this is caused by something we're doing, or something relating to our environment and jvm options. Any ideas?Thanks for the reply - I'm testing our app with the +UseConcMarkSweepGC now in our test environment to make sure it doesn't cause any problems there. Unfortunately the only place we've had this problem is on the production server, so it's extra difficult debugging this.
We're using the following memory options:
-ms512m -mx512m -XX:NewSize=128m -XX:PermSize=192m -XX:MaxNewSize=128m -XX:MaxPermSize=192m -XX:SurvivorRatio=8and the following debugging options, as we've also been seeing OutOfMemoryErrors ( see http://forum.java.sun.com/thread.jsp?forum=37&thread=522354&tstart=45&trange=15 )
-verbosegc -XX:+PrintGCDetails -XX:+PrintGCTimeStamps -XX:+PrintHeapAtGCBTW, which c++filt version and options are you using? Our Solaris boxes only seem to have the GNU version installed. I was trying to run that on some of the other stack traces and wasn't getting anywhere, and didn't know if because it was GNU version wouldn't work on something compiled with the Sun compiler.
Thanks!
--Andy -
Problem with threads and ProgressMonitor
Dear Friends:
I have a little problem with a thread and a ProgressMonitor. I have a long time process that runs in a thread (the thread is in an separate class). The thread has a ProgressMonitor that works fine and shows the tasks progress.
But I need deactivate the main class(the main class is the user interface) until the thread ends.
I use something like this:
LongTask myTask=new LongTask();
myTask.start();
myTask.join();
Now, the main class waits for the task to end, but the progress monitor don`t works fine: it shows only the dialog but not the progress bar.
What's wrong?Is the dialog a modal dialog? This can block other UI updates.
In general, you should make sure that it isn't modal, and that your workThread has a fairly low priority so that the UI can do its updating -
Problem with threads and/or memory
I'm developing an application where there are 3 threads. One of them sends a request to the other, and if the 2nd can't answer it, it sends it to the 3rd (similar to CPU -> CACHE -> MEMORY). When i run the program with 1000-10.000 requests, no problem occurs. When i run it with 300.000-1.000.000 requests, it sometimes hangs. Is this a problem with the garbage collector, or should it be related to the threads mecanism.
(note: eache thread is in execution using a finite state machine)i had been running the program inside Netbeans.
Running the jar using the command line outside
Netbeans i have no more problems... Does Netbeans use
it's own JVM?Depends how you set it up, but look under the options. There are settings for the compiler and jvm that it uses. -
Installation problem with NW'04 SR1: database connection failed
Hi all,
while installing NW '04 SR1 on Windows Server 2003 SP1 and MS SQL Server 2000 SP4 I ran into an error related to the database connection. While performing the step "Load Java Database content" SAPinst crashes with the message
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
The connection to the SLQ Server with e.g. the Query Analyzer is OK. I had a problem with this installation setup before (have a look at the corresponding <a href="https://forums.sdn.sap.com/thread.jspa?threadID=338638&tstart=0">thread</a> ), the JDBC drivers where missing on the installation master but after copying them in the right direction the installation went on with no problem up to this point...
Has anybody an idea what could have happened here? Is this maybe a problem connected to the one I recently had
Below I attached the sapinst.log and jload.log with more detailed messages.
sapinst.log ###########
INFO 2007-03-12 22:06:24
Working directory changed to C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_~1\ONE_HOST.
INFO 2007-03-12 22:06:24
Output of D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log' is written to the logfile C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_~1\ONE_HOST/jload.java.log.
WARNING 2007-03-12 22:06:26
Execution of the command "D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log'" finished with return code 1. Output:
java version "1.4.2_13"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_13-b06)
Java HotSpot(TM) Client VM (build 1.4.2_13-b06, mixed mode)
12.03.2007 22:06:25 com.sap.inst.jload.Jload main
INFO: Jload -sec WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key -dataDir S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP -job C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML -log C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log
12.03.2007 22:06:26 com.sap.inst.jload.Jload main
SCHWERWIEGEND: couldn't connect to DB
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
ERROR 2007-03-12 22:06:26
CJS-20065 Execution of JLoad tool 'D:\Java/bin/java.exe '-classpath' './sharedlib/antlr.jar;./sharedlib/exception.jar;./sharedlib/jddi.jar;./sharedlib/jload.jar;./sharedlib/logging.jar;./sharedlib/offlineconfiguration.jar;./sharedlib/opensqlsta.jar;./sharedlib/tc_sec_secstorefs.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\base.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\util.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\sqlserver.jar;D:\usr\sap/WPT/JC10/j2ee\jdbc\spy.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jce_export.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_jsse.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_smime.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/iaik_ssl.jar;D:/usr/sap/WPT/SYS/global/security/lib/tools/w3c_http.jar' '-showversion' '-Xmx512m' 'com.sap.inst.jload.Jload' '-sec' 'WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key' '-dataDir' 'S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP' '-job' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML' '-log' 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log'' aborts with returncode 1. Check 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log' and 'C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.java.log' for more information.
jload.log ###########
12.03.07 22:06 com.sap.inst.jload.Jload main
INFO: Jload -sec WPT,jdbc/pool/WPT,D:\usr\sap\WPT\SYS\global/security/data/SecStore.properties,D:\usr\sap\WPT\SYS\global/security/data/SecStore.key -dataDir S:/D51030724\J2EE_OSINDEP\J2EE-ENG/JDMP -job C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/IMPORT.XML -log C:\PROGRA1\SAPINS1\NW04SR1\WEBAS_1\ONE_HOST/jload.log
12.03.07 22:06 com.sap.inst.jload.Jload main
SEVERE: couldn't connect to DB
com.sap.sql.log.OpenSQLException: Could not load class com.ddtek.jdbc.sqlserver.SQLServerDriver.
Best regards,
BerndHello Kairat,
Please follow the below mentioned guide to install it.
Check all the parameters to set and run pre requisite checker before starting installation.
Keep in mind that before starting any SAP installation you should always run prerequisite checker.
https://websmp205.sap-ag.de/instguides --> SAP Netweaver -->SAP Netweaver 7.0 -- > Installations --> EHP2
Regards,
Amit Barnawal -
My app store wont let me download apps, asks me to update my payment details then says theres a problem with previous purchase and card is expired which is untrue someone help me pls
This is a User to User Forum...
See Here for
Mac Apps Store Customer Service
http://www.apple.com/support/mac/app-store/contact.html?form=account
iTunes Customer Service Contact
http://www.apple.com/support/itunes/contact.html -
Problem with item and/or data during page-processing-PS/SQL
Greetings!
On my page I have a custom report (from 2 tables) and a small form-field, that adds and edits data in the report. After generating the form with the wizard I added an extra item, to store the id from one of the tables from the report data.
Now, on submit a calculation should take place, that updates data according user input with a procedure in Page-Prosseses:
declare a number;
begin
case :PLATZ
when 1 then a:=100;
when 2 then a:= 50;
else a:=25;
end case;
update TBL_MITGLIEDER set TURNIERPUNKTE = TURNIERPUNKTE + a
where ID_MITGL = :P14_ID_MITGL;
end;
:PLATZ is user selected (1,2,3), :P14_ID_MITGL stores the reference to TBL_MITGLIEDER (and shows the change, when I select another record)
As I understand, that process should also run, when I submit a chance, but nothing happens then.
But when I try to save a new record (which worked without any problems before adding that process), I get this error message:
ORA-06550: line 1, column 64: PL/SQL: ORA-00957: duplicate column name ORA-06550: line 1, column 7: PL/SQL: SQL Statement ignored
Error Unable to process row of table TBL_TURNIERSIEGER.
Then, when I go back into the app-builder and try to run the page again, I get this message:
ORA-01403: no data found
Error Unable to fetch row.
I am not sure, if you guys have all the information you need, to know whats going on. Maybe this has to do with session-id and the whay, items are updated. I hope you can help me.
Thanks, best regards,
tobiFirst can you please post all log file errors
>> I can't really give you a solution or specific recommendation since I did not saw this error yet myself, but on your own risk you can try:
1. You may try to just register 'dts.dll' using regsvr32.exe, but this error may indicate a bigger problem with setup.
If you are running SQL Server 64bit then try running this at the command prompt: %windir%\syswow64\regsvr32 "%ProgramFiles(x86)%\Microsoft SQL Server\90\dts\binn\dts.dll"
2. You can try reinstall from start (In this case you have to make sure that you un-install all)
[Personal Site] [Blog] [Facebook]
Maybe you are looking for
-
How does apex detect the MIMETYPE of an upload?
Hello, I need to import a bunch of files from the OS filesystem to my own table (blob). For implementing the download of these files I need to know the mimetype. Now, the files are stored in my table, but I have no clue how to detect the mimetype of
-
OK guys, I'm struggling. I've watched the on-line tutorials, read the white papers (especially "Naming Standardization"), and looked through the help pages. There are so many options for controlling naming that I think I'm lost in the trees trying to
-
Typing Devanagari on Mac OS Yosemite
HI. I need to write devanagari on my Microsoft Word for Mac. In other OS you would go to system preferences/international/input menu. but now I can't find the "International" anymore under System Preferences. Can somebody help me? Thanks
-
I have an iMac 11,3 (3.2 GHz i3, 8GB RAM, 1TB HDD). I would like to know if anyone has encountered any issues with creating 3 partitions on one drive. Has there been any lowered performance? Ideally, I'd like to have one partition devoted to Lion or
-
This happens quite often. I "x" out the browser when I am at a banking site, etc and when I try to re-open Firefox the message clearly states: "Firefox is already running and you must close it before you can open a browser and/or you must re-start yo