Profibus and IFM-controller

We have a new fermenter with profibus port.
it's has an USB-RS485 converter(PC) cable.
I want to edit a subvi in labview 2012.
where can I find the driver or examples?

The profibus protocol uses the rs485 bus but a protocol that is quite complex and best can be supported by special hardware.
So don't try to save some bucks and generate a slow sometimes working protocol that costs a lot of time.
greetings from the Netherlands

Similar Messages

Problem with NEO2 and sata controller card

1.Product Type: MSI K8N Neo2 Platinum (MS-7025)
and the controller card is a InnoVision DM-8301 and the hard drive is a Seagate ST3320620AS
2.BIOS version: The newest one, 1C0 or something.
3.External VGA Type: Geforce 6800 GT
4.CPU Type: AMD 64 3500+
5.Memory Type: G Skill ZX 2048mb.
6.Power Supply Type:
7.Operating System: Xp Pro
8.Problem Description:
Hello. I have a strange problem with my controllercard. I wrote this text to InnoVision suport and they send me files and bios updates for a whole week and it was still the same problem. And then i tried the card in an older computer and everything worked fine.
I wrote
"Hello. I got some problems with my new controller card. I can find my new harddrive ,that's conected to the controller card, when iam inside windows and it's seems to be no problem. I can look on every seting on it and everywhere i look i can read "No problem". I Also did some test with the seatools programe and everything was fine. But when i schould copy files to it the coumputer start lagging after a few seconds and i cant do anything. After a while i can move the mouse around but the it laggs again. My computer is overclocked at the time but i have tried to use the harddrive when it's not clocked also. Also when im goin in to teh controlpanel and starts the setings for Sillicon Images sata controll and have music on my computer, the music laggs for a very very short moment. Something must be wrong and i can not find it."
It's still the same problem in my computer. The older computer had a MSI moderboard with a VIA chip and i have a nForce 3. InnoVison said i should talk to you about this problem. I have 3 harddrives but i use this controllercard because i want to have my computer overclocked and then i can't use 2 of the sata ports as i think you know.
I would be very thankful if you could help me with this problem.
//Martin

I've used a noname SATA pci card (non raid) with SIL3112 on my neo2 without problems with 1C bios.
Think you may try with a disk lower than 48bitLBA need (137GB barrier), eg a 120GB disk
Quote:
have the InnoVision EIO DM-8301 and had alot of problems using it with WD 160MB SATA drive.
I am using Intel 865 based MB with 2 original SATA channels. The original SATA channels are bootable.
I could not used the EIO card with 160G HDD. The whole setup is working only after I connected oine of my 120G Segate SATA HDD to the EIO Sata card.
I think this card do not properly support HDD above 120G.
Please respond to: [email protected]
http://www.devhardware.com/forums/storage-devices-80/sata-as-boot-20080-2.html
Btw: you have xp sp2 ?
48bitLBA is not enabled in the first version.
http://www.48bitlba.com/winxp.htm
Edit:
Here's another with complete different setup and same problems
http://forum.tweakxp.com/forum/Topic212148-4-1.aspx
I doubt it has anything to do with your motherboard and/or bios.
Btw: I looked at innovision and their drivers in download area are very old.
Get the latest SIL3112 drivers for XP here:
http://www.siliconimage.com/support/supportsearchresults.aspx?pid=63&cid=3&ctid=2&osid=4&
And remember 3112 is sata150 only , so it's not sure it will work with your drive at all .
Anyway it should be set to fixed sata1.5G with jumper - not certain the controller can autonegotiate
without trouble. You cannot have command queing enabled either , disk support only NCQ and controller TCQ
so having command queing set ON will cause major conflicts in data transfers.

Inventory report for the selection of requisitioner and MRP controller

Hello Experts,
Can someone please help me with a standard Inventory report in which we can give input thr requistioner and MRP controller
regards,
YK

Hi,
You will get the requisition no. from EKKO (provided PO has been created otherwise you won't get any record). Find out PO & item no. for the requisition item. Then you can check EKBE table whether GR has been posted or not. If GR has not been posted then there won't be entry in EKBE for that PO & item.
Regards,
Rakesh

Communication between : AP and WLAN controller

Hi,
The communication between AP and WLAN Controller is ( Data and Control ) UDP.
Source port 1024 and destination port 12222 and 12223. Actually which device listen to which port or both should listen as control and data can be generated from both the devices.
How does the user ( wireless client) traffic is switched - if user traffic is a TCP traffic. It will be sent to WLANC and then WLANC forwards it to respective VLAN or default gateway ( depending upon the destination in the packet ).
Please explain / share the experience.
any link on cisco.com
Thanka in advance
Subodh

"the LWAPP Control and Data messages are encapsulated in UDP packets that are carried over the IP network. The only requirement is established IP connectivity between the access points and the WLC. The LWAPP tunnel uses the access point's IP address and the WLC's AP Manager interface IP address as endpoints. The AP Manager interface is explained in further detail in the
implementation section. On the access point side, both LWAPP Control and Data messages use an ephemeral port that is derived from a hash of the access point MAC address as the UDP port. On the WLC side, LWAPP Data messages always use UDP port 12222. On the WLC side, LWAPP Control messages always use UDP port 12223.
The mechanics and sequencing of Layer 3 LWAPP are similar to Layer 2 LWAPP except that the packets are carried in UDP packets instead of being encapsulated in Ethernet frames."
Taken from "Cisco 440X Series Wireless LAN Controllers Deployment Guide"

Win 8.1 domain workstation. Block all access, except for a fews users/groups and domain controller information/date.

Hi!
Win 8.1 pro, domain workstation. How Block all access, except for a fews users/groups and domain controller information/date.
Nuance:
From domain AD is locked Workstation Firewall "Domain profile" edit.
Possible?
cenubit

Hi GirtsR,
I am not sure the command to use the SID to accomplish what you want to achieve, if you only know the SID, you could take use Powershell to find the related information, more information, please check:
Working with SIDs
And a similar thread for reference:
How to find user/group known only SID
More reference: Default local groups.
Best regards
Michael Shao
TechNet Community Support

Diff between Component controller,Custome controller and View controller

hi,
Can any body tell me the following details,
1.difference between the Component controller,Custome controller and View controller in WD-ABAP.?
2.what is Lead Selection?
Regards,
Ravi

Hi Ravi.
The component controller is visbile to all views in a component. So all context nodes and methods you create here can be accessed from all views in the component. This way you can share data between the views by mapping context nodes or thru method calls. You can also mark methods and nodes as interface so that they are acessable from other components that define component usages to this cmponent.
Custom controller is quiet similar to the component controller. You can define it if you want to group some views with a custom controller for a certain functionality.
If you want to access a custom controller in a view you have to define the usage first on the properties tab of the view.
A view controller is only visible in the view itself. So all methods or context nodes you define here are only accesable by the current view.
The lead selection is in most cases the current selected element in a context node. The lead selection is used by many UI elements to determine which element has to be shown (e.g drop down).
If you have a table with single selection the current selected table row is the lead selection element of the bound context node.
SO you can get the lead selection element easily in any mthod by calling context_node->get_element( ).
Hope this clears your questions.
Cheers,
Sascha

Difference between AP Operational Status and Registered Controller

When reviewing the AP Details page in Prime there are two fields I'm not sure what they mean specifically:
1) Operational Status - Registered
2) Registered Controller - Not Associated
Any clarity or document references would be greatly appreciated.

This is in CPI viewing the AP Details tab.
The only valid values for Operational Status are Registered/Not Registered.
The only valid values for Registered Controller are Associated/Not Associated
The IP address is not a valid input.
It is still unclear to me what the specific and fuctional differences and impacts are between Operational Status and
Registered Controller? How do the values of each impact the client device?
Thank You.

I have got a 1500 Kinetic Systems CAMAC crate and 3922 controller. I want to use it with LabView inst

alled in PCI-bus IBM PC, which does not have GPIB interface. Which way would be easier for developing my own instrument driver: a new GPIB controller + interface or 2915 Kinetic Sys. PCI-bus in-slot interface? Can the latter interface be used with LabView?
Many thanks.
Victor. I have got a 1500 Kinetic Systems CAMAC crate and 3932 controller. I want to use it with LabView installed in PCI-bus IBM PC, which does not have GPIB interface. Which way would be easier for developing my own instrument driver: a new GPIB controller + interface or 2915 Kinetic Sys. PCI-bus in-slot interface? Thanks

alled in PCI-bus IBM PC, which does not have GPIB interface. Which way would be easier for developing my own instrument driver: a new GPIB controller + interface or 2915 Kinetic Sys. PCI-bus in-slot interface? Can the latter interface be used with LabView?Victor,
I couldn't find an Instrument Driver for the 3932 crate controler. There is a driver for the 3988: http://zone.ni.com/idnet97.nsf/9b2b33e1993d877786256436006ec498/045f8392cc4d1b01862568ab005fbb49?OpenDocument
If you look at the driver it isn't too complex. Well ... actaully there are certain differences when using the 3988 GPIB controller that the driver takes care of that relate to correctly passing commands (FAN).
If the 3922 controller is similar then maybe you can use the 3988 driver and modify it to meet your needs. I'm not familar with the 2915 Kinetic system so I'm not sure what would be easier.
If you have a GPIB board, then you could try using the 3988 driver with your 3922 controller and see if you can modify the driver to get things to work.
I
've only used the 3988 and that was quite three years ago but it might be worth a try.
Best of luck,
Kamran - NI

Unable to install lan realtek rtl8101 and network controller driver on windows server 2008

Hi Guys,
i am trying to install realtek rtl 8101 f amily driver and network controller driver on windows server 2008 but unable to install.
Hp device Model.:- hp pavilion g4 1303au
Model no.:- 5c03213jsh
network controller Device ID: PCI\VEN_168C&DEV_0032&SUBSYS_1785103C&REV_01\4&211965BF&0&0020
Name: PCI Device
Device ID: PCI\VEN_10EC&DEV_5209&SUBSYS_3564103C&REV_01\4&34BC5A71&0&0030
Name: SM Bus Controller
Device ID: PCI\VEN_1022&DEV_780B&SUBSYS_3564103C&REV_13\3&2411E6FE&0&A0
thanks,
Amit Rai

Hi:
SMBus controller:
Here is what I have done...I have zipped up and attached below under Attachments, the raw smbus controller driver files for you to unzip and manually install.
Download and unzip the file.
Go to the device manager and click on the smbus controller needing drivers. Click on the driver tab. Click on Update Driver.
Select the Browse my computer for driver software option and browse to the driver folder that you unzipped.
Make sure the Include Subfolders box is checked and the driver should install. Then reboot.
Ethernet: Download and install the 1st driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=7&Level=5&Conn=4&DownTy...
Card reader (PCI dev.): Download and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=15&PFid=25&Level=4&Conn=3&DownT...
Wireless: You will have to try the Vista driver for the Atheros wireless card...
http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5060882&sp...
Attachments:
sp66185.zip ‏7 KB

PCI Device and Network Controller uninstalled

Having problems with downloading a pci device and network controller driver for presario cq57? Need help. my hardware id is PCI\VEN_10EC&DEV_5209&SUBSYS_3577103C&REV_01

Hi:
You need to install the Realtek Card Reader driver from your notebook's support and driver page for the PCI device.
Please do the following so I can find out what model wireless card your model uses...
Go to the device manager, find the Other Devices category, and click on the Network Controller needing drivers.
Then click on the Details tab at the top of the network controller window.
Now you see a Property drop down list and it is defaulted to Device Description.
Drop down on that and select the second item on the list (Hardware ID's).
Post the top string of characters that begin with PCI\VEN.

Profibus and OPC questions

Hi,
I need to communicate from Labview to a Siemens S7 PLC via Profibus and I have a few questions.
1. Does anyone have any recommendation on using the Siemens Prifibus PCI card/OPC server or Applicom PCI card/OPC server or other make?
2. What is the best way to communicate from Labview? To an OPC server by datasocket(I seem to see a lot of comments about Labview not being a very good OPC Client when using datasocket!), or to an OPC server by ActiveX automation, or by ActiveX controls?
Any help is appreciated!!
Sal

Hi,
1. I have had customers using Applicom cards and OPC Servers without much problem.. overall, they're pretty good.
2. For OPC in LabVIEW, LabVIEW Datalogging & Supervisory Control (LVDSC) module is the way to go! LVDSC is an add-on module which you can install on top of your LabVIEW. It provides native (non-datasocket) OPC support. In addition, it also provides features typically required by a datlogging and supervisory control application, like historical logging and trending, alarming, security, etc. Check it out:
http://sine.ni.com/apps/we/nioc.vp?cid=10418〈=US
Hope this helps.
Rgds,
Khalid

T42 Ethernet and Network controller problems

I am fairly new to computers and obtained a T42 for my grandson. Please bear with me as I am rather Techno challenged and battled now for 2 days getting internet connection. Had to do a clean XP SP2 installation and landed up with a host of Other devices issues with Yellow Question marks. Have downloaded most drivers from http://support.lenovo.com/en_US/downloads with various success. Need serious help here please.
In Device manager I am sitting with two unresolved issues under Other Devices
Ethernet Controller PCI\VEN_14E4&DEV_167D&SUBSYS_05771014&REV11\4&111A1FD8&0&00E0
AND
Network Controller PCI\VEN_8086&DEV_4224&SUSYS_1011808&REV_05\4&AD1B67F&0&10F0
I have downloaded various drivers but still cannot get them to work. Not sure which of the drivers to use.
In another forum somebody replied
The Intel PRO/1000 is an ethernet controller. Once you get that installed and establish a network connection, you can download and install MS dotnetfx and Lenovo System Update which will download and install all the other drivers automatically. Or just download them yourself and manually install them.
Not very helpful as I could not figure ou thow to install as the drivers that I downloaded did not fix this and no further help from them when I questioned this
Please if someone here will give us some step by step directions. The model is 2373-L77 if that will help
Solved!
Go to Solution.

raycomp schrieb:.
Ethernet Controller PCI\VEN_14E4&DEV_167D&SUBSYS_05771014&REV11\4&111A1FD8&0&00E0
AND
Network Controller PCI\VEN_8086&DEV_4224&SUSYS_1011808&REV_05\4&AD1B67F&0&10F0
I have downloaded various drivers but still cannot get them to work. Not sure which of the drivers to use.
Checked the "DEV_" # on www.pcidatabase.com
upper: Broadcom NetXtreme Gigabit Ethernet driver (it seems, you have a T43-System Board in your T42 or you have a T43).
lower: 802.11a/b/g WLan adapter driver (Intel 2915 Wireless LAN adapter)
Please find the installation instructions on the linked pages. Executing the downloaded packages extracts them only to C:\DRIVERS\WIN\xxx.
Starting there you'll need to execute the setup as described on the download page.
My home-forum: http://www.thinkpad-forum.de
Wiki: Deutsches ThinkPad-Wiki English ThinkWiki
My ThinkPad-Collection

PCI devices and network controller

Hi there can anybody tell on hoe to install the PCI device driver and the network controller please as these two devices is marked with an ? in the devices managers windows
Thanks

Subject: Re: PCI devices and network controller (Satellite SM 30 X-165)
Good morning
I have a problem i bougt a laptop in china but to translate it thay reprogramed everything and my modem was desinstaled, i dont exactly know which model it is, its a toshiba satellite and the mothem comes whit a ? (yellow question marc) and the name it apears is modem PCI
could you help me
Message was edited by: andres_pedroza

Change prim and sec Controller IP from WISM or Prime

Hi all,
we have a Cisco Prime 2.2.0 and a redundant (SSO) WISM2 pair (8.0.110.0) and about 700 APs.
After conversion to redundancy of WISMs and because of different local configurations of some APs we have to change the IP
of the primary and secondary controller of nearly all 700 APs.
Is it possible to change the addresses of all APs from the WISM or Prime web interface ?
It would be very hard to configure each AP individually.
Thank you.

Hello to all,
Did you find at the end what was the cause which generate the problem and the messages???
The WLC or something on the network and hte messages were the consequence???
Many Thanks for a feedback
Omar

View and View controller in WebDynpro component.

Dear SDN Community,
I don't see anything like View controller in the webdynpro component. In the WebDynpro component I see only View but no View Controller. Is it that in the webdynpro component view and view controller are physically same and when you swtich to the layout tab its the view and the rest of the tabs for the View controller. May be a stupid question but I would appreciate your clarification here.
Thanks!
Surya

Yes, they are to some degree merged in the IDE. For example, there is only one Java source file for view and view controller. The metadata on the other side are stored in different XML files.
Armin

Profibus and IFM-controller

Similar Messages

Maybe you are looking for