Program sky remote to TV

Please can someone help me. I've tried everything to program my remote to my TV and it's not doing anything. I have the right code but still nothing. Thanks in advance

I assume you're using a bona fide Sky remote.  Some cheap clones do not have tv macro's stored and cannot be programmed, they can only operate the digibox.  If the remote does not flash twice after selecting 'Select&Red' together,  you won't be able to use the remote for controlling the tv. If you have a genuine Sky remote,  reset it to its factory status.  Press: TvSelect & Red together  ( remote LED flashes twice )999                                        (                   -"-                               ) then try entering the tv code as you have done already.   

Similar Messages

  • Programming sky remote to control new TV

    We've just bought a new TV so have tried to programme the Sky remote to control the TV volume but to no availAll instructions have been followed -Sky remote is a Rev9TV is a Panasonic TX40C 300B Codes tried are: 166406782505167802540051 It has worked to control everything BUT the volume! We've tried resetting it by taking batteries out, holding select button for 30 secs etc but it still won't control the volume there any other codes to try? Any suggestions gratefully received! Thanks :-)

    I emailed Panasonic reguarding a code and this is the reply I got - Dear Mr. Jones,Thank you for your reply.In response, I am writing to inform you that at the moment we are not aware of any such codes and we cannot provide you with a guarantee that this will become available at some point.I appreciate that this answer might be disappointing and I am sorry that Panasonic cannot be of assistance in this particular case. Should you have any further queries, please do not hesitate to contact us again and we will endeavour to further assist.Kind Regards,
    George Customer Service Team
    Panasonic UK   Have to say its not looking good

  • LED TV 40TL963 restarts when using Sky remote!!

    Hello guys, My 40TL963 LED tv has started to shut down and restart when we use the Sky remote. No matter which direct we point it!!!
    Its never done it before. I have had this telly for over 2 years now and this has only just started to happen.
    Any advise would be greatfull.
    Thanks

    Did you try with a RESET of the TV set already ? (if you don't wanna loose your channels you should use the "ToshibaEdit" tool to avoid useless work for sorting afterwards, before you are doing this).

  • Using windows program with remote access.

    I have to work with a complex electronic medical records program (Allscripts) remotely from home on my Mac. The program is not really Mac friendly. It has to run on Java at home and it requires "right click, left click" operations on the pc that I can't figure out how to make work on the Mac. Any suggestions on how this may be able to work?

    Any suggestions on how this may be able to work?'
    Get a 2 button mouse

  • Sony HT-CT60BT Soundbar and Sky Remote

    Hi there I know I can give the codes a go to check, but I am yet to order the Sony HT-CT60BT Soundbar and wondered if anyone had got their sky remote to control the volume on this specific soundbar before I do? Thanks in advance

    I wish!  I have tried everywhere to get these codes, without success.  It's a fantastic soundbar, but changing the volume is such a faf.  

  • Remote Code for Sky Remote rev 9 to Yamaha rx-v363 surround amp

    Hi, I've just replaced my old Sky remote as the '0' stopped working. The old remote worked absolutely fine with my Yamaha amp. I've tried all the Yamaha codes suggested (0171, 0876, 0382, 0204, 1304, 0740, 1359, 0214, 1843, 2049, 2089, 2144, 2370 and 2365) but to no avail. The code I've been using on the old remote was given to me through this forum around 3 years ago but I cannot find the original thread.  Does anyone have any additional code suggestions or know if it's possible to obtain the code from my old remote? I've done this previously with another remote by counting the number of LED flashes, however, I've been unable to find anything that would suggest this is possible via a Sky remote. Thanks 

    Try  http://helpforum.sky.com/t5/Archived-Discussions/setting-sky-remote-to-operate-av-receiver/m-p/830248#M5209  

  • Sky Remote Code for JMB 42883

    Looking for a sky remote code for my LCD JMB 42883, tried all the codes available for JMB and they don't work.Does anyone know what the correct code is?

    I have JMB 24883 FULL-HD LED TV and have tried all remote codes off Sky, none worked. Big issue had was watching video demo AFTER attempting the codes which resulted in the last code entered displaying (off supplied list).I.E. in video it says to press TV, hold Select and red until flashes then type 990..1234, 1-1st digit, 2-2nd digit etc BUT having tried the supplied list this method just flashes the last entered remote code off that list!!How to reset?

  • How do I program my remote to work for my satellite and Blu Ray player?

    I recently purchased the 55 in LED Toshiba tv model number 42SL417U and I am having trouble finding the instructions on how to program it to work with my Sony Blu Ray player and Satellite. I went to product support and could not find a topic on how to program the remote. 

    Information on how to program your remote is available on page 79 of your user's guide.
    The TV also has CEC functionality to control other CEC-enabled, HDMI-connected devices. More information about this is on page 19 of the user's guide.
    - Peter

  • Sky remote doesn't work tv

    Just bought a Toshiba 32RV753 but my sky remote won't control it. Tried generic code from sky manual & also called sky but no joy. Can anyone help?

    Appletvs page dont mention. Anything about sky anything so not sure why you would assume it would

  • Sky+ Remote Code for Bush LED40127FHDCNTD 40" Full HD LED Smart TV (Rev 9 Remote) [Working]

    Hi, I wanted to pass on a code that I found that worked with the  Bush 40" Full HD LED Smart TV (LED40127FHDCNTD) (Argos item number 128/1684). I tried a few codes from a round the web but found 0065 to work with this model with a Rev.9 Sky+ remote. For the sake of completeness here are some of the other codes that I tried without success: 2060, 1354, 2155 (from the Sky Remote page) , 2242,1613 and 2153. Hopefully this might help someone out there!

    Hi,I'm looking for the Sky+ Remote Code for the same Bush TV  (LED40127FHDCNTD) but I have a Rev 10 Remote. It does not give me a Rev10 option when I try looking for the code on system....day26 wrote:
    Hi, I wanted to pass on a code that I found that worked with the  Bush 40" Full HD LED Smart TV (LED40127FHDCNTD) (Argos item number 128/1684). I tried a few codes from a round the web but found 0065 to work with this model with a Rev.9 Sky+ remote. For the sake of completeness here are some of the other codes that I tried without success: 2060, 1354, 2155 (from the Sky Remote page) , 2242,1613 and 2153. Hopefully this might help someone out there! 

  • TV/DVD 19lv506: Full DVD functions from side of unit? Programming TWC remote for DVD operation?

    Lost remote and need to operate all DVD functions from either TWC remote or from buttons on side of unit. So far, unable to program TWC remote to work DVD, though fine with TV. Can't seem to do anything but Play, Stop and Eject from buttons on side of TV. Can't Fast Forward, Pause, Rewind or access menu to select scenes, so must restart movies from beginning after taking a break and watching regular TV.

    I don't know if that's possible. You may want to check Toshiba Direct for a replacement remote. They have a shopping assistance phone number listed at the top as well.
    - Peter

  • Uninstall program on remote machine -

    All,
    I am trying to uninstall an application on a WYSE 32bit Windows Embedded device.  I am unable to use WIn32_product and have to Win32Reg_AddRemovePrograms.  I can query the device remotely fine with the following command
    PS C:\> get-wmiobject -Class Win32Reg_AddRemovePrograms -ComputerName rob_wyse | where {$_.Displayname -like "blah*"} | select ProdID | fw
    {548B747B-9B82-4FA7-91C8-15C8E8B053B1}
    My issue is I want to capture the output of the ProdID into a variable and then use invoke-command to call MsiExec to uninstall the program.  Below is what I have thus far..I was trying to use
    the "outVariable" with hopes that I could use Invoke-Command -ComputerName rob_wyse "MsiExec.exe /norestart /q/x '$prid'" to run the uninstall with MSIEXEC.
    What is the best way?  Where am I going wrong?
    get-wmiobject -OutVariable prdid -Class Win32Reg_AddRemovePrograms -ComputerName rob_wyse | where {$_.Displayname -like "Blah*"} | select ProdID | fw
    Invoke-Command -ComputerName rob_wyse "MsiExec.exe /norestart /q/x '$prid'"
    Thanks for the help.
    Rob
    Thank you for your help and time, Robert Jaudon

    You could try using psexec instead of invoke-command, but you wouldn't be able to execute the get-wmiobject command.  Is powershell even installed on it?
    In your script do this:
    $prodid = (get-wmiobject -OutVariable prdid -Class Win32Reg_AddRemovePrograms -ComputerName rob_wyse | where {$_.Displayname -like "Blah*"} | select ProdID).ProdId
    start-process psexec -argumentlist "-accepteula \\rob_wyse msiexec /X$ProdID /q /norestart" -PassThru
    This assumes you've installed psexec to system32 and is in your path, otherwise add the full path and filename in place of just 'psexec'
    Psexec info and download:
    http://technet.microsoft.com/en-us/sysinternals/bb897553.aspx
    Good luck!

  • How to execute program in remote server?

    In my code I am executing a program that resides on another
    server. But when I execute the program the server where the code is
    resided runs the program and sucks up CPU.
    How can I make it execute the program in the remote server? I
    don't want it to just fetch the exe and run it locally. I want it
    to execute the program IN the remote server, using ITS resources.
    The remote server is a network share, \\server2 for example.
    Any thoughts?

    You should be able to use <cfexecute...> to do this,
    you will have to
    make sure all the connections and permissions are set up.
    Just remember that by default, at least on windows systems,
    CF is
    configured to only have access and permissions to the local
    system, you
    will need to modify this if it has not been done.

  • Forms6: Execute program in remote machine?

    Hi,
    I'm trying to execute a program in a remote machine. For exemple: I can use the function 'host ('notepad')' and the notepad executes in the machine running the .fmx. How can I execute a command in a remote machine running Unix? Is there a function?
    I'm using Developer6 (forms).
    Thanks.

    You should be able to use <cfexecute...> to do this,
    you will have to
    make sure all the connections and permissions are set up.
    Just remember that by default, at least on windows systems,
    CF is
    configured to only have access and permissions to the local
    system, you
    will need to modify this if it has not been done.

  • TightVNC - Can't open programs on remote session

    Hi All,
    I'm a Linux newbie and have a problem I can't seem to solve. The other day I installed tightvnc and have a server which runs on startup. I have added the following line to /etc/inittab:
    vn:35:once:sudo su - brian -c "vncserver :1 -name Brian -depth 24 -geometry 1280x600"
    I also have the following in my xstartup file
    #!/bin/sh
    #xrdb $HOME/.Xresources
    #xsetroot -solid grey
    #xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" &
    #twm &
    xhost +localhost &
    exec startxfce4 &
    I am using UltraVNC on Windows 7 to remote into my arch box and I manage to get the XFCE4 desktop. The problem lies in trying to open programs on my remote session. If I click on the terminal shortcut, nothing happens. Same with Firefox etc.. I attempted to right click then execute and still no go.
    However, I am able to click the filesystem icon and it will open. Also, I can click on logoff and shutdown no problems.
    Any ideas?

    I use tightvnc as well, but I start it a bit differently (I don't think this is your problem).  Have you seen the tightvnc wiki article?  I updated it a while ago with the method that I use.
    Anyway, I don't think the & mark is needed in your ~/.vnc/xstartup
    $ cat ~/.vnc/xstartup
    #!/bin/sh
    xrdb $HOME/.Xresources
    export XKL_XMODMAP_DISABLE=1
    #exec ck-launch-session startxfce4
    exec ck-launch-session startlxde
    I dunno why your mouse isn't working properly if it's not something in that file.
    Last edited by graysky (2010-07-08 08:05:33)

Maybe you are looking for