Problems with WRT54G and Call of Duty 4 hosts....XBOX360

I have a WRT54G wireless router and an xbox360 hooked up wirelessly to it using the wireless adapter made my microsoft for the 360. The problem is that it is nearly impossible for me to connect to ANY host at all. My internet works fine and I dont have this problem with other games. I'm wondering if anyone can help me out with this. My isp is Verizon DSL, i have a Westell 5100 modem, that is about all else I can think of that may have any importance. Thank you for the help in advance.

Check the firmware of the router ... if possible upgrade the firmware .... Also try to forward the ports on the router setup page ..

Similar Messages

Problem with WRT54G and DSL NAT router

I have a WRT54G connected to a Westell DSL NAT router. I would like to be able to allow incoming connections to my FreeBSD server.
The Westell router allows me to set IP Passthrough (they call it "Single Static IP"). This gives the WRT54G the outside IP address given to the DSL router. I can then set up the WRT54G for DDNS and port forwarding to forward specific ports I want to my server.
This works, for about 2-3 days. Then, I start to randomly lose outside connectivity. Web pages start coming up with missing elements, or taking a long time to load. This will eventually lead to total loss of outgoing communication.
Normally, I would blame this on the Westell NAT router, but as I'm losing connectivity to the internet, I'm also losing connectivity to the WRT54G. It will try to load configuration pages but will be slow with missing elements, etc.
All communications between computers on my inside network continue to function properly, it's just connectivity to the WRT54G and the internet that seem to start to fail.
Does anyone have any idea what is going on? I just upgraded the firmware on the WRT54G from 1.01.1 to 1.02.0, but I don't imagine this will help.
Thanks,
David Chamberlain

Try setting the MTU to manual and change the value to 1450
"Only those who risk going too far can possibly find out how far one can go..."

Problem with messages and calls,, please respond

Problem with my iphone is that the messages are sent and received very late, it hangs while sending, when delete a message it takes time to open messages firstly... messages in the thread disappear and such abnormalities.
and in Calls, i receive notification when the call is missed.
help!

I would do a full restore using iTunes (backup first, of course)

Problem with messages and calls

Problem with my iphone is that the messages are sent and received very late, it hangs while sending, when delete a message it takes time to open messages firstly... messages in the thread disappear and such abnormalities.
and in Calls, i receive notification when the call is missed.
help!

Ritu Parchure wrote:
I have ulmocked and restored the iphone.
I assume you mean "unlocked and restored." My apologies if I msunderstand, but if you unlocked it yourself, then you must have hacked it. If it was originally locked at the time of purchase, only that carrier can unlock it.

Problem with sound in Call of Duty 2

I bought Call of Duty 2 while my grandfather was buying a new iMac. We brought it home, set it up, and CoD 2 worked fantastically on his computer. I brought it home to my older iMac G5, and tried to set it up. The graphics are fine, the gameplay is there, but the only audio that plays is the background music and environmental sounds (wind, distant gunfire, etc.). No gameplay sounds (gunfire, voices, footsteps, etc.) can be heard. I read up on this in the forums, where people had solved the same problem by going to Audio MIDI Support in Applications/Utilities and changing audio output to 44,1000 Hz 2ch. I tried doing the same thing, but the audio output pane in the MIDI support app only said "output not supported". How can I fix this? Please help!
iMac G5 2 GHz, 512 MB RAM Mac OS X (10.4.9)

Hi
In Audio MIDI Setup, change Properties For to Built-in Output. It will then change from Output Not Supported to Input Not Supported & the Output bit will become active.
Another way of restoring sounds is to open GarageBand, play a few notes on the screen keyboard, then quit GarageBand.
Steve

Problem with ALV_GRID and CALL TRANSACTION.

Hi all, Could you please tell me
At SE38
Why REUSE_ALV_GRID_DISPLAY and CALL TRANSACTION after called then I click the back button to return to the calling program but it automatic return to the source code? (it hasn't saves the data in alv grid )
In another case of this program, after automatic return to the source code then I have to waiting for 5-10 mins for execute again cuz if immediately execute the program don't fill any data to the alv grid.
I have problem with a simple source code like this
REPORT ZFS_ALV_DEMO.
TYPE-POOLS: slis.
DATA: itab LIKE STANDARD TABLE OF aufk WITH HEADER LINE.
DATA: gs_selfield TYPE slis_selfield   "Information cursor position ALV
    , w_aufnr     LIKE aufk-aufnr.     "Order Number
SELECT * FROM aufk INTO TABLE itab WHERE autyp = 40.     "//Process Order
CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
     EXPORTING
          i_structure_name        = 'aufk'
          i_callback_program      = sy-cprog
          i_callback_user_command = 'USER_COMMAND_COR3'
     TABLES
          t_outtab         = itab
     EXCEPTIONS
          program_error    = 1
          OTHERS           = 2.
FORM user_command_cor3 USING u_ucomm     LIKE sy-ucomm
                             us_selfield TYPE slis_selfield."#EC CALLED
CASE u_ucomm.
    WHEN '&IC1'.
      gs_selfield = us_selfield.
      IF gs_selfield-fieldname = 'AUFNR'.
        SET PARAMETER ID 'ANR' FIELD gs_selfield-value.
        CALL TRANSACTION 'COR3' AND SKIP FIRST SCREEN.
      ELSE.
        MESSAGE w208(00) WITH 'Select by Order only!'.
      ENDIF.
ENDCASE.
ENDFORM.

Hi all, Could you please tell me
At SE38
Why REUSE_ALV_GRID_DISPLAY and CALL TRANSACTION after called then I click the back button to return to the calling program but it automatic return to the source code? (it hasn't saves the data in alv grid )
In another case of this program, after automatic return to the source code then I have to waiting for 5-10 mins for execute again cuz if immediately execute the program don't fill any data to the alv grid.
I have problem with a simple source code like this
REPORT ZFS_ALV_DEMO.
TYPE-POOLS: slis.
DATA: itab LIKE STANDARD TABLE OF aufk WITH HEADER LINE.
DATA: gs_selfield TYPE slis_selfield   "Information cursor position ALV
    , w_aufnr     LIKE aufk-aufnr.     "Order Number
SELECT * FROM aufk INTO TABLE itab WHERE autyp = 40.     "//Process Order
CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
     EXPORTING
          i_structure_name        = 'aufk'
          i_callback_program      = sy-cprog
          i_callback_user_command = 'USER_COMMAND_COR3'
     TABLES
          t_outtab         = itab
     EXCEPTIONS
          program_error    = 1
          OTHERS           = 2.
FORM user_command_cor3 USING u_ucomm     LIKE sy-ucomm
                             us_selfield TYPE slis_selfield."#EC CALLED
CASE u_ucomm.
    WHEN '&IC1'.
      gs_selfield = us_selfield.
      IF gs_selfield-fieldname = 'AUFNR'.
        SET PARAMETER ID 'ANR' FIELD gs_selfield-value.
        CALL TRANSACTION 'COR3' AND SKIP FIRST SCREEN.
      ELSE.
        MESSAGE w208(00) WITH 'Select by Order only!'.
      ENDIF.
ENDCASE.
ENDFORM.

Problem with noise and call dropping

Ever since I got the new BT Internet infinity I've seem to be having problems with my telephone line.
At times I can hear feedback when I'm on the phone, at times I can hear myself talk back or I can hear a buzzing sound. Also now my phone doesn't seem to ring and if they do after one ring it will show the phone is connected when nobody has picked up the handset. It drops after one ring, The caller display doesn't work, I have two telephones one upstairs and downstairs having the same problem, the upstairs telephone the ring isn't consistent and both phones are out of sync
Not sure what is going on here and I'm sure that there isn't anything wrong at my side of things
I was told that an engineer needs to be booked and if there are any problems found inside the house I would be charged 99Pounds? For starters your own person came to install the equipment ever since then I've been having this issue.
Would like to know if this has happened to anyone and what they did ?
Kindest Regards
Jashoda Kerai

they advise all callers that as some faults are the users equipment or internal wiring you problem sound like one that would be no charge BT only charge if the fault is found after the Master socket
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Problems with WRT54GS and EasyLink after adding Comcast Digital Voice.

I had a working network. Cable modem (Comcast), WRT54GS, 2 wired PCs (one XP/SP3, one Vista Home Edition SP1), 2 wireless laptop PCs (one XP/SP3, one Vista Home Edition SP1) and a HP OfficeJet 7210 printer (connected to WRT54GS as network printer). Everything was fine and worked.
Then, I added Comcast Digital Voice. Obviously, they switched the cable modem for a new cable modem with the phone service option. Now, I can't print to the OfficeJet from the wired Vista PC, and EasyLink displays "initializing" for as long as I'll wait (5+ minutes).
I finally have to kill EasyLink from the TaskManager. Any help or ideas appreciated!
Solved!
Go to Solution.

I solved the problem. It turns out the new cable modem and problem with EasyLink initializing were "red herrings".
The problem turned out to be a classic network problem! The hard-wired Vista PC had the wrong IP address. The wireless XP PC had the printer configured by network name instead of network (i.e. IP) address.
When I deleted the printer on the Vista PC and re-added it with the correct address everything worked fine.
Apparently the printer got a new IP address from the server on the WRT54GS after the installation of the new modem. Also, it looks like Vista doesn't report a communication error for a network printer, but does for a USB direct connect.

Problems with texting and calling

Hi!
I have a problem with my phone, I just got it 2:nd hand so I do not know if it worked properly earlier.
I can't call anyone, the phone just disconnects and says "beep beep beep".
People calling me goes straight to voicemail.
I can not send or receive test messages unless it is iMessage.
3G data traffic works properly though, any thoughts? I have restored the entire phone 2 times and the network settings 2 times and it is still the same problem. When I tried to use the SIM-card on my old phone (android) it works as espected.

Your second-hand phone may have been hacked or jailbroken before you got it. Ask the person you bought it from.

[HELP] Problem with restore and recovery to new host

Hi, guys!
I have been trying for two days, but still cannot get it to work.
I have taken a full hot(online) backup with archive logs as well as the control file and SPFILE, and then copied the backup to the new host with the same directory structure and settings. Finally, I have tried to restore & recover the database on the new host but failed during the restore process.
Both the original host and the new host have the same Oracle installed down to the patch level. I couldn't figure out the proper solution to this problem base on my limited knowledge about Oracle DB.
Could anyone help me out here? Any advice would be appreciated!
RMAN> restore database until sequence 10 thread 1;
Starting restore at 08-NOV-11
using channel ORA_DISK_1
channel ORA_DISK_1: starting datafile backupset restore
channel ORA_DISK_1: specifying datafile(s) to restore from backup set
restoring datafile 00001 to D:\DBDATA\PRODDB\SYSTEM01.DBF
restoring datafile 00002 to D:\DBDATA\PRODDB\UNDOTBS01.DBF
restoring datafile 00003 to D:\DBDATA\PRODDB\SYSAUX01.DBF
restoring datafile 00004 to D:\DBDATA\PRODDB\USERS01.DBF
restoring datafile 00005 to D:\ORA_DATADATA01.DBF
restoring datafile 00006 to D:\ORA_DATA\DATA02.DBF
restoring datafile 00007 to D:\ORA_DATA\INDX01.DBF
restoring datafile 00008 to D:\ORA_DATA\INDX02.DBF
channel ORA_DISK_1: reading from backup piece C:\ORACLE\PRODUCT\10.2.0\FLASH_REC
OVERY_AREA\PRODDB\BACKUPSET\2011_11_07\O1_MF_NNNDF_TAG20111107T175037_7CH6YYVJ_.BK
P
failover to previous backup
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of restore command at 11/08/2011 11:41:33
RMAN-06026: some targets not found - aborting restore
RMAN-06023: no backup or copy of datafile 4 found to restore
RMAN-06023: no backup or copy of datafile 3 found to restore
RMAN-06023: no backup or copy of datafile 2 found to restore
RMAN-06023: no backup or copy of datafile 1 found to restore
Here is some extra information that you might want to know about:
RMAN> list incarnation;
List of Database Incarnations
DB Key Inc Key DB Name DB ID STATUS Reset SCN Reset Time
1 1 PRODDB 3774691295 PARENT 1 17-APR-07
2 2 PRODDB 3774691295 PARENT 521803 06-OCT-11
3 3 PRODDB 3774691295 PARENT 1595143 20-OCT-11
4 4 PRODDB 3774691295 PARENT 1600974 20-OCT-11
5 5 PRODDB 3774691295 PARENT 1952053 27-OCT-11
6 6 PRODDB 3774691295 CURRENT 2146951 07-NOV-11
RMAN> list backup recoverable;
List of Backup Sets
===================
BS Key Type LV Size Device Type Elapsed Time Completion Time
37 Full 822.34M DISK 00:29:47 07-NOV-11
BP Key: 37 Status: AVAILABLE Compressed: NO Tag: TAG20111107T175037
Piece Name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\BACKUPSET\
2011_11_07\O1_MF_NNNDF_TAG20111107T175037_7CH6YYVJ_.BKP
List of Datafiles in backup set 37
File LV Type Ckp SCN Ckp Time Name
1 Full 2149673 07-NOV-11 D:\DBDATA\PRODDB\SYSTEM01.DBF
2 Full 2149673 07-NOV-11 D:\DBDATA\PRODDB\UNDOTBS01.DBF
3 Full 2149673 07-NOV-11 D:\DBDATA\PRODDB\SYSAUX01.DBF
4 Full 2149673 07-NOV-11 D:\DBDATA\PRODDB\USERS01.DBF
5 Full 2149673 07-NOV-11 D:\ORA_DATA\DATA01.DBF
6 Full 2149673 07-NOV-11 D:\ORA_DATA\DATA02.DBF
7 Full 2149673 07-NOV-11 D:\ORA_DATA\INDX01.DBF
8 Full 2149673 07-NOV-11 D:\ORA_DATA\INDX02.DBF
BS Key Type LV Size Device Type Elapsed Time Completion Time
38 Full 6.95M DISK 00:00:03 07-NOV-11
BP Key: 38 Status: AVAILABLE Compressed: NO Tag: TAG20111107T182034
Piece Name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\AUTOBACKUP
\2011_11_07\O1_MF_S_766606834_7CH8Q439_.BKP
Control File Included: Ckp SCN: 2151141 Ckp time: 07-NOV-11
SPFILE Included: Modification time: 07-NOV-11
BS Key Size Device Type Elapsed Time Completion Time
39 18.46M DISK 00:00:05 08-NOV-11
BP Key: 39 Status: AVAILABLE Compressed: NO Tag: TAG20111108T093359
Piece Name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\BACKUPSET\
2011_11_08\O1_MF_ANNNN_TAG20111108T093359_7CJY7TG1_.BKP
List of Archived Logs in backup set 39
Thrd Seq Low SCN Low Time Next SCN Next Time
1 1 2146951 07-NOV-11 2149493 07-NOV-11
1 2 2149493 07-NOV-11 2149519 07-NOV-11
1 3 2149519 07-NOV-11 2149565 07-NOV-11
1 4 2149565 07-NOV-11 2149641 07-NOV-11
1 5 2149641 07-NOV-11 2172859 07-NOV-11
1 6 2172859 07-NOV-11 2197851 07-NOV-11
1 7 2197851 07-NOV-11 2220349 08-NOV-11
1 8 2220349 08-NOV-11 2222621 08-NOV-11
1 9 2222621 08-NOV-11 2222729 08-NOV-11
1 10 2222729 08-NOV-11 2223088 08-NOV-11
BS Key Type LV Size Device Type Elapsed Time Completion Time
40 Full 6.95M DISK 00:00:00 08-NOV-11
BP Key: 40 Status: AVAILABLE Compressed: NO Tag: TAG20111108T093411
Piece Name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\AUTOBACKUP
\2011_11_08\O1_MF_S_766661651_7CJY84LK_.BKP
Control File Included: Ckp SCN: 2223097 Ckp time: 08-NOV-11
SPFILE Included: Modification time: 08-NOV-11
Thanks in advance!
Jay

Thank you for your reply,Hemant K Chitale!
>
a) Does the directory structur exist on the new server :
D:\DBDATA\PRODDB\ --- for files 1 to 4
D:\ --- for file 5
D:\ORA_DATA\ --- for files 6 to 8
>
Yep, I have doubled check the directory structure that get in the way, and they are all exist.
Would it be something to do with the folder permissions?
>
b) Apparently a RESETLOGS has been issued on 07-Nov. Which controflile backup do you have restored and mounted on the new server ? It should be the one after the RESETLOGS.
>
I restored the one included with the backup. Should I take another backup of controlfile seperately and restore from it instead?
>
(I assume that you did a RESTORE CONTROLFILE followed by sql "alter database mount" before the attempt to RESTORE DATABASE)
>
Yep, that's exactly what I did.
//executed @ RMAN prompt of the new host
startup nomount; 'the new host has the right SPFILE to start with so i didn''t bother to RESTORE SPFILE first.
restore controlfile from autobackup;
alter database mount;
restore database sequence 10 thread 1;
//get stucked here with RMAN-06026, 06023
//...the following is not executed yet.... :-(
recover database until sequence 10;
alter database open resetlogs;Edited by: HappyJay on 2011/11/08 13:25
I have made several attemps with your advice, but still get the same type of errors.
Here is the output:
RMAN> list backup of controlfile;
List of Backup Sets
===================
BS Key Type LV Size Device Type Elapsed Time Completion Time
38 Full 6.95M DISK 00:00:03 07-NOV-11
BP Key: 38 Status: AVAILABLE Compressed: NO Tag: TAG20111107T182034
Piece Name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\AUTOBACKUP
\2011_11_07\O1_MF_S_766606834_7CH8Q439_.BKP
Control File Included: Ckp SCN: 2151141 Ckp time: 07-NOV-11
BS Key Type LV Size Device Type Elapsed Time Completion Time
40 Full 6.95M DISK 00:00:00 08-NOV-11
BP Key: 40 Status: AVAILABLE Compressed: NO Tag: TAG20111108T093411
Piece Name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\AUTOBACKUP
+\2011_11_08\O1_MF_S_766661651_7CJY84LK_.BKP+
Control File Included: Ckp SCN: 2223097 Ckp time: 08-NOV-11
as you suggested, this backup piece of controlfile should be right one to be restored.
RMAN> shutdown;
database dismounted
Oracle instance shut down
RMAN> startup nomount;
connected to target database (not started)
Oracle instance started
Total System Global Area 490733568 bytes
Fixed Size 1291360 bytes
Variable Size 364907424 bytes
Database Buffers 121634816 bytes
Redo Buffers 2899968 bytes
RMAN> restore controlfile from autobackup;
Starting restore at 08-NOV-11
allocated channel: ORA_DISK_1
channel ORA_DISK_1: sid=157 devtype=DISK
recovery area destination: C:\oracle\product\10.2.0\flash_recovery_area
database name (or database unique name) used for search: PRODDB
channel ORA_DISK_1: autobackup found in the recovery area
channel ORA_DISK_1: autobackup found: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AR
EA\PRODDB\AUTOBACKUP\2011_11_08\O1_MF_S_766661651_7CJY84LK_.BKP
channel ORA_DISK_1: control file restore from autobackup complete
output filename=D:\DBDATA\PRODDB\CONTROL01.CTL
output filename=D:\DBDATA\PRODDB\CONTROL02.CTL
output filename=D:\DBDATA\PRODDB\CONTROL03.CTL
Finished restore at 08-NOV-11
tried shutdown normally and mount again instead.
RMAN> shutdown;
Oracle instance shut down
RMAN> exit
Recovery Manager complete.
C:\>rman target /
Recovery Manager: Release 10.2.0.3.0 - Production on Tue Nov 8 13:49:42 2011
Copyright (c) 1982, 2005, Oracle. All rights reserved.
connected to target database (not started)
RMAN> startup mount;
Oracle instance started
database mounted
Total System Global Area 490733568 bytes
Fixed Size 1291360 bytes
Variable Size 369101728 bytes
Database Buffers 117440512 bytes
Redo Buffers 2899968 bytes
RMAN> restore database until sequence 10 thread 1;
Starting restore at 08-NOV-11
Starting implicit crosscheck backup at 08-NOV-11
using target database control file instead of recovery catalog
allocated channel: ORA_DISK_1
channel ORA_DISK_1: sid=156 devtype=DISK
Crosschecked 3 objects
Finished implicit crosscheck backup at 08-NOV-11
Starting implicit crosscheck copy at 08-NOV-11
using channel ORA_DISK_1
Crosschecked 2 objects
Finished implicit crosscheck copy at 08-NOV-11
searching for all files in the recovery area
cataloging files...
cataloging done
List of Cataloged Files
=======================
File Name: C:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\PRODDB\AUTOBACKUP\2011_11_
08\O1_MF_S_766661651_7CJY84LK_.BKP
using channel ORA_DISK_1
channel ORA_DISK_1: starting datafile backupset restore
channel ORA_DISK_1: specifying datafile(s) to restore from backup set
restoring datafile 00001 to D:\DBDATA\PRODDB\SYSTEM01.DBF
restoring datafile 00002 to D:\DBDATA\PRODDB\UNDOTBS01.DBF
restoring datafile 00003 to D:\DBDATA\PRODDB\SYSAUX01.DBF
restoring datafile 00004 to D:\DBDATA\PRODDB\USERS01.DBF
restoring datafile 00005 to D:\ORA_DATA\DATA01.DBF
restoring datafile 00006 to D:\ORA_DATA\DATA02.DBF
restoring datafile 00007 to D:\ORA_DATA\INDX01.DBF
restoring datafile 00008 to D:\ORA_DATA\INDX02.DBF
channel ORA_DISK_1: reading from backup piece C:\ORACLE\PRODUCT\10.2.0\FLASH_REC
OVERY_AREA\PRODDB\BACKUPSET\2011_11_07\O1_MF_NNNDF_TAG20111107T175037_7CH6YYVJ_.BK
P
failover to previous backup
//however, still get the same results(ended up with errors)
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of restore command at 11/08/2011 13:50:29
RMAN-06026: some targets not found - aborting restore
RMAN-06023: no backup or copy of datafile 4 found to restore
RMAN-06023: no backup or copy of datafile 3 found to restore
RMAN-06023: no backup or copy of datafile 2 found to restore
RMAN-06023: no backup or copy of datafile 1 found to restore
Edited by: HappyJay on 2011/11/08 13:59

Problems with WRT54G and WRT54GL

I bought a WRT54G router over a year ago and though it dropped once in a while but nothing major. I then bought a Linksys adapter for my new Dell for my room to go online and since then my router has been nothing but problems. It will run fine for a week, then out of no where it will lose signal and or connection and no matter what I do in the settings or what I reset, I can never figure out how to fix the problem. Usually after an hour it will pick up and I'll be fine again for another week. At the moment, it is not working again and has not for over an hour.
I then thought hey, I'll buy the WRT54GL as I heard many great reviews for the product. I do what the CD says, but then out of no where the cd crashes. No matter what I do, it always crashes before it can finish. The orange light never comes on and it never works at all.
I really do not know what else to do, this has become a real pain. Thanks for your time and help.

Check the firmware of the router ... if possible upgrade the firmware .... Also try to forward the ports on the router setup page ..

I just had problems with a game called call of duty 4, modern warfare. I decided that if I deleted it, I could reinstall it, I could get it back to normal. After I deleted it,I went to to the appstore and went to purchases and accidentaly deleted it/help

I just had problems with a game called call of duty 4, modern warfare. I decided that if I deleted it, I could reinstall it, I could get it back to normal. After I deleted it,I went to to the appstore and went to purchases and accidentaly deleted it. please help me!

You have not deleted it from the purchases list, it is just hidden. To unhide an app, open the Mac App Store app, click the Account link in the Quick Links to the right of the pane and go to the iTunes in the Cloud section where you can manage hidden apps.

I got problem with volume of calls...its on max and i still can hear person on other side really bad...i got 4s

i got problem with volume of calls...its on max and i still can hear person on other side really bad...i got 4s

Did you fix the problem? I have the same problem and it has been pain in the neck.

Problems with answering and making calls

I have owned a Droid 2 for almost a year now. I love it! But for the last few months I have had a problem with answering and making calls. Sometimes when I answer a phone call it connects like I have answered the call but I can't hear anything and the other person can't hear me. The call says I am connected and I can see the timer going but there is no communication. It does the same thing when I go to make calls sometimes. I can hit send and it connects the call but I can't hear anything. The timer is going and the other person answers but I can't hear anything. The only reason I know they answered is because they then call me back and leave a voicemail, sounding very confused. I have to restart my phone and then the problem is solved. But only for a little bit. I haven't been able to pick out a pattern or anything. It is random and very frustrating. I went into my local Verizon store about the issue and they arranged for me to receive a new, certified pre-owned phone because I pay insurance on my phone. I received the phone the next day and everything went great, for a few days. But this phone is also having the same problem. I am getting very frustrated with this because I need to be able to actually talk to people when they call me. Anyone else having the same problem? I want to go back to the store but I feel like they wouldn't do anything more than they did last time, which didn't solve the problem.

I have this same issue on a bi-daily basis: I can place a call, but then I hear nothing. I can answer a call, but I then hear nothing. The calls connect as the people I am in contact with will tell me they answered my calls and heard me, though I could not hear them - and vice versa. Also, this phone does not like to place a call using the "call" option if dialing from "recent calls". I turn this phone on/ off daily, I've taken the battery out on about 50% of the occassions when this issue has happened. This has been a problem for me for approximately 1yr. My early renew date is just shy of 2 months from now and I cannot wait to get rid of this phone. Aside from having great difficulty making/ receiving calls, the phone is overall slow to respond to basic functions like text messaging or using the camera. Also, most times while taking a picture, the camera will "take a picture" but then there is no image in the file. Highly annoying - the only way to temporarily fix this is to reboot - but like the call issue, the problem recurs. I do have a bunch of apps on installed on the phone, but since I also have an APP killer on the phone, nothing aside from "Weather Bug" app is ever really running in the background that would slow this phone. BUT, right now my main concern is may safety: God forbid I am ever in danger or in an emergency situation, this phone's constant malfunctioning could possibly be the physical harm or death of me. I hope that my family can sue the company that provides the software for this phone, Verizon & Motorola in the event of my untimely death.

Tp ended with error code 0247 - addtobuffer has problems with data- and/or

Hello Experts,
If you give some idea, it will be greatly appreciated.
This transported issue started coming after power outage, sap system went hard shutdown.
Then we brought up the system. Before that , we do not have this transport issue.
our TMS landscape is
DEV QA-PRD
SED-SEQSEP
DEV is having the TMS domain controller.
FYI:
*At OS level, when we do scp command using root user, it is fine for any TR.
In STMS, while adding TR in SEQ(QA system), we are getting error like this.
Error:
Transport control program tp ended with error code 0247
     Message no. XT200
Diagnosis
     An error occurred when executing a tp command.
       Command:        ADDTOBUFFER SEDK906339 SEQ client010 pf=/us
       Return code:    0247
       Error text:     addtobuffer has problems with data- and/or
       Request:        SEDK906339
System Response
     The function terminates.
Procedure
     Correct the error and execute the command again if necessary.
This is tp version 372.04.71 (release 700, unicode enabled)
Addtobuffer failed for SEDK906339.
Neither datafile nor cofile exist (cofile may also be corrupted).
standard output from tp and from tools called by tp:
tp returncode summary:
TOOLS: Highest return code of single steps was: 0
ERRORS: Highest tp internal error was: 0247

when we do scp using sm69,
SEDADM@DEVSYS:/usr/sap/trans/cofiles/K906339.SED SEQADM@QASYS:/usr/sap/trans/cofiles/.
it throws the error like below,
Host key verification failed.
                                                                                External program terminated with exit code 1
Thanks
Praba

Problems with WRT54G and Call of Duty 4 hosts....XBOX360

Similar Messages

Maybe you are looking for