Production client in modifiable stage even after client is closed.

Dear All,
I observed in my system that production client settings of spro is modifiable even after the client is closed.Can you suggest where the problem would be.Where as with same settings (of even customising client closed I m not able to modify in DEV).
Please suggest.
Regards,
Amit

Hi,
Cross Client and Customizing Settings should not be allowed and No Changes allowed.
At same time check in Se06, system status should be non-modifiable.
Thanks
Sunny

Similar Messages

Installed latest iOS on my iPad mini, it got stuck while restarting after update. It is still in that stage even after 7 hours.

installed latest iOS on my iPad mini, it got stuck while restarting after update. It is still in that stage even after 7 hours.

Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
   1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
       other end of the cable connected to your computer's USB port.
   2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
       until the red slider appears, then slide the slider. Wait for the device to turn off.
              * If you cannot turn off the device using the slider, press and hold the
                Sleep/Wake and Home buttons at the same time. When the device turns off,
                release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
       device. The device should turn on. Note: If you see the battery charge warning,
       let the device charge for at least ten minutes to ensure that the battery has some
       charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
       When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

In OAM, is it possible to maintain a cookie even after browser is closed?

I've a requirement where I would like to maintain a cookie on a portal (after the user is authenticated) even after the user closes the browser (without logging off)? It is something like on ebay or Yahoo where you've option of remember me so that when user visits the website, they need not login unless logged out?
Any inputs would be really appreciated. Thanks.

No not by default. There are multiple options to make it work though...( My 2 cents is to look at security risk before deploying this type of solution)
a) If your users are Windows / part of AD, you can enable Integrated Authentication (Intranet users)
b) You can capture the userid and password before you post to OAM and encrypt and store it in your cookie. next time user comes to your site you then look at the cookie and try to sign in as that user. ( Security Risk...to be considered based on type of application or data user has access to)
Ram

Production Order is Still saved even after CK 465 message changed to Error

Hi,
While creating production order in CO01,we are getting one Warning message CK465.I have made that warning message CK 465 as Error Message in configuration.
After that i have created on Production Order in CO01.When i see the Log in CO01,it is showing as Error Message.But the production order is getting saved.
As per the client requirement,when we get that CK 465 -Costing Error,The production order should not be saved,but in my case it is gettings saved,Now what should i do?
The Error Message is:
No price could be determined for material/batch 0118E9152/ plant AX01 @35\QLong text exists@Costing
Kindly advice me how to prevent this production order saved when it is error mode.
Thanks
Supriya

Just a question: Do your Clients have a process to correct the error in production order costing without seeing the Order BOM and Routing? I can think of many examples here that you wouldn't be able to fix without seeing the order. Our acounting dept uses COOIS to review orders with status CSER.

The Firefox.exe process hogs 25% of my CPU resources even after I've closed it.

On a relatively consistent basis, when I close the Firefox windows I have open, the firefox.exe process doesn't end. When I go to open Firefox again later, I get the error message that I can't open Firefox because it's already running or not responding. When I look in Task Manager (on Windows 7 Home Premium 64-bit, BTW), the firefox.exe process is holding steady at 25% CPU usage along with whatever memory usage it already had consumed, even though the Tasks tab doesn't list Firefox as being open.
== This happened ==
A few times a week
== I'm not exactly sure. It sort of just started on its own.

Ed, this kind of issues are, unfortunately, more common and the we'd like. Thankfully, 99% of the cases are very easy to solve. However, you do need to diagnose what your exact problem is. Do this:
#run Firefox in [http://support.mozilla.com/en-US/kb/Safe+Mode safe-mode] to disable all extensions, themes and plugins. If this fixes your issues, be them with RAM or CPU usage, then you know it's a problem with plugins, themes or extensions. Proceed to number 2. If safe-mode doesn't fix the issues, then read bellow, after this list;
#update all extensions, themes and plugins in your Firefox. If this doesn't solve the issues, proceed to the following number;
#disable all extensions, themes and plugins in your Firefox (not running safe-mode). Being certain that, as in safe-mode, the problems you're having have gone away, enable one plugin at a time. You should be certain that you WANT that plugin to be enabled, so keep your overall number of plugins as low as possible. When you encounter the problems, you know you've found a problematic plugin, so disable it for good. Keep enabling all plugins (except problematic ones) until you've gone through them all.
#enable one extension at a time. Again, be certain that you WANT that extension to be enabled, so keep your overall number of extensions as low as possible. Also, try the theme you want to have installed so see if that is what's causing the problem. When you encounter the problems, you know you've found a problematic extension/theme, so disable it for good. Keep enabling all your extensions (except problematic ones) until you've gone through them all;
#you're done! You've fixed your problems with problematic add-ons. If you want to keep using those problematic add-ons, please contant their author for support.
Ok, if disabling all extensions and plugins through safe-mode didn't work to bring Firefox's CPU and RAM usage to good levels, then you have different issue. The most likely scenario is that you have a third party software running on your computer that is messing with Firefox. Do as follows:
#try reinstalling Firefox. No data will be lost. You can get the latest version for free at [http://www.getfirefox.com/ getfirefox.com]. If that doesn't fix the problem, proceed;
#do a virus/malware check on your computer. If this doesn't fix it, proceed;
#disable all software running in the background that you don't want to have running in the background (in windows, this is done by pressing WINDOWS+R in your keyboard, typing "msconfig" (without the commas) and pressing enter. Now, under the "Startup" tab, you can uncheck the software you don't want, and reboot your system for changes to take effect. If you're unsure of what software you want running, ask someone with more experience). If this doesn't fix your issues with Firefox, proceed;
#check your firewall/antivirus/security suite for enabled functions/features that you don't want and/or may be conflicting with Firefox. You'll find that these features are most likely tied to Internet Security features, such as link scanners or URL checkers and the like. If you're not sure they are conflicting with Firefox, simply try to disable them to see whether or not that's true. As long as you don't browse the web with your antivirus completely off and your firewall completely turned off, there should be no problems. If this doesn't solve the issues, proceed to the following number;
#check your operating system security options, mainly advanced options that are not configured by default. While it's very unlikely that this may be the cause of the problem (after all, it's the last item on the list), it's remotely possible. If this doesn't work, proceed to the following point;
#update your modem/router software. There have been some reports that some modem/router software may cause Firefox and other browsers to loose performance and/or stability. If updating doesn't fix your issue, try other versions of the software, if possible. If you need support with this, contact your modem/router manufacturer. If this doesn't help, proceed;
#clean up your OS registry, using appropriate software. Make sure you've followed my instructions correctly, but if this all doesn't work, [http://support.mozilla.com/en-US/kb/Managing+profiles create a new Firefox profile] (this can be temporary, of course) and see if the issues persist. Report here the results, so we can help you further.

New Ipad continues to draw down battery even after cover is closed. Is this normal?

Even though I close the cover and can hear the magnetic switch shut off the Ipad, it continues to draw down my battery, is this normal?
Screen does go blank

I've read different opinions (and personal stories) about whether the battery drains in sleep mode. All I know is that mine does not seem to drain. I was just noticing this last night. Before I went to bed my battery meter read 97%. I simply closed the smart cover to put it in sleep mode (I heard the click). When I opened the cover this morning it was still at 97%. I used it for about 15 minutes and only then did it drop to 96%. I did not turn off any wifi or location settings.
I should disclose that my battery meter was acting weird the other day. After a full charge, it was stuck on 100% during a few hours of light use (internet, email, kindle) before dropping again. Maybe my meter is just screwed up, but it seemed to be back to normal again and draining at a normal rate prior to my observation about it not draining at all during sleep mode.

Firefox doesn't open a link van I click on a link is thunderbird, its say that firefox is active but doesn't respond, sometimes even after it has closed

When I got in an email a link and I click on it, firefox openes the first time, but when I click on the next link I get the message that firefox is active but doesn't respond.
Opening by clicking on *.htm(l) files works fine even multiple.

I suggest you to upgrade your browser to Firefox 7 and check:
* getfirefox.com

Can we remain in the same state even after clicking submit button?

Hello All,
Can we remain in the same stage even after clicking submit button? Also it should remain in the same stage only when certain conditions are met. For eg:
Condition : In Stage1, CustomFieldA default value is 'No'. To pass from Stage1 to Stage2 the CustomFieldA value should be made to yes.
Scenario 1 : CustomFieldA value is 'No', and I click on Submit .
Expected Result : should remain in the same stage
Is above result achievable in PS 2013? I am creating workflow in Visual Studio 2012, so can I handle this in the workflow?
Please help.

The above answer was proved wrong, so please follow this link to get the answer.
http://social.msdn.microsoft.com/Forums/en-US/8c75d74d-1ea6-4273-96cd-e70f5a5688fc/how-to-remain-in-the-same-stage-even-after-clicking-submit-button?forum=project2010custprog

Installed 3.6.6 and found PLUGIN-CONTAINER.EXE-15EDC9DD.pf running in task manager allowing voices/music from some unknown web site to continually play even though firefox is closed. 3.6.6 is a major problem and also continually crashes! in English

After downloading 3.6.6, plugin-container.exe allows an unknown website to continually stream audio through my speakers, even after firefox is closed. I kill the process in task manager and it still relaunches itself. I found this file also running by search my computer PLUGIN-CONTAINER.EXE-15EDC9DD.pf in c:\Windows\Prefetch. When I kill that process, audio instantly stops. But it relaunches after 10 minutes or so. The process eats up lots of memory. I've had to restart firefox in safe mode several times as it crashed even before opening. 3.6.6 is majorly flawed and I'm running Windows XP. Time to downgrade to 3.6.4
== This happened ==
Every time Firefox opened
== I downloaded 3.6.6

After downloading 3.6.6, plugin-container.exe allows an unknown website to continually stream audio through my speakers, even after firefox is closed. I kill the process in task manager and it still relaunches itself. I found this file also running by search my computer PLUGIN-CONTAINER.EXE-15EDC9DD.pf in c:\Windows\Prefetch. When I kill that process, audio instantly stops. But it relaunches after 10 minutes or so. The process eats up lots of memory. I've had to restart firefox in safe mode several times as it crashed even before opening. 3.6.6 is majorly flawed and I'm running Windows XP. Time to downgrade to 3.6.4
== This happened ==
Every time Firefox opened
== I downloaded 3.6.6

Production Client 700 not modifiable

Guys,
I need to upload trial balances in my production client thru LSMW.and in testing in QA, I got the error msg. for tax line items exceeding 999 and I had to turn off the taxware which dteremines the taxlineitems line by line.So I was able to upload trial balances in QA after that.Now I need to upload in production and in production client is set to "Not Modifiable".I just need to turn off taxware only, and afterwards I will put production client back to the previous status.Anyone please suggest me how to do it in production.Thanks
Regrads
Shaun

Hi,
You can switch off the flag in SCC4 transaction or via maintainance of T000 table. But, you'd better coordinate it with your BASIS/ABAP team, because normally it should be allowed only with their permission.
Regards,
Eli

I am trying to access a webpage but it keeps saying I need a client certificate. Even after I click 'continue', I still cannot access the webpage.

I am trying to access a webpage but it keeps saying I need a client certificate. Even after I click 'continue', I still cannot access the webpage.

https://etivity.sul.com.au/
It's to access my work rosters.

Trying to update adobe flash, keep getting 'quit dashboard client'. Everytime I try to, it pops back up. Even after going to activity monitor and force quitting. What is it and how can I quit it so I can install this update??

Trying to update adobe flash, keep getting 'quit dashboard client'. Everytime I try to, it pops back up. Even after going to activity monitor and force quitting. What is it and how can I quit it so I can install this update??

Restart the computer from Apple menu.
When restart dialog box appears, uncheck the box beside
"Reopen windows when logging back in".

Adding new project mask in Production Client

Hi,
I have requirement of adding new project mask code for Production client.
As SAP standard functionality does not allow you to add any new project
mask once you create a project .So if I try to add new mask system will not
show me projects already created and released.Is there any solution to this
problem?
Ranjit

Hi Ranjit,
You did not specify exactly what type of new mask you are adding. For example, maybe you simply need to modify an existing code. You can make two changes to existing codes that have projects created.
1. You can extend the length of the mask to the complete 24 characters, if not already 24 characters.
2. You can change any 0 (numeric only) character in the mask to an X (allows alphanumeric).
The best means to see what project codes are already in use, you should run SE16 for table PROJ and PRPS. You want to view the fields in PROJ-PSPNR and/or PROJ-PSPID as well as PRPS-PSPNR and PRPS-POSID. So, any project code beginning values (A, B, C, etc; 1, 2, 3, etc) displayed cannot be setup as new project codes.
Yes, you could delete the old project codes after archiving the structures, but you also have to (or should) archive any associated financial documents. As the previous responder stated, this is not a trivial task.
Points appreciated....
Regards,
Kent Bettisworth

Assign a Logical System Name of a production client

Hi everybody,
We have an ERP system (now upgraded to ECC 6.0) that is in productive use since 7 years. Until now, no Logical System Name have been assigned to the production client - the field in transaction SCC4 is empty/blank.
Now we plan to implement a BW, so a test and a productive BW systems have been installed. According to the attached file and content of note 184447 we choose to use "Option 1: Uniform Logical System names clients by system type" for naming convention for LSN's.
All the systems/clients (BW test and productive, ERP test only) now are assigned with corresponding LSN's, except the production ERP client. It is still without LSN and the client is not defined as Source System for productive BW system.
So, my question is:
Should I expect any problems if the LSN of the production client is set up now, after long time, effective productive use?
I would mention that this is infact initial setup, not a change of LSN. Therefore transaction BDLS is not relevant, I think.
Thanks in advance

Hi DB49,
I already did an initial setup of LSN in the test ERP client (that client is copy of the productive ERP client, i.e. the LSN has not been set). And everything seems to be OK.
But the documentation says that ".... In a production system, the logical system must not be changed ...".
"Changed" is not "ïnitial setup" of course, so there will not be any problems I hope, but ...
SCC4 --> LSN field --> F1 -->
"System in which applications run integrated on a shared data basis.
The distribution of data between systems requires that each system in the network has a unique identification. The logical system is used for this purpose.
In the SAP System the client corresponds to a logical system. You can assign a logical system to a client in the client maintenance (choose Goto -> Detail).
The logical system is relevant in the following SAP areas:
ALE general: two or more logical systems communicate with one another.
ALE - ALE business processes (for example, cost center accounting): definition of a system where a specific application runs. Changes to master data can only be made in this system, for example.
Workflow objects: the logical system in which the object is located is always included in an object's key.
When maintaining the logical system, note the following:
The logical system must be unique company-wide. It must not be used by any other system in the ALE integrated group. In a production system, the logical system must not be changed. If the logical system of a document reference is not set to initial and does not match your own, the system assumes the document is located in a different system."

Profile for Production Client in production server.

Dear Tech Masters,
I have installed SAP ECC 6.0 (Production server). Now I want to create client ( First client after installation), which would be the production client. I am not sure about the profile for client copy from 000. After a lot googling ...I am confuse whether SAP_ALL or SAP_CUST which one I use for client copy from 000 for production client.
Please help me asap.
Edited by: RABI PAL on Jan 2, 2009 7:44 PM

go with SAP_ALL
you are using 000 client and ur going to create new client XXX for XXX client you try to use SAP_ALL then you can you DDIC with full authorizations for XXX Client.

Production client in modifiable stage even after client is closed.

Similar Messages

Maybe you are looking for